1
Products and accessories
Power Indicator
light
Status indictor
light
Type-c
Charing Case
Tapping Area
Auxiliary
Micro
Earphon
Main Micro
Working instructions
USB
Power on&Power off
2
Power On
-Open the charging case
Power Off
-Shut the charging case
Operations&Functions
3
Notice:
1 The earphones is using tapping mode, please complete the
required operations in tapping area;
2 If the time of tapping for twice is too short or too long, it may no
response or causes misoperations;
3 The method of pressing or touching can not make the corresponding
functions active.
TAP×3
TAP×2
TAP×2
TAP×2
TAP×2
TAP×3
TAP×2
TAP×2
TAP×3
TAP×2
TAP×2
TAP×3
TAP×4
TAP×4
Reset
4
When two earphones can’t be matched, please see below methods
to reset .
Steps
Indicator Light
1-
2-
3-
4-
5-
6-
7-
Delete the corresponding
Bluetooth connection:"CARD20"
in the phone Settings
\
Put the earphone into charging
case and keep it close
After closing,
it shows red light
Take out two earphone separately
and tap 5 times(separately or at
the same time) within 40 seconds
The red light of two
earphones flash 3 times
Put two earphones into charging
case and keep it close
After closing,
it shows red light
Take out two earphone separately
and tap 5 times(separately or at
the same time) within 40 seconds
The red light of
earphones are bright
for 3 seconds
Again put the earphones into
charging case and keep it close
After closing,
it shows red light
Take out the earphones, it will
rematch within 30 seconds
When it succeed in
matching, the blue
light flashes quickly
Indicator light description
5
power on
power off
Call in
Red light first,
then light out
Red light first,
then light out
Blue light flash
quickly
In charging
Finish charging
No matched
Red light
Blue light first,
then light out
Red and Blue
light flash
Waiting to be
matched with
phones
Blue light flash
Close
Open
In charging
White light flash
4 seconds, then
light out
white light flash
4 seconds, then
light out
Corresponding to
the battery white
light flash
Finish Charging
Reminder of low
battery
Three white lights
light on and light
out after 8 seconds
White light flashes,
light out after 4 seconds
5
Parameters
Bluetooth Version
Working hours
Distance
FREQ
Working hours
Accumulated working hours
Output of Charging Case
Charging time for earphone
Charging time for charging case
5.2
2.4-2.5GHz
10 meters
20-20KHz
5 hours
25 hours
300mAh
1 hour
2 hours
6
Notice
1- Try to use the minimum volume that we can accept,high volume for a long
period of time will lead to permanent damage to hearing;
2- Keep the earphones and accessories out of reach of children, Children
should be under of the adult supervision;
3- Don’t immerse the device in water for a long time. Avoid using this product
while swimming, diving or showering;
4-Don’t use this product in humid, dusty or near the magnetic field, to avoid
causing internal circuit failure;
5-Don’t disassemble, modify the device,or insert foreign matter into the device,
which may cause equipment damage;
6-Don’t put your finger or other parts into the hollow position of the charging
case, to avoid physical injury;
7-The shell of charging case is metal and the edge position is thin, please
avoid using it at full blast;
8-Don’t place the earphones in direct sunlight such as window, car dashboard;
9-Avoid storing the earphones in the environment below 15℃ or above 50℃;
10-Avoid charging the earphones or charging case in the environment below 0℃;
7
Note
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.