FCC ID: SVNDH-IPC-KX2-B CONSUMER CAMERA

Connecting Alarm Input/output The camera can connect to external alarm input/output device through digital input/output. Step 1 Connect alarm input device to the alarm input end of the I/O port. See the following picture. Device collects different states of alarm input port when the input signal is idling and being grounded. Device collects logic "1" when input signal is connecting to +3V to

+5V or idling. Mode A: Level application. Alarm outputs high and low level, and the alarm outlet is OD, which requires external pull-up resistance

(10K Ohm typical) to work. The maximum external pull-up level is 12V, maximum port current is 300mA and the default output signal is high level (external pull-up voltage). The default output signal switches to low level when there is alarm output (As long as the operating current below 300mA, the output low level voltage is Mode B: Switch application. Alarm output is used to drive external circuit, the maximum voltage is 12V and the maximum current is 300mA. If the voltage is higher than 12V, please use an additional electric relay. About the Guide be found in user interface. prior written notice.

- This quick start guide is for reference only. Minor difference might

- All the design and software here are subject to change without properties of their respective owners.

- Please visit our website or contact your local service engineer for more information. explanation.

- If there is any uncertainty or controversy, please refer to our final

- All trademarks and registered trademarks mentioned are the Device collects logic "0" when input signal is grounded. Step 2 Connect alarm output device to the alarm output end of the I/O port. The alarm output is open-drain output, which works in the following modes. Installing Camera Note:

Make sure that the mounting surface is strong enough to hold at least three times of the device weight. Step 1 Step 2 Step 3 Step 4 Drill screw holes on the mounting surface as the positioning map shows, and then put in the expansion bolts. Attach the camera pedestal to the mounting surface with the self-tapping screws. Connect the cable and start the camera. Loosen the adjust knob and adjust the camera to a proper surveillance position as needed. Step 5 Secure the adjust knob to fix the camera. Step 3 Log in to web interface, and configure alarm input and alarm output in alarm setting. The alarm input on the web interface is corresponding to the alarm input end of the I/O port. There will be high level and low level alarm signal generated by the alarm input device when alarm occurs, set the input mode to "NO" (default) if the alarm input signal is logic "0" and to "NC" if the alarm input signal is logic

"1". The alarm output on the web interface is corresponding to the alarm output end of the device, which is also alarm output end of the I/O port. Mounting Surface Positioning Map Expansion Bolt Self-tapping Screw Adjust Knob Camera Quick Start Guide Version 1.0.0 Camera 1 QSG 1 Positioning Map 1 IR LED PIR Detector Power Adapter 1 Screw Package1 Camera Introduction Operating With Imou App Ethernet Port Digital Input/Output Step 1 Indicator Light Built-in Mic Note: If you have installed the App, update it to the latest version. Scan the following QR code or search Imou in Google Play or App Store to download and install Imou App. Wait for booting to be finished, and then the camera indicator flashes with green light. Step 4 Step 5 Do the following operations to finish adding camera. Select Wi-Fi Wi-Fi XXXXXX1 Wi-Fi XXXXXX2 Wi-Fi XXXXXX3

. Wi-Fi Password Power Port Built-in Speaker Reset Button Micro SD Card Slot Note: Press and hold the reset button for 10 s to reset the camera. The pattern of the LED indicator is included in the following table. LED Indicator Status Device Status Off Red light on Green light flashing Green light on Red light flashing Green and red light flashing alternately Powered off/LED turned off Rebooting after reset Booting Device malfunction Waiting for network Operating properly Network connection failed Firmware updating Step 2 Step 3 Run Imou App, and then register an account for the first use. Connect the camera to power source with the power adapter. Note:

If you have more than one camera, do step 5 to add them one by one. If the Wi-Fi network has changed or the indicator status goes wrong, reset the camera, and then do step 5 to add it again. Mounting Surface

CONSUMER CAMERA as Cube 4MP Mov IPC-K42P 12VEEE1A MADE IN CHINA SAFETY CODE: ak 7 FCC ID:SVNDH-IPC-KX2-B SIN: SKO36CCYAJ221FF ZHEJIANG DAHUA VISION TECHNOLOGY CO.,LTD FCC Warning Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Confidentiality Request regarding application for FCC ID : SVNDH-IPC-KX2-B SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States No.1199, Bin'an Road, Binjiang District, Hangzhou, P.R. China Hangzhou, 310052, China Zhejiang Dahua Vision Technology Co., Ltd To:

From: Zhejiang Dahua Vision Technology Co., Ltd Regarding:

LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature:

Printed Name (on file with the FCC associated with the Grantee Code) Yolanda.chen Title: Senior Certification engineer Company Name: Zhejiang Dahua Vision Technology Co., Ltd.

Zhejiang Dahua Vision Technology Co., Ltd TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Date: 2019-11-21 Regarding: FCC ID: SVNDH-IPC-KX2-B To whom it may concern:

We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Zhejiang Dahua Vision Technology Co., Ltd. This authorization is valid until further written notice from the applicant. Name (Printed): Yolanda.chen Signature:

On behalf of Company: Zhejiang Dahua Vision Technology Co., Ltd. Telephone: 0571-28822025 Title: Senior Certification engineer