FCC ID: WP85I02001V Chat Pad Controller Keyboard for Xbox (Dongle)

FEATURES This lightweight backlit keyboard easily attaches to Xbox Wireless Controllers making it easier to navigate movies, message with friends, enter passwords, and more. No extra batteries required. SETTING UP YOUR CHAT PAD 1 Remove the USB dongle from the storage compartment in the Chat Pad and plug it into an open USB slot on the Xbox Series X | S or Xbox One console. 3 Attach the Chat Pad by aligning the plugs and gently pressing into place. Please see www.insigniaproducts.com for the latest Quick Start Guide and troubleshooting. Dongle Storage Compartment Power input Collapsible 3.5mm headset jack Flat size (WH): 304 130mm. Final folded size: 76 130 mm. QUICK SETUP GUIDE Chat Pad Controller Keyboard for Xbox NS-XB1CHATPAD PACKAGE CONTENTS Chat Pad Controller Keyboard 2.4Ghz Dongle Quick Setup Guide 2.4Ghz Dongle Rubber cover ATTENTION!

IF YOU HAVE AN OLDER CONTROLLER WITHOUT THE 3.5MM HEADSET INPUT YOU CAN SKIP STEP #2. 2 Lift the rubber ap open and fold the jack into a extented position. You can now proceed to the next step to attach this Chat Pad to a newer Xbox controller with a 3.5mm input. Before using your new product, please read these instructions to prevent any damage. Pairing button 3.5mm headset jack LED indicator Headphone / Ext port 5 Once properly installed, connect headset (style compatible with your controller) by directly connecting to the appropriate port on the Chat pad. Please note that only headsets supported by your wireless controller can be used with the chat pad. The standard headset output on the chat pad cannot be used unless your controller supports standard headsets. HOW TO RECONNECT THE CHAT PAD The Chat Pad should already be synced with the dongle out of the box. If it is not , we suggest that you try to pair the USB dongle to the Chat Pad. 1. Make sure the console and controller are powered on. 2. Unplug the USB dongle from the console. 3. Press and release the pair button on the Chat pad to initiate pairing. The LED indicator will blink rapidly to indicate sync discovery mode. 4. Plug the USB dongle back into the console immediately. 5. Once properly paired, the LED indicator will glow solid blue for 2-3 seconds to indicate successful connection before turning OFF. Note: In the process of pairing, if the Chat pad cannot detect the USB dongle within 15 seconds, the Chat pad enters sleep mode automatically. If this happens, you need to start the pairing process again. SPECIFICATIONS Applicable range Wireless technology Operating range Working current (stand by) Working current (working) Xbox Series X|S and Xbox One controller 2.4 Ghz

< 10 m

< 10 uA

< 40 mA Product dimensions Chat pad:

Dongle:

5.59 2.48 1.77 inches

(142 63 45 mm)

.72 .56 .24 inches

(18.4 14.1 6 mm) Operating temperature 41F~95F (5C~35C) A B OR A Ocial Microsoft chat headset B 3.5mm compatible headset A B TROUBLESHOOTING 1. The Chat Pad has no functionality?

Check that power input and 3.5mm headset jack on the Chat Pad is properly connected to that port on the controller. 2. Does the Chat Pad have its own power source?

No, the Chat Pad is powered by the Xbox Series X|S or Xbox One controller. 3. Can I use a headset while using the Chat Pad?

Yes, you can plug a 3.5mm compatible headset into the Chat Pad or use the ocial Microsoft chat headset. 4. Can I use the Chat Pad on the PC?

Yes, you are able to use the Chat Pad on the PC while using an Xbox One controller and the dongle is connected to the PC. Before using the Chat pad on PC, make sure the Chat pad is synced to the dongle. Other parties marks are the property of their respective owners. INSIGNIA is a trademark of Best Buy and its afliated companies. Registered in some countries. Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richeld, MN 55423 U.S.A., 2021 Best Buy. All rights reserved. Made in China ENGLISH V3-21-0906 4 The Chat Pad should already be synced with the dongle out of the box. The back-light of the Chat Pad should illuminate once the Chat Pad has been connected to a powered on controller. Caps lock Shift Backspace Space Enter Note: For superscript symbols, press the Shift key and the corresponding key at the same time. For example, Shift+1 to type !, Shift+2 to type @ .

: Changes or modications to this unit not expressly approved by the party responsible for LEGAL NOTICES FCC information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. IC statement:

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with FCC and Industry Canada radiation exposure limits set forth for an uncontrolled environment. Cet quipement est conforme l'exposition aux rayonnements Industry Canada limites tablies pour un environnement non contrl. ONE-YEAR LIMITED WARRANTY Visit www.insigniaproducts.com for details. CONTACT INSIGNIA:

For customer service, call 1-877-467-4289 (U.S. and Canada) www.insigniaproducts.com

Authority to Act as Agent Date: 14 September 2021 TUV Rheinland Group 762 Park Avenue Youngsville, NC 27596 To Whom It May Concern:

I appoint TUV Rheinland (Shenzhen) Co., Ltd. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with ZEN Factory Group (Asia) Limited / A5-B, 12/F, BLOCK A, HONG KONG INDUSTRIAL CENTRE, 489-491 CASTLE PEAK ROAD, KOWLOON, HONG KONG For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date:

12 months By Title On behalf of

Shirley Luo

(Print Name) Telephone

0760-28106482-882

(Signature) Production and Quality manger ZEN Factory Group (Asia) Limited

(Company Name) QF094234 Page 1 of 1 Revision 0

Date: 2021-08-31 Subject: Confidentiality Request for FCC 1D: WP85102001V and IC ID: 8632A-510200V Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Exhibit

~. Short Term X Permanent Block Diagrams X. Short Term External Photos X. Short Term _. Permanent Internal Photos Short Term X. Permanent Operation Description/Theory of Operation Short Term YX, Permanent Part List/Tune-Up Procedure Short Term X Permanent Schematics XX Short Term . Test Setup Photos J Short Term ~ Permanent Users Manual ZEN Factory Group (Asia) Limited has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: ;

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-

1705. Sincerely, By: Sh ( : Shirley Luo mature/Title) (Print name)