WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6169318.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Wireless Module YL43752 IEEE 802.11a/b/g/n/ac/ax Wireless LAN, Bluetooth and FM receiver Combo Stamp Module 1. General Description With Bluetooth and dual band (2.4 GHz and 5 GHz) Wi Fi 2 2 MAC / baseband /
radio module. YL43752 supports IEEE 802.11 a/b/g/n/ac/ax. It is a highly integrated wireless local area network (WLAN) solution that allows users to enjoy digital content through the latest wireless technology without using additional cables and jumpers. It combines with Bluetooth and provides a complete 2.4GHz Bluetooth system which is fully compliant to Bluetooth and SDIO v3.0 that supports EDR of 2Mbps and 3Mbps for data and audio communications. It enables a high performance, cost effective, low power, compact solution that easily fits onto the SDIO and UART stamp module. Compliant with the IEEE 802.11a/b/g/n/ac/ax standard, YL43752 uses Direct Sequence Spread Spectrum (DSSS), Orthogonal Frequency Division Multiplexing
(OFDM), BPSK, QPSK, CCK and QAM baseband modulation technologies. A high level of integration and full implementation of the power management functions specified in the IEEE 802.11 standard minimize system power requirements by using YL43752. YL43752 module adopts BCM43752 single chip solution. The module design is based on the BCM43752 solution. 2. Key Features 1.High speed wireless connection up to 1201Mbps for Wi-Fi 2. Wi-Fi MIMO and Bluetooth 3.Low power consumption and high performance 4.Enhanced wireless security 5.Fully qualified BLE 1M 6.Enhanced Data Rate(EDR) compliant for both 2Mbps and 3Mbps supported 3. Specifications Table Model Name Description WLAN Standard Bluetooth Standard Major Chipset Host Interface Dimensions Wi-Fi VID/PID BT VID/PID Weight Operating Conditions Voltage Temperature Storage temperature Electrical Specifications Frequency Range Modulation Receive Sensitivity Data Rates YL43752 Wireless LAN &Bluetooth Stamp Module IEEE 802.11 a/b/g/n/ac/ax Bluetooth 2.1+Enhanced Data Rate (EDR)+ BLE 1M BCM43752 Wi-Fi : SDIO, BT :UART 15.2mm * 12.2mm * 2.0mm TBD TBD TBD 3.3V
-30~85
-40~125 WLAN:
2.4 GHz ISM Bands: 2412-2462MHz 5GHz: 5150-5250MHz; 5250-5350MHz; 5470-5725MHz;
5725-5850MHz
(Note: 5600-5650MHz was disabled by software in Canada Market.) Bluetooth:
2402~2480MHz WLAN:BPSK,QPSK,16-QAM,64-QAM,256-QAM,1024-QAM DBPSK,DQPSK,CCK BluetoothGFSK (1Mbps), /4 DQPSK (2Mbps),8DPSK
(3Mbps) 802.11b:-91.4 dBm (11Mbps) 802.11g: -78.7 dBm (54Mbps) 802.11n @2.4GHz: -77.2dBm (HT20 MCS7) 802.11ax @2.4GHz: -62.5dBm (VHT20 MCS11) 802.11a @5GHz: -76.3dBm (54Mbps) 802.11a @5GHz:-74.5 dBm (VHT20 MCS7) 802.11ac @5GHz:-74.5 dBm (VHT20 MCS7) 802.11ac @5GHz:-69.1 dBm (VHT40 MCS8) 802.11ac @5GHz:-64.2 dBm (VHT80 MCS9) 802.11ax @5GHz:-62.5 dBm (VHT20 MCS11) 802.11ax @5GHz:-59.7 dBm (VHT40 MCS11) 802.11ax @5GHz:-55.9 dBm (VHT80 MCS11) BT: BER < 0.1% (IQXEL80 Tx -70 Bm) WLAN 802.11b: 1, 2, 5.5, 11Mbps 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11n: up to 144.4Mbps (20MHz channel) 802.11n: up to 300Mbps (40MHz channel) 802.11ac:up to 173.4Mbps (20MHz channel) 802.11ac:up to 400Mbps (40MHz channel) 802.11ac:up to 866.6Mbps (80MHz channel) 802.11ax:up to 286.8Mbps (20MHz channel) 802.11ax:up to 573.5Mbps (40MHz channel) 802.11ax:up to 1201Mbps (80MHz channel) Bluetooth BLE 1M+EDR data rates of 1,2, and 3Mbps WAPI WEP 64-bit and 128-bit encryption with H/W TKIP processing WPA/WPA2Personal (Wi-Fi Protected Access) WMM/WMM-SA/WMM-PS (U-APSD) AES-CCMP hardware implementation as part of 802.11i security standard Security Operating System Compatibility TBD 4. Electrical Characteristics 4.1 Absolute Maximum Ratings Symbol Parameter VBAT 3.3V power supply voltage 5.0 VDDIO Voltage supply for GPIO 3.9 Maximum Unit V V 4.2 Recommended Operating Conditions Unit Symbol Parameter VBAT V VDDIO Voltage supply for GPIO 1.62~3.63 V Rating 3.3V power supply voltage 3.2~4.8 4.3 GPIODC Characteristics Minimum Typical Maximum Unit Symbol Parameter VIH VIL VOH VOL Input high voltage 0.65VIO --
Input low voltage
Output high voltage VIO-0.4
Output low voltage 0
-0.3 VIO+0.3 V 0.35VIO V V VIO V 0.4 5. Pin Definition Pin Description PinNo. Definition 1 2 3 4 5 GND WL_BT_ANT1 GND GND GND 6 BT_DEV_WAKE Basic Description Type GROUND Wi-Fi/BT RF signal GROUND GROUND GROUND Bluetooth device wake-up: Signal from the host to the BCM43752 indicating that the host requires attention. Type GND I/O GND GND GND I/O Asserted: The Bluetooth device must wake-up or remain awake. Deasserted: The Bluetooth device may sleep when sleep criteria are met. The polarity of this signal is software configurable and can be asserted high or low. Host wake up. Signal from the BCM43752 to the host indicating that the BCM43752 requires attention. Asserted: Host device must wake-up or remain awake. Deasserted: Host device may sleep when sleep criteria are met. The polarity of this signal is software configurable and can be asserted high or low. DC power supply +3.3V input GROUND Wi-Fi RF signal GROUND GPIO pin to on/off the Wi-Fi function by software. Active high. Reserve pull high 100K resistor and shunt 100pF capacitor to GND on platform. WLAN device wakeup host SDIO Data Line 2 SDIO Data Line 3 SDIO Command Input SDIO Clock Input SDIO Data Line 0 SDIO Data Line 1 GROUND ABUCK output to inductor 1.8V supply for WLAN I/O Input for MISCLDO and sense pin for ABUCK External low-power 32.768KHz clock input. PCM synchronous data output, connected to PCM_IN on the host. PCM Clock PCM synchronous data input, connected to I/O VCC GND I/O GND IN OUT I/O I/O I/O IN I/O I/O GND OUT VCC IN IN OUT I/O IN 7 BT_HOST_WAKE 8 9 10 11 VBAT GND WL_ANT2 GND 12 WL_REG_ON 13 14 15 16 17 18 19 20 21 22 23 24 WL_Host_WAKE SDIO_DATA2 SDIO_DATA3 SDIO_CMD SDIO_CLK SDIO_DATA0 SDIO_DATA1 GND ABUCK_1P12_LX VDDIO ABUCK_1P12 LPO_IN 25 BT_PCM_OUT 26 27 BT_PCM_CLK BT_PCM_IN 28 29 BT_PCM_SYNC GND 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 PCIE_REFCLK_N PCIE_REFCLK_P PCIE_RD_P PCIE_RD_N PCIE_TD_P CBUCK_0P9 GND XTAL_OUT XTAL_IN GND PCIE_PERST_L BT_UART_RTS_N BT_UART_TXD BT_UART_RXD BT_UART_CTS_N 45 GPIO15_SDIO_PCle_SEL 46 BT_REG_ON 47 PCIE_CLKREQ_L 48 PCIE_PME_L PCM_OUT on the host. PCM synchronous data SYNC GROUND PCIe differential clock inputs (negative and positive). 100 MHz differential. PCIe differential clock inputs (negative and positive). 100 MHz differential. Receiver differential pair (1 lane) Receiver differential pair (1 lane) Transmitter differential pair (1 lane) Sense pin for CBUCK GROUND XTAL oscillator output XTAL oscillator input GROUND PCIe system reset. This input is the PCIe reset as defined in the PCIe base specification version 1.1. UART Ready To Send, connected to CTS on the host. UART Transmit Data, connected to RXD of the host. UART Receive Data, connected to TXD of the host. UART Clear To Send, connected to RTS on the host. WLAN host select 0: PCIe 1: SDIO GPIO pin to on/off the BT function by software. Active high.Reserve pull high 100K resistor and shunt 100pF capacitor toGND on host. PCIe clock request signal which indicates when the REFCLK to the PCIe interface can be gated. 1 = the clock can be gated. 0 = the clock is required. PCI power management event output. Used to request a change in the device or system power state. The assertion and deassertion of this signal are asynchronous to the PCIe reference clock. I/O GND IN IN IN IN OUT IN GND OUT IN GND IN OUT OUT IN IN I/O IN OD OD This signal has an opendrain output structure, as per the PCI Bus Local Bus Specification, revision 2.3. CBUCK output to inductor Transmitter differential pair (1 lane) OUT OUT 49 50 CBUCK_0P9_LX PCIE_TD_P 6 Mechanical Information FCC WARNING:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC RF EXPOSURE STATEMENT:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C/E has been investigated. It is applicable to the modular. 2.3 Specific operational use conditions This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. 2.4 Limited module procedures Not applicable 2.5 Trace antenna designs Not applicable 2.6 RF exposure considerations To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 20cm from your body. 2.7 Antennas This radio transmitter FCC ID: T2C-YL43752 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. No. Antenna Type 1 PCB 2 3 Iron FPC ANT Antenna Gain Impedance BT/BLE/Wi-Fi ANT 1 Wi-Fi ANT 2 BT/BLE/Wi-Fi ANT 1 Wi-Fi ANT 2 BT/BLE/Wi-Fi ANT 1 Wi-Fi ANT 2 2.61dBi 3.08dBi 2.86dBi 3.28dBi 3.32dBi 4.18dBi 1.53dBi 3.03dBi 3.30dBi 3.25dBi 3.30dBi 3.25dBi 50 50 50 50 50 50 50 50 50 50 50 50 Frequency Range 2.4~2.5GHz 5.15-5.85GHz 2.4~2.5GHz 5.15-5.85GHz 2.4~2.5GHz 5.15-5.85GHz 2.4~2.5GHz 5.15-5.85GHz 2.4~2.5GHz 5.15-5.85GHz 2.4~2.5GHz 5.15-5.85GHz 2.8 Label and compliance information The final end product must be labeled in a visible area with the following" Contains FCC ID: T2C-YL43752 2.9 Information on test modes and additional testing requirements Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host. 2.10 Additional testing, Part 15 Subpart B disclaimer Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B ISEDC STATEMENT:
Operation of 5150-5350 MHz is restricted to indoor use only. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le fonctionnement de 5150-5350 MHz estlimit uneutilisation en intrieuruniquement. Le prsent appareil est conforme aux CNR d' Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The device comply with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. The equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Le prsent appareil est conforme Aprs examen de ce matriel aux conformit ou aux limites dintensit de champ RF,les utilisateurs peuvent sur lexposition aux radiofrquences et la conformit and compliance dacqurirles informations correspondantes. La distance minimale du corps utiliser le dispositive est de 20cm. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de classe b est conforme la norme nmb-003 du canada. This device is intended only for OEM integrators under the following condition: The transmitter module may not be co-located with any other transmitter or antenna. As long as the condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:
Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 1 condition ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the ISED cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization. Any company of the host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to RSS-247 and RSSGen requirement, only if the test result comply with RSS-247 and RSS-Gen requirement, then the host can be sold legally. Note Importante:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l' ISED ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. toute entreprise de l'hte qui installent ce dispositif modulaire avec limite approbation devrait effectuer l'essai des modules et des rayonnements non essentiels des missions rayonnes selon rss-247 et le cnr - gen, seulement si le rsultat d'essai conforme rss-247 et le cnr - gen, puis l'hte peut tre vendu lgalement. End Product Labeling The final end product must be labeled in a visible area with the following:
Contains IC: 10741A-YL43752. Plaque signaltique du produit final Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante:
Contient des IC: 10741A-YL43752. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. This radio transmitter [10741A-YL43752] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below:
Cet metteur radio [10741A-YL43752] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous:
No. Antenna Type 1 PCB 2 3 Iron FPC ANT Antenna Gain Impedance BT/BLE/Wi-Fi ANT 1 Wi-Fi ANT 2 BT/BLE/Wi-Fi ANT 1 Wi-Fi ANT 2 BT/BLE/Wi-Fi ANT 1 Wi-Fi ANT 2 2.61dBi 3.08dBi 2.86dBi 3.28dBi 3.32dBi 4.18dBi 1.53dBi 3.03dBi 3.30dBi 3.25dBi 3.30dBi 3.25dBi 50 50 50 50 50 50 50 50 50 50 50 50 Frequency Range 2.4~2.5GHz 5.15-5.85GHz 2.4~2.5GHz 5.15-5.85GHz 2.4~2.5GHz 5.15-5.85GHz 2.4~2.5GHz 5.15-5.85GHz 2.4~2.5GHz 5.15-5.85GHz 2.4~2.5GHz 5.15-5.85GHz Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Les types d'antennes non inclus dans cette liste qui ont un gain suprieur au gain maximum indiqu pour tout type rpertori sont strictement interdits pour l'utilisation avec cet appareil.