FCC ID: WADBTH180P Bluetooth True Wireless Headset

BTH80P True Wireless Bluetooth Headset Users manual Contents Brief introduction........ 1 Before use. 1 1. Overview...1 2. Charging for headset..2 2. Charging for charging case..2 Getting started..3 1. Wearing headset.............................................................3 2. Mono & Twin Modes.............................................................5 3. Earbuds pairing/connecting........................................................6 4. Function operation.........................................................8 7. Battery display........................................................................ .....8 8. Meaning of indicator light.....9 9. Factory Reset.....9 Care and maintenance...10 FAQs.....11 Specification.....11 Welcome to use this True Wireless Bluetooth headset, BTH180P, Please read this users manual carefully before use. Brief introduction BTH180P is a true wireless Bluetooth headset. The earphones on the left and right sides adopt a separate design, which can be used in different occasions according to personal usage habits. There is no need to connect the earphone cable between the two earphones. It can be used with a single earphone or can realize stereo effect through Bluetooth connection. The headset is equipped with a dedicated charging box, which is convenient to carry and charge the headset, and the charging box itself supports wireless charging. You can use your wireless charger to charge the charging box. Before use 1. Overview 1 MFB touch-button 6 Type-C charging jack 2 LED indicator (Red and blue) 3 Microphone Top case area Earhook Charging pins 7 Wireless charge induction Charging indicator light 4 5 2. Charging for earbuds When the headset is low on power, it emits the red light flashing slowly 4 times every 14s. Please recharge the battery of the headset. The way of charging for the earbuds as following:

1. Put the earbuds into the charging case to ensure that the charging pins connect well, and start charging when you see the red indicator light of the earbuds on. (If the cover of the charging box is closed, the charging will be disconnected when opened, you need to take out the earphones and put them back in order to continue charging) Red light on: Charging Red light off: Finished charging 8 9 2. Charging should be completed in roughly 2 hours. Remarks:

Please place the L and R earphones in the correct charging compartment according to the L and R marks on the charging box to charge them. 3. Charging for charging case When any of the following situations occurs, it indicates that the charging case will be low power. You need to charge the charging case:

1) When the indicator of the charging case has only one white light on, it means the battery of the charging case is low. 2) When the indicator light of the charging case doesnt turn on and the earphone cannot be charged, it means that the battery of the charging case has been used up The charging case supports USB cable charging and wireless charging. The way of charging for the charging case as following:

Using USB cable 1) Plug the Micro USB charging cable into the cases charging jack. 2) Plug the USB cable into a USB port of PC or a 5Volt USB charge. Wireless charging 1) Connect the wireless charger to the power cable. (some wireless chargers with built-in batteries may not need to be connected to the power cable) 2) Place the charging case in the charging area marked on the wireless charger and make sure it is placed in the center of the charging area for maximum efficiency. Charging box battery indicator flashes = charging White LED off = Finished charging 3) Charging should be completed in roughly 2.5 hours.When using wireless charging , the charging time will be slightly longer. 4) If the earbuds are in the charging case, it can charge the earbuds while charging the charging case. Type-C charging Wireless charging Remarks:

The indicator light of the charging box is off when the earphone in the idle statenot in charged. Open the cover of the charging box, the 4 white indicator lights of the charging box will light up in sequence, and the indicator lights will go out after about 5s. Indicates that the current charging box power level from low to high is one, two, three, and four white lights flashing. If you do not use the earbuds and charging case for a long time, it is recommended to charge the earbuds and charging case for at least 3 months to avoid the battery exhaustion and enter the sleep mode. Notes:

Batteries (battery pack or batteries installed) shall not be exposed to excessive heat place, such as sunshine, fire. The battery is recyclable. Getting started 1. Wearing headset with earhook a. Choose the right earphone to match the ear b. Align the earphone with the ear and insert the ear tip into the ear hole C.Rotate the earphone to a comfortable position 2. Without earhook a. Choose the right earphone to match the ear b. Align the earphone with the ear and insert the ear tip into the ear hole C.Rotate the earphone to a comfortable position 3.Mono mode Each earbuds can be connected singly to the cellphone. 1. Power on 1)In the charging state, open the charging box top case or take the earphone out of the charging box, and the earphone will automatically turn on. 2)If the earbuds are power off, you should press touch-button for about 3s until blue LED flashes as the same time the earbuds emits Power on. Then release. This is now in the Power onstate. 2.Pairing 1) When we open the charging case, it will be power on and turn into pairing mode. Then it will connect back to the phone you paired with before.When the earbuds and the cellphone fails to connect back, the earbuds will automatically enter the pairing state. 2) If the earbuds are power off, you should press touch-button for about 5s and release it when the red LED and blue LED flash quickly and alternately. You will hear Pairing. The earbuds are in Pairingmode 3.Connecting When the headset is in pairing mode, search for the corresponding Bluetooth phone name from the Bluetooth list of the phone and click Connect (some phones do not have a connection pop-up window). After the pairing and connection are successful, both ears will simultaneously display

"Connected". 4.Power off 1Auto power off once put into charging case 2Press touch-button about 5s and release it till red LED is on,and earbuds prompt Power off. Remark:

When the earbuds are idle and not connected to the Bluetooth device, they will automatically enter the pairing mode after 10 seconds. The pairing mode will last for 5 minutes. If it is not paired with any mobile phone after 5 minutes, the earbuds will shut down automatically. 5. Twin mode

(Binaural mode: connect left and right earphones to enjoy stereo sound) 1. Connection method: Operate any earphone to enter the pairing mode and pair with the mobile phone, then turn on the other earphone or take it out of the charging box. If you click pair, the secondary earbud will also be paired with the phone., the two earphones can be automatically connected. 2. Role switching: If the headset is successfully paired with the mobile phone, the role switching function can be performed. In the following cases, the accessory ear can automatically switch and connect to the mobile phone so that you can continue to use the headset:

1) When the main earphone is automatically turned off during low power during use, the auxiliary earphone can be automatically connected to the phone. 2) When the main earphone is put into the charging box for charging, the auxiliary earphone can be automatically connected to the mobile phone. 6.Pair and connect the left and right earphones (when the two earphones cannot be connected automatically) 1. Put the left and right earphones into pairing state respectively (red and blue lights flash alternately). 2. When the headset is in the pairing state, press the touch button in 5 consecutive taps, and see that the red light turns to red and blue lights alternately and slowly flashing after 1 second, which means the headset has entered TWS pairing mode. 3. After the two earphones enter TWS pairing mode (red and blue lights alternately flash slowly), the earphones will automatically match and connect successfully. Remark:

1. The left and right earphones have been matched and connected before leaving the factory. Normally, you only need to take the left and right earphones out of the charging box to automatically power on and connect. 2. If two earphones cannot be automatically connected after being taken out of the charging box at the same time, you can press this operation to re-establish the connection between the left and right earphones. 6.Function operation 1. music Function Status of earbuds Play Pause Previous song Next song Deep base Playing music Playing music Playing music Playing music Playing music L R Double-click touch-button Double-click touch-button Press Left touch -

button about 2s Double-click touch-button Double-click touch-button N/A Prompt tone N/A N/A Dang N/A N/A Press Right touch -

button about 2s triple-click touch-button Right Dang Deep base Balance Playing music N/A triple--click Right touch-button Balance 2.Calling Function Cancel calling Answering Reject Status of earbuds Calling Incoming call ringing Incoming call ringing End calling During a call L R Prompt tone Dang Dang Dang Once-click touch-button Once-click touch-button Double-click touch-button Double-click touch-button Once-click touch-button Once-click touch-button Double-click touch-button Double-click touch-button Press

touch button about 2s After dang Falling tone to Voice switch phone Voice switch to earbuds During a call touch Press

button about 2s Falling tone During a call touch Press

button about 2s touch Press

button about 2s Rising tone 3. Connected mobile phone operation L and the Press hold touch bottom 4s N/A Function Status of earbuds Voice dialing Connected with phone Turn on ambient sound Connected with phone R Prompt tone N/A Voice dial Press and hold the touch bottom 4s Audio pass through on Turn off ambient sound Connected with phone N/A Press and hold the touch bottom 4s Audio pass through off Game mode Connected with phone triple--click touch-button N/A Exit Game mode Connected with phone triple--click touch-button N/A Volume up During a call N/A Short press touch-button Short press touch-butt on Volume down During a call N/A Enter gaming mode exit gaming mode There is no prompt sound during operation, and the maximum volume prompts Maximum There is no prompt sound during operation, and the maximum volume prompts Minimum Remark In the call mode, the left and right earphones have a call sound and can operate the call, but only the microphone of the main earphone can record the sound. 7.Battery display When the earbuds are connected to an IOS device or some of the Android device, it will display the battery of earbuds on the device. When the earbuds is low on power ,the battery indicator will turn red and show a depleted battery icon. For different phones, there may be different ways to display the battery life on the phone. The following is a screenshot of the battery life on the iOS phone. Pairing mode with phone flash State Earbuds Full charge Low battery 8. Meaning of indicator light indicator light Red and blue LED quickly alternately Red and blue LED slowly alternately Blue LED flashes every 5 seconds Blue LED flashes twice every 10 seconds Red LED flashes four times every 14 second No indicator light will light up in the charging case without charging the earbuds into the case The number of white LED Charging the earbuds Charging case TWS pairing mode Unconnected Low battery Connected Idle state putting flash or represents the current battery power of the charging case. According to the power level from low to high, there are 1, 2, 3 and 4 white LED on.After flashing, it lights for about 5s and then goes out During the charging process, the number of white lights on the charging box represents the current battery power of the charging box. According to the power level from low to high, the white lights flash 1, 2, 3, 4 The white light of the charging box goes out after charging is completed Charging Finish charging 9. Factory Reset Put the earphone into the charging box, press and hold the left and right ears for 10 seconds at the same time. Red and blue LED are on for 1 second at the same time Press touch - button about 10 s Remarks:

After factory reset, the paired list of earbuds and mobile phone will be deleted. But the paired list of primary earbud and secondary earbud will not be deleted. The earbuds will no longer automatically connect back to the phone after they are turned on, but the primary and secondary earbud will still automatically connect back to each other. After factory reset, when the earbuds take out of the charging case, it will automatically enter the pairing mode with the phone (red and blue lights alternately flash quickly), and you need to click on the phone to repair. Care and maintenance Read the following recommendations carefully before using BTH180P. Following these you will be able to enjoy this product for many years. Keep it dry and dont put it in the damp place to avoid the products internal circuit being affected. Dont wear the headset when in strong exercise to avoid sweat enter. Clean the earbuds before putting it into the charging case to prevent sweat from corroding the product. Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery or distort certain plastic parts. Dont expose the product to cold areas. It may damage the internal circuit board. professional. Dont try to disassemble the product as it may get damaged if you are not Dont let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged. Dont use intensive chemical products or detergent to clean the product. Dont scratch the surface with sharp things. In case the product doesnt function properly, send it to the store you bought it. The staff will help you to solve the problem FAQs 1. What does it mean when red LED flashes slowly four times a minute?

Battery is low power, need to be recharged. 2. Why is the red LED off when charging?

a) The charging case may not have enough power to charge the headset. Please charge the charging case. b) Make sure the metal contacts of the earbud and charging case are free of obstacles. a) The battery may dry up. Please charge the battery for 30 minutes, and then the red LED will be on. 3. Why cant I hear the sound on the headset?

a) Make sure the volume is not too low or muted;

b) Make sure the headset connects with the mobile phone correctly;

c) Make sure the distance between the headset and the cell phone is in the available Bluetooth range. 4. Why cant I hear the sound clearly on the headset?

a) Make sure the mobile phone is in the strong signal area;

b) Make sure the headset is in the available range. and no other block 5. Why the pause/play, last/next song not function when playing music?

Make sure your Bluetooth device supports AVRCP (Audio/Video Remote Control profile) Specifications Bluetooth version Bluetooth profiles Operating distance Working time(one earbud) Working time(two earbuds) Charging earbud Charging time for case cycle the count charging case to charge the earbuds Charging input for case time for of Weight Measure Bluetooth V5.0 HFP, HSP,A2DP and AVRCP 10 meters Up to 4.5 hours(maximum volume) Up to 6 hours (50% volume) Up to 4.5 hours (maximum volume) Up to 6 hours (50% volume) About 2 hours About 2.5 hours 3.5 times USB charging: DC5.0V 500mA with One earbud:9.0g Charging case:66.8g Earbud 32.8 x 49.3 x 26.0 mm Earbud 21.8 x 25.0 x 26.0 mm Charge case 87.0 x 57.4 x 34.8 mm ear hook:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Zhongshan K-mate General Electronics Co., Ltd Agent Authorization Company: Zhongshan K-mate General Electronics Co., Ltd Address: NO.2, 5th Xinsheng Street, Gangkou Town, Zhongshan, China Product Name: Bluetooth True Wireless Headset Model Number(s): BTH180P, TENNMAK SMARTPRO Product Description: Bluetooth True Wireless Headset We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

DecaiLiu Date: 2021-03-31 Company: Zhongshan K-mate General Electronics Co., Ltd.

Zhongshan K-mate General Electronics Co., Ltd Mar.31, 2021 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID : WADBTH180P Model Number: BTH180P, TENNMAK SMARTPRO To Whom It May Concern:

We, The Zhongshan K-mate General Electronics Co., Ltd. hereby declare that the model : TENNMAK SMARTPRO is identical with the model : BTH180P, except the model name. Except for the different above, no other modification is performed. Sincerely, Signature:

Zhongshan K-mate General Electronics Co., Ltd. Contact person: DecaiLiu

Zhongshan K-mate General Electronics Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021-03-12 Subject; Request for Confidentiality FCC ID: WADBTH180P To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market.

[><JSchematic Diagram XBlock Diagram

[_]Parts List

[>xJOperational Description

[_]Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

[_]External Photos

[_|Test Setup Photos

[_]Internal Photos

[_]User Manual

[_]For 45 days, pursuant to Public Notice DA 04-1705. OR

[_]For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely Zhongshan K-mate General Electronics Co., Ltd. Contact person: DecaiLiu