EN/CN-A01 Adventurer 4 / 4
User Guide P28 This guide is only applicable to FLASHFORGE Adventurer 4 3D printer 4 3D Content Notice Reference Chapter 1 Adventurer 4 1.1 - Component Introduction 1.2 - Packing Specification 06 07 Chapter 2 Introduction of User Interface 2.1 - Build 2.2 - Prepare 2.2.1 - Preheat 2.2.2 - Filament 2.3 - Settings 2.4 - Maintain 2.4.1 - Upgrade 2.4.2 - Log 2.4.3 - Calibration 2.4.4 - ChangeExtruder 2.4.5 - Maintain Chapter 3 Software Installation Chapter 4 Preparation of Device Chapter 5 Print Chapter 6 Q&A Chapter 7 Support and Service 01 08 08 10 10 11 12 13 13 13 14 15 15 02 05 06 16 16 17 21 27 Notice Safety Notice: please read and strictly follow all the safety warnings and notice below. Note Every printer has been tested before leaving factory. It is normal and will not be of trouble if there are filament residue remaining in the extruder or slight scratches on the plate. Work Environment Safety Keep your work place tidy. Do not operate Adventurer 4 in the presence of flammable liquids, gases or dust, which will cause fire in the high temperature generated by the equipment. Keep Adventurer 4 out of children and untrained peoples reach. Electrical Safety Always use the Adventurer 4 with a properly grounded outlet. Do not refit Adventurer 4 plug. Ungrounded / improperly grounded / refitted plugs will increase the risk of leakage of electricity. Do not use Adventurer 4 in damp environment or under the burning sun. Damp environment will increase the risk of leakage / exposure to the sun will accelerate the aging of plastic parts. To avoid device damage, please use the power supply provided by Flashforge. Avoid using the device during a thunderstorm. In case of uncertain accident, please unplug the device if you do not use it for long. Personal Safety Do not touch the nozzle and build plate during printing. Do not touch the nozzle and plate after printing to avoid high temperature scald Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and Do not operate the device while you are tired or under the influence of drugs, or mechanical damage!
gloves away from moving parts. alcohol or meditation. 02 Cautions Keep the inside of the device clean and tidy. Do not place metal objects into the chute at the bottom of the platform. Please clean up the remaining in time. It is recommended to operate outside the equipment. Any modifications to the device will invalidate the guarantee. Lower the build plate before loading/unloading filament. The distance between the nozzle and build plate should be kept for at least 50mm. Operate the device in well-ventilated environment. Never use the device for illegal activities. Never use the device to make any food storage vessels. Never put the prints into your mouth. Environment Requirements Temperature: RT 15-30; moisture: 20%-70%. Place Requirements The device must be placed in a dry and ventilated environment. The distance of the left, right and back side space should be at least 20cm, and the distance of the front side space should be at least 35cm. Device storage temperature: RT 0-40. Filament Requirements Its recommended to use the filaments offered by Flashforge, or from the brands accepted by Flashforge. Due to the different properties of filaments, you need to modify printing parameters when using those which are not offered by Flashforge. Filament Storage All polymers degrade with time. Do not unpack filament until necessary. Filament should be stored in clean and dry conditions. 03 Legal Notice All the information in this document is subject to any amendment or change without the official authorization from Flashforge. FLASHFORGE CORPORATION MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FCC Notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: [1] This device may not cause harmful interference, and [2] this device must accept any interference received, including interference that may cause undesired operation. Flashforge shall not be liable for errors contained herein for incidental consequential damages in connection with furnishing, performance or use of this material. This document contains proprietary information protected by copyright. Copyright 2021 Flashforge Corp. All Rights Reserved. 04 Reference Name Adventurer 4 Number of Extruder 1 Positioning Accuracy X/Y axis0.011 mmZ axis0.0025 mm Layer Resolution 0.1~0.4 mm Build Volume 220 x 200 x 250 mm 0.4mm (default) 0.6/0.3 mm(opt ional) Highest extruder Temperature 10~150mm/s 265/240 Nozzle Diameter Build Speed Filament Support Power Supply Device Size Package Size Software ABS/PLA/PC/PETG/PLA-CF/ASA/PETG-CF AC100-240V/4.5A,350W 500(L)*470(W)*540(H) mm 585(L)*570(W)*680(H) mm FlashPrint Input: 3MF/S TL/OBJ/FPP/BMP/PNG/JPG/JPEG Input/Output File FileOutput: GX/G File Connectivity USB Disk/ WIFI/ Ethernet Printing Environment 15-30 05 Chapter 1 Adventurer 4 1.1 Component Introduction 5. Filament intake cover 1. Power switch 2. Power socket 3. Filament cover 4. Spool holder 6. Front cover 7. Platform base 8. Build plate 9. Touch screen 10. USB 11. Ethernet input 6 7 8 9 10 11 5 4 3 2 1 13 14 15 16 17 18 19 12 20 21 06 14. Cable slot 15. Fan for cooling model 12. Extruder 13. Filament guide tube joint 16. Fan for cooling extruder 17. Buckle 18. Air duct 19. Nozzle 20. Camera 21. Air filter 1.2 Packing Specification 3D Printer Filament Power Cable After-Sales Service Card EN/CN-A01 Adventurer 4 / 4
User Guide P28 This guide is only applicable to FLASHFORGE Adventurer 4 3D printer 4 3D User Guide 0.4-265 Nozzle Adventurer 4 Equipped Screwdriver Unclogging Pin Tool Allen Wrench Grease USB Disk Leveling Card Filament Guide Tube Joint 07 Chapter 2 Introduction of User Interface Note The interface layout may change whenever there is an upgrade of firmware. The functions below are only for demonstration purposes. 2.1 Build Read print file from local memory card Read print file from the USB stick 1. Click [Build], and then choose the path to read the print le. 2. File list Tap model filefor file details. Long press model filemulti-selecting mode on. The nished prints will be marked. 08 Extruder temperature Build plate temperature Time used Speed Copy the le to the local memory card Amount and type of laments required Layer thickness Details Interface Pause/Resume printing Check more parameter settings and details More Settings You can change laments The switch of LED light Adjust printing parameters:
extruder temperature/
platform temperature/
printing speed ZUsed when the distance needs to be adjusted between the first printed layer and the extruder. The up and down arrows indicate that the extruder moves upward or downward. FanThe fan for cooling the model. Wind speed can be adjusted for printing different filaments. Click OK to save and apply the changed parameters. 09 2.2 Prepare 2.2.1 Preheat Prepare Preheat Filament Tap to set preheat temperature. Long press to set preheat temperature speedily. Turn ON/OFF the extruder or platform preheat Extruder highest preheat temperature: 265Its up to the chosen extruder Platform highest preheat temperature: 110 Temperature can be adjusted anytime during heating. 10 2.2.2 Filament Choose [Load], extruder will be heated to set temperature, then follow the instruction to finish loading. Note that fast+slow loading is automatically applied, just place the filament in the extruder gear. Do not push the filament into the tube. You may hear noise Load/Change/Manual Load when the loading is fast. Change Click on [Change], the extruder will be heated up to the preset temperature. Pull out the filament according to the instruction. Insert new filament in the filament intake until some resistance is felt. New filament coming out of extruder indicates a successful replace-
ment. Manual Click on [Manual], extruder will be heated up to preset temperature. Choose filament length, and choose [Load/Unload]. Note Note that manual mode should be preferred when there is remaining filament in the tube. 11 2.3 Settings The following functions are included in [Settings]: Move, Network, Fan, Language, Status, Camera, Brightness, Light, FilamentDetect, Buzzer, PrinterName, About, FactoryReset. Moveto move the extruder left or right, (note that the noise is normal if it moves past the farthest point of the left side), and to move the build plate back and forth,
(note that the noise is normal if it moves past the farthest point of the front side);
Networkconnect device to hot spot/WLAN/Flash Cloud/Polar Cloud Fanto turn on/off the fan Languageselect language Statusincluding device temperatureX/Y/Z positionetc. 12 Camera: Remote monitoring. Turn on the camera during printing, and turn on time-lapse, and time-lapse video can be recorded in the memory disk; it can be found in
[Pictures]; choose [Take Pic], the live scene is saved as images;
Brightness: Adjust the screen brightness;
Light: turn on/off the light on the extruder;
FilamentDetect: filament check sensor is on/off;
Buzzer: Turn on/off the sounds of device startup and screen click;
PrinterName: User can name the device;
About: information of this device;
FactoryReset: this device is restored to factory setting. 2.4 Maintain Maintain Upgrade Log Calibration ChangeExtruder Maintain 2.4.1 Upgrade When the device is connected to the network, it will be prompted to upgrade when the new firmware is released;
2.4.2 Log When the equipment has abnormal movements, the problem can be fed back to the official after-sales team of Flashforge by copying the log. 13 2.4.3 Calibration It is necessary to calibrate the distance between the nozzle and the platform after the first use or replacement of the nozzle;
Expert modeExpert mode is for experienced users to directly calibrate the distance. Click to make extruder move upwardsClick to make extruder move down-
wards. Normal Mode extruder calibration and 9-point leveling offset are included. Click on [Normal Mode] to start pre-calibration. The first point is to calibrate the initial distance between the extruder and the platform. Click on the up and down arrows to adjust the Z-axis deviation value. You can also sense if there is slight resistance by pulling A4 paper between them to decide the appropriate distance. In general, no further adjustment is needed. If large size model still cannot be printed after extruder calibra-
tion, or failure occurs due to uneven platform, please finish 9-point leveling by calibrat-
ing all 9 points. After calibration, the software will automatically calculate a mean value for compensation; when calibrating each point, the user can also adjust the z-axis deviation by clicking the up and down arrows; after compensation, the value can be calculated and applied. 14 2.4.4 ChangeExtruder After installing a new nozzle, please set the compensation value according to the temperature the replaced nozzle adopts to; the actual deviation range of the extruder:
-10 ~ 30. Click [next] to enter the extruder selection interface. Select the new nozzle to be installed and the maximum temperature during preheating will be set according to the selected nozzle. Please ensure that the installed nozzle is the same as the selected nozzle type, and click [Complete] to return to the maintenance interface. Note if a different nozzle is replaced, the default maximum temperature of preheating will change to the temperature of the replaced nozzle. 2.4.5 Maintain In case of errors or unclear operation, please check and operate according to the maintenance suggestions first. 15 Chapter 3 Software Installation Find the FlashPrint installation package in the USB disk and select the version corresponding to your system to install. Or you can download it from https://www.flashforge.com/download-center. Chapter 4 Preparation of Device The equipment has been leveled and calibrated before delivery, but due to transportation or other influences, the distance between nozzle and platform may change. It is recommended to conduct [Calibration] after unpacking. This step is optional, please refer to the interface function introduction before operation. 16 Chapter 5 Print Connect cable to printer;
turn on the switch, the screen lights up. Power Switch 1.Connect to power. 2. Load Filament: open the filament cover on the right side, insert the filament into the filament intake, push filament into the feeding wheel until some resistance is felt. Please make sure filaments are in the feeding wheel. Tap
[Prepare]-[Filament]-[Load]. Follow the instruction, filament coming out of the nozzle indicates a success. 17 Connection IP Address Auto-scan IP Port 192
. 168
. 2
. 122
8899 Connect Note When the user wants to use the browser to view images, the printer and PC must be in an intranet (that is, the printer and PC connect to the same router). 3.Model File Transfer Method 1: Wi-Fi Connection Tap [Settings]-[Network]-[WIFI], operate according to the instruction. Open FlashPrint, click [Print], then click [Machine Type], select [FlashForge Adventurer 4]. You can try to enter the IP address or scan it automatically. The IP address can be viewed in [settings] - [about]. Import stl or obj file into the slicer; after slicing, the printer will heat up and start printing automatically. Method 2: USB Device Files can be read in USB disk. Insert USB disk and select the files to print. 18 Method 3: Cloud FlashCloud 1Open FlashCloud website (https:cloud.sz3dp.com) to register an account. After the mailbox is activated, you can log in and use it; after logging in. Home My Printer
+ Add Printer The current printer is empty, please add a printer My Printer Name Registration Code Type Cn FlashCloud My Model My Job Model Library Add Printer All elds must be lled in Name Registration Code OK Cancel 2Click [My Printer] - [Add Printer]. Fill in the registration number (Registration Code) on page and name the printer. After clicking OK, the information will appear in the FlashCloud interface of the printer. Polar Cloud Register the Polar Cloud account in https://Polar3d.com. Inquire Polar Cloud PIN code. Turn on the Polar Cloud switch and enter account number and PIN after connecting Adventure 4 to network. 19 4.Model Removal Take out the removable build plate, and bend the plate to get the model. Note Nozzle and build plate are still hot after finishing printing, please wait for them to cool down before you operate. It is recommended to take the plate to the outside of the equipment for model removal, otherwise the model debris will remain in the equipment. Please keep the inside of the printer clean. 20 Chapter 6 Q&A Q1. How to unclog the nozzle?
Method1 Tap [Preheat], heat up the nozzle to the set temperature. Once completing heating, press the lament guide tube joint and pull out the lament guide tube. Check to see whether the lament is bent or laments cross-section is smooth. If not, cut it smooth, install the guide tube and lament back. Tap [Load]. If method 1 does not work out, use an unclogging pin tool to unclog lament. If method 1&2 do not work out, please replace the nozzle. Method2 Method3 Q2. How to replace the nozzle?
Note Power off before replacing nozzle! No power on operation!
1. 2. 3. 4. 5. Press the left and right clips and pull out the nozzle. Push in the lament through the lament intake manually, making it long enough to be cut o;
Rotate the lament spool anti-clockwise manually, making lament retreat a little;
Press the left and right clips, install the new nozzle. Make sure nozzle slot and bottom of extruder are on the same level. Tap [Prepare] -- [Load], lament coming out of the new nozzle indicates successful replacement. Buckle 21 Improperly installed with seam Properly installed with no seam Whether the extruder assembly is in place is judged as follows:
1.When installed, the extruder must be pushed to the end;
2.Check whether the installation is in place Touch the black buckle and the lower shell of the white extruder, make sure no hollows are felt Observe to make sure there is no large gap in the joint of the black buckle and the lower shell of the white extruder. Q3. Do we need to calibrate the extruder after replacing nozzle?
Yes, small errors may occur because of the calibration. To keep best printing quality, you need to calibrate it again. Q4. What can I do if no filament comes out of the extruder after I choose the file and the extruder moves normally?
1. 2. Check the filament guide tube, make sure the filament has been pushed into the extruder; if not, please tap [Load] till filament comes out;
check whether the extruder is clogged, if so, please refer to Q1. Q5. How to solve if the distance between nozzle and platform is too large(far away) or too small(that they collide)?
1. 2. 3. Tap[Maintain]--[Calibration]
The printer starts pre-calibrating. The rst point is to calibrate the initial distance between the extruder and the platform (see Z-axis deviation value). Click the up and down arrows to adjust the Z-axis deviation value. With the help of the leveling card, you can feel if there is any slight resistance to decide the appropriate distance. When the extruder is still unable to properly print a large size model after calibration, or when the model fails to be printed due to uneven platforms, please continue using this function. The machine will calibrate the remaining 8 points. After calibration is completed, the software will automatically calculate a compensation mean to compensate. When each point is being calibrated, the user can also adjust the Z-axis deviation by clicking the up and down arrows. After compensation is completed, the value is memorized and the extruder goes back to zero. 22 Q6. Can we use other brand filament which is not produced by Flashforge?
Adventurer 4 supports ABS, PLA, PC, PETG, PLA-CF, PETG-CF, etc., which have dierent ingredients. Adventurer 4 tests out default settings like temperature and lament output to ensure the best printing quality. Other brands of laments can be used with the parameters adjusted. Because the required temperature between dierent materials is slightly dierent, it is recommended to clean the previous laments before using new laments, otherwise it is easy to cause extruder blockage. Q7. Is Adventurer 4 compatible with all kinds of AC power input?
Adventurer 4 is equipped with a built-in 24V/13.3A power supplier, suitable for 100V-240V input voltage. Q8. Is Adventurer 4 capable of turning itself o automatically after printing job is nished?
No . Q9. What kinds of le formats does Adventurer 4 support?
Input: 3MF/STL/OBJ/FPP/BMP/PNG/JPG/JPEG Files. Output: GX/G files. Q10. Does Adventurer 4 support other cloud platforms besides FlashCloud?
Yes, Adventurer 4 interface is open up to all other cloud platforms. Q11. Is the ABS printing safe?
ABS filament will give off certain poisonous gas when heated up, please put the printer in well-ventilated condition when printing ABS. We suggest using non-toxic PLA filament when printer is near children. Q12. How to solve edge warping and weak adhesion?
Method1 Method2 Method3 Method4 Method5 Method6 Heating up the platform can increase adhesion between platform and model. Adding raft to model when slicing in FlashPrint. Apply solid glue to platform before printing. Use extruder calibration in expert mode or leveling calibration to reduce the distance between the nozzle and the platform. Make sure the platform is at. Complete 9-point leveling suggested. Apply extruder calibration to reduce the gap. 23 Q13. Is it a must to add a raft before printing the model?
Not necessarily. More filaments come out of the nozzle when printing the raft, higher success rate there will be. When the plate is heated, the adhesion between the model and the platform increases, which makes the model adhere to the platform well when printing, and also increases the success rate. Q14. After replacing the nozzle, printer status indicates that extruder temperature is 300, and the fan is also working. Why is this happening?
Note:
Note that the temperature setting in the slicer le might not match the highest temperature of the replaced nozzle. Errors:
Errors in temperature displaying indicate that the new nozzle is not properly installed, and the extruder temperature cannot be read by the sensor. Please plug out and install the extruder again, make sure that the extruder is pushed to the end, and the buckle and bottom of extruder are on the same level. Refer to Q2. Note Power o when replacing the nozzle. Q15. The extruder makes out chug noise and no filament comes out of the extruder, what is the problem and how to solve?
Filament has not loaded into extruder, which is most likely because the extruder is clogged or lament guide tube is not properly installed. Check the guide tube joint rst, if its normal, refer to Q1 for resolution. Q16. What is the difference between filament loading, filament replacement and manual mode?
Load: only load filament into the extruder Change:first unloading and then loading filament, from fast to slow;
Manual: slow loading. Note it is recommended to use manual mode during testing the nozzle unloading laments. Not recommended for loading laments. If it is used, please select the maximum length. Q17. Adventurer 4 starts printing when the distance between extruder and build plate is still large, causing filament unable to stick to plate. Calibrate the printer again or finish Homing again before giving it another go. Q18. Printing files cannot be found when using USB driver?
USB driver file is not correct. Adventurer 4 only supports FAT32 file system, please format USB driver into FAT32 file system. 24 Q19. How to connect to Polar Cloud?
1. 2. 3. 4. Open Polar Cloud website, and log in account. https://polar3d.com;
Click in Cloud Account on the right top corner, roll down the page to nd PIN code;
Open Polar Cloud on the printer, enter account number and PIN code;
Turn on the switch and connect to Polar Cloud. Q20. How to connect to FlashCloud?
1. 2. 3. 4. Open FlashCloud website: https://cloud.sz3dp.com/login.html;
Open FlashCloud interface or about on the printer;
Add the printer on FlashCloud website, enter name and registration code of printer;
Turn on the FlashCloud switch to connect the printer. Q21. How to use camera?
1. 2. Turn on camera to watch live video on the Cloud Time-lapse function will take 100 pictures during printing and makes a video. Note Pictures can contain up to 10 models, while videos 20 models. Q22. Operation of movement 1. 2. When the length is not selected, press the button to start the movement, and release the button to stop the movement;
When the length is selected, press to start the movement, release will not stop the movement until the corresponding length is reached. Note Pay attention to the distance when it moves along the side to avoid hitting the border. Q23. Noise in the gear when loading filaments?
The printer adopts fast-slow loading, make sure there is no remaining filament in the guide tube. Q24. What is expert mode in calibration?
In expert mode, the distance can be adjusted directly for experienced users. Details can be found in the calibration instructions for expert mode. Q25. How to set printing parameters during printing?
Set printing parameters in the printer. Note that adjustments might be delayed to take eect, or improper adjustments will aect printing quality, please set it with caution. 25 Q26. Wi-Fi connection failure?
1. 2. Please check if there are any special characters in the Wi-Fi hotspot name, if there are any, please modify them and try again;
Check your password for special characters, and if so, try again after you have modied it. Note Make sure the password is entered correctly. Q27. Firmware update Please do not disconnect the network during download or update to prevent update failure. Q28. Turn on the printer with white screen and no firmware 1. 2. If you hear the power-on sound, change the screen or the wiring;
If you cannot hear the power-on sound, please contact the supplier. Daily Maintenance Instructions:
When the printer is not used for a long time, apply grease on the guide rail, do it regularly every other month. Put laments in the drying box to prevent moisture. If it is used frequently, it is recommended to replace HEPA lter cotton once every 2 weeks. Replace as follows:
1.Open the front door of printer, and nd the air lter device indicated in the picture. 2.Open the air lter cover, put in a new cotton lter, and close the lter cover. 26 Chapter 7 Support and Service Flashforge team is on standby and ready to help you with any challenges you may have with your 3D printer. If the issues or questions are not covered in this User Guide, you can seek for solutions on our ocial website or contact us via telephone. There are solutions and instructions to common issues that can be found in our knowledge base. Have a look rst as most basic questions are answered there. http://www.ashforge.com The Flashforge support team can be reached by e-mail or phone between the working hours of 8:00 a.m. to 5:00 p.m. PST Monday through Saturday. In case you contact us during o-duty time, your inquiry will be answered the following business day. Note: Because of changing dierent lament the extruder maybe blockaded. Its not owing to quality issue, and outside the scope of 400 hours life. If users encounter this problem, please contact our after-sale department and nish clean work according to their instruction. Facebook Ocial Group Address: Flashforge Ocial User Group Emailsupport@ashforge.com Address: No.518 XianYuan Road, Jinhua City,Zhejiang Province, China S/N: FFAD******
F C C S t a t e m e n t T h i s e q u i p m e n t h a s b e e n t e s t e d a n d f o u n d t o c o m p l y w i t h t h e l i m i ts f o r a C l a s s B d i g i t a l d e v i c e , p u r s u a n t t o p a r t 1 5 o f t h e F C C R u l e s . T h e s e l i m i t s a r e d e s i g n e d t o p r o v i d e r e a s o n ab l e p r o t e c t i o n a g a i n s t h a r m f u l i n t e r f e r e n c e i n a r e s i d e n t i a l i n s t a l l a t i o n . T h i s e q u i p m e n t g e n e r a t e s , u s e s a n d c a n r a di a t e r a d i o f r e q u e n c y e n e r g y a n d , i f n o t i n s t a l l e d a n d u s e d i n a c c o r d a n c e w i t h t h e i n s t r u c t i o n s , m a y c a u s e h a r m f u l i n t e r f e r e n c e t o r a d i o c o m m u n i c a t io n s . H o w e v e r , t h e r e i s n o g u a r a n t e e t h a t i n t e r f e r e n c e w i l l n o t o c c u r i n a p a r t i c u l a r i n s t a l l a t i o n . I f t h i s e q u i p m e n t d o e s c a u s e h a r m f u l i n t e r f e r e n c e t o r a d i o o r t e l e v i s i o n r e c e p t i o n , w h i c h c a n b e d e t e r m i n e d b y t u r n i n g t h e e q u i p m e n t o f f a n d o n , t h e u s e r i s e n c o u r a g e d t o t r y t o c o r r e c t t h e i n t e r f e r e n c e b y o n e o r m o r e o f t h e f o l l o w i n g m e as u r e s :
R e o r i e n t o r r e l o c a t e t h e r e c e i v i n g a n t e n n a . I n c r e a s e t h e s e p a r a t i o n b e t w e e n t h e e q u i p m e n t a n d r e c e i v e r . C o n n e c t t h e e q u i p m e n t i n t o a n ou t l e t o n a c i r c u i t d i f f e r e n t f r o m t h a t t o w h i c h t h e r e c e i v e r i s c o n n e c t e d . C o n s u l t t h e d e a l e r o r a n e x p e r i e n c e d r a d i o / T V t e c h n i c i a n f o r h e l p . C a u t i o n : A n y c h a n g e s o r m o d ic a t i o n s t o t h i s d e v i c e n o t e x p l i c i t l y a p p r o v e d b y m a n u f a c t u r e r c o u l d v o i d y o u r a u t h o r i t y t o o p e r a t e t h i s e q u i p m e n t . T h i s d e v i c e c o m p l i e s w i t h p a r t 1 5 o f t h e F C C R u l e s . O p e r a t i o n i s s u b j e c t t o t h e f o l l o w i n g t w o c o n d i t i o n s : ( 1 ) T h i s d e v i c e m a y n o t c a u s e h a r m f u l i n t e r f e r e n c e , a n d ( 2 ) t h i s d e v i ce m u s t a c c e p t a n y i n t e r f e r e n c e r e c e i v e d , i n c l u d i n g i n t e r f e r e n c e t h a t m a y c a u s e u n d e s i r e d o p e r a t i o n . R F E x p o s u r e I n f o r m a t i o n T h i s e q u i p m e n t c o m p l i e s w i t h F C C r a d i a t i o n e x p o s u r e l i m i t s s e t f o r t h f o r a n u n c o n t r o l l e d e n v i r o n m e n t . T h i s e q u i p m e n t s h o u l d b e i n s t a l l e d a n d o p e r a t e d w i t h m i n i m u m d i s t a n c e 2 0 c m b e t w e e n t h e r a d i a t o r a n d y o u r b o d y . 27 1.1 -
1.2 -
2.1 -
2.2 -
2.2.1 -
2.2.2 -
2.3 -
2.4 -
2.4.1 -
2.4.2 -
2.4.3 -
2.4.4 -
2.4.5 -
Q&A 28 29 31 32 32 33 34 34 36 36 37 38 39 39 39 39 40 41 41 41 42 46 51 3D
50mm 29 15- 3020%-70%
20cm 35cm0-40 2021 4
@Copyright 2021 30 4 1 X/Y 0.011 mmZ 0.0025 mm 0.1~0.4 mm 220 x 200 x 250 mm 0.4mm 0.6/0.3 mm 10~150mm/s 265/240 ABS/ PLA/ PC/ PETG/ PLA-CF/ ASA/ PET G-CF AC100-240V/4.5A350W 500L*470W*540H mm 585L*570W*680Hmm FlashPrint
3MF/STL/OBJ/FPP/BMP/PNG/JPG/JPEGGX/G U/ /
15-30 31 1.1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. USB 11. 5 4 3 2 1 13 14 15 16 17 18 19 6 7 8 9 10 11 12 20 21 32 12. 14. 18. 20. 16. 13. 15. 17. 19. 21. 1.2 CN/EN-A01 4 www.sz3dp.com Adventurer4 3D 3D 3D 0.4-265 4 U 33 2.1 U 1. 2. 34
ZZ 35 2.2 2.2.1 265 110 36 2.2.2
37 2.3
///Polar
38 2.4 2.4.1 2.4.2 2.4.3 39 9 Z 99 Z 2.4.4
-10~30 40 2.4.5 UFlashPrint www.sz3dp.com 41 1. 2.
42 IP IP 192
. 168
. 2
. 122
8899 3. WiFi
--WiFiFlashPrint 4IPIP-
stlobj U UU U 43 1 httpscloud.sz3dp.com FlashCloud En
2-
Polar Polar Polarhttps//Polar 3d.com SettingsPIN Code PIN 4 Polar PIN 44 4. 45 Q&A Q1. 1 2 3 1 Q2. 1. 2. 3. 4. 5.
1. 2. 46 Q3. Q4. 1. 2. Q1 Q5. 1. 2. 3.
Z Z 8 Z Q6. 4ABSPLAPCPETGPLA-CFPETG-CF 4ABSPLAPCPETGPLA-CFPETG-CF Q7. 4 AC 424V/13.3A100V-240V Q8. 4 Q9. 4 3MF/STL/OBJ/FPP/BMP/PNG/JPG/JPEG GX/G Q10. 43D Cloud 4 Q11. ABS ABSHEPA PLA 47 Q12. 1 2 3 4 5 6 9 Q13. Q14. 300 Q2 Q15. Q1 Q16. Q17. Q18. U U4FAT32UFAT32 48 Q19. Polar 1. 2. 3. 4. Polarhttps://polar3d.com PIN PolarPIN PolarPolar Q20. Flash 1. 2. 3. 4. https://cloud.sz3dp.com/login.html Q21. 1. 2. 100 10 20 Q22. 1. 2. Q23. Q24. ?
, Q25. Q26. WiFi 1. 2. WiFi 49 Q27. Q28. 1. 2. 2HEPA 1. 2. 50 QQ www.sz3dp.com 8:005:00 QQ 400 400-8866023 QQ 2850862986 / 2850863000 / 2853382161 3DQQ206773820 518 S/N: FFAD******
51 Follow us Zhejiang Flashforge 3D Technology Co., Ltd. Address: No.518 XianYuan Road, Jinhua City,Zhejiang Province, China Service Hotline: +86 579 82273989 support@ashforge.com