BTR011 Bluetooth audio receiver Users manual Content
Brief introduction......1 1. Bluetooth wireless communication technology.1 2. About BTR011..1
Basic operation.......1 1. Overview......1 2. The steps of operation..2 3. Paired with Bluetooth device...2 1) How to enter paired mode....2 2) Pairing with Bluetooth phone..2 3) Pairing with Bluetooth transmitter.....3 4. Supply power for other device charging3 5. LED indicator...4
Care and maintenance....4
FAQs.....5
Specifications.5 Welcome to use this Bluetooth audio receiver BTR011. Please read this users manual carefully before use.
Brief introduction 1. Bluetooth wireless communication technology Bluetooth is a standard of close range wireless communication technology that was drawn up by Ericsson, IBM, Intel, Nokia and Toshiba in May, 1998. With Bluetooth technology, we can achieve the highest transmission rate among cell phones, computers, printers, PDAs and other devices. The max transmission range of class II is 10 meters while the max transmission ranges of class I can reach up to 100 meters. 2. About BTR011 BTR011 is a stereo Bluetooth receiver with power pin, it has following features:
Enjoy stereo music wireless with device which support Bluetooth A2DP profile;
It can supply DC5V-1A to other device for charging.
Basic operation 1. Overview 1 1 2 3 4 USB charging jack Power pin Status indicator light 3.5mm audio line-out jack audio line 2. The steps of operation
The receiver will turned on automatically when plug it into standard AC socket, and it will enter pairing mode
Paired with Bluetooth phone or Bluetooth transmitter
Connected receiver and external audio device through 3.5 to 3.5mm
It can transfer music from phone or transmitter to external audio device 3. Paired with Bluetooth device 1) How to enter pairing mode Function pairing Entering mode Operation After turned on, it will enter pairing mode automatically LED indicator Blue LED continuously flash Remarks:
The pairing mode will last 2 minutes, BTR011 will switch to standby mode automatically, if no devices can be connected after 2 minutes 2) Pairing with Bluetooth phone Prior to using the receiver for the first time, you have to pair it with a Bluetooth phone. Please make sure your phone has Bluetooth function and it is available. The pairing procedures are subject to different models of cell phones. Please refer to your cell phone users manual for further information. The general pairing procedures are as follows:
Keep your receiver and phone within 1 meter when pairing;
Make the receiver enter pairing mode(please refer to How to enter pairing mode)
Activate your cell phones Bluetooth function and set your cell phone to search for Bluetooth devices within range, and select BTR011 from the list of devices shown;
According to the indication, enter password or PIN No: 0000, and press YES or Confirm;
2
If prompted by your cell phone to connect, select Yes (this will vary among cell phone models). After successful connecting, blue LED will flash twice every 4 seconds. Remarks:
The receiver can remember 8 paired devices. When the number of devices exceeds 8, the first one will be replaced.
If the phone and receiver over range, the receiver will disconnect and enter standby mode. It will connect automatically if phone and receiver back to available range in 5 minutes. You also can select BTR011 on the phone after 5 minutes. 3) Pairing with Bluetooth transmitter You can pair receiver with Bluetooth transmitter to enjoy wirelessly music. Hereby take BTT001 (Bluetooth transmitter for iPod, not included) for example. The pairing steps are as follows:
Keep the Bluetooth transmitter and the receiver within 1 meter when
Make the receiver enter pairing mode (please refer to How to enter pairing;
pairing mode);
Plug the Bluetooth transmitter into cell phone and activate it. The transmitter will search device automatically and start pairing;
When the receiver requests PIN No., the Bluetooth transmitter will
After successful pairing and connecting, blue LED of the receiver blinks respond 0000 automatically;
twice every 4 seconds. Note:
The pairing password of the receiver is 0000. So, the receiver can only pair with a Bluetooth transmitter whose pairing password is 0000.
If pairing still fails after several tries, please refer to the Bluetooth transmitters users manual for further information. 4. Supply power for other device charging The USB port of receiver can provide DC5V-1A for other device charging. You also can charge your device by BTR011 through USB cable. 3 Remarks:
Please use standard USB cable which compatible with your device
The USB port can only provide DC5V-1A, please make sure the charging voltage of your device is DC5V and the max charging current no higher than 1A 5. LED indicator Status of receiver Pairing mode Standby mode(not connect device) LED indicator Blue LED flash continuously Blue LED flash once every 2 seconds Blue LED flash twice every four seconds Standby mode(has already connected device)
Care and maintenance Read the following recommendations carefully before using BTR011. Following these you will be able to enjoy this product for many years.
Keep it dry and dont put it in moist place to avoid the products internal circuit being affected.
Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery or distort certain plastic parts.
Dont expose the product to cold areas. It may damage the internal circuit
Dont try to disassemble the product as it may get damaged if you are not board. professional.
Dont let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged.
Dont use intensive chemical products or detergent to clean the product.
Dont scratch the surface with sharp things. In case the product doesnt function properly, send it to the store you bought it. The staff will help you to solve the problem 4
FAQs 1. Why the receiver can not paired with phone?
Please make sure the receiver is in pairing mode.
The pairing mode will last 2 minutes, it will enter standby mode automatically if overtime.
Disconnect the receiver and socket, and reconnect them, after the receiver turned on, it will enter pairing mode automatically. 1A MAX 2. Why it can not connect with phone automatically after over range and come back?
If it over range, you should come back in 5 minutes, and them the receiver will connect with phone automatically. If over 5 minutes, you can connect it by operate your phone.
Specifications Bluetooth version Bluetooth profiles Operating distance Power supply demand USB output Dimension Weight ambient temperature Bluetooth V2.1+EDR A2DP Up to 10meters AC100~240V DC 5V 38.5*38.5*67.5mm About 43.8g 40 MAX Warning: Changes or modifications to this unit not expressly approved by the Party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
_ Reorient or relocate the receiving antenna. _ Increase the separation between the equipment and receiver. _ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. _ Consult the dealer or an experienced radio/TV technician for help. Notes:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The main plug is used as disconnect device, the socket-outlet should be near the product and it should be easily accessible. 5