Product Introduction Quick Installation Guide Wireless N Range Extender Model No.: EX200 LAN port: This port is used to connect to PC. RST: Press the button for about 10 seconds, the device will restore to factory default settings. RST Copyrights TOTOLINK. All rights reserved. Website: http://www.totolink.net Information in this document is subject to change without prior notice. V1.1706 On: The device is starting up or waiting for extending. Slow-blinking: The device is working normally. Quick-flashing: The device is to restart. Off: The device is power off. WPS: Press the button for about 2-3 seconds to enable WPS. On: Extending successfully. Green-Good;Yellow-Normal;Red-Bad. Slow-blinking: The device is extending to upper Router/AP. Quick-flashing: The device is to restart. Off: No extending. Method One: Quick Setup by Smart Phone 1 Power on. Plug the device into any wall socket that near the router. Wait until the System LED blinks slowly. 2 Connect to the Extender. Using your smart phone to search Wi-Fi TOTOLINK_EX200. (SettingsWi-Fi) 3 Login. The Setting page will turn up automatically. Click Extender Mode. If below window doesnt appear, please open a browser and enter 192.168.0.254 manually. 4 Extend Wi-Fi. Wait for a while, the Extender auto-detects APs nearby. Choose your routers 2.4GHz SSID. 5 Configure. Enter its wireless password. Either keep the default SSID or customize it for extended 2.4GHz wireless network. Verify your settings and click Connect. 6 Verify. Check the LED status to verify whether the Wi-Fi extension is successful. Wi-Fi Extended successfully while the Extend LED indicator keeps lighting. Relocate 1 Plug the extender into wall socket that halfway between your router and the Wi-Fi dead zone. Wait about 30 seconds until the Extend LED light turns solid green or yellow. If not, please relocate it closer to your router to achieve better signal quality. Host Network Extended Network 2 In order to make full use of extender, please keep the antennas of the extender perpendicular to the horizontal plane. See blow:
Wall Socket Vertically place the Extender Horizon Line FCC warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. For more information, please go to www.totolink.net Method Two: Wi-Fi Extension by WPS Button 1 Power on. Plug the device into any wall socket that near the router. Wait until the System LED blinks slowly. 2 Press WPS button on your router for about 2 seconds. 3 Press WPS button on Extender for about 2 seconds.
/
R S T W P S SSID: TOTOLINK_EX200 The Extend LED flash when connecting and turns to solid light when connected FAQ(Frequently Asked Questions) 4 The Extend LED turns to solid light, Wi-Fi extension successful. Please refer to Relocate to place the Extender. 1 What should I do if I cannot access the extenders web management page?
A1: Make sure you have connected to the wireless network name of the extender. A2: Open any browser, enter 192.168.0.254 in the address bar and press Enter. A3: Reset the extender and connect to it again. 2 How to reset the extender to factory default settings?
Keep the extender power on, use a pin to press the RST button on the bottom of device. When both System and Extend LED blinks, release the button. The device will restore to factory default settings. Wi-Fi: Upper routers SSID and password EX200's default Network Name (SSID) is TOTOLINK_EX200 (no encryption). With success repeater connection, this SSID (TOTOLINK_EX200) will change to the same SSID (with same encryption) of upper Router/AP. After deployment, just connect to the Router/AP's SSID. Congratulations, you have extended your WiFi coverage successfully.