FCC ID: WSLYG1540002 RFID Reader Writer

YG-1540001/2 HARDWARE SPECIFICATION Document No TNS21252 PRODUCT DELIVERY HARDWARE SPECIFICAION MODEL NAME YG-1540001 YG-1540002 Tokyo Communication Equipment Manufacturing Co., Ltd. Hitachi High-Tech Nexus Corporation TNS21252 Rev1.0 1 YG-1540001/2 HARDWARE SPECIFICATION Table of Contents 3-4 Scope System Configuration 5 1. 2. 6-9 3. Aspect 10 Absolute Maximum Rating 4. Electrical Characteristics 10 5. 6. AC(ReferenceDataNowarranty) 10 7. RFID Tag Command list 11 8. Production Flow 12 12 9. Function Test 13 10. 13 11. 13 12. 13 13. Shipping Warranty Miscellaneous Revision History TNS21252 Rev1.0 2 YG-1540001/2 HARDWARE SPECIFICATION Scope This product is the 13.56MHz RFID R/W module. It supports the ISO/IEC15693. Product name :YG-1540001,YG-1540002 Main specification Item RFID Tag Communication Frequency I/F Communication Range 1 Operation temperature Operation humidity Dimension Legal regulation compliance Function ISO15693(Tag-it HF-I Plus/ProICODE SLI) 13.56MHz 7kHz 38400bps (+0.32%) Data Length 8bitStopBit:1bitParity: NONE error correction :BCC RS422/485 YG-1540001 Approximately 5mm65mm YG-1540002 Approximately 5mm45mm 0+50 2085RHno condensation YG-1540001 YG-1540002 Inductive read write communication equipment YG-1540001NoAC-21063 YG-1540002NoAC-21064 RoHS2 Compatible MAX 500mW 52.5mm20mm 40.5mm RoHS RF OUTPUT POWER

* The software specification refers to [command specification of YG-1540001/2]

1 Using RI-I03-112A-0338 x 22.5. It depends on the surround environment. CAUTIONWhen using this device in the final products outside Japan, use a power supply wire harness with aferrite core and a total length of 45cm. The ferrite core should be equivalent with E04SR150718/Seiwa Electronics. The above ferrite core should use with two turn(one roop). YG-1540001 Board Power and GND wire YG-1540002 Board Product wire Power and GND wire About 45cm About 45cm Core Core About 5cm About 5cm TNS21252 Rev1.0 3 YG-1540001/2 HARDWARE SPECIFICATION Supports Legal Regulation This product complies with the regulations of the Radio Law of the United States and Canada

(FCC, IC) and is certified. Model NameYG-1540001 FCC ID:WSLYG1540001 IC8213A-YG1540001 Model NameYG-1540002 FCC ID:WSLYG1540002 IC8213A-YG1540002 This device complies with Part 15 of the FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions

(1) This device may not cause harmful interference, and

(2) This device must accept any interference, including interference that may cause undesired operation. L'exploitation est soumise aux deux conditions suivantes

(1) Cet appareil ne doit pas causer d'interfrences nuisibles, et

(2) Cet appareil doit accepter toute interfrence, y compris les interfrences pouvant provoquer un fonctionnement indsirable. CAN ICES-3 (A)/NMB-3(A) FCC CAUTION NOTE Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. RF exposure compliance 1) To comply with FCC/IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. 2) This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Conformit l'exposition aux RF 1) Pour se conformer aux exigences de conformit d'exposition RF FCC/IC, une distance de sparation d'au moins 20 cm doit tre maintenue entre l'antenne de cet appareil et toutes les personnes. 2) Cet metteur ne doit pas tre co-localis ou fonctionner en conjonction avec une autre antenne ou metteur. TNS21252 Rev1.0 4 YG-1540001/2 HARDWARE SPECIFICATION YG-1540001-1 YG-1540001-2 System Configuration POWER SUPPLY RS422 RS422 Device Address is defined by the Hardware setting. YG-1540001-1 R3 Mounted YG-1540001-2 R4 Mounted YG-1540002 R3, R4, R5, R6 All not mounted TNS21252 Rev1.0 5 Aspect 3.1 YG-1540001 YG-1540001/2 HARDWARE SPECIFICATION TOP BACK UNITmm FR-4 Layer4 Material Thick 1.0mm Think of Copper 18m Margin 0.1mmm CN1 No 1 2 3 4 Name VCC3V TOOL0 RST GND For Programming Function TNS21252 Rev1.0 6 YG-1540001/2 HARDWARE SPECIFICATION Function CN2 SM06B-GHS-TBJST No 1 2 3 4 5 6 Name VIN GND A B Z Y POWER GND 422I/F A 422I/F B 422I/F Z 422I/F Y YG-1540001 is used with Moleded plastic case. (Specifications of plastic case may change) YG-1540001

< Plastic Case (example) >

When using this device for the final products outside Japan, indicate the FCC ID and IC lighting number on the surface of the plastic case with a label or the like. If you cannot attach a label, etc., refer to the FCC ID and IC lighting number described in this manual instead of indicated them(P4). TNS21252 Rev1.0 7 YG-1540001/2 HARDWARE SPECIFICATION 3.2 YG-1540002

< TOP > < BACK > UNIT (mm) Material Thick Think of Copper Margin FR-4 Layer4 1.0mm 18m 0.1mmm TNS21252 Rev1.0 8 PIN ARRAYS TH CT1 CT2 CT3 CT4 CT5 CT6 CT7 Wire Item Wire Length Terminate Attach

< For PCB >

YG-1540001/2 HARDWARE SPECIFICATION Function SIGNAL VIN GND A B Z Y FS1 POWER GND 422I/F A 422I/F B 422I/F Z 422I/F Y Photo Interrupter Description UL1061 AWG28 Line color is described in the figure below Contents 200mm(+20mm,-0mm) Not including terminals SIN-002T-1.0(JST) Solder SPND-002T-C0.5(JST) SXA-001T-P0.6(JST) PNIRP-03V-S(For), PNIRP-02V-S(For), XMP-02V(For) PNIS-03V(For), PNIS-02V(For), XMS-02V(For) For PCB For device For device housing retainer Insulated tube T-105-2 5,L=150mm

< For device >

Heat shrink tube F2(Z)2,L=4mm 7 pieces (Equivalent product possible) UNITmm 1 UL1061 AMG28 use 2 All materials are UL Certified 3 Each terminal should be crimped with a special crimping tool 4 Use contacts that match the connector and wire diameter TNS21252 Rev1.0 9 YG-1540001/2 HARDWARE SPECIFICATION YG-1540002 is used with Moleded plastic case. (Specifications of plastic case may change) YG-1540002 Wire Exit

< Plastic Case (Cylindrical Type) >

When using this device for the final products outside Japan, indicate the FCC ID and IC lighting number on the surface of the plastic case with a label or the like. If you cannot attach a label, etc., refer to the FCC ID and IC lighting number described in this manual instead of indicated them(P4). Absolute Maximum Rating Item Input Power RS422 Input Symbol VIN VA,VB,VY,VZ 5.5

-9 to 14 Unit V V Rating Memo IC:SN65HVD3080E/TI Vdd=5V Topt 0+50 Hopt 2085

%RH No condensation Operation Temperature Operation Humidity Electrical Characteristics Item Symbol Condition Power Logic Power GND Consumption Current VIN VDD GND IDD AC(Reference Data No warranty) VIN =5V VDD = 3.3V Item Symbol Condition Inventory Single Block Read Single Block Write Just RFID Communication Time Without RS422 Tu Tmr Without RS422 Twr Without RS422 Min. 4.8

Min. Rate Typ. 5.0 3.3 0

Rate Typ. 18 18 39 Max. 5.2

160 Max. Unit V V V mA Unit msec msec msec TNS21252 Rev1.0 10 No Command Name Function Code Tag-it HF-I Pro Tag-it HF-I Plus ICODE SLI Memo RFID Tag Command List Inventory StayQuiet ReadSingleBlock 4 WriteSingleBlock LockBlock ReadMultipleBlocks 7 WriteAFI 8 LockAFI 9 WriteDSFID 10 LockDSFID 11 GetSystemInformation 12 WriteSingleBlock BlockLength 13 Kill 14 WriteSingleBlockPwd H'01 H'02 H'20 H'21 H'22 H'23 H'27 H'28 H'29 H'2A H'2B H'90 H'A4 H'A5 YG-1540001/2 HARDWARE SPECIFICATION 1 1 1 1 1 1 2 2 2 2 YG-1540001 YG-1540002 Original TI Original TI Original 1ResultCode = NG_READER_RESPONSE_RECV 2ResultCode = NG_15693_FAILURE For details refer to JIS X 6323-3 FunctionCodes are described [command specification of PC-1540001/2]

Kill andWriteSingleBlockPwd refer to Tag-it HF-I Pro Transponder Chip/Inlays. Commands and Options. Reference Guide. Literature NumberSCBU008. November 2005 1 2 3 5 6 TNS21252 Rev1.0 11 Production Flow YG-1540001/2 HARDWARE SPECIFICATION Solder Print Components Mount Re-Flow Aspect Inspection Splitting PCB Wire Assemble Wire Aspect Inspect Test Final Aspect inspect Packing Mounting of electronic components Inspect about the condition of the PCB Split the sheet of the PCB Wire Assemble Inspect about the condition of the Wires. Function Test Inspect about the final production. Packing YG-1540002 Only Function Test YG-1540001 Insulation Resistance Voltage Writing Firmware RFID Communication Test YG-1540002 Insulation Resistance Voltage Writing Firmware RFID Communication Test Photo Sensor Test Item Content Test Item Content Over 10k 3.3V5 Success or Frailer 565mm No Re-try Over 10k 3.3V5 Success or Frailer 545mm No Re-try Success or Frailer TNS21252 Rev1.0 12 YG-1540001/2 HARDWARE SPECIFICATION We pack it so that quality isn't damaged during transportation. 0Shipping Warranty If any defect arises in the product mentioned in this document within six month after delivery, and Supplier is Assumed to be responsible for it, and such the product is undoubtedly out of specification, the product shall be returned and replaced with a new product or a re-tested product by Supplier at Supplier's cost. We do not assume any responsibility for the expenses of resulting damages caused from the under-mentioned cases even under warranty. Any defect and/or abrasion caused by force majeure such as natural hazard and abnormal voltage drop. Any defect and/or abrasion caused from displacement, drop, removal and/or transportation. Any modification or a party designated by Supplier. Improper handling, regardless intention or fault. Responsibility for over and short of final specification approved by customer. Any defect caused from aging such as degradation of painted surface and plated surface. Miscellaneous If you have any questions, it shall be settled after discussion. All right reserved, do not reprint this work without permission. Revision History Date Revision content 2021/11/15 1.0 First revision TNS21252 Rev1.0 13

1-2-12 Koudushima Toyonaka, Osaka 561-0841 Japan Tel: +81-6-6868-5030 Fax: +81-6-6868-5029 URL: www.yuyama.co.jp Date (02/December/2021) Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Confidentiality Request FCC ID: WSLYG1540002 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules, YUYAMA MFG. CO., LTD. hereby requests permanent confidential treatment of information accompanying this application as outlined below:

Schematics Block Diagrams Theory of Operation (Operational Description) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, Name: Takanori Kanenawa Title: Assistant Manager

1-2-12 Koudushima Toyonaka, Osaka 561-0841 Japan Tel: +81-6-6868-5030 Fax: +81-6-6868-5029 URL: www.yuyama.co.jp Date (02/December/2027) TUV SUD America Inc. 10 Centennial Drive Peabody, MA 01960, USA Dear Sir or Madam, We, YUYAMA MFG. CO., LTD., 1-2-12, Koudushima, Toyonaka, Osaka-fu, 561-0843, Japan, hereby authorize Mr. Hiroaki Suzuki of TUV SUD Japan Ltd., 5-4149-7, Hachimanpara, Yonezawa-shi, Yamagata, 992-1128 Japan (phone: +81-238-40-1681), to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. Yours sincerely, _ fiheinvut Marengurn-

Name: Takanori Kanenawa Title: Assistant Manager