User Manual for WF-M63B-USH1 1. Introduction WF-M63B-USH1 module design is based on Mediatek MT7663BUN solution, The MT7663BUN is a highly integrated single chip which has built in a 2x2 dual-band wireless LAN radio and Bluetooth radio. It includes Bluetooth EDR and LE radio which complies with Bluetooth v2.1+EDR, v4.2, and v5.1. The Module is a highly integrated MAC/BBP and 2.4/5GHz PA/LNA single chip which supports a 866.7Mbps PHY rate. The Module is designed to support standard-based features in the areas of security, quality of service, and international regulations, giving end users the greatest performance anytime and in any circumstance. This documentation describes the engineering requirements specification. 1.1 RF module Overview The general HW architecture for the module is shown in Figure 1. This WLAN Module design is based on Mediatek MT7663BUN. It is a highly integrated single-chip MIMO(Multiple In Multiple Out) Wireless LAN (WLAN) network interface controller complying with the 802.11 specification and Bluetooth over USB interface. It combines a MAC, a 2T2R capable baseband, and RF in a single chip. An intelligent Wi-Fi/Bluetooth coexistence algorithm is implemented to provide the best harmonized Wi-Fi and Bluetooth radio performance. Figure 1 WF-M63B-USH1 Block Diagram 1.2 Specification reference This specification is based on additional references listed below. _ IEEE Std. 802.11a _ IEEE Std. 802.11b _ IEEE Std. 802.11g _ IEEE Std. 802.11n _ IEEE Std. 802.11ac _ Bluetooth 2.1+EDR/4.2/5.1 WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 1.3 System Functions Table1: General Specification as below:
Main Chipset Operating Frequency WiFi Standard Bluetooth Modulation Mediatek MT7663BUN 2.4G/5G 802.11a/b/g/n/ac (2x2) 2.1+EDR/4.2/5.1 WIFI:11b: DBPSK, DQPSK and CCK and DSSS 11a/g: BPSK, QPSK, 16QAM, 64QAM and OFDM 11n: BPSK, QPSK, 16QAM, 64QAM and OFDM 11ac: BPSK, QPSK, 16QAM, 64QAM,256QAM and OFDM Bluetooth: GFSK, /4-DQPSK and 8-DPSK Data rates Form factor Host Interface PCB Stack Dimension Antenna Operation Temperature Storage Temperature Operation Voltage Power ConsumptionWIFI TX Power ConsumptionWIFI RX Power ConsumptionBT TX Power ConsumptionBT RX 11b: 1, 2, 5.5 and 11Mbps 11a/g: 6, 9, 12, 18, 24, 36, 48 and 54 Mbps 11n: MCS0~15, up to 300Mbps 11ac: MCS0~9, Nss=2, up to 866.7Mbps 32pins USB 2.0 4-layers design Typical: 18mm x 27mm x 2.4mm external Antennas Design
-10 to +70
-40 to +85 3.3V +/-5%
813mA@3.3V 5G TX NSS=2 HT20 MCS0 165mA@3.3V 5G RX NSS=2 VHT80 MCS9 82mA@3.3V 29mA@3.3V WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 2. Mechanical Specification 2.1 Mechanical Outline Drawing Typical Dimension (W x L x H): 27.0mmx18.00mm x 2.4mm General tolerance: 0. 2mm TOP View SIDE View BOT View 2.2 Product Picture Top view Bot view WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 2.3 Pin define NO 1 2 3 4 5 6 7 8 Definition GND WIFI1 GND GND WIFI0 GND GND GND 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 WOW RST RST GND 3.3V NC GND NC NC NC NC GND DP+
DM-
GND NC GPIO3 GND BT RF GND NC NC NC Descriptions Ground WIFI1 Ground Ground WIFI0 Ground Ground Ground Wi-Fi device wake up host Internal regulator on/off Internal regulator on/off Ground
+3.3V Voltage power NC Ground NC NC NC NC Ground USB interface USB interface Ground NC Debug UART TXD Ground BT RF PIN Ground NC NC NC BT_Wake_host BT device wake up host WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 3. Electrical Specification This Specification is based-on conductive DVT testing result. The extreme condition include overall temperature (0,+25,+40) and overall voltage (2.97V,3.3V,3.63V). 3.1 IEEE 802.11b Section:
Items Specification Mode Channel Data rate TX Characteristics 1. Spectrum Mask @ Target Power 1) fc +/-11MHz to +/-22MHz 2) fc > +/-22MHz 2. Constellation Error(EVM) @ Target Power 1) 1Mbps 2) 2Mbps 3) 5.5Mbps 4) 11Mbps 3. Frequency Error RX Characteristics 4. Minimum Input Level Sensitivity(each chain) 1) 1Mbps (FER 8%) 2) 2Mbps (FER 8%) 3) 5.5Mbps (FER 8%) 4) 11Mbps (FER 8%) 5. Maximum Input Level (FER 8%) Contents IEEE802.11b DBPSK, DQPSK and CCK and DSSS CH1 to CH11 1, 2, 5.5, 11Mbps Max. Typ. Unit Remark Min.
-10 Min.
-10
-23
-23
Typ.
-95
-89 10
-30
-50
-13
-13
-13
-13 10 Max.
-85
-83
-81
-79
dBr dBr dB dB dB dB ppm Unit dBm dBm dBm dBm dBm WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 Contents IEEE802.11g & IEEE802.11a BPSK, QPSK, 16QAM, 64QAM and OFDM CH1 to CH11 @ 11g CH36 to CH48, CH149 to CH165 @ 11a Min. 6, 9, 12, 18, 24, 36, 48, 54Mbps Max. Typ. Unit Remark 3. 2 IEEE 802.11g/a Section:
Items Specification Mode Channel Data rate TX Characteristics 1. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 2. Constellation Error(EVM) @ Target Power 1) 6Mbps 2) 9Mbps 3) 12Mbps 4) 18Mbps 5) 24Mbps 6) 36Mbps 7) 48Mbps 8) 54Mbps 3. Frequency Error 1) IEEE802.11g 2) IEEE802.11a 4. Minimum Input Level Sensitivity(each chain) 1) 6Mbps (PER 10%) 2) 9Mbps (PER 10%) 3) 12Mbps (PER 10%) 4) 18Mbps (PER 10%) 5) 24Mbps (PER 10%) 6) 36Mbps (PER 10%) 7) 48Mbps (PER 10%) 8) 54Mbps (PER 10%) 5. Maximum Input Level (PER 10%) 1) IEEE802.11g 2) IEEE802.11a
-20
-30
-10
-10 Min.
-30
-37
-94
-76
-2
-2
-20
-28
-40
-8
-11
-13
-16
-19
-23
-25
-28
-85
-84
-82
-80
-77
-73
-69
-68
10 10 Max. dBr dBr dBr dB dB dB dB dB dB dB dB ppm ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm RX Characteristics Typ. WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 TX Characteristics Min. Remark 3.3 IEEE 802.11n HT20 Section:
Items Specification Mode Channel Data rate (MCS index) 1. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 2. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 3. Frequency Error 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G RX Characteristics 4. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 5. Maximum Input Level (PER 10%) 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G Contents IEEE802.11n HT20 @ 2.4G IEEE802.11n HT20 @ 5G BPSK, QPSK, 16QAM, 64QAM and OFDM CH1 to CH11 @ 2.4G CH36 to CH48, CH149 to CH165 @ 5G MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 Max. Typ. Unit
-20
-30
-10
-10 Min.
-30
-38
Typ.
-94
-74
-2
-2
-20
-28
-45
-8
-13
-16
-19
-22
-25
-28
-30
-85
-82
-80
-77
-73
-69
-68
-67
10 10 Max. dBr dBr dBr dB dB dB dB dB dB dB dB ppm ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 3.4 IEEE 802.11n HT40 Section:
Items Specification Mode Channel Data rate (MCS index) TX Characteristics 1. Spectrum Mask @ Target Power 1) at fc +/-21MHz 2) at fc +/-40MHz 3) at fc > +/-60MHz 2. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 3. Frequency Error 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G RX Characteristics 4. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 5. Maximum Input Level(PER 10%) 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G Contents IEEE802.11n HT40 @ 2.4G IEEE802.11n HT40 @ 5G BPSK, QPSK, 16QAM, 64QAM and OFDM CH3 to CH9 @ 2.4G CH38 to CH46, CH151 to CH159 @ 5G MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 Max. Typ. Unit Min. Remark
-20
-30
-30
-38
-90
-71
-2
-2
-20
-28
-45
-8
-13
-16
-19
-22
-25
-28
-30
-82
-79
-77
-74
-70
-66
-65
-64
dBr dBr dBr dB dB dB dB dB dB dB dB ppm ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm
-10
-10 Min.
Typ. 10 10 Max. WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 Contents IEEE802.11ac BPSK, QPSK, 16QAM, 64QAM ,256QAM and OFDM CH36 to CH48, CH149 to CH165 VHT20 CH38 to CH46, CH151 to CH159 VHT40 CH42, CH155 VHT80 MCS0/1/2/3/4/5/6/7/8/9 TX Characteristics Min. Typ. Max. Unit Remark 3.5 IEEE 802.11ac Section:
Items Specification Mode Channel Data rate (MCS index) 1. Spectrum Mask @ Target Power 1) at fc +/-11MHz /20MHz/30MHz 2) at fc +/-21MHz /40MHz/60MHz 3) at fc +/-41MHz /80MHz/120MHz 2. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 9) MCS8 10) MCS9 3. Frequency Error RX Characteristics 4. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 9) MCS8 (PER 10%) 10) MCS9 (PER 10%) 5. Maximum Input Level(PER 10%)
-10 Min.
-30 VHT 20
-94
-70
-2
-36
Typ. VHT 40
-90
-65
-2
-20
-28
-40
-8
-13
-16
-19
-22
-25
-28
-30
-32
-33 10 Max. VHT 40
-82
-79
-77
-74
-70
-67
-65
-64
-59
-57 dBr dBr dBr dB dB dB dB dB dB dB dB dB dB ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm VHT 80
-87
-63
-2 VHT 20
-85
-82
-80
-77
-73
-69
-68
-67
-62
-60
VHT 80
-79
-76
-74
-71
-67
-63
-62
-61
-56
-54 WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 3.6 Bluetooth Section:
3.6.1 BR Specification Items Host Interface Channel Modulation TX Characteristics 1.Modulation Characteristics 1)Delta f1(Avg) 2)Delta f2max(For at least 99.9% of all Delta f2max) 3)Delta f2/ Delta f1 2.Initial Carrier Frequency Tolerance 3. Carrier Frequency Drift 1) One Slot packet drift (DH1) 2) Three Slot packet drift (DH3) 3) Five Slot packet drift (DH5) 4) Max Drift Rate RX Characteristics 1. Receiver Sensitivity (BER<0.1%) 2. Maximum usable signal (BER<0.1%) USB Min. Typ. Contents CH0 to CH78 GFSK Max. Unit kHz kHz kHz kHz kHz kHz kHz kHz/50us dBm dBm
157 121 0.85
+/-20
+/-15
+/-15
+/-15
+/-15
-94
-5 WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 3.6.2 EDR Specification Items Host Interface Channel Modulation TX Characteristics 1. Frequency Stability 1) Omega-i 2) Omega-0 3) Omega-0 + Omega-i 2. Modulation Accuracy 1) RMS DEVM
/4-DQPSK 8PSK 2) Peak DEVM
/4-DQPSK 8PSK 3) 99% DEVM
/4-DQPSK 8PSK RX Characteristics 1. Receiver Sensitivity (BER<0.01%) 1) /4-DQPSK 2) 8PSK 2. Maximum usable signal (BER<0.1%) 1) /4-DQPSK 2) 8PSK USB Min. 6 Contents CH0 to CH78
/4-DQPSK 8PSK Max. 14
Typ. 10
+/-4
+/-4
+/-4
+/-9
+/-9
+/-28
+/-21
+/-15
+/-12
-91
-89
-5
-5 Unit kHz kHz kHz
dBm dBm dBm dBm WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 3.6.3 LE Specification Items Host Interface Channel TX Characteristics 1. Modulation Characteristics 1)Delta f1(Avg) 2)Delta f2max(For at least 99.9% of all Delta f2max) 3)Delta f2/ Delta f1 2. Carrier frequency offset and drift 1) Frequency Offset 2) Frequency Drift 3) Max Drift Rate 3.In-band Spurious Emissions 1)+/-2M offset 2)>+/-3MHz offset RX Characteristics 1. Receiver Sensitivity (BER<30.8%) 2. Maximum usable signal (BER<30.8%) Contents USB Min. Typ. CH0 to CH39 Max. Unit 225 185 0.8
-150
-50
-20 275 150 50 20
-20
-30 kHz kHz Hz/Hz kHz kHz Hz/us dBm dBm dBm dBm 0.94
-95
-5 WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 4. Reference Design 4.1 SCH 4.2 Recommend PCB Layout Decal WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 5. Host Interface Timing Diagram 5.1 Chip power on sequence 5.1 reset sequence 6. Software Requirements The driver supports the following operating systems: Linux, Microsoft Windows XP, Vista and Win7. Mfg. software tool is MT7663BUN_QA_Tool. WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 7. Antenna Information 0.29dBi WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1 8. DC Characteristics Input Low Voltage Symbol Parameter DVDDIO 3.3V IO Voltage VIL VIH VOL VOH Input High Voltage Output Low Voltage Output High Voltage Min 2.97
-0.3 VDD33*0.625
-0.3 VDD33-0.4 Type Max 3.3
0.4 3.63 VDD33*0.25 VDD33+0.3 VDD33+0.3 Unit V V V V V FCC Statement:
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)
(2) undesired operation. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
(1) Operational use conditions Module has professional users use condition limitations, Host product manufacturer please ensure giving such warning like Product is limited to professional users use in your products instruction.
(2) Antenna used Antenna type BT/BLE PCB Antenna 2.4G Wi-Fi PCB Antenna Max. Antenna Gain 0.37dBi Antenna 1: 0.06dBi Antenna 2: 2.65dBi Antenna 1:
U-NII-1: 0.29dBi U-NII-3: -1.16dBi Antenna 2:
U-NII-1: 0.12dBi U-NII-3: 0.99dBi 5G Wi-Fi PCB Antenna
(3) Labelling Instruction for Host Product Integrator Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. For FCC, this exterior label should follow Contains FCC ID:
2AL8S-0302C3XN-1. In accordance with FCC KDB guidance 784748 Labeling Guidelines. 15.19 and RSS-Gen Labelling requirements shall be complied on end user device. Labelling rules for special device, please refer to 2.925, 15.19 (a)(5) and relevant KDB publications. For E-label, please refer to 2.935. WF-M63B-USH1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/4.2/5.1
(4) Installation Notice to Host Product Manufacturer The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. The module is limited to installation in mobile application, a separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and difference antenna configurations.
(5) Antenna Change Notice to Host manufacturer If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through the change in FCC ID and IC ID (new application) procedure followed by a Class II permissive change application.
(6) FCC other Parts, Part 15B Compliance Requirements for Host product manufacturer This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer in any case shall ensure host product which is installed and operating with the module is in compliant with Part 15B requirements. Please note that For a Class B or Class A digital device or peripheral, the instructions furnished the user manual of the end-user product shall include statement set out in 15.105 Information to the user or such similar statement and place it in a prominent location in the text of host product manual. Original texts as following:
For Class B Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. For Class A Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.