FCC ID: 2ADM5-EP-0603 BT INIFINITY WRAP AST

INFINITY W i r e le s s H e a ds e t INSTRUCTION MANUAL Thank you for purchasing the Infinity Wireless Headset. This manual provides more information about the wireless headset, please read the instructions before using. Headset Overview Package Contents Infinity Wireless Headset x 1 pc Micro USB Charging Cable x 1 pc Instruction Manual x 1 Power On/Off Power on Press and hold down the On/Off Button for 3 seconds and the LED will flash in red and blue alternately. Power off Press and hold down the On/Off Button for 4 seconds and the LED will turn off. Pair Infinity Wireless Headset with your mobile device Headset Overview Micro USB Charging Cable:

USB Plug

(or other devices) within 32.8 Feet. 1. Keep the distance between your wireless headset and mobile phone 2. Power on the Infinity Wireless Headset 3. Activate the Bluetooth function on your phone within range and select 4. The LED lights in blue when paired successfully. BT Infinity Headset from the list shown. Attention: If the pairing is not successful within 5 minutes, the headset will power off, please repeat the pairing procedures to try again. Micro USB Plug Reconnect Infinity Wireless Headset to your mobile device Side:

Top:

When powered on, the headset will automatically connect with the last successfully paired device. Micro USB Charging Port Microphone Disconnect the headset from your mobile device Power off the headset; or Switch off the Bluetooth on your mobile phone; or Leave the headset 60ft away from your mobile phone or further. Vol+/

Next Song Vol-/

Previous Song On/Off Button Play/Pause Music Answer/End Call Answer/Reject a call FAQ When you receive a call, press the On/Off Button once to accept the call, or answer the call normally via your mobile phone. Long press On/Off Button to reject a call End a call Press the On/Off Button once to end the call or hang up your mobile phone. Functions Short press + Button to advance to next song Short press - Button to go back to previous song Long press + Button to turn up volume Long press - Button to turn down volume Charging your headset LED indicator light turns red when charging your headset LED indicator light turns off when your headset are fully charged Technical specification Driver Diameter: 10 mm Impedance: 32 Ohms Sensitivity: 96 dB +/- 3 dB Frequency Response: 20 Hz - 20 KHz Power Supply: Li-ion Battery 3.7V 55 mAh Playing Time: 1.5 - 2 Hours Charging Time: 2 Hours Bluetooth Range: 32.8 Feet Micro USB cable included. If the Infinity Wireless Headset cannot be paired with your device, please try the following:

Ensure that your headset are in pairing mode or reconnection mode. Ensure that Bluetooth search function of your mobile device is activated. If the Infinity Wireless Headset will not turn on:

Make sure the headset are fully charged. Can I change the battery for the headset?

Infinity Wireless Headset use a built-in non-detachable battery which cannot be removed. If the Infinity Wireless Headset cannot be recharged:

If you use a power outlet, ensure that the power supply is connected securely and the outlet works. If you use a computer, ensure that it is connected and the USB port is powered. Safety instructions for the lithium battery and charging the product

-The input voltage to the product is 5V 1A.

-In order to charge the product in safe manner and reliable conditions, please only adopt certified appropriate charger/ adapter for charging the product.

-Only charge the product at ambient temperatures between 10 deg C/ 50 deg F and 40 deg C/104 deg F.

-Do not heat above 70 deg C/158 deg F, eg. Do not expose to sunlight or throw into fire.

-Switch off the product after use.

-Please note that we wont take any responsibility for any wrong operation

(e.g. Voltage higher than 5V) as this may result in severe injury or loss of property, and we cannot control the operating process during the time the user using this product.

-In extreme cases, abuse or misuse of Lithium battery pack can lead to explosion, heat generation, fire development or smoke development. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. RF warning statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC ID: 2ADM5-EP-0603 Item# EP-0603 Made Exclusively for Five Below Distributed by Zeeva International Limited Suite 1006C-8, 10th Floor, Exchange Tower, 33 Wang Chiu Road, Kowloon Bay, Hong Kong, China Made in China Keep all relevant information for future reference

EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Date:04/03/2019

To:FEDERALCOMMUNICATIONSCOMMISSION AuthorizationandEvaluationDivision 7435OaklandMillsRoadColumbia,MD21046

TheRFchip,model:AC6916,installedinourproductBTINIFINITYWRAPAST

,(Modelnumber:EP0603,FCCID:2ADM5EP0603),whichsupportBluetooth BDR(GFSK),EDR(/4DQPSK),EDR(8DPSK),BLE,foruseintheUSmarketingthis chipwillnotsupport/enablethe8DPSKandBLE.And8DPSK,BLEfunctionhasbeen shieldedbythemanufacturerbyusingthesoftware.

Sincerely, Signature: PrintedName:AkshayPButani Tiltle:VicePresident

24MHz AC6916

) ; Crystal

) provides the clock signal for the Bluetooth chip. Bluetooth signals Circuit Description 1. Battery(3.7V)provides energy for the Bluetooth chip(

oscillator(

get through a matching circuit, and then transmitted to the space through the antenna 2402MHz2480MHz . When the product is connected, the product can be in twoway communication with other Bluetooth devices, and then the device's Bluetooth module sends Bluetooth signals into space, the product receives the Bluetooth signal through an antenna, transmission to the Bluetooth chip via matching circuit.

Zeeva Int Suite 100 33 Wang Tel: +852 E-mail: a ternational Lim 07B, 10th Floo Chiu Road, K 2-2868 0511 |

akshay.butan mited r, Exchange T Kowloon Bay, Fax: +852-25 ni@zeeva.c Tower,

, Hong Kong 524 1986 com FCC C Author rization 04/0 03/2019 FED DERAL CO OMMUNICA ATIONS C COMMISSIO ONS Aut thorization a and Evaluat tion Divisio on 743 5 Oakland M Mills Road Colu umbia, MD D 21046 Sub bject: Agent t Authorizat tion To w whom it ma ay concern:

We, Com app to th our

, Zeeva Inte mpliance La lication for hese matters behalf shal ernational L aboratories Equipment s. All acts c l have the s Limited the u Corporation t authorizati carried out b same effect undersigned n to act on i ion, includin by Bay Area as our own d, hereby au its behalf in ng the signi a Complian action. uthorize Bay n all matters ing of all do nce Laborato y Area relating to ocuments re ory Corpora elating ation on We,

, the unders signed, here eby certify th hat we are n not subject t to a denial o of federal b enefits, that t includes FC CC benefits s, pursuant t to Section 5 5301 of the Anti-Drug Abuse Act of 1988, 21 U U.S.C. 862. This s authorizat tion is valid d until furthe er written n otice from t the applican nt. Sinc cerely Your rs, Sign nature:

Prin nted Name:

Akshay P B Butani Titl QA-F e: Vice Pr FR-170-B resident