FCC ID: 2AJ9T-21201 RFID and QR Code Reader

 

QR50 QR Code Access Control

Reader

User Manual

Version：V1.0 Date：2021.04.01

Important statement

Copyright Notice

Thank you for choosing this product. Before use, please read this installation guide and

instruction manual (hereinafter referred to as the instruction manual) carefully to ensure that the

product is used correctly, has a good use effect and verification speed, and avoids unnecessary

damage to the product.

Without the written consent of the company, no one may copy or disseminate any content of

this manual in any form.

Disclaimer

Due to the continuous update of the product, the company cannot promise that the

information is consistent with the actual product, and it is not responsible for any disputes caused

by the inconsistency of the actual technical parameters with this information. Any changes will

not be notified in advance. The company reserves the right of final modification and

interpretation.

1

Revision Record

Version

Revision Content

Revision Date

V1.0

All New

2021/04/01

2

Contents

IMPORTANT STATEMENT ......................................................................................................................... 1

REVISION RECORD ..................................................................................................................................... 2

CONTENTS ..................................................................................................................................................... 3

1、INSTALL EQUIPMENT .......................................................................................................................... 4

2、PRODUCT INTRODUCTIONS .............................................................................................................. 5

3、WIRING INSTRUCTIONS ...................................................................................................................... 5

3.1 WIRING DEFINITION .................................................................................................................................. 5

3.2 OPERATING INSTRUCTIONS ....................................................................................................................... 5

4、OPERATION AND SETTING OF CARD READER ............................................................................ 7

4.1 ONE-KEY CONFIGURATION ........................................................................................................................ 7

4.2 BASIC OPERATION OF CARD READER ....................................................................................................... 9

4.3 WIEGAND SETTING ................................................................................................................................... 12

4.4 READ CARD SETTING ................................................................................................................................ 13

4.5 READER OPERATION ................................................................................................................................. 14

4.6 UPGRADE FIRMWARE ............................................................................................................................... 14

3

1、Install Equipment

Installation notes: In order to ensure the normal use of the equipment, users are requested to strictly follow the

installation instructions

1

3

Face shell (with panel)

Remove the cover (with panel) from

the device. It is necessary to gently

remove the panel from the USB port

side to avoid damage to the LED light

when removing it

2

or

60mm

66mm

4

Buy the standard type 86 dark (bottom) bo

x from the market, and the installation hole

distance is 60mm or 66mm. The installer di

gs a hole on the wall surface according to t

he length, width and depth of the standard

86-type dark (bottom) box to place the dar

k (bottom) box and fix it with cement sand

The device has this boss facing

downwards during installation

When

installing, connect the wire and

debug it, then put the device into the

86-type concealed (bottom) box as shown

in the figure, and fix the device with two

M4*15PB mechanical screws. Pay attention

to the downwards on the device with the

boss.

The panel is printed upright, and the notch under the

shell is aligned with the boss under the device

First find the right alignment point, and then

buckle the shell (with panel) into the device

(as shown in the figure), pay attention to the

assembly direction during installation and

check whether the printing on the rear panel

is upright.

4

2、Product Introductions

The QR code access control card reader is a new generation of smart access control card reader

developed by our company. The product has high-end appearance, fast scanning speed, high

recognition rate, strong compatibility, and can be connected to any access control controller that

supports Wiegand input. It adapts to various application scenarios, supports identification of RFID

radio frequency cards and QR codes, and can be used in community management, visitor

management, hotel management, unmanned supermarkets and other fields.

The characteristics of the QR code reader as followed：

⚫ Development of new QR code access control technology.

⚫ The card reader comes with a card reader antenna, the working frequency is 125KHz.

⚫ Support ID，MF，CPU，NFC (analog card)，Desfire EV1，and QR code.

⚫ Support Wiegand，RS485，USB (upgrade use).

3、Wiring Instructions

3.1 Wiring Definition

From the reverse side (pictured above) from left to right：

DC(+12V)

485B WG0

485A

GND

WG1

VCC

GND

RS485 Port

Wiegand Port

NC

/

NC

NC

NC

/

/

/

3.2 Operating Instructions

Note: During use, please follow the wiring definition of the QR code reader to connect with other devices. In

addition, what is mentioned below is only part of the wiring between the QR code reader and the controller,

and does not represent all the wiring definitions of the controller. Please refer to the actual controller wiring

definitions.。

5

①First, connect the QR code reader to the controller via Wiegand or RS485, and then connect

1.Wiegand or RS485 Communication

the +12V power supply.

The QR code reader does not need to be connected to the lock body when it is used as a reader.

The controller in the figure only lists part of the wiring. In addition, there are many ways

to connect between the machines. Refer to the following figure for the common connection

methods of Wiegand or RS485：

②Then, put the card or QR code (paper, electronic, mobile phone) into the recognition range

of the card reader, and the card reader will automatically obtain and transmit the information

carried by the card or QR code to the controller.

2.USB Communication

①First, connect the QR code reader to the PC through the USB interface.

6

②Then, open the "HID keyboard" in the DEMO software settings, and then put the card or

QR code (paper, electronic, mobile phone) into the recognition range of the card reader, the

card reader will automatically obtain the information carried by the card or QR code And

transmit to the PC terminal, can demonstrate through the text document.

4、Operation and Setting of Card Reader

Introduce how to configure the card reader through Demo software.

4.1 One-key Configuration

Operation steps

1. Connect the QR code reader to the computer with a USB cable, open the Demo software, select

the USB port, click "OK", the connection is successful. (Note: If you choose serial port

connection, the default baud rate is 115200）

Note：Support Connection Configuration tool via USB and serial port。

USB：Connect to the configuration tool via USB communication。

COM：Connect the configuration tool through RS485 communication。

7



2. Successfully connected, click download in the download configuration area below。

3. Prompt that the download configuration is complete, and the QR code reader configuration

can be completed with one click, the operation is simple。

8

4.2 Basic Operation of Card Reader

-----The End

Operation Steps

1. If the user needs to set the parameters of the QR code reader by himself, open the Demo

software, after the connection is successful, enter the QR50 advanced settings page in

the upper right corner of the page。

9

2. Enter the main page of advanced settings。

3. On the "Reader operation" page, set the configuration parameters of the card reader as

a) Click "Function Selection" on the "Function Selection" interface to view the

configuration information of the current card reader。

required。

10



reader。

Params

RS485 address

Unlock time

b) The user can set the parameter information of the card reader by himself, and then

click "write configuration" to configure the parameter information of the QR code

Description

0: Broadcast address, that is, no matter the machine's 485 address is

set to 0~255, it can be connected by communication.

If the 485 address of the machine is set to 1~255, fill in the

corresponding, and it can also be connected by communication。

When the card reader is directly connected to the door lock and the

card/QR code with normal door opening permission is swiped, the door

opening time。

serial number

Device serial number of the card reader。

RS485 Function

Turn on/off the RS485 communication mode of the card reader.

The configuration tool can still be connected through 485 when closed。

RS485 Active

upload

When it is turned on, the card reader data is automatically uploaded to

the server under the 485 interface.

When closed, the card reader data will not be uploaded to the server。

Wiegand

Function

Work mode

HID keyboard

Turn on or off Wiegand mode.

Note: The DEMO switch has no effect. Wiegand output is also available

when the Wiegand mode is turned off。

Reading head mode: When connecting a card reader, select the reading head

mode, and set the parameters of the reading head through the DEMO

software.

Note: Only reader mode is supported!

When it is turned on, the USB communication can transfer the card number

(the card does not support)/QR code data to the computer (such as a text

file).

When closed, the card/QR code will have normal feedback, but the USB will

11

not transfer the card number/QR code data to the computer。

Baud rate

If you choose a serial port connection, you can set the baud rate。

Write

configuration

When the above parameters are modified, click "write configuration" to

make the new configuration effective。

Read

configuration

Get the current configuration of the card reader and display it。

Support resetting the card reader to factory settings。

-----The End

4.3 Wiegand setting

Operating Steps

On the "Wiegand Parameter Settings" page, set Wiegand related parameters。

Wiegand Mode

Can choose Wiegand 26、34、66。

Output format

Parity check

When Wiegand outputs the card number, the card number can

be output in Positive/reverse direction。

Whether to transmit Wiegand parity bit, optional

output/non-output。

Pulse Width

Wiegand pulse width, optional (1~99)*10ms

Pulse interval

Wiegand pulse gap, optional (0~89)*100+1000ms。

Write configuration

After setting the above parameters, click "write

configuration" to make the new configuration effective。

Read configuration

Get the current configuration of the card reader and

12

display it。

-----The End

4.4 Read card setting

Operating Steps

On the "Reader parameter settings" page, set the reading parameters of the card reader。

Custom settings to read the CPU card physical card

number, MF physical card number

After setting the parameters, click "write configuration" to write the information into the

Click "Read Configuration" to display the configuration information of the card reader。

card reader。

-----The End

13

4.5 Reader operation

Operating Steps

n the "Reader Operation" page, set the relevant parameters of the card reade 。

Search device

Get version

Click "Search device" to view the communication address of

the card reader。

Note：If you select the RS485 address, you can click "Search

device" to get the correct device address before you can

perform other operations。

Click "Get Version " to view the version number information

of the card reader

Read RTC

Write RTC

Get the time of the card reader。

Set the time of the card reader.

Real-time write RTC The time when the card reader is connected to the PC.

-----The End

4.6 Upgrade Firmware

Operating Steps

n the "Firmware Upgrade" page, click "Open File", select the upgrade program, click the "Start

Upgrade" button, unplug and plug the USB to reconnect the machine to the computer, check the prompt

message, and the upgrade is successful.

14



15



FCC Warning:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any inte rference received, including

interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

•

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Increase the separation between the equipment and receiver.

The End

16



 

 

 

 

 

 

 

 

 

 

Report No.:TB-FCC180630

1

Page:

10

of

Appendix ⅠFCC ID Label

FCCID: 2AJ9T-21201

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received including

,

interference that may cause undesired operation.

Size for the label: 40mm X 25mm

FCC ID: 2AJ9T-21201 TB-RF-074-1.0



Report No.:TB-FCC180630

2

Page:

10

of

Appendix Ⅱ ID Label Location

ID LOCATION

FCC ID: 2AJ9T-21201 TB-RF-074-1.0



 

 

Add: No.32,Pingshan Industrial Avenue,Tangxia Town,Dongguan City,Guangdong Province,China 523728 We, ZKTECO CO., LTD. Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model:

Date: 2021-7-13 FCC ID: 2AJ9T-21201 Dear Sir/Madam, Product name: RFID and QR Code Reader Model no.: QR50BE, QR50WE Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Zhonglie Ge/

ZKTECO CO., LTD.

+86 0755 89602277

+86 0755 89602674 GZL@ZKTECO.COM No.32,Pingshan Industrial Avenue,Tangxia Town,Dongguan City,Guangdong Province,China 523728

 

 

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2021-7-13>

Pursuant to Paragraphs 0.457 and 0.459 of the Commission s Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID 2AJ9T-21201 Model name QR50BE For the product stated above, we request confidential;

that the following information be held Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our information that could be of benefit to our competitors. trade secrets and proprietary The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Zhonglie Ge/

ZKTECO CO., LTD.

+86 0755 89602277

+86 0755 89602674 GZL@ZKTECO.COM No.32,Pingshan Industrial Avenue,Tangxia Town,Dongguan City,Guangdong Province,China 523728

 

 

ZKTECO CO., LTD. No.32,Pingshan Industrial Avenue,Tangxia Town,Dongguan City,Guangdong Province,China 523728 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

2021-7-13 We, ZKTECO CO., LTD. the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AJ9T-21201 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Zhonglie Ge/

ZKTECO CO., LTD.

+86 0755 89602277

+86 0755 89602674 GZL@ZKTECO.COM No.32,Pingshan Industrial Avenue,Tangxia Town,Dongguan City,Guangdong Province,China 523728