SET Smart Motorized Valve YS5002-UC Installation & User Guide Revision Jan. 02, 2023 Contents A B C D E F G H I J
. Welcome!
. Before You Begin
. In the Box
. Required Items
. Get to Know Your Smart Motorized Valve
. Install the App
. Add Your Valve to the App
. Installation
. About Control-D2D
. Using the App & 3rd-Party Services K L M N O
. Battery Replacement
. Factory Reset
. Firmware Update
. Troubleshooting
. Warnings P Q R
. Warranty
. FCC Statement
. Contact Us 01 01 03 03 04 05 06 08 10 12 13 14 15 16 17 18 19 21 A Welcome!
Thank you for purchasing YoLink products! We appreciate you trusting YoLink for your smart home & automation needs. Your 100% satisfac-
tion is our goal. If you experience any problems with your installation, with our products or if you have any questions that this manual does not answer, please contact us right away. See the Contact Us section for more info. Thank you!
Eric Vanzo Customer Experience Manager B Before You Begin Visit our Smart Motorized Valve support page on our website, for the latest installation guides, additional resources, information and videos by visiting:
www.shop.yosmart.com/pages/smart-
motorized-valve-product-support Or by scanning the QR code:
01 Download the most current version of the user guide by scanning the QR code:
NOTE:
These instructions are not intended to be inclu-
sive of all possible pipe and tting types, nor are they intended to be comprehensive instructions for inexperienced installers. If you are not com-
fortable with an installation like this, please consult or hire a qualied plumber. Instructions in this guide are based on a new installation, on copper pipe, with push-t threaded adapters. The Smart Motorized Valve can be installed on CPVC or PEX pipe using the appropriate male NPT thread to compression or push-t copper, CPVC or PEX adapters. YoLink recommends SharkBite brand ttings. Visit sharkbite.com or nd additional information on our Smart Motor-
ized Valve Support page. Local plumbing/building codes may require a standard non-electric or non-motorized valve for the main water shut-off - do not replace a non-electric shut-off valve with this motorized valve without rst consulting with the applicable code authorities. If installing this valve to shut off the main water line, we suggest installing this adjacent to the (non-electric) shut-off valve. Please use care when working with cutting and other tools than can cause bodily harm if not used properly!
02 C In the Box Motorized Valve Model:YS5002-UC Battery: AA x 2 FCC ID: 2ATM75002 Made in China S O SET PULL UP BEFORE MANUALLY OPEN/SHUT Smart Motorized Valve Batteries (Installed) D Required Items These tools or items may be required:
Pipe Wrench Locking Pliers Copper Pipe Cutting Tool Pipe Fittings
/Adapters Thread Seal Tape Sandpaper 03 E Get to Know Your Smart Motorized Valve The YoLink Smart Motorized Valve is a motor-
ized valve with an integrated YoLink valve con-
troller. To get to know your new Smart Motorized Valve, refer to the illustrations below. SET Manual Control Knob Lift, then turn either clockwise to shut the valve or counterclock-
wise to open the valve SET Button Multifunction button LED Indicator See LED Behaviors below Valve Position Indicator Window indicates the current position of the valve. O indicates open, S indicates shut. Slow Blinking Green Twice Connecting to hub Quick Blinking Green Control-D2D Pairing in Progress Quick Blinking Red Control-D2D Unpairing in Progress Slow Blinking Green Updating Fast Blinking Red Every 30 Seconds Low battery, replace batteries soon 04 LED Behaviors Blinking Red Once, Then Green Once Device start-up Blinking Red And Green Alternately Restoring to factory defaults Blinking Red Once Valve closing Quick Blinking Red Twice Valve is closed Blinking Green Once Valve opening Quick Blinking Green Twice Valve is open F Install the App If you are new to YoLink, please install the app on your phone or tablet, if you have not already. Otherwise, please proceed to the next section. Scan the appropriate QR code below or nd the YoLink app on the appropriate app store. Apple phone/tablet iOS 9.0 or higher Android phone/tablet 4.4 or higher Open the app and tap Sign up for an account. You will be required to provide a username and a password. Follow the instructions, to set up a new account. Allow notications, when prompt-
ed. You will immediately receive a welcome email from [email protected] with some helpful information. Please mark the yosmart.com domain as safe, to ensure you receive important messages in the future. Log in to the app using your new username and password. The app opens to the Favorite screen. This is where your favorite devices and scenes will be shown. You can organize your devices by room, in the Rooms screen, later. 05 G Add Your Valve to the App 1. Tap Add Device (if shown) or tap the scanner icon:
Scanner icon 2. Approve access to your phones camera, if requested. A viewnder will be shown on the app. Motorized Valve Model:YS5002-UC Battery: AA x 2 FCC ID: 2ATM75002 Made in China S O SET PULL UP BEFORE MANUALLY OPEN/SHUT 3. Hold the phone over the QR code so that the code appears in the viewnder. If successful, the Add Device screen will be displayed. 06 You can change the device name and assign it to a room later. Tap Bind device. If successful, the screen will appear as shown. Tap Done. 4. If the Smart Motorized Valve is not already on, press the SET button for a moment, until the LED illuminates briefly. 07 H Installation 1. Shut-off the water serving the pipe where the valve is to be installed. Drain the water from the pipe, by turning on a faucet, or by other method as required. 2. Depending on the adapter tting used, mea-
sure the length of pipe that must be cut, and mark the cut lines on the pipe, as shown below. SET 3. Cut the water pipe through the mark using a pipe cutting tool, then remove the cut section of pipe, as shown below. 4. Sand both ends of cut pipe, removing any burrs or rough edges. Use care handling the cut edges, which may be sharp! Wipe off the cut section of pipe with a clean cloth. 08 5. Install your adapter ttings in the pipe ends, per the manufacturer instructions. 6. Wrap each adapters threaded end with thread seal tape, per the tape manufacturers instruc-
tions, as shown below. 7. Install the Smart Motorized Valve on the adapter ttings, ensuring a secure connection at each tting, as shown below. SET 8. At the water valve or point of disconnection, turn the water on again. 9. Verify there are no leaks and no visible water at the pipe ttings or on the Smart Motorized Valve. 09 10. Test the Smart Motorized Valve several times by pressing the SET button and listening for the smooth closing/opening of the valve, and by checking the water flow at a faucet. The water should be completely turned off while the valve is in the shut position. 11. Test the operation of the valve by controlling it from the app. From the Rooms or Favorite screen, locate your Smart Motorized Valve, tap the image, then tap Close to turn off the water, and tap Open to turn it on. I About Control-D2D YoLink Control-D2D is our unique device to device control technology. Using YoLink Control-D2D, YoLink devices can be controlled without the Hub or an internet connection. (Use of YoLink Control-D2D is optional; you can use the Automation feature in the app OR use YoLink Control, but YoLink Control-D2D offers the benet of operation without the Hub or internet connection.) One device controls another, directly. A device that sends out commands is called the controller. A device that receives the commands is called the responder. Examples of a controller are a Water Leak Sensor, while examples of a responder are a Siren or the Smart Motorized Valve. 10 Pairing instructions:
1. To congure your Water Leak Sensor* as a controller, press and hold the SET button for 5-10 seconds, until the LED quickly blinks green, then release the button. 2. To congure your Smart Motorized Valve as the responder, ensure the valve is closed (manu-
ally, or by pressing the SET button), then press and hold the SET button for 5-10 seconds until the LED quickly blinks green, then release the button. Upon pairing, the LED will stop blinking. 3. Test your paired devices. Upon the detection of water at the leak sensor, the valve should automatically close. Please note: the valve will not open when water is removed from the leak sensor. The valve should be closed from the app or by pressing the SET button on the valve. 4. Repeat for other devices, as needed. Unpairing instructions:
1. At the leak sensor, press and hold the SET button for 10-15 seconds, until the LED quickly blinks green then red, then release the button. 2. At the Smart Motorized Valve, press and hold the SET button for 10-15 seconds, until the LED quickly blinks green then red, then release the button. 3. Upon unpairing, the LED on the leak sensor and the motorized valve will stop blinking and turn off. 11 4. Test your devices. The Smart Motorized Valve should no longer respond to a water leak detec-
tion at the leak sensor. 5. Repeat for other devices, as needed.
* Refer to the sensors user guide, as needed. Instructions for Control-D2D pairing can be found in each Control-D2D-enabled products user guide. J Using the App & 3rd-Party Services Please visit our websites Product Support page for the YoLink app guide and for product specic app settings and instructions:
www.yosmart.com/support-and-service 12 K Battery Replacement 1. Loosen the two battery cover screws and remove the battery compartment cover TOP Motorized Valve Model:YS5002-UC Battery: AA x 2 FCC ID: 2ATM75002 Made in China S O SET PULL UP BEFORE MANUALLY OPEN/SHUT 2. Replace both batteries, observing the polarity and orientation of each battery. 3. Replace the battery compartment cover and tighten the screws. 4. In the app, verify the Smart Motorized Valve is online and batteries are indicated as good. IMPORTANT!
The Smart Motorized Valve can be powered by alkaline or lithium batteries. Do not use rechargeable batteries. 13 L Factory Reset Factory reset will erase device settings and restore it to factory default settings. Doing a factory reset will not remove the device from your account and it will not harm the device, or lose any data or require you to redo your auto-
mations, etc. Instructions:
Hold the SET button down for 20-30 seconds, until the LED blinks red and green alternately. Then, release the button. (Holding the button down longer than 30 seconds will abort the factory reset operation) Factory reset will be complete when the LED stops blinking. PLEASE NOTE: Only deleting a device from the app will remove it from your account. Factory reset will not delete the device from the app. 14 M Firmware Update Your YoLink products are constantly being im-
proved, with new features added. It is periodical-
ly necessary to make changes to your device's rmware. For optimal performance of your system, and to give you access to all available features for your devices, these rmware up-
dates should be installed when they become available. In the Detail screen of each device, at the bottom, you will see the Firmware section, as shown in the image below. A rmware update is available for your device if it says #### ready now Tap in this area to start the update. The device will update automatically, indicating progress by percentage-complete. You may use your device during the update, as the update is performed "in the background". The LED will slowly blink green during the update, and the update may continue for several minutes beyond the LED turning off. 15 N Troubleshooting Symptom:
1. Device is offline
- If valve is not connected to the cloud, press the SET button on Smart Motorized Valve
- If Hub is offline, reconnect the Hub to the Internet and press the SET button on Smart Motorized Valve
- If Hub is not on, power on the Hub again and press the SET button on Smart Motorized Valve
- If valve is out of range with Hub, relocating the Hub may be required
- For a device with low-battery indicators or alerts or if the condition of the batteries is in question, replace the batteries with two new
"AA" batteries 2. Other issues, contact customer service, 831-292-4831 (M-F 9am - 5pm PST) or email 24/7 at [email protected] 16 O Warnings Please install, operate and maintain the Smart Motorized Valve only as outlined in this manual. Improper use may damage the unit and/or void the warranty Do not install or use the Smart Motorized Valve outside of the temperature and hu-
midity range listed in the Environmental section in Specications, on the Smart Mo-
torized Valve Support page While the Smart Motorized Valve is rain-
proof, to ensure optimal operation and life-
time of the Smart Motorized Valve, installing the Smart Motorized Valve with overhead protection from weather is suggested. Do not immerse the Smart Motorized Valve or allow it to be immersed in water Do not install or use the Smart Motorized Valve where it will be subjected to high tem-
peratures and/or open flame If your Smart Motorized Valve does get dirty, please clean it by wiping it down with a clean, dry cloth. Do not use strong chemi-
cals or detergents, which may discolor or damage the exterior and/or damage the electronics, voiding the warranty Do not install or use the Smart Motorized Valve where it will be subjected to physical impacts and/or strong vibration.Physical damage is not covered by the warranty 17 Power the Smart Motorized Valve only with two AA batteries (see below, regarding bat-
teries) Use only new, alkaline or lithium non-
rechargeable AA batteries. Do not use zinc blend batteries Do not mix new and old batteries Do not puncture or damage batteries. Leak-
age can cause harm on skin contact, and is toxic if ingested Do not dispose of batteries in re as they may explode! Please follow local battery disposal procedures To avoid damaging the Smart Motorized Valve, if storing the controller for an extend-
ed period, remove the batteries Please contact Customer Service before attempting to repair, disassemble or modify the device, any of which can void the war-
ranty and permanently damage the device P Warranty For warranty information, please visit our Smart Motorized Valve Support page. 18 Q FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Chang-
es or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener-
ates uses and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. 19 Q FCC Statement, Cont. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. PRODUCT NAME:
SMART MOTORIZED VALVE PARTY:
YOSMART, INC. TELEPHONE:
831-292-4831 MODEL NUMBER:
YS-5002-UC ADDRESS:
15375 BARRANCA PKWY SUITE J-107, IRVINE, CA 92618 USA EMAIL:
[email protected] 20 R Contact Us We are here for you, if you ever need any assis-
tance installing, setting up or using a YoLink app or product!
Need help? For fastest service, please email us 24/7 at [email protected] Or call us at 831-292-4831 (US phone support hours: Monday - Friday, 9AM to 5PM Pacic) You can also nd additional support and ways to contact us at:
www.yosmart.com/support-and-service Or scan the QR code:
Support Home Page Finally, if you have any feedback or suggestions for us, please email us at [email protected] Thank you for trusting YoLink!
Eric Vanzo Customer Experience Manager 15375 Barranca Parkway Ste. J-107 | Irvine, California 92618 2022 YOSMART, INC IRVINE, CALIFORNIA 21
