FCC ID: 2AJ9T-ML300 Bluetooth-Enabled Keypad Smart Lock

User Manual Model: ML300 Version: 1.0 English Table of Contents Product Overview...........................................................................................................1 Product Features............................................................................................................1 Lock Setup.......................................................................................................................2 Resetting the Lock..........................................................................................................................................2 Pairing the Lock with App............................................................................................................................2 Programming the Lock in Standlone Mode...........................................................................................3

*Adding the Smart Gateway........................................................................................................................6

*Connecting to Amazon Alexa or Google Assistant............................................................................6 How to Use......................................................................................................................7 Unlocking Door with Fingerprint..............................................................................................................7 Unlocking Door with Password..................................................................................................................7 Unlocking Door with App.............................................................................................................................7

*Unlocking Door with Voice Assistant.....................................................................................................7 Important Notes 1. 2. 3. 4. 5. 6. 7. Before registration, the new locks can be unlocked by any authentication method by default. An administrator must be registered rst, before any other operation in the Standalone Mode. Four alkaline AA batteries (not included) are needed to power the device. Non-

alkaline and rechargeable batteries ARE NOT RECOMMENDED. Do not remove batteries from the lock when it is operating. Batteries must be replaced when the lock ashes the red light along with 2-second beeps after being turned on. The locks are also equipped with mechanical keys for manual unlocking. Please keep the mechanical keys at a safe place. Fingerprint positioning tips:

Recommended ngers: Index, middle, or ring ngers; avoid using the thumb or pinky, as it is dicult to accurately press onto the ngerprint reader using those. Note: Please use the correct method when pressing your ngers onto the ngerprint reader for registration and identication. Our company will assume no liability for recognition issues that may result from incorrect usage of the product. We reserve the right of nal interpretation and modication concerning this point. Product Overview Keypad Fingerprint Sensor ZKTeco Button Handle(reversible) Mechanical Key Hole(hidden) Micro-USB Interface Battery Cover Battery Compartments Reset Button Outdoor Unit Indoor Unit User Introduction:

Product Features 1) 2) 3) 4) The maximum capacity of all users is 100. The maximum capacity of each verication method (ngerprint/password) is 100. The owner is the person who owns the lock and registers it in ZSmart App. and has all the privileges. Admin can always unlock via ngerprint, password, or App. Admin can add or delete normal users, and control all lock settings. Normal Users can always unlock via ngerprint, password, or App, and check the opening records. Initialization: All registered user data will be deleted and restored to the factory default setting. Random Password: To protect the password, users may enter their password with random digits before or after the actual password. The maximum number of entered digits must be less than or equal to 32. For example: If the correct password is 123456, then the random password can be 89123456807, 1234562363, 389123456, etc. Low Battery Warning: When the battery power is low, the lock will ash the red light along with 2-second beeps after being turned on. Then the batteries need to be replaced. Illegal Attempts Alert: After 5 failed verication attempts, the lock will ash the red light along with 10-second beeps and the lock will not be operable hereafter. 1 Emergency Charging: The bottom of the outdoor unit is provided with a Micro-USB interface. Use a power bank to charge the lock when it is out of power. Emergency Mechanical Key: The mechanical key is used to open the door when the lock has any electronic malfunction. Slide the key cover and insert the key to unlock in emergency situations. Bluetooth Connectivity: The lock is designed with BLE5.0 communication, you can unlock it via your smart phone when the Bluetooth is connected.

*Remote Access: This function is only available for the additional Smart Gateway. With the Smart Gateway installed, the lock can be controlled remotely via ZSmart App.

*Voice Assistant Control: This function is only available for the additional Smart Gateway. The lock can be unlocked using your voice commands through Amazon Alexa and the Google Assistant. Lock Setup Resetting the Lock Please note all registered user data will be deleted and restored to the factory default setting. If Paired with App: Tap the EDIT button on the upper right corner of Device Interface, and click Disconnect and wipe data to remove the lock from your ZSmart Account. Then press and hold the reset button until you hear one long beep and two short beeps. If Never Paired: Press and hold the reset button until you hear one long beep and two short beeps. Pairing the Lock with App Step 1 Search for the ZSmart App in iOS App Store or Google Play Store, or scan the QR code to download the App. 2 Step 2 Step 3 Step 4 Open the ZSmart App, register, and sign in to the account. Make sure the lock is in Factory Default Mode. Turn on Bluetooth permission on your smartphone, and stay near the lock (within 10 meters without obstacles). Tap the + button on the upper right corner, follow the on-screen instructions to pair the lock automatically, and start to use it. Notes: If you dont want to use the App, please check the next section i.e. "Programming the Lock in Standalone Mode"

Programming the Lock in Standalone Mode It is recommended to use ZSmart App to program your lock. If you dont have a smartphone or dont want to use the App, you can use the programming instructions below. Note:

Standalone Mode is not available after the lock is registered in App! Please reset the lock to Factory Default Mode first to program your lock in Standalone Mode. 3 1. Add the Admin Password in Standalone Mode Operation Indicators Status Press and hold the ZKTeco Button for 3 seconds 2 short beeps with ashing green light Enter a six-digit password and press ZKTeco Button 1 short beep with green light, then ashing green light Enter the same six-digit password and press ZKTeco Button again 1 short beep with green light Completed 2 short beeps with no light indication 2. Add the Admin Fingerprint in Standalone Mode Operation Indicators Status Press and hold the ZKTeco Button for 3 seconds 2 short beeps with ashing green light Press the nger onto the ngerprint sensor 1 short beep with green light, then ashing green light Press the same nger onto the ngerprint sensor again 1 short beep with green light, then ashing green light Press the same nger onto the ngerprint sensor again 1 short beeps with green light Completed 2 short beeps with no light indication 4 3. Add the User Password in Standalone Mode Operation Indicators Status Press and hold the ZKTeco Button for 3 seconds 2 short beeps with ashing blue light Verify the administrators identity with his/her ngerprint, or by entering the password then pressing the ZKTeco Button to conrm 1 short beep with green light, then ashing green light Enter a six-digit password and press the ZKTeco Button 1 short beep with green light, then ashing green light Enter the same six-digit password and press the ZKTeco Button again 1 short beep with green light Completed 2 short beeps with no light indication 4. Add the User Fingerprint in Standalone Mode Operation Indicators Status Press and hold the ZKTeco Button for 3 seconds 2 short beeps with ashing blue light Verify the administrators identity with his/her ngerprint, or by entering the password then pressing the ZKTeco Button to conrm 1 short beep with green light, then ashing green light Press the nger onto the ngerprint sensor 1 short beep with green light, then ashing green light Press the same nger onto the ngerprint sensor again 1 short beep with green light, then ashing green light Press the same nger onto the ngerprint sensor again 1 short beep with green light Completed 2 short beeps with no light indication 5 Note:

1) 2) 3) 4) Step 1 Step 2 Step 3 Step 4 Admin must be created before any other programming. Only one Admin is available in the Standalone Mode. The verication mode of an admin can be a ngerprint or a passcode. The registered password must be six digits. If you try to register the same ngerprint/password again, the lock will prompt one long beep with a red light.

*Adding the Smart Gateway Plug the Gateway into the outlet using the provided Power Adapter. Open the ZSmart App. Tap the + button on the upper right corner, and then select the Smart Lock / Wireless Gateway category. Follow the on-screen instructions to connect the Gateway to the 2.4GHz Wi-Fi network and complete the setup. Enter the device interface of Gateway, and then follow the on-screen instructions to select the corresponding lock to add.

*Connecting to Amazon Alexa or Google Assistant Tap the EDIT button on the upper right corner of the device interface. Select the Alexa or Google Assistant icon, then follow the on-screen instructions to link your ZSmart Account to Amazon Alexa or Google Assistant. After completing the setup, you can use the supported voice commands that include:

Alexa, unlock the front door. OK Google, unlock the front door. 6 How to Use Unlocking Door with Fingerprint Press the registered nger onto the ngerprint sensor. Then rotate the handle down to open the door. Unlocking Door with Password Enter the registered password and press the ZKTeco Button to conrm. Then rotate the handle down to open the door. Note:

1) 2) Note:

1) 2) You can press the ZKTeco Button to turn on the keypad backlight. Users may enter a random password to prevent any person from observing the password. The maximum length of a random password is 32 digits. Unlocking Door with App Turn on Bluetooth permission on your smartphone -> Open the App and press the UNLOCK button -> Rotate the handle down to open the door. If you have already paired the lock with the gateway, you dont need to turn on Bluetooth. When unlocking the lock via Bluetooth, please stay near the lock (within 10 meters without obstacles).

*Unlocking Door with Voice Assistant Perform the voice commands. Answer the additional voice security codes. Then rotate the handle down to open the door. Note: Once the Lock and Smart Gateway has been installed and congured correctly, make sure you enable the ZSmart Amazon Alexa Skill and Google Home Action rst before you can congure your voice to perform voice commands. 7 Warning:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement:

This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. IMPORTANT! Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. No.26,Pingshan 188 Industry zone,Tangxia Town, Dongguan City,Guangdong Province,China 523728 Tel:+86 769-82109991 Fax:+86 755-89602394 www.zkteco.com

4 ZK Tzca Bluetooth-Enabled Keypad Smart Lock Model: ML300 Input: 1. 5*4AA Battery Operating Temperature: -20C~55C Operating Humidity: 20%~93%

FCC ID: 2AJ9T-ML300 Made in China cr This device complies with Part 15 of eel ee eee ad Pea eee tes ae el eee eet anos eer Peer?

label location Bere ow a woo ee Ur Tn

ZKTECO CO., LTD. Letter of Authorization Company:

ZKTECO CO., LTD. Address:

No.26, Pingshan 188 Industry zone, Tangxia Town, Dongguan City, Guangdong Province, China 523728 Product Name: Bluetooth-Enabled Keypad Smart Lock Model Number: ML300, ML200 FCC Identifier: 2AJ9T-ML300 We authorize MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Zhonglie Ge Date: 2020-11-13 Title: Engineer

Differences Declaration To whom concern, We company ZKTECO CO., LTD. Here by declares:

The product model(s) ML200 is the same PCB layout, electronic schematic and Antenna with ML300, which tested in Shenzhen Huatongwei International Inspection Co., Ltd. They are the same model that has 2 names. Sincerely yours, Signature:

Name: Zhonglie Ge Company name: ZKTECO CO., LTD. Company address: No.26, Pingshan 188 Industry zone, Tangxia Town, Dongguan City, Guangdong Province, China 523728 E-Mail: gzl@zkteco.com

ZKTECO CO., LTD. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject; Request for Long Term Confidentiality Date: 2020-11-13 FCC ID: 2AJ9T-ML300 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Zhonglie Ge Title: Engineer