Zigbee Wireless Product CC2530 Zigbee Module SZ1 General Description The SZ1 RF Module is a low-power, highly integrated 2.4-GHz transceiver that suitable for systems targeting compliance with worldwide radio-frequency. Its a true system-on-chip solution for 2.4-GHz IEEE802.15.4,ZigBee applications. Electrical Characteristics Ta = 25C, VCC = 3.3V ITEM Voltage supply Transmitting current Receiving current Sleep consumption frequency Output power Receiving sensitivity Data rate Transmit distance Baud Rate Operating temperature Package size MIN 2.1 36 25 2.405 3.5 2400
-40 PARAMETER TYPICAL 3.3 38 26 0.3 4.0
-97 250 150 9600 MAX 3.6 40 27 2.485 4.2 115200 80 28202 mm UNIT V mA mA uA GHz dBm dBm Kbps m bps Zigbee Wireless Product Radio 2.4-GHz IEEE802.15.4 compliant RF transceiver Excellent receiver sensitivity and robustness to Interference, receiver sensitivity reach to
-97dBm Programmable output power up to 4.5dBm Suitable for systems targeting compliance with worldwide radio-frequency Accurate digital RSSI/LQI support datarate: 250 kBps 8051 MCU Powerful five-channel DMA 128KB in-system programmable flash, customization 32-,64-,256KB 8KB RAM with retention in all power modes CSMA/CA hardware support AES security coprocessor Battery monitor and temperature sensor 12-Bit ADC with eight channels and configurable resolution Two powerful USARTs with support for several serial protocols IEEE 802.15.4 MAC timer, general-purpose timers (One 16-Bit, Two 8-Bit) 32-kHz sleep timer with capture Watchdog timer 21 general-purpose I/O pins (19 4 mA, 220 mA) Hardware debug support Package Description Zigbee Wireless Product Pin typ Pin Description Pin name Pin type Description Pin namee VCC GND RESET_N P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 P2.0 P2.1 P2.2 ANT Note:
1. P2.3 and P2.4 connect to a 32768 KHz crystal. 2. Spring Antenna or PCB Antenna can be choice. 3. Read TI CC2530 datasheet for detail. Power Ground reset Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Antenna interface Description DC 2.03.6V GND CC2530 RESET CC2530 P0.0 CC2530 P0.0 CC2530 P0.2 CC2530 P0.3 CC2530 P0.4 CC2530 P0.5 CC2530 P0.5 CC2530 P0.5 CC2530 P1.0 CC2530 P1.1 CC2530 P1.2 CC2530 P1.3 CC2530 P1.4 CC2530 P1.5 CC2530 P1.6 CC2530 P1.7 CC2530 P2.0 CC2530 P2.1 CC2530 P2.2 50ohm TYWE1SDATASHEET Zigbeemodulemustbeoperatedwithanaccesspointthathasbeenapprovedforthe RegulatoryinformationfortheOEMsandIntegrators TheguidelinesdescribedwithinthisdocumentareprovidedtoOEMintegratorsinstalling ZigbeemoduleinnotebookandtabletPChostplatforms.Adherencetotheserequirementsisnecessary tomeettheconditionsofcompliancewithFCCrules,includingRFexposure.Whenallantennatypeand placementguidelinesdescribedhereinarefulfilledtheZigbeemodulemaybeincorporated intonotebookandtabletPChostplatformswithnofurtherrestrictions.Ifanyoftheguidelinesdescribed hereinarenotsatisfieditmaybenecessaryfortheOEMorintegratortoperformadditionaltesting and/orobtainadditionalapproval.TheOEMorintegratorisresponsibletodeterminetherequiredhost regulatorytestingand/orobtainingtherequiredhostapprovalsforcompliance
. ZigbeemoduleareintendedforOEMsandhostintegratorsonly. The countryofoperation. ChangesormodificationtoZigbeemodulebyOEMs,integratorsorotherthirdpartiesisnot permitted.AnychangesormodificationtoZigbeemodulebyOEMs,integratorsorotherthird partieswillvoidauthorizationtooperate This module is not masked, and the end user needs to increase the mask. InformationtoBeSuppliedtotheEndUserbytheOEMorIntegrator Thefollowingregulatoryandsafetynoticesmustbepublishedindocumentationsuppliedtotheenduser oftheproductorsystemincorporatingtheAmplifiedZigbeemodule,incompliancewithlocalregulations. Hostsystemmustbelabeledwith"ContainsFCCID: 2AHI9CC2530 ",FCCIDdisplayedonlabel. The instructionsasdescribedintheuserdocumentationthatcomeswiththeproduct.IntelCorporationisnot responsibleforanyradioortelevisioninterferencecausedbyunauthorizedmodificationofthedevices includedwiththewirelessadapterkitorthesubstitutionorattachmentofconnectingcablesand equipmentotherthanthatspecifiedbyIntelCorporation.Thecorrectionofinterferencecausedbysuch unauthorizedmodification,substitutionorattachmentistheresponsibilityoftheuser.IntelCorporation andauthorizedresellersordistributorsarenotliableforanydamageorviolationofgovernment regulationsthatmayarisefromtheuserfailingtocomplywiththeseguidelines. ThisdevicehasbeenevaluatedandshowncompliantwiththeFCCRFExposurelimitsunderfixed exposureconditions(antennasaregreaterthan20cmfromapersonsbody)wheninstalledincertain specificconfigurations. Thehostsystemshallhavealabelshowing:ContainsFCCID:2AHI9CC2530 WhentheuserselectsU.FLRFconnectorantenna,itrequirestheacompletetheantenna.thekind ofantennathatuserscanbeuse:2.4GRFantennaU.FL.RFconnector(antennatype:FPCantenna, Integralantenna
(Thegainofantenna:2.0dBi) Zigbee modulemustbeinstalledandusedinstrictaccordancewiththemanufacturer's TYWE1SDATASHEET FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 15.105 Information to the user.
(b) For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. The final end product must be labelled in a visible area with the following:
Contains Transmitter Module 2AHI92530