all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User manual | Users Manual | 2.95 MiB | May 23 2023 / November 16 2023 | delayed release | ||
1 |
|
Internal photos | Internal Photos | 1008.78 KiB | May 23 2023 / November 16 2023 | delayed release | ||
1 |
|
External photos | External Photos | 264.08 KiB | May 23 2023 | |||
1 |
|
ID label and location | ID Label/Location Info | 83.14 KiB | May 23 2023 | |||
1 |
|
Antenna specifications | Test Report | 1017.12 KiB | May 23 2023 | |||
1 |
|
Attestation Statements | Attestation Statements | 92.27 KiB | May 23 2023 | |||
1 | Block Diagram | Block Diagram | May 23 2023 | confidential | ||||
1 |
|
Confidentiality | Cover Letter(s) | 129.73 KiB | May 23 2023 | |||
1 |
|
Letter Authorization | Cover Letter(s) | 44.94 KiB | May 23 2023 | |||
1 | Operational Description | Operational Description | May 23 2023 | confidential | ||||
1 |
|
RF Exposure | RF Exposure Info | 58.12 KiB | May 23 2023 | |||
1 |
|
Schematics | Schematics | 92.11 KiB | May 23 2023 | |||
1 |
|
Test reports | Test Report | 3.49 MiB | May 23 2023 | |||
1 |
|
Test setup photos | Test Setup Photos | 137.68 KiB | May 23 2023 | |||
1 |
|
US Agent Letter | Attestation Statements | 102.91 KiB | May 23 2023 |
1 | User manual | Users Manual | 2.95 MiB | May 23 2023 / November 16 2023 | delayed release |
SZ16-ZN/EN-A01 Adventurer 3 Pro 2 This guide is only applicable to FLASHFORGE Adventurer 3 Pro 2 3D Printer Content Preface Notice Terms Chapter 1: Adventurer 3 Pro 2 1.1 - Components Introduce 1.2 - Reference Chapter 2: Operating 2.1 - Unpacking 2.2 - Accessories 2.3 - Interface 2.3.1 - Build 2.3.2 - Tools 2.3.2.1 - Network 2.3.2.2 - Preheat 2.3.2.3 - Setting 2.3.2.4 - About 2.3.3 - Filament 2.4 - Print 2.4.1 - Load Filament 2.4.2 - Model File Transfer 2.4.3 - Print 2.4.3.1 - FlashCloud Print 2.4.3.2 - PolarColoud Print 2.4.4 - Model Remove 2.4.5 - Replace Filament 2.5 - The Guide of Using Camera 2.5.1 - FlashCloud Camera Use 2.5.2 - PolarCloud Camera Use 2.5.3 - The Switching Can Be Controlled Through the Cloud 2.5.4 - Error Handling Chapter 3: Q&A Chapter 4: Supports and Service 06 07 08 10 11 11 13 13 16 17 21 22 23 23 25 30 30 32 36 37 38 39 41 43 45 06 08 46 49 Preface Note: Each device must be tested before leaving factory. If there are some residues in extruder or some tiny scratches on the build tape, it is normal and wont aect the printing quality. On the completion of this User Guide, thanks all Flashforge engineers and the Flashforge 3D printer users for their unremitting eorts and sincere assistance. The Flashforge Adventurer 3 Pro 2 user guide is designed for the users to stars their printing journey with Flashforge Adventurer 3 Pro 2. Even if you are familiar with earlier Flashforge machines or 3D printing technology, we still recommend that please read this guide, as there is lots of important information about the Adventurer 3 Pro 2 for you to get a better 3D experience. For a better and more successful printing experience, you can refer to the following materials:
Quick Start Guide:
Users will nd the Quick Start Guide together with the printer accessories. The Quick Start Guide will help you start your print journey as soon as possible. Ocial Flashforge Website: www.ashforge.com The ocial Flashforge website contains the up-to-date information concerning Flashforge software, rmware, device maintenance and so on. Users are also able to get the contact information from there. 01 Notice Safety Notice: PLEASE READ AND STRICTLY FOLLOW ALL THE SAFETY WARNINGS AND NOTICE BELOW. Work Environment Safety Keep your work place tidy. Do not operate the printer in the presence of ammable liquids, gases or dust. Keep the printer out of children and untrained peoples reach. Electrical Safety Always use the printer with a properly grounded outlet. Do not ret Adventurer 3 Pro 2 plug. Do not use the printer in damp or wet locations. Do not expose the printer to burning sun. In case of device damage, please use the power supply provided by Flashforge. Avoid using the device during an thunderstorm. In case of uncertain accident, please unplug the device if you do not use it for long. Personal Safety Do not touch the nozzle and build plate during printing. Do not touch the nozzle after nishing printing. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Do not operate the device while you are tired or under the inuence of drugs, alcohol or medication. Cautions Do not leave the device unattended for long. Do not make any modications to the device. To lower the build plate before loading/unloading lament.
[The distance between the nozzle and build plate should be kept for at least 50mm]
Operate the device in a well-ventilated environment. Never use the device for illegal activities. Never use the device to make any food storage vessels. Never use the device to make any electrical appliance. Never plug the model into your mouth. Do not remove the models with force. 02 Work Environment Safety Temperature: RT 15-30 ; Moisture: 20%-70%
Place Requirements The device must be placed in a dry and ventilated environment. The distances of the left, right and back side space should be at least 20cm, and the distance of the front side space should be at least 35cm. Device storage temperature: RT 0-40 Filament Requirements Do not abuse the lament. Please make sure you use the Flashforge lament or the lament from the brands accepted by Flashforge. Nozzle Clogging and damage may be caused by non-Flashforge lament due to inappropriate material properties. Filament Storage All polymers degrade with time. Do not unpack lament until necessary. Filament should be stored at clean and dry conditions. Legal Notice All the information in this document is subject to any amendment or change without the ocial authorization from Flashforge. Flashforge makes no warranty of any kind with regard to this document, including, but not limited to, the implied warranties of merchantability and tness for a particular purpose. FCC Notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: [1] This device may not cause harmful interference, and [2] this device must accept any interference received, including interference that may cause undesired operation. Flashforge shall not be liable for errors contained herein for incidental consequential damages in connection with furnishing, performance or use of this material. This document contains proprietary information protected by copyright. Copyright 2023 Zhejiang Flashforge 3D Technology Co., Ltd. All rights reserved. 03 FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 04 Terms Build Plate The surface on which the Adventurer 3 Pro 2 builds an object Build Tape The black tape that covers Adventurer 3 Pro 2s build plate so that object can stick to the build plate well Build Volume The three dimensional amount of space that an object will use once it is completed. The largest build volume is 150*150*150mm. Extruder draws the lament from the spool, melts it and pushes it This integral extruder device installed on X-Axis. Extruder though a nozzle into the build plate. Nozzle Also called print head, which located at the bottom of the extruder where heated lament is squeezed out. Cooling Fan To cool the outer assembly of the extruder and gear motor Filament Cartridge A specic box for placing Flashforge lament, which is located on the right of printer. Filament Guide Tube A white plastic tube that guides the lament from the lament box to the lament intake Filament Intake An opening located an the top of the extruder Solid Glue Stick A solid adhesive used for making the model stick to the build plate rmly 05 Chapter 1: Adventurer 3 Pro 2 1.1 Components Introduce 1. Filament guide tube 2. Filament guide tube joint 3. Extruder base 4. Cooling Fan 5. Removable nozzle 6. Extruder cables 7. Clip 8. Led light 9. Air guide 10. Front door 11. Y-axis sliding slot 12. Platform base 13. Build plate 14. Touch-screen 15. USB stick input 16. Power switch 17. Power input 18. Spool holder 19. Filament cover 20. Filament cover handle 21. Moto 22. Filament intake 23. Filament feeding wheel 24. Top cover 25. Air outlet 26 Ethernet input 06 1.2 Reference Name Adventurer 3 Pro 2 Number of Extruder 1, Removable Print Technology Fused Filament Fabrication [FFF]
Screen Size 2.8color IPS Touch Screen Build Volume 150*150*150 mm Layer Resolution 0.1-0.4 mm Build Accuracy 0.2 mm Positioning Accuracy Z-axis 0.0025mm; XY-axis 0.011 mm Filament Diameter 1.75 mm [ 0.07 mm]
Nozzle Diameter 0.4 mm Build Speed 10-150 mm/s Software FlashPrint Support Formats Input: 3mf/stl/obj/fpp/bmp/png/jpg/jpeg File Output: gx/g File Memory Size 8 G OS Windows XP/Vista/7/8/10, Mac OS, Linux Input 150W [24V, 6.25A]
Connectivity USB Stick, Wi-Fi, Etherbnet Device Size 388*340*405 mm Net Weight 9 kg 07 Chapter 2: Operating 1.1 Unpacking 1. Open the box. 2. Take out the wrapping paper box on the top. 3. Be careful! Filament and power cable are all placed inside the wrapping paper box. 4. Take out the printer from the box. 08 5. Plug the power cable into the input on the back and turn on the power switch, the touch screen is turned on. Power Switch X: 20.00 Y: 45.00 Z: 36.00 Y z x Status Language Move Camera Calibration Homing Filament Check Led 1/3 2/3 6. Click [Tools]-[Setting] in turn to enter page like this, turn to page two, click [Move]. Click the upper arrow in the moving page to make the extruder raises for removing the paper box on the bottom easier. 7. Open the front door, take out the paper box inside the printer, the printer unpacking completed. 09 2.2 Accessories 3D Printer Filament Power Cable After-sales service card Quick Start Guide 0.6-265 Nozzle Screwdriver Unclogging Pin Tool Allen Wrench Grease Leveling Card PEI Flexible Build Plate Glue Stick 10 2.3 Interface Menus Introduction Note: The interface layout may change whenever there is an upgrade of rmware. The functions below are only for demonstration purposes. 2.3.1 Build Read the print le from:
The local memory card The USB stick The Cloud Back: back to upper interface 1. Tap [Build]. 2. Choose the red path of the print le list. 1/1 1/1 3. File list Tap to begin printing; tap the picture of the selected le to enter le details. Page-ip: Tap the left/right arrow. 1/3 Long press the le picture or le name, quit out multi-selected interface, you can select all, copy , delete . Tap to quit out multi-selected interface. 11 File details: Including le picture, time needed, lament needed. Build: To begin printing the le. Copy: To copy the les to the local memory card from the USB stick. Delete: To delete the print le. Print interface Cancel: To cancel the print job. Pause/Resume: To suspend or resume the print job. More: To check more settings and details information during printing. Details Extruder temperature Build plate temperature Used time Printing progress Whole lament needed More Replace: To change lament during printing progress. Led Light: To turn on or turn o the led light. Detail: To check more detail information. 12 2.3.2 Tools Network: To connect the printer to your PC or the Internet. Preheat: To preheat the extruder and build plate. Setting: To implement relevant function setups. About: Information about the printer. 2.3.2.1 Network Wi-Fi ON/OFF: To turn on/o the Wi-Fi connection. Wi-Fi connection: To connect your printer with your PC via a stable Wi-Fi signal. 1/3 13 Hot spot To set your printer as a WLAN hots pot. Turn on/o the WLAN hot spot. Hots pot setting: To set the hots pot name and password. Input hots pot name with numbers, characters and symbols. Tap to save the name and password. Ethernet Connection To connect your printer with your PC via Ethernet cable. 14 Cloud Connection 1. Turn on the Wi-Fi or Ethernet connection, connect the printer to Internet successfully. 2. Tap [Tools] - Tap [Network] - Tap [Cloud] on the printer. 3. Turn on the Cloud Connection function. 4. Register your cloud account and set your setting on https://cloud.sz3dp.com with the registration code on printers touch screen, or register your cloud account on http://polar3d.com to set your polar3d account and pin code. 15 2.3.2.2 Preheat setting ON/OFF: Turn ON/OFF the extruder or platform preheat. Tap symbol, you could set preheat temperature. Long press symbol, set preheat temperature rapidly. Extruder/Platform preheat interface 265/265 265
/265 75/100 It contains actual temperature, target temperature and heating progress. Extruder highest preheat temperature: 265 Platform highest preheat temperature: 100 Tap : Abort the preheat job. Abort 16 2.3.2.3 Setting Network Preheat Status Language Move Camera Setting About Calibration Homing Filament Check Led 1/4 2/4 Buzzer Factory Reset NozzleCheck AutoCalibration Update Extruder 3/4 4/4 Setting interface Status Language Calibration Homing Move Camera Filament Check Led Buzzer Factory Reset Update Extruder Nozzle Check Auto Calibration 17 It displays the real-time coordinates of X-axis, Y-axis, Z-axis and the real-time temperature of extruder and platform. Status Status Language Calibration Home 1/4 Language Status Language Calibration Home 1/4 1/2 2/2 Choose the target language. Calibration Click the arrow to adjust the nozzle so that it just touches the platform Status Language Z axis Extruder OK Calibration Homing 1/4 Up arrow: Extruder will elevate, away from the platform;
Down arrow: Extruder will descend, move close to the platform;
18 Calibration:
Extruder Calibration:
Click on [calibration] to start pre-calibration. The rst point to calibrate the initial distance between the extruder and the platform [see z-axis deviation value]. Click on the up and down arrows to adjust the Z-axis deviation value. You can also feel if there is slight resistance by pulling A4 paper or leveling card between them to decide the appropriate distance. Homing Status Language Calibration Homing Homing, please wait... Homing completed 1/4 Yes Yes To make the X, Y and Z axes back to the mechanical zero point. X: 20.00 Y: 45.00 Z: 36.00 Y Z Move Camera X Filament Check Led 2/4 Manual:
To manually adjust the positions of the extruder and build plate. Extruder moves to the right;
Extruder moves to the left;
Build plate moves to the front;
Build plate moves to the back;
Extruder moves upward;
Extruder moves downward;
19 Move Camera Camera:
Turn on or turn o the camera. Filament Check Led 2/4 More details about Camera, please check Chapter 2.5. Move Camera Move Camera Filament Check Led Filament Check Led 2/4 2/4 Filament check:
To turn on/o the lament check, notice will pop out when lament is used up or suspended when the check is turned on. LED:
To turn on/o the light. Buzzer Factory Reset Factory Setting Delete all data in internal memory Completed!
Restored to factory setting Update Extruder 3/4 OK Start 20 Please select extruder 240 265 Buzzer Factory Reset Update Extruder 3/4 1/2 NozzleCheck AutoCalibration NozzleCheck AutoCalibration 4/4 4/4 2.3.2.4 About Factory Setting:
Delete all data in internal memory, return the printer to factory setting. Buzzer:
To turn on/o the buzzer. Update:
To update printer rmware. Extruder:
Select the nozzle type. Nozzle Check:
use temperature to calibrate after changing extruder. Auto Calibration:
When the calibrated extruder fails to satisfactorily print a large model, or failure occurs due to uneven platform, please to use automatic leveling. Machine Type:
Firmware Version:
Wi-Fi Mac Adventurer 3 Pro 2 v1.03-1.1 02:00:00:00:11:66 Serial No.:
123456 Register Code:
XXXXXX Polar Serial No.:
XXXXXX Build Volume:
150x150x150 Usage counter:
12 hours IP address:
10.90.243.184.8899 1/3 2/3 3/3 Shows the basic information about the printer. Notice: When contacting after-sales support, please give your Serial No to after-sales engineer, which is showed in the [About] interface. 21 2.3.3 Filament Load Change Manual Load 240/265 265/265 265/265 Heating extruder... Preheat completed. Begin loading. Press OK when new color appears Cancel OK OK The extruder is heated up to the target temperature. After heat completed, insert the lament into the extruder at an upright angle until some resistance is sensed [as the lament is pushed through the feeding wheel]. Load will complete when you see lament come out of extruder. 265/265 Unloading the lament, please wait... 265/265 Pull out lament, feed new lament, press [OK]
265/265 Please insert the lament OK OK Load Change Manual Change The extruder is heated up to the target temperature, after heat completed, lament will be unloaded from the extruder. Pull out the lament according to the instruction. Insert new lament into the lament intake, tap [OK] ;
New lament will be pushed into the extruder, replace will complete when you see new lament come out of extruder. Load Change Manual 100 mm 200 mm 300 mm Load Manual operate Wait until the extruder is heated up to the target temperature, choose the loading length, click on [Loading];
Load the laments, make a push until the resistance is felt;
Gear set works. Filaments coming out of the extruder in dicates a success. 22 2.4 Print Plug the power cable into the input on the right side and turn on the power switch, the touch screen is turned on. Power Switch 2.4.1 Load Filament 1. Open the lament cover, insert the lament into the lament intake, push lament into the feeding wheel until some resistance is sensed. Note: Please make sure lament has been pushed into the feeding wheel!
23 Build Tools Filament Load Change Manual 240/265 Heating extruder... Cancel 2. Tap [Filament] - Tap [Load] - After load completed - Tap [OK]
265/265 265/265 Preheat completed. Begin loading. Press OK when new color appears OK OK 3. Load completed when you see lament come out of extruder, Tap [OK]. Put the spool of lament on the spool holder, close the lament cover. Mind the loading direction of lament, make sure to be clockwise as the picture showed. 24 2.4.2 Model File Transfer After generating the Gcode le, you can transfer it to your printer with dierent network methods. If use USB stick to print, please insert your USB stick with target .g/.gx le to your printer, there will be no need to set new network. Method 1:
Wi-Fi Connection Network Preheat Wi-Fi Hot spot Setting About Cloud Ethernet 1. Tap [Tools] - Tap [Network] - Tap [Wi-Fi]. WiFi Choose a network Flashforge ChinaNet-AnCr TP-LINK_EDC2 QS_1234 1/3 123 abc
WiFi Flashforge Choose a network ChinaNet-AnCr TP-LINK_EDC2 QS_1234 1/3 2. Choose a network and input the password. 3. Open the FlashPrint software, click the icon at the bottom left corner of the interface to select the [Machine Type]., select [Flashforge Adventurer 3 series]. Then click [Print] -
[Connect Machine]. 25 4. In the pop up dialog box, the connection mode selects Automatic Scan or ll in the IP port column with the IP address of the printer. Query IP address clicking [Tools] -
[About], turn to next page, you can see the IP address. Input completion and click connect. 5. When the printer is connected successfully, the [Multi-Machine Control] interface will pop up where you can view the printer connection status. In this case, it will display the printer as a connected status.After processing the model in FlashPrint software, click the top print icon. Click [Start Slicing]-[Slice]. Select the appropriate location to save the slice processed les. Notices When the user wants to use the browser to view the images, the printer and PC must be in an intranet [that is, the printer and PC connect to the same router]. 26 6. After the software slicing is completed, click [Send to printer]. Then the printer starts preparatory work such as preheating, and automatically starts printing after it is ready. 27 Method 2: Cloud Connection Network Preheat Wi-Fi Hot spot Setting About Cloud Ethernet FlashCloud PolarCloud FlashCloud Printer Name:
Flashforge Registration Code:
ABCDEF PolarCloud Account:
PIN:
Save Use the cloud connection to process printing operation.
* The use of Flashforge cloud is in 2.4.3.1 section. 28 2.4.3 Print Build Tools Filament 6.62 GB Not Available No Job 1. Tap [Build], choose the le path: Printer internal memory, USB stick, Cloud. Ship-PLA.gx 20mm_Box-
PLA.gx 1/1 2. Choose the model le, tap on its right to start printing; or tap model picture or model name to enter detail page, tap to start printing. 20mm_Box-P... 0 h 10 min 0.70 M Ship-PLA.gx 20mm_Box-PLA.gx Build completed h min Time Remaining OK 1/1 3. Extruder will heat up automatically, when heating nishes, the printer will start to build the model. After printing completed, printer will sound a beep and pop out a notice on the touch screen. 29 2.4.3.1 FlashCloud Print FlashCloud: Cloud.sz3dp.com 1. Register your account on Flashforge cloud:
After activate your account through your email box, login in Flashforge cloud with your account. Login E-mail Password Remember Password Login Forgot password Register My Printer Name Add printer The current printer is empty. Please add a printer. Register code Type State FlashCloud Home My Printer My Model My Job Model Library 2. After login in cloud with your own account, click [My Printer] - click [Add Printer]. My Printer Name FlashCloud Home My Printer My Model My Job Model Library Add printer The current printer is empty. Please Register code Printer Name:
FlashCloud Add Printer All elds must be lled in Name Registration Code OK Cancel Registration Code:
ABCDEF 3. Input your printers name and Flashcloud registration code in [Add printer] interface. These information are showed in your printers FlashCloud interface. 30 My Printer Name Add printer The current printer is empty. Please add a printer. Register code Type State Flashforge ABCDEF Adventurer 3 Pro 2 Idle FlashCloud Home My Printer My Model My Job Model Library 4. Add printer completed. User 2023.3.2 FlashCloud Home My Printer My Model My Job Model Library 3D Model Model Detail Print 5. Choose a model from cloud model library or upload your own model [.stl le], click [Print], enter the edit model interface to edit model. FlashCloud Home My Printer My Model My Job Model Library Flashforge Edit model Print para Move Rotate Scale 150 150 150 0 0 0
-150 X:
-150 X:
-150 X:
Print 6. In the drop down menu of the printers name, your can choose the printer which runs this mission. [The printer must be added into my printer]
31 Flashforge FlashCloud Home My Printer My Model My Job Model Library Time Remaining 0 0 h min 0%
21/0 21/0 Closed Nomal Start Cancel 2.4.3.2 PolarCloud Print 1. Register Polar cloud account. Log in http://polar3D.com to register the account. 2. Query Polar cloud PIN code.
[1]. After completing the Polar cloud registration and log in the Polar cloud website, click the icon on the top right corner and click [Settings]. 32 Location Biography Website URL http://www.example.com/prole Email
+ ADD Email PIN Code XXXX 2. Find the PIN Code column below the page, and the shown number is PIN code. 3. Connect the Adventurer 3 Pro 2 to the Internet. Choose the appropriate network connection mode in the communication interface to connect the network [see the 2.3.2.1 section of the connection method]. 4. Connect the Adventurer 3 Pro 2 to the Polar cloud. PolarCloud Account:
PIN:
Save Polar cloud switch Enter the cloud connection interface [click tools >
communication > cloud connection], turn on the Polar cloud switch [After the Polar cloud is turned on the switch will change into green]. Fill in the below account and PIN code columns with the account before the registration of Polar cloud and the PIN code queried before, click save. 5. After the connection is completed, you can see the printers information on the front page of Polar cloud website. [If you turn on the camera function, you can see the time picture on the page]. 33 6. Click [MY OBJECTS], then click [UPLOAD] to upload the model. 7. Drag and drop the model les that need to be uploaded to the box area or click the box area to select the upload model, then click [UPLOAD] to upload. 34 8. Click [PRINT]. 9. Click [START], the printer starts the cloud task downloading, and starts printing when the download is nished. 35 2.4.4 Model Remove As showed in picture, grasp the handles on both sides of the platform directly with both hands, and pull outwards to remove the build platform. Notices When printing completed, extruder and build plate may still hot, please start operating after cooling down!
Please use the back side of the build plate when printing with PETG. Please remove models after the platform has cooled down. If models are removed when the platform is not completely cooled down, bubbles will occur on the surface of the platform. It is recommended to take the platform to the outside of the equipment for model removal, otherwise the model debris will remain in the equipment. Please keep the inside of the printer clean. 36 2.4.5 Replace Filament Load 240/265 Change Heating extruder... Cancel 1. Tap [Filament] - Tap [Change], extruder will start preheating. 2. Pull out the lament as the picture showed above. 3. Insert new lament into the lament intake and push the lament into the feeding wheel until resistance is sensed. 265/265 Unloading the lament, please wait... 265/265 Pull out lament, feed new lament, press [OK]
265/265 Please insert the lament OK OK 4. When new lament come out of extruder steadily, replace is completed, Tap [OK]. 37 2.5 The Guide of Using Camera Camera User Manual The use of Adventurer 3 Pro 2's camera is introduced as follows. Build Tools Filament Network Preheat Move Camera Setting About Filament Check Led 2/4 1. Tap [Tools] - [Settings] on the second page - [Camera], the user can click the [Camera]
button to open it. Build Tools Filament 2. After the camera is turned on successfully, the icon of camera will appear in Status Bar. 38 2.5.1 The use of Flashforge cloud camera 1. Login Flashforge cloud website and register an account. After the mailbox activation, you can login and use the Flashforge cloud. Flashforge cloud website:
http://cloud.sz3dp.com Login E-mail Password Remember Password Login Forgot password Register My Printer Name Add printer The current printer is empty. Please add a printer. Register Type State FlashCloud Home My Printer My Model My Job Model Library 2. After login, click [My Printer] - [Add Printer]. My Printer Name FlashCloud Home My Printer My Model My Job Model Library Add printer The current printer is empty. Please Register code Printer Name:
FlashCloud Add Printer All elds must be lled in Name Registration Code OK Cancel Registration Code:
ABCDEF 3. Fill in the printer page with the printer name and registration code in [Add printer] interface. These information are showed in your printers FlashCould interface. 39 FlashCloud Home My Printer My Model My Job My Printer Name Add printer The current printer is empty. Please add a printer. Register code Type State Flashforge XXXXXX Adventurer 3 Pro 2 Oine Model Library 4. Add succeed. ad3 pro 2 5. Click the camera icon pointed by the arrow. ad3 pro 2 6. Camera begins to work. 40 2.5.2 PolarCloud camera use 1. Register Polar cloud account Emter www.polar3D.com website to register account. 2. Find Polar cloud pin code.
[1]. After registering Polar cloud and log in Polar cloud website, click the upper right arrow, click [Settings]. Location Biography Website URL http://www.example.com/prole Email
+ ADD Email PIN Code XXXX
[2]. Find PIN Code on the bottom of the page, the display numbers is PIN code. 41 3. Connect Adventurer 3 Pro 2 to the Internet. Choose the proper connecting way in the Network interface [the connecting way consults pagexx]. 4. Connect Adventurer 3 Pro 2 to the Polar cloud PolarCloud Account:
PIN:
Polar cloud switch Enter the cloud connection interface [click Tools- Network-
Cloud], turn on the Polar cloud switch [After the Polar cloud is turned on, the switch will change in to green]. Save Fill in the bottom account and pin code column Polar account an pin code showed before respectively, click [Save]. After the connection is completed, you can see the camera image in Polar cloud website. Notices 1. Make sure the printer is connected to the Internet. 2. When using the camera please make sure the camera is in the camera status instead of USB status.
[There should be a camera icon in the status bar.]
42 2.5.3 The switching can be controlled through the Cloud 1. Connect to Polar Cloud The user can turn on or turn o the camera through Polar Cloud. Click Tools->
Communication -> Cloud Connect -> Polar Cloud, enter the settings page of Polar Cloud, click the input boxes of account number and PIN, enter the account number and PIN, click the Start button to connect to Polar Cloud. The account number is the mailbox used for sign-up with Polar Cloud; for the acquisition of PIN. PolarCloud Account:
PIN:
Save The way of getting PIN code The guide of getting a Polar could account. The Polar could account is the register email account. Polar cloud website: www.polar3D.com.
[1]. After registering Polar cloud and log in Polar cloud website, click the upper right arrow, click [Settings]. 43 Location Biography Website URL http://www.example.com/prole Email
+ ADD Email PIN Code XXXX
[2]. Find PIN Code on the bottom of the page, the display numbers is PIN code. 2. Open or close the camera though the cloud.
[1]. After switching on the camera function, click camera image on the front page to enter the interface like this, click the COMMANDS button pointed by the arrow. open camera close camera
[2]. You can use check mark to open or close the camera in the pop-up window. CANCEL SEND 44 Notices a. If Polar cloud is in an intranet [that is, the printer and PC connect to the same router], the video is shown, and the state of printing can be displayed in real time. If Polar cloud is in an extra-net, the pictures are shown [in case of printing, a picture is sent per 20s;
in case of not working, a picture is sent per 60s]. b. When the camera is turned on or o, the lower computer will turn o and reconnect Polar cloud, so Polar cloud will not respond for a while. The recovery time depends on the state of network. 2.5.4 Error Handling PolarCloud Account:
PIN:
Error Conrm Save If the lower computer does not connect to Polar cloud and the printer has is deleted from the Cloud, the error is reported; at this point, the factory settings can be restored in order to solve the problem. After the lower computer connects to the printer and the printer is deleted from the Cloud, the sign-up needs to be done again according to the foresaid steps. 45 Chapter 3: Q&A Q1. How to solve if the nozzle is clogged Method 1: Tap [Preheat], heat up the extruder to 240, after heating completed, press the air tube joint and pull out the lament guide tube. Check to see whether the lament is bended or lament tip is not smooth, cut lament tip smooth and at, install the guide tube and lament back, Tap [Load] . Method 2: If method 1 not improving, use an unclogging pin tool to unclog lament. Method 3: If method 1 and method 2 not improving, please replace the nozzle. Q2. How to replace the nozzle?
Notices Power o before replacing nozzle! Make sure power o operation!
Please make lament tip smooth and at when cutting o the lament. 1. Press the left and right clips and pull out the nozzle. 2. Push in a length of lament through the lament intake manually, making it long enough to be cut o. 3. Rotate the lament spool anti-clockwise manually, making lament retreat back a little. 4. Press the left and right clips, install the new nozzle back into the extruder, making the nozzle slot and bottom of extruder are on the same level. 5. Tap[Filament] -- Tap[Load], nozzle replace completed when you see lament come out of new nozzle. Buckle The buckle is installed in place The buckle is not installed in place Whether the assembly of the extruder is in place is judged as follows:
1. When installing, must press the extruder hard to the end. 2. Check whether the installation is in place:
[1] Touch the black buckle and the white sprinklers lower shell, make sure no sunken.
[2] Look at the black buckle and the white sprinklers lower shell, make sure there is not a large gap in the contact. 46 Q3. Do we need to do extruder calibration again after replacing nozzle?
Yes, do extruder calibration again to ensure high print quality as minimal error may be caused by extruder installation. Q4. How to solve if displayed temperature is abnormal after replacing nozzle?
Abnormal temperature indicates extruder sensor can not be read, please check the nozzle whether it is well installed. Q5. How to solve if no lament come out of extruder after tap [Build] model le and extruder begins moving normally?
1. Check the lament guide tube, make sure lament has been pushed into the extruder, if not, please tap [Load]. Restart building model le after you see lament come out of extruder. 2. Check the nozzle whether it is clogged or not, if so, please refer to Q1 for resolution. Q6: How to replace the lament ?
1. Tap [Filament] - Tap [Replace], after extruder heating up completed, lament will be unloaded, pull out the lament according to the instruction. 2. Insert new lament into the lament intake and feeding wheel, tap [OK]; New lament will be pushed into the extruder. 3. Replace will complete when you see new lament come out of extruder. Q7: How to take down the model ?
1. Take out the removable build plate. 2. Bend the build plate, the plate will produce certain deformation, separating the plate away from the bottom of model. [Please use a scraper to assist removing when model is too small or too big]. 3. Take down the model. Q8: How to solve if the distance between nozzle and platform is too large [far away] or too small [hit] during printing?
1. Tap[Setting]--Calibration. 2. The extruder homing automatically, moves down some height. 3. Tap up and down arrow to adjust the distance between extruder and platform until extruder is just about to touch platform. 4. Tap[OK], printer will memorize current calibration position and start homing automatically. Q9: Can we use other brand lament which is not produced by Flashforge ?
Adventurer 3 Pro 2 support normal ABS and PLA lament but dierent brand lament has dierent ingredients. Adventurer 3 Pro 2 tests out default settings according to the properties of Flashforge ABS and PLA lament. Other brand lament is ok but not recommended for using, if that causes extruder clogging or bad printing quality or other failure, FlashForge will take no responsibility. These problems are not in the warranty of FlashForge . Q10. Is Adventurer 3 Pro 2 compatible with all kinds of AC power input ?
Adventurer 3 Pro 2 is equipped with a built-in 24V/6.5A power supplier, suitable for 110V-240V input voltage. Q11. Is Adventurer 3 Pro 2 capable to be turned o automatically after printing job is nished ?
No. 47 Q12. What kinds of le formats does Adventurer 3 Pro 2 support?
Input: 3mf / stl / obj / fpp / bmp / png / jpg / jpeg les. Output: gx/g les. Q13. Does Adventurer 3 Pro 2 support other cloud platform besides the FlashCloud?
Yes, Adventurer 3 Pro 2 interface is open up to all other cloud platforms. Q14. Is the ABS printing safe?
ABS lament will give o certain poisonous gas when heated up, please put the printer in well ventilated condition when printing ABS. We suggest printing non-toxic PLA lament when printer is used in children activity places. Q15. How to solve if printing result has edge warp?
Method1: Heating up the platform can solve or minimize the problem by increasing adhesion between platform and model. Method2: Adding raft to model when slicing in FlashPrint. Method3: Apply the solid glue to platform before printing. Q16. Is it a must to add a raft before printing the model?
Not necessarily, much more lament will come out of extruder when printing the raft, increasing printing success. Heating up the platform also increases printing success by increasing adhesion between platform and model. Q17. After replacing nozzle completed, printer status displays extruder temperature is 300, extruder fan is also working, what is the problem and how to solve it?
The new nozzle is not properly installed, extruder temperature can not be read and the displayed extruder temperature is abnormal. Please plug out and install the nozzle again, push nozzle to the end, make sure the nozzle slot and bottom of extruder are on the same level. Q18. The extruder makes out chug noise and no lament come out of extruder, what is the problem and how to solve ?
Filament has not loaded into extruder, making out chug noise,more likely the nozzle is clogged or lament guide tube is not properly installed. Check the guide tube joint rst, if the guide tube is normal, refer to Q1 for resolution. Q19. What is the dierence between lament load and lament replace ?
Load: Only include loading lament into extruder;
Replace: Include loading and unloading two functions, rst unloading and then loading lament. Q20. Adventurer 3 Pro 2 starts printing when the distance between extruder and build plate is still large,causing lament can not stick to build plate and print fails. Do the printer Calibration again or do the Homing again, then print again to check result. Q21. You cannot nd printing les when you use USB driver. USB driver le is not corrected. Adventurer 3 Pro 2 only supports FAT32 le system, please format USB driver into FAT32 le system. Daily Maintenance Instruction:
Please apply lubricate grease to printer guide rods if you do not use it for long,or do the same maintenance once a month. 48 Chapter 4: Supports and Service FlashForge team is on standby and ready to help you with any challenges you may have with your Adventurer 3 Pro 2. If the issues or questions are not covered in this User Guide, you can seek for solutions on our ocial website or contact us via telephone. There are solutions and instructions to common issues that can be found in our knowledge base. Have a look rst as most basic questions are answered there. www.FlashForge.com The FlashForge support team can be reached by e-mail or phone between the working hours from 8:00 a.m. to 5:00 p.m. PST Monday through Saturday. In case you contact us during o-duty time, your inquiry will be answered the following business day. Note: Because of changing dierent lament the extruder maybe clogged. Its not owing to quality issue, and outside the scope of 400 hours life. If users encounter this problem, please contact our after-sale department and nish clean work according to their instruction. Tel: +86 579 8227 3989 Email: support@3dp.com aftersales@ashforge.com ADD: No. 518, Xianyuan Road, Jinhua, Zhejiang, China. When contacting support, please have your serial number ready. The serial number is a bar code on the back of your Adventurer 3 Pro 2. 49 Follow us Zhejiang Flashforge 3D Technology Co., Ltd. Address: No.518 XianYuan Road, Jinhua City, Zhejiang Province, China Service Hotline: +86 579 82273989 support@ashforge.com
1 | Internal photos | Internal Photos | 1008.78 KiB | May 23 2023 / November 16 2023 | delayed release |
1 | ID label and location | ID Label/Location Info | 83.14 KiB | May 23 2023 |
FCC ID LABELING AND LOCATION FCC ID Label 3D Printer FCC ID: 2AKLL-ADVENTURER3P2 FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)
1 | Attestation Statements | Attestation Statements | 92.27 KiB | May 23 2023 |
C5266091_X24_Ed.2 Attestation Statements TO:
Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Zhejiang Flashforge 3D Technology CO., Ltd. Product Description: 3D Printer Grantee code: 2AKLL FCC ID: 2AKLL-ADVENTURER3P2 Contact Name: Qian Wang Address: No. 518, Xianyuan Road,Jinhua, Zhejiang, China Telephone No:0571-89774128 Email: wq@sz3dp.com i. ii.
[Zhejiang Flashforge 3D Technology CO., Ltd.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification.
[Zhejiang Flashforge 3D Technology CO., Ltd.] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification.
[Zhejiang Flashforge 3D Technology CO., Ltd.] (the applicant) certifies that, as of the date of the filing of the application, the applicant [ is not] identified on the Covered List as an entity producing covered equipment . Date: 2023/05/19 Applicants Name: Zhejiang Flashforge 3D Technology CO., Ltd. Title: Manager Signature 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1
1 | Confidentiality | Cover Letter(s) | 129.73 KiB | May 23 2023 |
Zhejiang Flashforge 3D Technology CO., Ltd. C5266091_X10_Ed.2 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AKLL-ADVENTURER3P2 To Whom It May Concern, Date: 2023-05-17 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules
(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No NOTE 1 NOTE 1 No No Short-Term Confidentiality NOTE 2 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ____180__ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:
Name: Qian Wang Title: Manager 1/1
1 | Letter Authorization | Cover Letter(s) | 44.94 KiB | May 23 2023 |
C5266091_X8_Ed.1 Letter of Authorization
<Zhejiang Flashforge 3D Technology CO., Ltd.>
Company: Zhejiang Flashforge 3D Technology CO., Ltd. Address: No. 518, Xianyuan Road,Jinhua, Zhejiang, China Product Name: 3D Printer Model Number: Adventurer 3 Pro 2 FCC Identifier: 2AKLL-ADVENTURER3P2 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Qian Wang Date: 2023-05-17 Title: manager Signature of applicant:
1/1
1 | US Agent Letter | Attestation Statements | 102.91 KiB | May 23 2023 |
US Agent for Service of Process LETTER OF ATTESTATION TO:
Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process:
Company Name: SUN BEYOND CONSULTING LTDOFFICE FRN: 0033588823 Contact Name: Peter Zhang Address: 90 CANAL STREET, 4TH FLOOR OFFICE NO.448 Telephone: +15084700660 Email: mrsunbeyond@gmail.com Applicant:
Company name: Zhejiang Flashforge 3D Technology CO., Ltd. Product Description: 3D Printer Grantee code: 2AKLL FCC ID: 2AKLL-ADVENTURER3P2 Contact Name: Qian Wang Address: No. 518, Xianyuan Road,Jinhua, Zhejiang, China Telephone No:0571-89774128 Email: wq@sz3dp.com
[Zhejiang Flashforge 3D Technology CO., Ltd.] certifies that, as of the date of this filing of the application with the TCB, [SUN BEYOND CONSULTING LTDOFFICE] is our designated US agent for service of process for the above referenced FCC ID. [Zhejiang Flashforge 3D Technology CO., Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [SUN BEYOND CONSULTING LTDOFFICE]
accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. Date: 2023/05/19 Applicants Name: Zhejiang Flashforge 3D Technology CO., Ltd. Title: manager Signature US Agent for Service of Processs Name:
SUN BEYOND CONSULTING LTDOFFICE Title: CEO Signature 1/1
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2023-05-23 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2023-05-23
|
||||
1 | Applicant's complete, legal business name |
Zhejiang Flashforge 3D Technology CO., Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0026099036
|
||||
1 | Physical Address |
No. 518, Xianyuan Road
|
||||
1 |
Jinhua, Zhejiang, N/A
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
e******@applus.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
2AKLL
|
||||
1 | Equipment Product Code |
ADVENTURER3P2
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
Q******** W******
|
||||
1 | Title |
Machinists Helper
|
||||
1 | Telephone Number |
0571-********
|
||||
1 | Fax Number |
N/A********
|
||||
1 |
w******@sz3dp.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Shenzhen CTA Testing Technology Co., Ltd.
|
||||
1 | Name |
E**** W****
|
||||
1 | Physical Address |
Shenzhen
|
||||
1 |
China
|
|||||
1 | Telephone Number |
86 75********
|
||||
1 |
w******@cta-test.cn
|
|||||
app s | Non Technical Contact | |||||
1 | Firm Name |
Shenzhen CTA Testing Technology Co., Ltd.
|
||||
1 | Name |
E******** W********
|
||||
1 | Physical Address |
Shenzhen
|
||||
1 |
China
|
|||||
1 | Telephone Number |
86 75********
|
||||
1 |
w******@cta-test.cn
|
|||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 11/16/2023 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 3D Printer | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power listed is conducted. This device supports 20 and 40 MHz bandwidth mode. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
SHENZHEN CTA TESTING TECHNOLOGY CO., LTD.
|
||||
1 | Name |
E**** W********
|
||||
1 | Telephone Number |
+86 7********
|
||||
1 |
w******@cta-test.cn
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.0239000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC