FCC ID: X7D-IP04338 AC1200 Dual Band Smart Home Wi-Fi System

1 Appearance Front Panel Quick Installation Guide AC1200 Dual Band Smart Home Wi-Fi System Model: T6 Copyright 2018 TOTOLINK. All Rights Reserved. Website: http://www.totolink.net Information in this document is subject to change without prior notice. T Button State LED

(Recessed) LAN Ports WAN Port DC Power Port LAN Ports DC Power Port LED Status Description Solid Green Blinking Green The router is booting. It takes about 40 second, and after that the LED color will become blinking Green. Satellite router is synced with Master router successfully. And the signal is good. Router finishes the booting and is working normally. Blinking between Red and Orange Solid Orange(Satellite Router) The sync is being processed between Master router and Satellite router. Satellite router is synced with the Master router successfully, but the signal is not very good. 2.1. Diagram of a Masters network Router (Master) Master Router Back Panel Blinking Red The reset process is being proceeded. Solid Red(Satellite Router) Satellite router failed to sync with the Master Router. Outlet Satellite Router Back Panel Button/Ports T Button LAN Ports WAN Port DC Power Port Description Reset the router to factory settings. Press and hold the T button for 8-10 seconds(LED will blink Red) to reset the router. Confirm the Master router and activate the Mesh. Press and hold the T button until LED blinks between Orange and Red(about 1-2 seconds) to activate the Mesh function on the Master router. Connect to PCs or Switches with RJ45 cable. Connect to the Modem or connect the Ethernet cable from ISP. Used as a LAN pot in the Bridge, Repeater, WISP operation mode, or on the Satellite router in the Mesh Wi-Fi system. Connect to the power source. Power adapter Internet Smartphone Tablet PC 2 Connect the Master router to the Internet Master router and Satellite router have been paired successfully as the factory default setting. (It doesnt need any configurations on the Satellite router.) Master router and Satellite router can be recognized from the label stuck on the bottom of the router. 2.2. Configure the Master router on Phone 1 Connect the Wi-Fi of the router with your Phone, then run any Web browser and enter http://itotolink.net

(Tips: 8196D1 and 8196C1 on the SSID represent the last 6 numbers/letters from the MAC address, here we take them as an example, they are different in any other routers.) 2 Input admin for both User Name and Password on the coming page, then click Login. http://itotolink.net admin admin TOTOLINK_8196D1 TOTOLINK_5G_8196C1 3 Click Quick Setup on the coming page. 4 Internet Setting. Choose a suitable WAN Connection type from the list, and fill in the information required. http://itotolink.net Model No: T6 3 Create the Seamless Mesh Wi-Fi System After configured the Master router, please relocate the satellite routers to a suitable place to finish the Mesh Wi-Fi system. One T6 master router supports to pair with max 4 satellite routers, but pairing with 1 or 2 satellite routers is the recommended solution. 3.1 Diagrams of the Mesh Wi-Fi system Mesh Wi-Fi System of 1 Master Router and 2 Satellite Routers Satellite Mesh Wi-Fi System of 1 Master Router and 1 Satellite Router Satellite Master WAN Connection Type Description Static IP DHCP PPPoE Input the IP address, Subnet Mask, Default Gateway, DNS from your ISP. No information required. Please confirm with your ISP if DHCP is supported. Input User Name and Password from your ISP. Satellite Master 3.2 Relocate the Satellite router Power on the Satellite routers within the wireless coverage of the Master router and adjust the positions of the Satellite routers to achieve the best signal according to the LED colors on the T button. Green color indicates the signal is good. Yellow color indicates the sig-

nal is not good enough, please close the Satellite router to the Master router until the color turns Green. Red color indicates the signal is bad or not successfully connected with the Master router, please close the Satellite router to the Master router until the color turns Green.(If it doesnt work, reset the router and try again. FAQs4 1. Unable to log in the router's web page on Phone?

Please check if your Phone has connected to the Wi-Fi of the router and make sure you have entered the correct default gateway http://itotolink.net 2. How to reset the router to factory default settings?

Keep the router powered on, then press and hold the RST button

(for about 5-8 seconds) until System indicator becomes blinking light quickly. 3. How to do if I want to add a new Satellite router to the existing Mesh Wi-Fi system?

Keep the Satellite router as the factory default setting(If uncertain, pl-

ease reset the router) and then power on the Satellite router within the wireless coverage of the Master router. It will pair with the existing Master router automatically. FCC warning:

This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radi-

ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communic-

ations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an un-

controlled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. users authority to operate the equipment. Manufacturer: ZIONCOM ELECTRONICS (SHENZHEN) LTD. Address: Room 702, Unit D, 4 Building Shenzhen Software Industry Base, Xuefu Road, Nanshan District, Shenzhen, Guangdong, China

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS Chain 0 Chain 1 Antenna

ZIONCOM ELECTRONICS (SHENZHEN) LTD. Add: Building A1-A2,Lantian Science and Technology Park,Xinyu Road, Xinqiao Henggang Block, Shajing Street,Baoan District.Shenzhen ,China Tel: +86-755-6136 3299 Fax: +86-755-6136 3322 Email: lifm@zioncom.net FCC Confidential Authorization Date: 2019-07-25 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: X7D-IP04338 In accordance with Sections 0.457 and 0.459 of the Commissions Rules, (ZIONCOM ELECTRONICS

(SHENZHEN) LTD.) hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature:

Carmen Lee Product Manager QA-FR-171-A

ZIONCOM ELECTRONICS (SHENZHEN) LTD. Add: Building A1-A2,Lantian Science and Technology Park,Xinyu Road, Xinqiao Henggang Block, Shajing Street,Baoan District.Shenzhen ,China Tel: +86-755-6136 3299 Fax: +86-755-6136 3322 E-mail: lifm@zioncom.net Date: 2019-07-25 To:

FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Declaration Subject: FCC ID: X7D-IP04338 declaration of frequency bands restriction Dear Sir or Madam:

We, ZIONCOM ELECTRONICS (SHENZHEN) LTD., hereby declare that our product AC1200 Dual Band Smart Home Wi-Fi System, Model Number: T6 have the ability to work in 2.4G and 5G 4 frequency bands:

5150 MHz~5250 MHz,5250 MHz~5350MHz,5470 MHz~5725 MHz, 5725 MHz~5850 MHz. For the purpose of marketing, the frequency of the product sold in U.S. are programmed and locked to work only in 5150~5250MHz ,5725~5850 MHz, The other frequency bands 5250MHz~5350MHz, 5470 MHz~5725 MHz are disabled by firmware in factory. The end user or any other parties cannot have the capability to activate the other frequency bands. We applied for testing only frequency bands: 2412~2462MHz, 5180~5240 MHz, 5745~ 5825 MHz for the United States this time in BACL. Please contact me if you have any question. Signature:

Carmen Lee Product Manager

ZIONCOM ELECTRONICS (SHENZHEN) LTD. Add: Building A1-A2,Lantian Science and Technology Park,Xinyu Road, Xinqiao Henggang Block, Shajing Street,Baoan District.Shenzhen ,China Tel: +86-755-6136 3299 Fax: +86-755-6136 3322 Email: lifm@zioncom.net FCC Authorization 2019-07-25 Date:

FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We , ZIONCOM ELECTRONICS (SHENZHEN) LTD., Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Carmen Lee Product Manager QA-FR-170-B

ZIONCOM ELECTRONICS (SHENZHEN) LTD. Add:Building A1-A2,Lantian Science and Technology Park,Xinyu Road, Xinqiao Henggang Block, Shajing Street,Baoan District.Shenzhen ,China Tel: +86-755-6136 3299 Fax: +86-755-6136 3322 Email:lifm@zioncom.net DECLARATION OF SIMILARITY Date: 2019-07-25 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam:

We, ZIONCOM ELECTRONICS (SHENZHEN) LTD., hereby declare that the product: AC1200 Dual Band Smart Home Wi-Fi System, FCC ID: X7D-IP04338. model: IP04338 is electrically identical with the model: T6 which was tested by BACL with the same electromagnetic emissions and electromagnetic compatibility characteristics. A description of the differences between those models and that are declared similar are as follows:

They are the same product, and just the different model name, the rest are the same. Please contact me should there be need for any additional clarification or information. Best Regards, Signature:

Carmen Lee Product Manager