all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 1.80 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | ID Label/Location Info | |||||||
1 | Internal Photos | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report |
1 | Users Manual | Users Manual | 1.80 MiB |
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station
& RF Remote Station Installation Manual ZTE CORPORATION ZXCBTS (V5.4) CDMA Micro Base Transceiver Station/RF Remote Station Installation Manual Manual Version Product Version V5.4 20050422-R1.1 Copyright 2004 ZTE Corporation All rights reserved. No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any means without the prior written permission of ZTE Corporation.
ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P.R.China Website: http://www.zte.com.cn Postcode: 518057 Customer Support Center: (+86755) 26771900 800-9830-9830 Fax: (+86755) 26770801 Email: support@zte.com.cn
S.N.: sjzl20030272 FAX+86-755-26770160 Suggestions and Feedback To improve the quality of ZTE product documentation and offer better services to our customers, we hope you can give us your suggestions and comments on our documentation and fax this form to
+86-755-26770160; or mail to Marketing center 3rd floor ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China. Our postcode is 518057. ZXCBTS (V5.4) CDMA Micro Base Transceiver Station/RF Remote Stations Installation Manual V5.4 Document version 20050422-R1.1 Document name Product version Equipment installation time Your information Name Postcode Telephone Company Company address E-mail Presentation: How is information presented? (Introductions, procedures, illustrations, others)
Good Fair Average Poor Bad Your evaluation of this documentation Accessibility: Can you find the information you want? (Table of contents, Index, headings, numbering, others)
Good Fair Average Poor Bad Intelligibility: Can you understand it when you find it? (Language, vocabulary, readability, others)
Good Fair Average Poor Bad Presentation:
Your suggestions for improvement of this documentation Accessibility:
Intelligibility:
Your other suggestions on ZTE product documentation Preface About This Manual This manual presents the hardware installation procedures of ZXCBTS micro base transceiver stations (BTSs)/remote stations. It is one of ZTE manual series for CDMA cellular mobile communications system. It aims to providing guidance to the engineering personnel who install ZTE CDMA micro-BTS/remote stations, as well as offering reference for the equipment maintenance personnel. Correct hardware installation is the basis for reliable and normal running of the base transceiver stations, thus enjoying importance in engineering construction. To facilitate the installation, this manual is written following the sequence of actual hardware installation. First, it briefs the structure of the ZXCBTS products, which is helpful for the installation personnel to get familiar with the equipment. Next, it describes the equipment installation procedures in detail. Finally, it presents how to check the equipment after the installation. How to Use This Manual 1. Overview Introduces the basic structure, basic installation procedures and points for attention during installation of the micro-BTS/remote stations. 2. Preparations Introduces the preparations for the installation, including listing needed tools and checking the installation environment. 3. Open-box Inspection Introduces the procedures and cautions for opening boxes and inspecting the equipment. 4. Installation of Cabinet Details the fixation and installation of the cabinet of the equipment. 5. Installation of Power Supply System Details the installation of the power supply system of the equipment. 6. Installation of Grounding System Details the installation of the grounding system of the equipment. 7. Connection of Cables Details the check of internal cable connections between various modules, as well as type selection and connection of external cables. 8. Installation of Primary Antenna Feeder System Details the installation of the antenna feeder system of the equipment, including the procedures of assembling feeder cable connectors, installing antenna, laying feeder cables, installing feeder cable window and grounding equipment. 9. Installation of GPS antenna feeder system Details the installation of GPS antenna feeder system for the equipment, including the procedures of assembling feeder cable connectors and installing antenna. 10. Installation of Internal Modules Details the installation of internal modules. 11. Hardware Installation Check Presents how to check the hardware installation. 12. Power-on and Power-off Presents the procedures of powering on/off the equipment. 13. Appendix Presents the equipment performance specifications, meaning of various indicators and connection of cables. Conventions 1. Notational Convention Angular brackets < > identify names of keys and buttons, and the information typed by an operator from a terminal. Square brackets [ ] indicate a man-machine interface, menu item, data list or field name. The symbol separates a multi-level menu, for example, [FileNewFolder] indicates the
[Folder] menu item under the [New] submenu of the menu [File]. 2. Keyboard Operation Convention Format
<Key>
<Key1+Key2>
<key1, Key2>
Description Indicate a key or button name, for example, <Enter>, <Tab>,
<Backspace>, and <a>. Press Key 1 and Key 2 at the same time. Press Key1 first. Then release Key 1 and press Key 2. 3. Mouse Operation Convention Format Description Click Double-click Right-click Drag Refers to clicking the primary mouse button (usually the left mouse button) once Refers to quickly clicking the primary mouse button (usually the left mouse button) twice Refers to clicking the secondary mouse button (usually the right mouse button) once. Refers to pressing and holding a mouse button and move the mouse 4. Danger, Warning, Caution and Note Statements Note, Caution, Danger statements are used throughout this manual to emphasize important and critical information. You must read these statements to help ensure safety and to prevent product damage. Warning, Statement: The actual product may differ from what is described in this manual due to frequent update of ZTE products and fast development of technologies. Please contact the local ZTE office for the latest updating information of the product. FCC & IC STATEMENT Before using this CDMA Micro Base Transceiver Station & RF Remote Station, read this important RF energy awareness and control information and operational instructions to ensure compliance with the FCC and IC RF exposure guidelines. NOTICE: Working with the equipment while in operation, may expose the technician to RF electromagnetic fields that exceed FCC rules for human exposure. Visit the FCC website at www.fcc.gov/oet/rfsafety to learn more about the effects of exposure to RF electromagnetic fields. Changes or modifications to this unit not expressly approved by the party responsible for compliance will void the users authority to operate the equipment. Any change to the equipment will void FCC and IC grant. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to the FCC and IC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. For OUTDOOR use, a PNALE Antenna with a maximum gain of 17dBi is authorized for use with this unit. Outside antennas must be positioned to observe minimum separation of 2M (6.56 feet.) for 800MHz unit and 1.5M (4.92 feet.) for 1900MHz unit from all users and bystanders. For the protection of personnel working in the vicinity of outside (uplink) antennas, the following guidelines for minimum distances between the human body and the antenna must be observed. The installation of an OUTDOOR antenna must be such that, under normal conditions, all personnel cannot come within 2M (6.56 feet) for 800MHz unit and 1.5M (4.92 feet) for 1900MHz unit from the outside antenna. Exceeding this minimum separation will ensure that the worker or bystander does not receive RF-exposure beyond the Maximum Permissible Exposure according to section 1.1310 i.e. limits for Controlled Exposure. Contents 1 Overview ..................................................................................................................................................1-1 1.1 Introduction to Micro-BTS ............................................................................................................1-1 1.2 Installation Overview.....................................................................................................................1-4 1.3 Installation Flow ............................................................................................................................1-5 1.4 Points for Attention ........................................................................................................................1-7 2 Preparations ............................................................................................................................................2-1 2.1 Installation Environment Check.....................................................................................................2-1 2.1.1 Checking Equipment Building Conditions..........................................................................2-1 2.1.2 Checking Indoor Environment............................................................................................2-1 2.1.3 Checking Power Supply System .........................................................................................2-2 2.1.4 Checking Grounding System ..............................................................................................2-2 2.1.5 Checking Relative Devices .................................................................................................2-2 2.2 Tools and Instruments ....................................................................................................................2-2 2.3 Technical Documents .....................................................................................................................2-3 3 Open-box Inspection...............................................................................................................................3-1 3.1 Checking Packing List and Goods .................................................................................................3-1 3.2 Packaging.......................................................................................................................................3-2 3.3 Open-box Procedures.....................................................................................................................3-2 4 Installation of Cabinet ............................................................................................................................4-1 4.1 Installation Flow ............................................................................................................................4-1 4.2 Installation Modes..........................................................................................................................4-2 4.2.1 Installing Cabinet on Pole ...................................................................................................4-2 4.2.2 Installing Cabinet on Wall...................................................................................................4-6
-i-
5 Installation of Power Supply System .................................................................................................... 5-1 5.1 Introduction to Power Cables ........................................................................................................ 5-1 5.1.1 -48V DC Power Cable ........................................................................................................ 5-1 5.1.2 120V AC Power Cable........................................................................................................ 5-2 5.2 Connection of Power Cables ......................................................................................................... 5-2 5.3 Assembling Power Cable Connector ............................................................................................. 5-3 5.3.1 Assembling -48V DC Power Cable Connector................................................................... 5-3 5.3.2 Assembling 120V AC Power Cable Connector .................................................................. 5-5 6 Installation of Grounding System ......................................................................................................... 6-1 6.1 Introduction to the Grounding System........................................................................................... 6-1 6.2 Installing Grounding System ......................................................................................................... 6-2 6.2.1 Installing Outdoor Grounding Copper Busbar.................................................................... 6-2 6.2.2 Installing the Grounding System of Micro-BTS................................................................. 6-3 6.2.3 Installing Feeder Cable Grounding Kit............................................................................... 6-4 7 Connection of Cables.............................................................................................................................. 7-1 7.1 Checking Internal Cable Connections ........................................................................................... 7-1 7.1.1 Type and Configuration of Internal Cables......................................................................... 7-1 7.1.2 Connection of Internal Cables ............................................................................................ 7-3 7.2 Connecting External Cables .......................................................................................................... 7-3 7.2.1 Connecting Optical Fiber.................................................................................................... 7-3 7.2.2 Connecting Multi-carrier Interconnection RF Cables......................................................... 7-7 7.2.3 Waterproof Processing of Joints ......................................................................................... 7-8 7.2.4 Connection of Trunk Cables ............................................................................................... 7-9 8 Installation of Primary Antenna Feeder System.................................................................................. 8-1 8.1 Preparations ................................................................................................................................... 8-1 8.1.1 Installation Personnel.......................................................................................................... 8-1
-ii-
8.1.2 Installation Environment.....................................................................................................8-2 8.1.3 Security Measures ...............................................................................................................8-2 8.1.4 Installation Tools.................................................................................................................8-2 8.2 Composition and Installation Requirements of Antenna Feeder System .......................................8-3 8.2.1 Composition........................................................................................................................8-3 8.2.2 Technical Parameters...........................................................................................................8-5 8.3 Installation Flow ............................................................................................................................8-5 8.4 Installation of Antenna ...................................................................................................................8-6 8.4.1 Determining Installation Location ......................................................................................8-6 8.4.2 Installing Accessories of Directional Antenna ....................................................................8-7 8.4.3 Transporting and Raising Antenna ......................................................................................8-8 8.4.4 Installing and Adjusting Directional Antenna .....................................................................8-9 8.4.5 Installing and Adjusting Omni Antenna ............................................................................8-10 8.4.6 Connecting Jumper Cable with Antenna and Sealing Their Joint.....................................8-10 8.5 Installation of Feeder Cable Window...........................................................................................8-11 8.6 Connection of Feeder Cable.........................................................................................................8-12 8.6.1 Determining Route for Feeder Cable ................................................................................8-13 8.6.2 Assembling Connectors of Primary Feeder Cable ............................................................8-13 8.6.3 Cutting Feeder Cable.........................................................................................................8-16 8.6.4 Raising Primary Feeder Cable...........................................................................................8-17 8.6.5 Laying and Fastening Primary Feeder Cable ....................................................................8-18 8.6.6 Connecting Jumper Cable with Feeder Cable and Sealing Their Joint .............................8-20 8.6.7 Leading Primary Feeder Cable into Equipment Room .....................................................8-21 8.6.8 Connecting Indoor Jumper Cable......................................................................................8-23 8.7 Grounding System of Micro-BTS................................................................................................8-23 8.8 Test of Antenna Feeder System....................................................................................................8-26
-iii-
8.9 Waterproof Processing of Connectors.......................................................................................... 8-26 9 Installation of GPS Antenna Feeder System ........................................................................................ 9-1 9.1 Preparations ................................................................................................................................... 9-1 9.1.1 Installation Personnel.......................................................................................................... 9-1 9.1.2 Installation Environment..................................................................................................... 9-1 9.1.3 Security Measures............................................................................................................... 9-2 9.1.4 Installation Tools................................................................................................................. 9-2 9.2 Composition of GPS Antenna Feeder System ............................................................................... 9-3 9.3 Installation Procedures................................................................................................................... 9-3 9.4 Test of Antenna Feeder System...................................................................................................... 9-5 10 Installation of Internal Modules........................................................................................................ 10-1 10.1 Overview ................................................................................................................................... 10-1 10.1.1 Logical Positions of Equipment Modules....................................................................... 10-1 10.1.2 Layout of Internal Modules ............................................................................................ 10-2 10.1.3 Functions of the Modules ............................................................................................... 10-4 10.2 Module Installation Flow........................................................................................................... 10-7 10.3 Installation and Replacement of Modules.................................................................................. 10-8 10.3.1 Installation Sequence ...................................................................................................... 10-8 10.3.2 Table of Cable Connections............................................................................................ 10-8 10.3.3 Fastening and Bundling of Internal Cables..................................................................... 10-9 10.3.4 Installation of OIM ....................................................................................................... 10-11 10.3.5 Installation of LFM....................................................................................................... 10-12 10.4 Points for Attention.................................................................................................................. 10-12 11 Hardware Installation Check..............................................................................................................11-1 11.1 Checking Components in the Cabinet........................................................................................ 11-1 11.2 Checking the Cabinet................................................................................................................. 11-1
-iv-
11.3 Checking Cables.........................................................................................................................11-2 11.4 Checking Power Cables and Grounding Cables.........................................................................11-2 11.5 Checking T1 Cables ...................................................................................................................11-4 11.6 Checking Indoor 1/2 Jumper Cables ........................................................................................11-4 11.7 Checking Primary Feeder Cables and GPS Feeder Cables ........................................................11-5 11.8 Checking Water-blocking Curve for Feeder Cable Window and Primary Feeder Cables..........11-6 11.9 Checking Hangers ......................................................................................................................11-6 11.10 Checking Outdoor 1/2 Jumper Cables....................................................................................11-7 11.11 Checking Antenna ....................................................................................................................11-7 11.12 Checking Standing Wave Ratio of Feeder Cables....................................................................11-9 11.13 Checking Indoor and Outdoor Environment ............................................................................11-9 12 Power-on and Power-off .....................................................................................................................12-1 12.1 Checking Components in the Cabinet before Power-on ............................................................12-1 12.2 Checking External Cables before Power-on ..............................................................................12-2 12.3 Powering on/off the Cabinet ......................................................................................................12-2 13 Installing the Integrated Micro-BTS.................................................................................................13-1 13.1 Introduction to the Solution of Micro-BTS Integration .............................................................13-1 13.1.1 Implementation of the Micro-BTS Integration ...............................................................13-1 13.1.2 Micro-BTS Integration Solution .....................................................................................13-2 13.1.3 Module Layout of the Integrated Micro-BTS and RF Remote Station ...........................13-4 13.1.4 Networking Modes of the Integrated SDH......................................................................13-7 13.2 Installing the Built-in SDH of Micro-BTS.................................................................................13-7 13.2.1 Position and Internal Connection of the Built-in SDH in the Micro-BTS ......................13-7 13.2.2 Connecting the External Optical Fibers and Cables During Installation.........................13-8 13.3 Installing the Integrated UPS of Micro-BTS/RF Remote Station ............................................13-10 13.3.1 Introduction to ZXUPS L010........................................................................................13-10
-v-
13.3.2 Precautions for UPS Installation................................................................................... 13-11 13.3.3 Structural Feature and Installation Mode of UPS ......................................................... 13-12 13.3.4 Installing the Engineering Cables of L010UPS ............................................................ 13-13 13.3.5 Installing UPS............................................................................................................... 13-14 13.4 Installing the Ancillary Combinational Power Supply of Micro-BTS/RF Remote Station ..... 13-15 13.4.1 Installing the Outdoor Power Box ................................................................................ 13-15 13.4.2 Installing the Outdoor Battery Box............................................................................... 13-17 13.4.3 Cable Connection for Outdoor Power Box................................................................... 13-17 Appendix A Packaging, Storage and Transportation ............................................................................ A-1 A.1 Packaging..................................................................................................................................... A-1 A.2 Storage ......................................................................................................................................... A-1 A.3 Transportation.............................................................................................................................. A-2 Appendix B Table of Cable Connections .................................................................................................B-1 B.1 Cable Connections in M800T Single-carrier Micro-BTS .............................................................B-1 B.2 Cable Connections in M800T Double-carrier Micro-BTS............................................................B-2 B.3 Cable Connections in R800T Single-carrier Remote Stations ......................................................B-3 B.4 Cable Connections in R800T Double-carrier Remote Stations.....................................................B-5 B.5 Cable Connections in M190T Single-carrier Micro-BTS .............................................................B-6 B.6 Cable Connections in M190T Double-carrier Micro-BTS............................................................B-7 B.7 Cable Connections in R190T Single-carrier Remote Stations ......................................................B-8 B.8 Cable Connections in R190T Double-carrier Remote Stations.....................................................B-9 B.9 Cable Connections in M802T Single-carrier Micro-BTS ...........................................................B-10 B.10 Cable Connections in M802T Double-carrier Micro-BTS........................................................B-12 B.11 Cable Connections in R802 Single-carrier RF Remote Stations...............................................B-13 B.12 Cable Connections in R802T Double-carrier Remote Stations.................................................B-14 B.13 Cable Connections in M191T Single-carrier Micro-BTS .........................................................B-15
-vi-
B.14 Cable Connections in M191T Double-carrier Micro-BTS....................................................... B-16 B.15 Cable Connections in R191T Single-carrier Remote Stations.................................................. B-18 B.16 Cable Connections in R191T Double-carrier Remote Stations ................................................ B-19 B.17 Cable Connections in M192T Single-carrier Micro-BTS......................................................... B-20 B.18 Cable Connections in M192T Double-carrier Micro-BTS....................................................... B-21 B.19 Cable Connections in R192T Single-carrier Remote Stations.................................................. B-22 B.20 Cable Connections in R192T Double-carrier Remote Stations ................................................ B-23 Appendix C Equipment Parameters .......................................................................................................C-1 C.1 Dimension .................................................................................................................................... C-1 C.2 Power Consumption ..................................................................................................................... C-1 Appendix D Indicators..............................................................................................................................D-1 D.1 BDM Indicators............................................................................................................................D-1 D.2 Indicators on Front Panel of MGPS .............................................................................................D-1 D.3 Indicators of LFM, RFM and OIM ..............................................................................................D-2 Appendix E Abbreviations ....................................................................................................................... E-1
-vii-
A List of Figures Fig. 1.1-1 Structure of ZXCBTS M800T Micro-BTS.......................................................................1-2 Fig. 1.1-2 Structure of Remote Stations............................................................................................1-3 Fig. 1.1-3 Connection between Remote Station and Macro-BTS.....................................................1-3 Fig. 1.1-4 Connection between Remote Station and Macro-BTS.....................................................1-4 Fig. 1.2-1 Schematic Diagram of the Hardware Installation of Micro-BTS/Remote Station ...........1-5 Fig. 1.3-1 Hardware Installation Flow Diagram ...............................................................................1-6 Fig. 3.2-1 Packing Box for ZXCBTS Cabinet ..................................................................................3-2 Fig. 3.3-1 Schematic Diagram for Opening a Box............................................................................3-3 Fig. 4.1-1 Flow of Installing the Cabinet ..........................................................................................4-2 Fig. 4.2-1 Schematic Diagram of Fastening the Cabinet onto the Pole (step 1) ...............................4-3 Fig. 4.2-2 Schematic Diagram of Fastening the Cabinet onto the Pole (step 2) ...............................4-4 Fig. 4.2-3 Schematic Diagram of Fastening the Cabinet onto the Pole (step 3) ...............................4-4 Fig. 4.2-4 Schematic Diagram of the Cabinet Fastened onto the Pole..............................................4-5 Fig. 4.2-5 Schematic Diagram of Installing the Support onto the Wall ............................................4-6 Fig. 4.2-6 Schematic Diagram of Installing the Cabinet onto the Wall.............................................4-7 Fig. 5.1-1 Four-pin Connector and Four-core Power Cable .............................................................5-1 Fig. 5.2-1 Connection of Power Cables and Grounding Cables at the Bottom of a Cabinet............5-3 Fig. 5.3-1 Assembling a Power Cable Connector (step 1) ................................................................5-3 Fig. 5.3-2 Assembling a Power Cable Connector (step 2) ................................................................5-4 Fig. 5.3-3 Assembling a Power Cable Connector (step 4) ................................................................5-4 Fig. 5.3-4 Assembling a Power Cable Connector (step 5) ................................................................5-5 Fig. 5.3-5 Assembling a Power Cable Connector (step 6) ................................................................5-5 Fig. 6.1-1 Schematic Diagram of Grounding Connections...............................................................6-2
-i-
Fig. 6.2-1 Appearance of a Grounding Copper Busbar .................................................................... 6-3 Fig. 6.2-2 Connection of Power Cable and PGND Cable at the Bottom of a Cabinet...................... 6-4 Fig. 6.2-3 Structure of a Grounding Kit............................................................................................ 6-5 Fig. 6.2-4 Schematic Diagram of Wrapping Waterproof Adhesive Tape Around the Grounding Cable
............................................................................................................................................................. 6-6 Fig. 7.2-1 Structure of Optical Fiber (1)........................................................................................... 7-3 Fig. 7.2-2 Structure of Optical Fiber (2)........................................................................................... 7-4 Fig. 7.2-3 Structure of Optical Fiber (3)........................................................................................... 7-5 Fig. 7.2-4 Structure of Optical Fiber (4)........................................................................................... 7-5 Fig. 7.2-5 Schematic Diagram of Connecting Optical Fiber ............................................................ 7-6 Fig. 7.2-6 Connection of Interconnection RF Cables ....................................................................... 7-8 Fig. 7.2-7 Connection of T1 Cables.................................................................................................. 7-9 Fig. 8.2-1 Typical Structure of the Antenna Feeder System ............................................................. 8-4 Fig. 8.3-1 Antenna Installation Flow................................................................................................ 8-6 Fig. 8.4-1 Installation of the KATHREIN Antenna .......................................................................... 8-7 Fig. 8.4-2 Schematic Diagram of Raising the Antenna to the Tower Top ........................................ 8-8 Fig. 8.4-3 Schematic Diagram of Adjusting the Pitch Angle of the Antenna ................................. 8-10 Fig. 8.5-1 Structure of a Feeder Cable Window ............................................................................. 8-12 Fig. 8.6-1 Structure of the Feeder Cable of a Micro-BTS/Remote Station..................................... 8-13 Fig. 8.6-2 Cutter for Assembling 7/8 Feeder Cable Connectors ................................................... 8-14 Fig. 8.6-3 Schematic Diagram of Cutting the Feeder Cable with the Cutter.................................. 8-14 Fig. 8.6-4 Schematic Diagram of Correct Cutting Size.................................................................. 8-14 Fig. 8.6-5 Schematic Diagram of Expanding the External Copper Conductor............................... 8-15 Fig. 8.6-6 Schematic Diagram of Connecting the Front Part with the Back Part of the Connector 8-15 Fig. 8.6-7 Schematic Diagram of Fastening the Front Part with the Back Part of the Connector .. 8-16 Fig. 8.6-8 Schematic Diagram of Pulling the Feeder Cable Up the Tower..................................... 8-18 Fig. 8.6-9 Appearance of a Hanger................................................................................................. 8-19
-ii-
Fig. 8.6-10 Schematic Diagram of Wrapping Waterproof Adhesive Tape (1).................................8-20 Fig. 8.6-11 Schematic Diagram of Wrapping Waterproof Adhesive Tape (2).................................8-21 Fig. 8.6-12 Schematic Diagram of Wrapping Waterproof Adhesive Tape (3).................................8-21 Fig. 8.6-13 Leading the Feeder Cable into the Equipment Room - Mode 1 ...................................8-22 Fig. 8.6-14 Leading the Feeder Cable into the Equipment Room - Mode 2 ...................................8-22 Fig. 8.7-1 Structure of a Grounding Kit ..........................................................................................8-24 Fig. 8.7-2 Schematic Diagram of Wrapping Waterproof Adhesive Tape Around the Grounding Cable
...........................................................................................................................................................8-25 Fig. 9.2-1 Composition of the GPS Antenna Feeder System ............................................................9-3 Fig. 9.3-1 Schematic Diagram of Length of Cable Sheath to be Stripped ........................................9-4 Fig. 9.3-2 Schematic Diagram of Soldering the Core Wire with the Pin ..........................................9-4 Fig. 9.3-3 Structure of N-J7A............................................................................................................9-4 Fig. 10.1-1 Modules and Boards in M800T/M801T/M802T/M190T/M191T/M192T Micro-BTS10-1 Fig. 10.1-2 Modules and Boards in R800T/R801T/R802T/R190T/R191T/R192T ........................10-2 Fig. 10.1-3 Layout of Modules in a ZXCBTS Micro-BTS.............................................................10-3 Fig. 10.1-4 Layout of Modules in a ZXCBTS Remote Station.......................................................10-4 Fig. 10.2-1 Module Installation Flow Diagram...............................................................................10-7 Fig. 10.3-1 Schematic Diagram of Bundling Internal Cables (1)....................................................10-9 Fig. 10.3-2 Schematic Diagram of Bundling Internal Cables (2)..................................................10-10 Fig. 10.3-3 Schematic Diagram of Bundling Internal Cables (3)..................................................10-10 Fig. 10.3-4 Corresponding Relations between OIM Expansion Slots in BDM and Sectors.........10-11 Fig. 10.3-5 Schematic Diagram of Inserting the OIM into the BDM ...........................................10-12 Fig. 12.1-1 Setting of S1 .................................................................................................................12-1 Fig. 13.1-1 Solution (I) of Micro-BTS Integration ............................................................................13-3 Fig. 13.1-2 Solution (II) of Micro-BTS Integration ...........................................................................13-4 Fig. 13.1-3 Layout of Modules in the ZXCBTS micro-BTS .............................................................13-5 Fig. 13.2-1 Cable Layout of the Built-in SDH in the CDMA Micro-BTS.........................................13-8
-iii-
Fig. 13.2-3 Connection of the Optical Fiber.................................................................................... 13-10 Fig. 13.3-1 Appearance of the ZXUPS L010 Series........................................................................ 13-11 Fig. 13.3-2 Inner Structure of the ZXUPS L010 Series................................................................... 13-11 Fig. 13.3-4 Layout of the Monitoring Cables of the CDMA Micro-BTS 485/Dry Contact ............ 13-14 Fig. 13.4-6 Output Connecting Terminal of the Dry Contact .......................................................... 13-19 Fig. C.1-1 Appearance of a ZXCBTS Cabinet .................................................................................C-1 Fig. D.1-1 Indicators of the BDM.................................................................................................... D-1 Fig. D.3-1 Location of Indicators on the OIM Panel ...................................................................... D-4
-iv-
A List of Tables Table 1.1-1 List of ZXCBTS Micro-BTS/Remote Stations (800MHz) ............................................1-1 Table 1.1-2 List of ZXCBTS Micro-BTS/Remote Stations (1900MHz) ..........................................1-1 Table 2.2-1 Tools and Instruments Needed for the Installation.........................................................2-2 Table 5.1-1 Corresponding Relationship between Core Wires and Binding Posts............................5-2 Table 5.1-2 Corresponding Relationship between Core Wires and Binding Posts............................5-2 Table 5.3-1 Corresponding Relationship between Core Wires and Binding Posts...........................5-6 Table 7.1-1 List of Types and Configurations of Internal Cables......................................................7-1 Table 13.2-1 Cable Connection of the Built-in SDH inside the CDMA Micro-BTS.........................13-7 Table 13.3-1 From-to-list of the CDMA Micro-BTS 485/dry contact supplementary cables..........13-13 Table B.1-1 Cable Connections in M800T Single-carrier Micro-BTS ............................................ B-1 Table B.2-1 Cable Connections in M800T Double-carrier Micro-BTS........................................... B-2 Table B.3-1 Cable Connections in R800T Single-carrier Remote Stations...................................... B-3 Table B.4-1 Cable Connections in R800T Double-carrier Remote Stations.................................... B-5 Table B.5-1 Cable Connections in M190T Single-carrier Micro-BTS ............................................ B-6 Table B.6-1 Cable Connections in M190T Double-carrier Micro-BTS........................................... B-7 Table B.7-1 Cable Connections in R190T Single-carrier Remote Stations...................................... B-8 Table B.8-1 Cable Connections in R190T Double-carrier Remote Stations.................................... B-9 Table B.9-1 Cable Connections in M802T Single-carrier Micro-BTS .......................................... B-10 Table B.10-1 Cable Connections in M802T Double-carrier Micro-BTS....................................... B-12 Table B.11-1 Cable Connections in R802T Single-carrier Remote Stations.................................. B-13 Table B.12-1 Cable Connections in R802T Double-carrier RF Remote Stations .......................... B-14 Table B.13-1 Cable Connections in M191T Single-carrier Micro-BTS......................................... B-15 Table B.14-1 Cable Connections in M191T Double-carrier Micro-BTS....................................... B-16
-i-
Table B.15-1 Cable Connections in R191T Single-carrier Remote Stations ..................................B-18 Table B.16-1 Cable Connections in R191T Double-carrier Remote Stations.................................B-19 Table B.17-1 Cable Connections in M192T Single-carrier Micro-BTS .........................................B-20 Table B.18-1 Cable Connections in M192T Double-carrier Micro-BTS........................................B-21 Table B.19-1 Cable Connections in R192T Single-carrier Remote Stations ..................................B-22 Table B.20-1 Cable Connections in R192T Double-carrier Remote Stations.................................B-23 Table C.2-1 Power Consumption of Several Types of Micro-BTS and Remote Stations.................C-2 Table C.2-2 Power Consumption of Several Types of Micro-BTS and Remote Stations.................C-2 Table C.2-3 Power Consumption of Several Types of Micro-BTS and Remote Stations.................C-3 Table D.2-1 Indicators on the Front Panel of MGPS....................................................................... D-1 Table D.3-1 Indicators of the LFM.................................................................................................. D-2 Table D.3-2 Indicators of the RFM.................................................................................................. D-3 Table D.3-3 Indicators on the OIM Panel........................................................................................ D-4
-ii-
1 Overview
Summary
Listing the components to be installed.
Describing the installation flow.
Presenting points for attention during the installation 1.1 Introduction to Micro-BTS With the development of various new technologies, Base Transceiver Station (BTS) is oriented to be small and intelligent, with low power consumption, low cost and high reliability. In large or medium-sized cities, common micro-BTS cannot meet the demand of some busy-traffic areas due to the block of high buildings. In addition, it is a waste for micro-BTS to be installed in some remote areas with less traffic. Moreover, micro-BTS have high requirements on the equipment room environment. To avoid the above problems, ZTE has developed ZXCBTS products. ZXCBTS products are classified based on different frequency bands and transmitter powers. This manual serves for the installation of the following models:
Table 1.1-1 List of ZXCBTS Micro-BTS/Remote Stations (800MHz) Model Name ZXCBTS M800T CDMA micro-BTS (800MHz) ZXCBTS M802T CDMA micro-BTS (800MHz) ZXCBTS R800T CDMA remote station (800MHz) ZXCBTS R802T CDMA remote station (800MHz) Rated Transmission Power 10W 20W 10W 20W Table 1.1-2 List of ZXCBTS Micro-BTS/Remote Stations (1900MHz) Model Name ZXCBTS M190T CDMA micro-BTS (1900MHz) ZXCBTS M191T CDMA micro-BTS (1900MHz) Rated Transmission Power 5W 10W 1-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Model Name ZXCBTS M192T CDMA micro-BTS (1900MHz) ZXCBTS R190T CDMA remote station (1900MHz) ZXCBTS R191T CDMA remote station (1900MHz) ZXCBTS R192T CDMA remote station (1900MHz) Rated Transmission Power 20W 5W 10W 20W ZXCBTS products include micro-BTS and remote stations, working in the frequency bands of 800MHz and 1.9GHz. Micro-BTS system consists of Baseband Digital Subsystem (BDS), Timing &
Frequency Subsystem (TFS), power supply subsystem, lightning protection subsystem and of M800T/M802T//M190T/M191T/M192T micro-BTS is illustrated in the following figure. Subsystem Frequency structure
(RFS). Radio The GPS antenna RF antenna Micro-BTS T1 (4) BDS subsystem
(BDM) BSC, macro-/
micro-BTS TFS subsystem
(GPSTM) RFS subsystem
(MTRX, MPA, MLNA, MDUP and MDIV) Power supply GPS, RF antenna feeder and power lightning arrester Fig. 1.1-1 Structure of ZXCBTS M800T Micro-BTS Remote stations are similar to micro-BTS in structure, but different in replacing Baseband Digital Module (BDM) with Remote Fiber Module (RFM) and removing GPS Timing Module (GPSTM), for the clock signals of remote stations are demodulated from the signals sent through optical fiber. The structure of remote stations is illustrated in the following figure. 1-2 Chapter 1 Overview RF antenna Optical fiber RFM RFS (MTRX, MDUP and MDIV) Power supply RF antenna feeder and power lightning arrester Fig. 1.1-2 Structure of Remote Stations Remote stations should cooperate with the macro-/micro-BTS to achieve the BTS functions, so you need to configure Local Fiber Module (LFM) on micro-BTS or Optical Interface Module (OIM) on micro-BTS for interworking with the remote stations. If the LFM is configured in a macro-BTS, the connection between the remote station and the macro-BTS is illustrated in the following figure. Macro-BTS R F I M L F M Optical fiber R F M RX TX RX DIV RX MLNA RX DUP RX MLNA RX TX MPA TX MTRX Remote station Fig. 1.1-3 Connection between Remote Station and Macro-BTS If the OIM is configured in a micro-BTS, the connection between the remote station and the micro-BTS is illustrated in the following figure. 1-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual B D M O I M Micro-BTS Optical fiber R F M RX TX RX DIV RX MLNA RX DUP TX MPA TX MTRX RX MLNA RX Remote station Fig. 1.1-4 Connection between Remote Station and Macro-BTS 1.2 Installation Overview The hardware installation of micro-BTS/remote stations can be divided into the following aspects:
1. 2. 3. Installing shelf and boards, connecting internal cables and setting DIP switches Installing the power supply system Installing the grounding system 4. Locating and installing the antenna, jumper cable and feeder cable, and testing the antenna feeder system 5. Installing GPS and its feeder cables 6. Connecting trunk cables and assembling their connectors 7. Installing the alarm system for reporting abnormal temperature and humidity See Fig. 1.2-1. 1-4 Chapter 1 Overview Install the GPS Install the antenna system Install the ZXCBTS cabinet Install the shelf Check internal cables Set the DIP switches Install the power supply system Install the grounding system Connect trunk cables Install the sunshade cover Fig. 1.2-1 Schematic Diagram of the Hardware Installation of Micro-BTS/Remote Station 1.3 Installation Flow Install the equipment following the specified procedures strictly:
1. Install the support;
2. Locate the cabinet on the support;
3. Secure the cabinet;
4. Install the sunshade cover (necessary for outdoor installation);
5. Connect power cables and grounding cables of the cabinet;
6. Connect T1 cables of the cabinet;
7. 8. 9. Install the primary antenna feeder system to connect with the RF cables;
Install the GPS;
Install and test the boards and modules, and set the DIP switches;
10. Check the installation. See Fig. 1.3-1. 1-5 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Engineering Survey Report BTS Engineering Design and Construction Drawing Environment Acceptance Report Cabling rack Power supply system Grounding system Other accessories Packing list Start Preparation for engineering installation Check construction conditions Open-box inspection Goods are correct Yes Install the shelf Install the power supply system Install the grounding system Check cable connections in the shelf Connect trunk cables Check the primary antenna feeder system Install the GPS Set DIP switches Hardware installation check End No Goods Error Feedback List Goods Replacement Feedback List Fig. 1.3-1 Hardware Installation Flow Diagram 1-6 Chapter 1 Overview 1.4 Points for Attention Pay attention to the following points during the installation: The installation personnel should be trained to obtain the qualification entitled by ZTE and read this manual before the installation. 1. Do not operate on the cabinet or any module when the power is on. 2. Observe the relative requirements strictly when installing the BTS. 3. Do not install the antenna feeder system in thunder weather. 4. Before the thunder storm season of each year comes, check whether the lightning arrester is in good condition and is well contacted. If it is damaged, replace it immediately. 5. When the installation of the cabinet completes, lock the door immediately. If the door need be opened in case of maintenance, contact the professional personnel for help. 1-7 2 Preparations
Summary
Describing the installation environment check.
Listing the installation tools.
Listing the installation. technical documents needed for 2.1 Installation Environment Check The items to check:
2.1.1 Checking Equipment Building Conditions Check if the layout, height, bearing capability, shock-proof ability, doors and windows, walls and troughs of the equipment building meet the requirements. 2.1.2 Checking Indoor Environment Check the temperature, humidity, air pressure, ventilation condition, antistatic protection measures, anti-interference measures, dustproof measures, rodent-resistant measures, fire-protection facility, lighting condition, water supply and drainage system of the equipment room. interference strength should be no more To the highest priority, the equipment should be installed on the cool and dry walls indoors with good ventilation; the fire-protection facility should be equipped; there should be no caustic gas or smog in the room and no leakage on the roof; the electromagnetic than 140dBV/m
(0.01MHz~110000MHz). Or the equipment can be installed on the shady walls outdoors with good ventilation and rain blocks. To the least priority, the equipment can be installed on common walls, towers or high poles. The operating temperature range of the equipment is between -40C and +55C, and the relative humidity range is between 5% and 100%. 2-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 2.1.3 Checking Power Supply System Check the power supply ability and quality. A group of independent and stable 85V~138V (nominal 120V) AC power should be supplied to the equipment. It is prohibited to share the power supply with other high-power telecom equipment or the usually powered-down equipment. 2.1.4 Checking Grounding System The standard grounding system should be equipped and the resistance should be less than 5 ohm. 2.1.5 Checking Relative Devices Check if the other devices relative to the normal operation of the equipment are in good condition, such as interface device, transmission device, Digital Distribution Frame
(DDF) and Optical Distribution Frame (ODF). 2.2 Tools and Instruments Prepare the tools and instruments needed for the installation in advance as listed in Table 2.2-1. Table 2.2-1 Tools and Instruments Needed for the Installation Type Name Special tools Drilling tools General tools One cutter for assembling feeder cable connectors One 75-ohm coaxial cable stripper 75-ohm coaxial crimping plier One multi-functional crimping plier One multimeter One SiteMaster standing wave ratio tester One earth resistance tester One percussive drill Several drill bits One cleaner One power connector board (with at least three two-pin and three-pin sockets respectively; the current capacity is more than 15 amp.) Three cross screw-drivers (4, 6 and 8) Three straight screw-drivers (4, 6 and 8) Four adjustable wrenches (6, 8, 10 and 12) 2-2 Chapter 2 Preparations Type Name Two spanners (17 and 19) One hexagon spanner One socket wrench One 5kg nail hammer One 300W electric iron and one 40W electric iron One coil of solder wires One 50m tape measure One 5m steel tape measure One 400mm horizontal ruler One inclinometer One compass One multimeter Ruler One plumb Antistatic wrist strap Safety helmet, slip-proof gloves One hacksaw, several saw blades One sharp nose plier (8) One diagonal plier (8) One slip joint plier (8) One vice (8) A set of files (middle) One tweezers One paint brush One scissors One dryer One solder removal tool One hydraulic pressure pliers One crowbar Pulley group Rope Ladder Forklift Measurement tools Protection tools Locksmith tools Assistant tools 2.3 Technical Documents Prepare the following technical documents:
1. Engineering Survey Report, BTS Engineering Design and Construction Drawing, Environment Acceptance Report 2-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Engineering Survey Report should be filled by the technical engineers of the equipment provider during site survey. If they can not carry out the survey in time, you should survey the site, fill in the report and then send it to the equipment provider. This report is used for the preparation of construction materials. BTS Engineering Design and Construction Drawing should be prepared by the design unit you entrusted, and a copy should be provided to the equipment provider before the delivery. Environment Acceptance Report is used by the technical engineers of the equipment provider to check the construction environment during site survey. If any inconformity is found, you are required to solve the problem. Before the construction, the second check will be implemented. 2. ZXCBTS(V5.4)CDMA Micro Base Transceiver Stations/RF Remote Stations Installation Manual, ZXCBTS(V5.4)CDMA Micro Base Transceiver Stations/RF Remote Stations Technical Manual, ZXCBTS(V5.4)CDMA Micro Base Transceiver Hardware Manual, ZXCBTS(V5.4)CDMA Micro Base Transceiver Stations/RF Remote Stations Maintenance Manual Stations/RF Stations Remote 3. Installation Acceptance Report, Test Acceptance Report Installation Acceptance Report and Test Acceptance Report should be offered to you by the equipment provider during delivery. Installation Acceptance Report is filled after the BTS installation completes. Test Acceptance Report is filled during the BTS commissioning. 2-4 3 Open-box Inspection
Summary
Describing the inspection procedures.
Describing the open-box procedures. 3.1 Checking Packing List and Goods
Caution Because ZXCBTS equipment is expensive, ensure that it is packed well and the flags for avoiding water and vibrations are marked. Load and unload the equipment gently, and avoided damage from sunshine and rain. 1. Check the ZTE delivery sheet. 2. Open-box inspection should be done by the engineering supervisor and your representative. First, check if the total quantity of the goods is correct according to the packing list, if the packing boxes are in good condition, and if the delivery location is the right installation site. 3. Next, open the boxes and the engineering supervisor should check the goods based on the packing list. Open-box Inspection Report is put in the packing box numbered 1#. Open the 1# box and take out the Open-box Inspection Report to check if the total quantity of the goods is consistent with the checklist, and then archive the report. 4. During the inspection, if loss of goods, lack of goods, error delivery or any damage is found, find out the cause and feedback to the ZTE headquarter for handling. 5. The goods are packed in either cartons or wooden boxes. You need to open them on site using different tools. 3-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 3.2 Packaging
Note The cabinets of micro-BTS and remote stations are the same in structure, so is the packaging method. Put the support and other accessories of the ZXCBTS cabinet into the wooden box. In the wooden box, the cabinet is packed with foam boards, a bubble bag and a plastic bag. After opening the box, you need not uplift it but directly take the equipment out. When carrying the box, be cautious to prevent the cabinet from being damaged. The packing box for the ZXCBTS cabinet is shown in Fig. 3.2-1. CDMA micro-BTS Goods:
Net Weight: (Kg) Volume: 81x52x40 (cm) Qty.:
Packing List:
ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P.R.China Postcode: 518057 Tel: (+86755) 6790000 Customer Support Center: 8008301118 Fig. 3.2-1 Packing Box for ZXCBTS Cabinet 3.3 Open-box Procedures Follow the steps below to open the box:
1. Open the cover board. 2. Remove the foam boards. 3. Take the micro-BTS out directly. See Fig. 3.3-1. 3-2 Chapter 3 Open-box Inspection Accessories Micro-BTS CDMA micro-BTS ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P.R.China Postcode: 518057 Tel: (+86755) 6790000 Customer Support Center: 8008301118
s d o G o i g t W e N e V o l u m e
Q t y k i n a P c Fig. 3.3-1 Schematic Diagram for Opening a Box 3-3
4 x 2 x 1 5 h t
: 8 g L i
t s
( K g
0
) c m ) 4 Installation of Cabinet
Summary
Describing the procedures to install the micro-BTS/remote station cabinet
Describing the possible installation modes 4.1 Installation Flow
Note The cabinets of ZXCBTS micro-BTS/remote stations are the same in structure, so is the installation method. The cabinet can be installed in two modes: on pole or on wall. The installation flow is shown in Fig. 4.1-1. 4-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Installation on pole Installation on wall Install the support Outdoors Install the support Install the sunshade cover Indoors Install the cabinet Installation check End Fig. 4.1-1 Flow of Installing the Cabinet 4.2 Installation Modes
Note The cabinets of ZXCBTS micro-BTS/remote stations are the same in structure, so is the installation method. As shown in Fig. 4.1-1, the cabinet can be installed either on pole or on wall based on the actual environment. 4.2.1 Installing Cabinet on Pole 1. Disassemble the support from the cabinet. 2. Secure the support onto the pole with fixing plates and 260mm-long bolts. The diameter of the pole should be between 60mm and 90mm. 75mm is recommended. See Fig. 4.2-1. If the equipment is to be installed outdoors, face the front side southward and the back side northward (This rule is applicable to the case that the equipment is 4-2 Chapter 4 Installation of Cabinet installed in the Northern Hemisphere. If it is installed in the Southern Hemisphere, the opposite rule should be applied). 3. Install the sunshade cover onto the support with four M4 bolts. See Fig. 4.2-4. 4. Hold the cabinet to hang it onto the support, then push it into the shelf. See Fig. 4.2-2. 5. Align the bolt holes on the support with those on the cabinet, and then screw down four M8 hexagon bolts. See Fig. 4.2-3. 6. On the cabinet base there are hangers for rope. If necessary, use the rope to hang the cabinet onto the pole. See Fig. 4.2-1 for the schematic diagram of cabinet fastened on pole. Bolt Flat washer Support M12 nut, spring washer, flat washer Pole Fixing plate Fig. 4.2-1 Schematic Diagram of Fastening the Cabinet onto the Pole (step 1) 4-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Fig. 4.2-2 Schematic Diagram of Fastening the Cabinet onto the Pole (step 2) Fig. 4.2-3 Schematic Diagram of Fastening the Cabinet onto the Pole (step 3) 4-4 Chapter 4 Installation of Cabinet Fig. 4.2-4 Schematic Diagram of the Cabinet Fastened onto the Pole
Caution For your safety, be sure to wear the safety belt when working at heights and the safety helmet when working at grounds. It is prohibited to work in thunder storm weather. 4-5 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 4.2.2 Installing Cabinet on Wall 1. Disassemble the support from the cabinet. 2. Mark four points on the wall based on the four holes on the support, and then drill four holes with a percussive drill (using M12 drill bit). Secure the support onto the wall with four M10 expansion bolts. See Fig. 4.2-5. 3. Hold the cabinet to hang it onto the support, and then push it into the shelf. 4. Align the bolt holes on the support with those on the cabinet, and then screw down four M8 hexagon bolts. 5. Install the sunshade cover if the equipment is to be installed outdoors. See Fig. 4.2-6 for the schematic diagram of installing cabinet on wall. Wall Support Expansion bolt Hexagon nut Washer Fig. 4.2-5 Schematic Diagram of Installing the Support onto the Wall 4-6 Chapter 4 Installation of Cabinet Fig. 4.2-6 Schematic Diagram of Installing the Cabinet onto the Wall
Note The modules and cables in micro-BTS (including ultra-wide coverage micro-BTS) and remote stations have been installed, connected and tested before delivery. Before commissioning, you only need to check if they are loose due to conveyance. Refer to Chapter 7 for the connection of cables between cabinets. According to the configuration requirement, you might need to add optical fiber modules or CSM5000 expansion modules in the expansion slots of the corresponding BDM board. If any fault occurs, the maintenance personnel can refer to this manual for simple maintenance. 4-7 5 Installation of Power Supply System
Summary
Describing the methods for installing the power supply system..
Describing the procedures to install the power supply system.. 5.1 Introduction to Power Cables The micro-BTS/remote stations are supplied by 120V AC power or -48V DC power. AC micro-BTS are supplied by 120V AC power, and DC micro-BTS are supplied by
-48V DC power. 5.1.1 -48V DC Power Cable The ZTE -48V DC ZXCBTS equipment is equipped with a piece of 10m-long cable, which can meet the installation requirement in most cases. If you need to assemble the cable on site in special cases, follow the instructions in this section. The DC power cable connector is a four-pin connector, and the power cable adopts four-core cable, as shown in Fig. 5.1-1. The corresponding relationship between the core wires and the binding posts are listed in Table 5.1-1. Fig. 5.1-1 Four-pin Connector and Four-core Power Cable 5-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Table 5.1-1 Corresponding Relationship between Core Wires and Binding Posts Binding Post No. Color of Core Wire Power Polarity 1 2 3 4 Blue Red Black Olivine
-48V
-48V
-48VGND
-48VGND 5.1.2 120V AC Power Cable The ZTE 120V AC ZXCBTS equipment is equipped with a piece of 10m-long cable, which can meet the installation requirement in most cases. If you need to assemble the cable connector on site in special cases, follow the instructions in this section. The AC power cable connector is a three-pin connector, and the power cable adopts three-core cable. Refer to Table 5.1-2 for the corresponding relationship between the core wires and the binding posts. Table 5.1-2 Corresponding Relationship between Core Wires and Binding Posts Binding Post No. Color of Core Wire Power Polarity 1 2 3 Yellow and green Brown Blue PE L N 5.2 Connection of Power Cables 120V AC power supply and -48V DC power supply are used for the micro-BTS and remote stations. A waterproof connector is used to connect the power to the POWER terminal at the bottom of a cabinet, as shown in Fig. 5.2-1. 1. Select a suitable type of power cable. If the cabinet is installed outdoors, outdoor shielded power cables should be used for power supply, which can withstand the influences of ultraviolet lights, rains and temperature changes. If common three-core AC power cables are used in special cases, PVC pipes should be added for protection. If the cabinet is installed indoors, common three-core power cables can be used for power supply. 5-2 Chapter 5 Installation of Power Supply System 2. Power cables should be laid in order. If they are laid in parallel with T1 signal cables, an interval of 200mm is required between them. 3. Upon bundling of power cables, the space between two cable ties should be less than 0.5m to prevent friction with the tower upon swing of cables and avoid damage of power cable sheath. The power cable with a round connector for connecting the POWER terminal at the bottom of the cabinet PGND terminal of the cabinet Fig. 5.2-1 Connection of Power Cables and Grounding Cables at the Bottom of a Cabinet 5.3 Assembling Power Cable Connector 5.3.1 Assembling -48V DC Power Cable Connector Step 1: Put the connector components 1, 2, 3, 4 and 5 onto the cable, as shown in Fig. 5.3-1. 4 3 2 1 5 Fig. 5.3-1 Assembling a Power Cable Connector (step 1) 5-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Step 2: Strip the 17mm-long sheath off the four-core cable at the end to be welded. If the sheath of more than 17mm is stripped, the component 3 cannot press the cable tight;
if less than 17mm, inconvenience might be caused for installation. See Fig. 5.3-2. 4 3 2 1 5 Fig. 5.3-2 Assembling a Power Cable Connector (step 2) Step 3: Strip the 5mm-long insulation layer off the four core wires respectively, twist up the copper core wires and brush a slice layer of soldering tin on them, and then put a 10~15mm-long heat-shrink tube onto each core wire. Step 4: Joint the core wires respectively with the binding posts of the component 6 by welding them, push the heat-shrink tubes to the proper position and then make them shrink, as shown in Fig. 5.3-3. Refer to Table 5.1-1 for the corresponding relationship between the core wires and the binding posts. 4 3 2 1 6 5 Fig. 5.3-3 Assembling a Power Cable Connector (step 4) 5-4 6 Chapter 5 Installation of Power Supply System Step 5: Screw to connect the component 5 with the component 6, as shown in Fig. 5.3-4. 4 3 2 1 5 Fig. 5.3-4 Assembling a Power Cable Connector (step 5) Step 6: Push the components 2, 3 and 4 into the component 5, and then screw down the component 1 onto the component 5. Be sure to screw the component 1 but not 5. See Fig. 5.3-5. 1 6 5 Fig. 5.3-5 Assembling a Power Cable Connector (step 6) 5.3.2 Assembling 120V AC Power Cable Connector The steps for assembling an AC power cable connector are the same as that for assembling a DC power cable connector. The only difference is that the three-pin connector and three-core power cable are used for AC power cables. Refer to the preceding contents for the procedures and Table 5.3-1 for the corresponding relationship between the core wires and the binding posts. 5-5 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Table 5.3-1 Corresponding Relationship between Core Wires and Binding Posts Binding Post No. Color of Core Wire Power Polarity 1 2 3 Yellow and green Brown Blue PE L N 5-6 6 Installation of Grounding System
Summary
Describing the method for installing the grounding system 6.1 Introduction to the Grounding System This section details the procedures to install the grounding system, including grounding copper busbar and feeder cable grounding kit. Grounding aims to protecting both the human being and the equipment against lightning shock and electromagnetic interference. The grounding system is composed of indoor groundings, outdoor groundings and underground grounding net. The grounding system of a ultra-wide coverage micro-BTS includes protection grounding on the chassis, lightning arrester for RF components in the cabinet, for GPS antenna, for T1 cables, for 120V AC power and for feeder cable grounding kit. The customer needs to complete the construction of the basic grounding net and the grounding system of the tower and other buildings, and offer the points for connecting the indoor and outdoor grounding busbars to the grounding net through different 50mm2 wires. The conductor led from the PGND terminal of the shelf is connected to the grounding copper busbar, and the conductor led from the -48VGND of the shelf is connected to the DC power copper busbar. Each feeder cable should be connected to the outdoor grounding copper busbar through the cable grounding kit before being led into the equipment room. See Fig. 6.1-1. 6-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Tower platform Feeder cable grounding kit Feeder cable Grounding cable (35mm2) M i c r o
B T S D C p o w e r r a c k O t h e r d e v i c e s Outdoor grounding busbar Indoor grounding busbar PGNDs of all devices in the equipment room (including the cabling rack) are connected to the indoor grounding busbar Grounding cable (50mm2) Fig. 6.1-1 Schematic Diagram of Grounding Connections 6.2 Installing Grounding System 6.2.1 Installing Outdoor Grounding Copper Busbar U The outdoor grounding copper busbar functions in lightning protection. It is usually installed on the wall outside the equipment room, and the best position is right under the feeder cable window or on the rain-proof wall of the feeder cable well on the top of a building. 6-2 Chapter 6 Installation of Grounding System In actual installation, first determine the position for the copper busbar based on the engineering design drawing, and then install the busbar on the wall with expansion bolts. See Fig. 6.2-1 for the appearance of the grounding copper busbar. Fig. 6.2-1 Appearance of a Grounding Copper Busbar 6.2.2 Installing the Grounding System of Micro-BTS The cabinets of ultra-wide coverage micro-BTS/remote stations are equipped with PGND terminals, as shown in Fig. 6.2-2. The PGND terminal is connected to the indoor grounding copper busbar via the 16mm2 yellow or olivine conducting wire. If the equipment is installed outdoors, the PGND terminal is connected with the grounding cable from the tower or from the top of the building in the crimping connection mode. 6-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual PGND terminal of the cabinet Fig. 6.2-2 Connection of Power Cable and PGND Cable at the Bottom of a Cabinet 6.2.3 Installing Feeder Cable Grounding Kit
Caution:
It is prohibited to install the grounding kit in thunderstorm weather; otherwise, the installation personnel might be hurt. When installing the grounding kit, be sure to keep the feeder cable at the joint straight. 6.2.3.1 Grounding Principles of Primary Feeder Cable 1. Generally, each primary feeder cable should be grounded at least three times for lightning protection, that is, on the tower platform, between the tower and the outdoor cabling rack, and on the wall before the feeder cable is led into the equipment room. If the primary feeder cable is more than 60 meters long, a lightning grounding kit should be installed every 20 meters. 2. The antenna feeder system, antenna mount and newly-installed cabling rack should all be welded to the lightning protection net of the building. The feeder cable should also be grounded at three points, that is, on the antenna pole, on the rooftop, and on the wall before the feeder cable is led into the equipment room. 3. Before leading the primary feeder cable along the outdoor cabling ladder from the top of the building to the equipment room, check whether the cabling ladder is grounded. If not, request the network operator to accomplish it as soon as possible. 6-4 Chapter 6 Installation of Grounding System 6.2.3.2 Procedures to Install a Grounding Kit 1. Prepare such tools as paper knife, straight screwdriver, spanner and sharp nose pliers. 2. Choose a suitable position for installing the grounding kit, and cut the sheath off the 7/8" feeder cable based on the size of the grounding kit. The structure of a grounding kit is shown in Fig. 6.2-3. Grounding terminal Grounding cable Feeder cable Grounding wire clip Out-layer copper core of feeder cable Sheet copper of feeder cable Fig. 6.2-3 Structure of a Grounding Kit 3. Lead the grounding cable of the lightning grounding kit to the grounding net. Keep the angle between the grounding cable and the primary feeder cable no more than 15. If the antenna feeder system is installed on a tower, lead the grounding cable downward along the tower. If the antenna feeder system is installed on the top of a building, lead the grounding cable to the lightning protection net. 4. Before installing the grounding kit, wrap the waterproof adhesive tape around the grounding cable near the grounding copper for sealing, as shown in Fig. 6.2-4. 6-5 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Fig. 6.2-4 Schematic Diagram of Wrapping Waterproof Adhesive Tape Around the Grounding Cable 5. Clamp the external conductor with the grounding copper and clip tightly. 6. Seal the joint between the grounding kit and the feeder cable as follows:
First wrap the waterproof adhesive tape and then the PVC tape around the joint.
Wrap the waterproof adhesive tape circularly from bottom upward, and then from top downward, finally from bottom upward again. Note that the next circle covers 1/2 of the previous circle. 7. Connect the grounding terminal of the grounding kit to the tower body or the cabling rack on the top of the building (the cabling rack is connected to the lightning protection net). Remove the paint and oxide at the junction within the radius of 13mm and then coat the clean area with antioxidant cream. After the connection, paint the area with antirust paint. 8. Before the primary feeder cable is led into the equipment room, connect the grounding terminal of the grounding kit to the outdoor grounding busbar. 6-6 7 Connection of Cables
Summary
Describing the connection of internal cables.
Describing the connection of external cables. 7.1 Checking Internal Cable Connections 7.1.1 Type and Configuration of Internal Cables There are 422 or 485 internal cables totally. Refer to Table 7.1-1 for the types and configurations of internal cables in micro-BTS/remote stations. Type RF cables Table 7.1-1 List of Types and Configurations of Internal Cables Name Applied Equipment RF21 RF22 RF23 RF24 RF25 RF26 RF27 RF28 RF32 RF33 RF34 RF35 RF36 RF37 RF38 RF42 Single-carrier 800M micro-BTS/remote stations Single-carrier and double-carrier 800M micro-BTS/remote stations Single-carrier and double-carrier 800M micro-BTS/remote stations Single-carrier and double-carrier 800M micro-BTS/remote stations All micro-BTS/remote stations Single-carrier and double-carrier 800M micro-BTS/remote stations Single-carrier and double-carrier 800M micro-BTS/remote stations Single-carrier and double-carrier 800M micro-BTS/remote stations Single-carrier 1.9G micro-BTS/remote stations Single-carrier and double-carrier 1.9G micro-BTS/remote stations Single-carrier and double-carrier 1.9G micro-BTS/remote stations Single-carrier 1.9G micro-BTS/remote stations Single-carrier and double-carrier 1.9G micro-BTS/remote stations Single-carrier 1.9G micro-BTS/remote stations Single-carrier and double-carrier 1.9G micro-BTS/remote stations All double-carrier micro-BTS/remote stations 7-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Type Name Applied Equipment Clock cables Communication cables Power cables Fan cables Grounding cables Alarm cables All micro-BTS/remote stations All double-carrier micro-BTS/remote stations All single-carrier and double-carrier micro-BTS Single-carrier and double-carrier 800M micro-BTS Single-carrier and double-carrier 800M micro-BTS Single-carrier and double-carrier 1.9G micro-BTS All single-carrier and double-carrier remote stations All single-carrier and double-carrier remote stations All micro-BTS/remote stations All micro-BTS/remote stations All micro-BTS/remote stations All micro-BTS/remote stations All AC-powered micro-BTS/remote stations All AC-powered micro-BTS/remote stations All micro-BTS/remote stations configured with heater All AC-powered micro-BTS/remote stations RF43 RF29 RF30 RF31 RF39 RF40 RF41 BDM-GPS All single-carrier and double-carrier micro-BTS MPA CONTL RXTDX DCDX01 DCDX02 DCDX03 ACDX01 ACDX02 ACDX03 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 F-FAN-004 All single-carrier and double-carrier micro-BTS Single-carrier and double-carrier 20W micro-BTS/remote stations F-FAN-005 Single-carrier and double-carrier 20W micro-BTS/remote stations F-FAN-006 All micro-BTS/remote stations DX01 All micro-BTS/remote stations DX02 DX03 All micro-BTS/remote stations MONDX01 All micro-BTS/remote stations MONDX02 All micro-BTS/remote stations DX04 DX05 DX06 All single-carrier and double-carrier micro-BTS All single-carrier and double-carrier remote stations All micro-BTS/remote stations All DC-powered micro-BTS/remote stations All DC-powered micro-BTS/remote stations All DC-powered micro-BTS/remote stations Among these cables, only ACDX04 (AC power cable) and F-DC PWR-002 (DC power cable) are delivered with the equipment, and other cables have been connected in the equipment before delivery. 7-2 Chapter 7 Connection of Cables 7.1.2 Connection of Internal Cables Refer to Appendix B for the connection of internal cables. 7.2 Connecting External Cables 7.2.1 Connecting Optical Fiber
Note The optical fiber connectors of micro-BTS/remote stations are SC connectors. The ODF or optical connection box provided is equipped with FC connectors by default. If there are special requirements on the connectors, contact ZTE for customization. 7.2.1.1 Selecting Optical Fiber Different optical fibers are used for the connections between macro-/micro-BTS and remote stations. 1. If a remote station is near to a relative micro-BTS, optical fiber is used directly. The optical fiber adopts waterproof pigtail cable, and both ends are equipped with waterproof blockers and SC connectors. See Fig. 7.2-1 for the structure of the optical fiber. Optical fiber core wire (0.7m) SC/PC connector Waterproof blocker Single-mode waterproof pigtail cable Optical fiber core wire (0.7m) Fig. 7.2-1 Structure of Optical Fiber (1) 7-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual The core wires at both ends are 0.7m long. Both ends of the optical fiber can connect either a micro-BTS or a remote station. You can choose 10m/20m/50m/100m-long optical fiber for this connection based on the actual situation. 2. If an outdoor remote station is near to a relative indoor macro-BTS, optical fiber is used for connecting them directly. The optical fiber adopts waterproof pigtail cable, with both ends being SC connectors. In addition, one end is equipped with a waterproof blocker. See Fig. 7.2-2 for the structure of the optical fiber. Optical fiber core wire (3m) SC/PC connector Single-mode waterproof pigtail cable Waterproof blocker Optical fiber core wire (0.7m) Fig. 7.2-2 Structure of Optical Fiber (2) The core wires of the end equipped with a waterproof blocker are 0.7m long, and those of the other end are 3m long. The end with a waterproof blocker is to be connected with the remote station, and other end is used to connect the macro-BTS. You can choose 50m/100m-long optical fiber for this connection based on the actual situation. If a remote station is far from a relative macro-BTS and an ODF or optical connection box is required, two pieces of optical fiber should be used for connecting the macro-BTS with the ODF and the ODF with the remote station respectively. 3. 7-4 Chapter 7 Connection of Cables 1 Connection between the macro-BTS and the ODF The indoor-type optical fiber is adopted, with one end being SC/PC connectors and the other end being FC/PC connectors. See Fig. 7.2-3 for the structure of the optical fiber. SC/PC connector Single-mode optical fiber FC/PC connector Fig. 7.2-3 Structure of Optical Fiber (3) The SC/PC connectors are used to connect the macro-BTS, and the FC/PC connectors are used to connect the ODF. There is only one option for this connection: 30m-long optical fiber. 2 Connection between the ODF and the remote station The optical fiber adopts waterproof pigtail cable. The end equipped with a waterproof blocker uses SC/PC connectors, and the other end offers FC/PC connectors. See Fig. 7.2-4 for the structure of the optical fiber. Optical fiber core wire
(3m) SC/PC connector FC/PC connector Single-mode waterproof pigtail cable Waterproof blocker Optical fiber core wire
(0.7m) Fig. 7.2-4 Structure of Optical Fiber (4) 7-5 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual The core wires of the end equipped with a waterproof blocker are 0.7m long, and those of the other end are 3m long. The end with a waterproof blocker is to be connected with the remote station, and the other end is to be connected with the ODF. You can choose 50m/100m-long optical fiber for this connection based on the actual situation. Caution: If the ODF uses cubical connectors, contact ZTE in advance. 7.2.1.2 Laying Optical Fiber 1. Connecting optical fiber for a micro-BTS/remote station Because the end of the optical fiber for connecting a micro-BTS/remote station is equipped with a waterproof blocker, you need to remove the cover of the optical interface at the bottom of a micro-BTS/remote station first, insert the pigtail fiber into the cabinet, and then screw down the waterproof blocker into the optical interface, as shown in Fig. 7.2-5. Waterproof blocker Optical fiber Fig. 7.2-5 Schematic Diagram of Connecting Optical Fiber 2. Connecting optical fiber for a macro-BTS If the optical fiber is used to connect the Local Fiber Module (LFM) of a macro-BTS, first insert the optical fiber into an interface on the front panel of 7-6 Chapter 7 Connection of Cables the LFM, lay the optical fiber along the horizontal cabling trough on the top of the TRX layer, and then along the vertical cabling trough on the left of the shelf;
next, open the cover of the standby interface marked with BTM ANT on the top of the macro-BTS, pull the optical fiber out of the shelf and then lay it onto the cabling rack on top. 3. Requirements for laying optical fiber The optical fiber should be arranged in order, with the interval for cable ties less than 0.5m. The minimum bending radius of the outdoor-type optical fiber is 90mm, and that of the indoor-type optical fiber is 30mm. 7.2.2 Connecting Multi-carrier Interconnection RF Cables If a double-carrier & single-sector micro-BTS/remote station is required, two cabinets need be configured. These two cabinets should be connected by cables to achieve transmission of diversity antenna signals. When a micro-BTS cabinet and a remote station cabinet form a double-carrier &
single-sector micro-BTS system, two pieces of RF cables need be added to cross-connect the RFE-ANT0 interface with the EXTEND interface at the bottom of the two cabinets respectively. Similarly, when two double-carrier remote station cabinets form a double-carrier remote station and it is used in cooperation with a double-carrier macro-BTS, two pieces of RF cables need be added to cross-connect the RFE-ANT0 interface with the EXTEND interface at the bottom of the two cabinets respectively. Refer to Appendix B for the configuration of internal cables in a double-carrier system. The interconnection RF cable is 3m long, with both ends being RF N connectors. It is a finished product delivered with cabinets. It is named as F-RF05-009. See Fig. 7.2-6 for the cable connections between two cabinets. 7-7 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Micro-BTS/remote station EXTEND Remote station EXTEND RFE-ANT0 Interconnection RF cable (3m) RFE-ANT0 Fig. 7.2-6 Connection of Interconnection RF Cables 7.2.3 Waterproof Processing of Joints In case of double-carrier configuration, the joints between the sockets at the bottom of the cabinets and the connectors of the interconnection RF cables should be wrapped with waterproof adhesive tape. In addition, the joint between the socket at the bottom of a 20W micro-BTS (M802T micro-BTS) cabinet and the connector of the external fan cable should also be wrapped with the adhesive tape. You need to do the following:
1. Secure the relative connectors and sockets. 2. Implement waterproof processing to the joints. 1 Wrap the joints with the waterproof adhesive tape from the top of the connectors. The first layer should be wrapped in the same direction as for fastening the cable connectors. 2 Stretch the tape with force and wrap it circularly for three layers totally. Note that the next circle covers 1/2 of the previous circle, and the wrap stops at the position about 10cm away from the joint. 3 Grip the joint with force to make the tape stuck firmly with the joint. 7-8 Chapter 7 Connection of Cables 4 Wrap two layers of PVC tape around the waterproof adhesive tape in the same way as for wrapping the waterproof adhesive tape. 5 Finally wrap a layer of anti-ultraviolet tape. 7.2.4 Connection of Trunk Cables There are T1 interfaces at the bottom of the primary cabinet of a micro-BTS for connecting T1 cables (100-ohm coaxial cables), as shown in Fig. 7.2-7. T1 cable Fig. 7.2-7 Connection of T1 Cables 1. Select T1 cables. Micro-BTS can be installed outdoors, so PE-sheath T1 cables are used generally. If common T1 cables are used in an outdoor micro-BTS, PVC pipe should be added for protection. 2. Lay the T1 cables in order. Keep T1 cables and AC power cables separate with distance of more than 200mm. 3. When laying T1 cables on a tower, the space between two cable ties should be less than 0.5m to prevent friction with the tower upon swing of cables and avoid damage of T1 cable sheath. 7-9 8 Installation of Primary Antenna Feeder System
Summary
Describing the composition of the primary antenna feeder system.
Describing the procedures to install the primary antenna feeder system. 8.1 Preparations Before installing the primary antenna feeder system, check the qualification of the installation personnel for working at heights, installation environment, security measures, installation tools and system components, for the purpose of ensuring the successful installation. 8.1.1 Installation Personnel The antenna feeder system is installed by the professional installation personnel under the monitoring of the installation supervisor. The installation supervisor should be familiar with the materials, tools and operations for the installation, who is responsible for assigning suitable work for the installation personnel and recording the actual engineering data. The installation personnel should be skillful and healthy. Those who work at heights should have obtained the corresponding qualification, have no acrophobia, observe the security regulations, and have purchased the personal accident insurance. In addition, they are prohibited from drinking alcohol when working. 8-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 8.1.2 Installation Environment Check if the outdoor lightning grounding cable is well grounded and if its cross-section area is more than 50mm2. Check if the distance between the antenna pole and the lightning rod/lightning grounding point/outdoor cabling rack, the firmness and wind-resistant ability of the pole meet the design requirements. In addition, check if the necessary tools and assisting materials are prepared, and if the route for laying the primary feeder cables is determined through negotiation. The equipment provider presents the requirements on the installation of the antenna mount based on the structure and size of the antenna, and the network operator should install the antenna mount as required. The network operator is also responsible for the installation of the outdoor cabling rack, lightning rod, lightning grounding point and outdoor lightning grounding cable. Moreover, the network operator needs to drill holes on wall or rooftop for installing the feeder cable window as one of the equipment room conditions. 8.1.3 Security Measures
Caution The installation personnel working at heights must wear the safety belt, and those working on ground must wear the safety helmet. They must wear working clothes and shoes causing no slips when climbing up the tower. 1. Safety precautions should be stressed to the installation personnel. 2. The outdoor installation should be conducted in sunny days without strong wind. 3. Obvious signs should be set in the installation site to notify irrelative people to keep away from the site. The installation personnel working on ground are obligate to keep irrelative people, esp. children away from the site. The tools used on the tower and some metal components might slip to cause casualties, so they must be put in a canvas tool bag when not used, and the bag must be sealed immediately after you open it for a tool or component. 8.1.4 Installation Tools 1. Measurement tools: A compass, multimeter, inclinometer and tape measure;
2. Communication tools: Two mobile phones;
8-2 Chapter 8 Installation of Primary Antenna Feeder System 3. Raising tools: Pulley block and rope;
4. Special tools: Cutter for cutting primary feeder cables and tools for assembling connectors;
5. General tools: Adjustable wrench, sharp nose pliers, diagonal pliers, electrical knife, file and hacksaw;
6. Protection tools: Safety belt, safety helmet, safety rope, thick working clothes, RF prevention clothes, canvas tool bag, gloves, and multi-purpose sockets;
7. Other tools: Herringbone ladder and the wooden wheel axis for uplifting the primary feeder cable (which can be borrowed locally). 8.2 Composition and Installation Requirements of Antenna Feeder System 8.2.1 Composition The antenna feeder system is composed of antennae, antenna jumper cables, primary feeder cables, lightning arrester, jumper cables on top and grounding parts, as shown in Fig. 8.2-1. 8-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Lightning rod Antenna (2 sets) Jumper cable (1/2", 2 pieces) Lightning grounding kit Primary feeder cable (7/8", 2 pieces) Equipment room Lightning grounding kit Lightning arrester Lightning grounding kit Cabling rack Tower Jumper cable
(1/2", 2 pieces) Micro-
BTS Fig. 8.2-1 Typical Structure of the Antenna Feeder System 8-4 Chapter 8 Installation of Primary Antenna Feeder System 8.2.2 Technical Parameters 1. Height of antenna It depends on the networking plan. 2. Azimuth angle of antenna It depends on the networking plan. 3. Pitch angle of antenna It depends on the networking plan. Generally, it is between 0 and 10
(adjustable). 4. Pointing direction of antenna It depends on the azimuth angle of the antenna. Two antennae of the same sector must point to the same direction. 5. Distance between two diversity antennae Two antennae of one sector are diversity reception antennae to each other. They have the same height, but they should be distanced as much as possible. If the following formula is met, the installation requirement is met. d 10~20 (or H/d=11)d: Distance between two diversity antennae; H: Height from the antenna to the ground. If the carrier is 1.9GHz, the diversity distance should be more than 1.5m. If the carrier is 800MHz, the diversity distance should be more than 3.5m. 8.3 Installation Flow The antenna installation flow is as shown in Fig. 8.3-1. 8-5 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Start Determine the installation position Types of Antenna Directional antenna Assemble components of a directional antenna Raise/carry the antenna Secure the directional antenna Adjust the direction and pitch angle of the directional antenna Connect the antenna with the jumper cable and then seal their joint Omni antenna Raise/carry the antenna Secure the omni antenna Keep the omni antenna vertical Connect the antenna with the jumper cable and then seal their joint Fasten the antenna End Fig. 8.3-1 Antenna Installation Flow 8.4 Installation of Antenna
Caution:
1. Be cautious during the installation to prevent personal injury or equipment damage. 2. Measures should be taken to protect human body against the radiation when adjusting the antenna, for example, the installation personnel should wear the anti-radiation clothes. 8.4.1 Determining Installation Location The location for installing the antenna should be determined based on the engineering design drawing. If the actual location of the antenna mount is different from the engineering design, the installation engineers, customer representative and design unit should negotiate to complete the second design according to the requirements of the 8-6 Chapter 8 Installation of Primary Antenna Feeder System BTS on network coverage, space diversity, azimuth angle and pitch angle, thus ensuring desirable network coverage in future. 8.4.2 Installing Accessories of Directional Antenna Some fasteners need be installed on a directional antenna first. For example, the KATHREIN antenna need be installed with the fasteners 738516 and 737974. Before fastening the antenna, first install the fastener 737974 with angle adjustment setting onto the top and bottom of the antenna (as shown in Fig. 8.4-1), and then connect the fastener 737974 and the pole fastener 738516 with short bolts. During the installation, spring washers and flat washers are used. Please refer to the guide book delivered with the equipment for the information of specific fasteners to be used. Assemble the fasteners and angle adjustment accessories onto the antenna in advance before installing the antenna on the tower. Antenna pole 75mm 738 516 Connect them with two short bolts and nuts 737 974 Connect the antenna and the fastener with short bolts (spring washers and flat washers are added, and nuts are equipped with waterproof washers) After the connection, move the top of the antenna up and down to adjust the pitch angle Scale 0o ~ 16o KATHREIN 65 o Directional antenna After the connection, move the antenna right or left to adjust the azimuth angle 737 974 Fig. 8.4-1 Installation of the KATHREIN Antenna 8-7 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 8.4.3 Transporting and Raising Antenna
Caution:
Both the installation personnel working on tower and those working under tower should cooperate to raise the antenna onto the tower with rope. Note to keep the antenna away from the tower body to prevent any damage to the antenna when pulling it up the tower. Use rope and pulley block to raise the antenna, 3-m antenna jumper cable and other accessories (including tools, safety belt, adhesive tapes and cable ties) up to the tower platform, and then put them in a safe place to avoid falling. Note that the fasteners and other metal tools must be put in a canvas tool bag before pulling them up. When raising a directional antenna or an omni antenna, tie a knot at each end of the antenna to facilitate the cooperation between the installation personnel on and under the tower, as shown in Fig. 8.4-2. If an antenna is to be installed on the top of a building, carry the antenna and other accessories to the installation site manually. Pulley block Tie a knot with rope at each end of the antenna Pull the antenna away from the antenna to avoid damaging the antenna Rope for raising the antenna Fig. 8.4-2 Schematic Diagram of Raising the Antenna to the Tower Top 8-8 Chapter 8 Installation of Primary Antenna Feeder System 8.4.4 Installing and Adjusting Directional Antenna
Note:
The antennae of different providers require different installation modes. This section takes the installation of the KATHREIN antenna as an example. Before the installation, read the installation manual delivered with the antenna carefully. Install a directional antenna by the following steps:
1. Fastening the directional antenna onto the pole Fasten the fastener of the directional antenna with the pole. Do not screw the screws too tight or too loosely. If they are too loose, the antenna might fall off; if they are too tight, it is inconvenient to adjust the azimuth angle and pitch angle of the antenna later. 2. Adjusting the azimuth angle of the antenna 1 Measure the azimuth angle of the antenna with a compass. Then check the engineering design drawing for the antenna direction. 2 Adjust the orientation of the antenna by twisting it slightly, as shown in Fig. 8.4-1. At the same time, measure the orientation of the antenna with the compass. Keep adjusting until the deviation is within the design requirement, that is, less than or equal to 5 generally. 3 After the adjustment, fasten the fastener 738516 tight. 3. Adjusting the pitch angle of the antenna 1 Adjust the bubble inclinometer to the angle as required in the engineering design. 2 Adjust the pitch angle of the antenna slightly until the bubble of the inclinometer is located in the middle when you measure the pitch angle with it, as shown in Fig. 8.4-3. 3 After the adjustment, fasten the fastener 737974 tight. 8-9 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Fig. 8.4-3 Schematic Diagram of Adjusting the Pitch Angle of the Antenna 8.4.5 Installing and Adjusting Omni Antenna Install an omni antenna by the following steps:
1. Fasten the antenna (the part with jacket) onto the antenna mount with two fixing clips. Do not fasten it too tight or too loosely. If too tight, the jacket might be damaged; if too loosely, the requirements on weight-bearing and wind-resistant abilities cannot be met. 2. Check if the antenna is vertical. If so, fasten the antenna with the pole tight. 3. Protrude the antenna mount installed with the antenna out of the tower platform. Adjust the mount to make the antenna vertical. 8.4.6 Connecting Jumper Cable with Antenna and Sealing Their Joint
Note:
You can connect the jumper cable with the antenna and seal their joint before installing the antenna onto the pole, which can shorten the time for working at heights and reinforce the connection and waterproof performance of the joint. The operations are as follows:
1. Insert the jumper cable connector into the antenna interface and then screw them tight. 8-10 Chapter 8 Installation of Primary Antenna Feeder System 2. Implement waterproof processing to the joint between the antenna and jumper cable. 1) Wrap the joint with the waterproof adhesive tape from top download. The first layer should be wrapped in the same direction as for fastening the antenna jumper cable. 2) Wrap the waterproof tape circularly for three layers totally. Note that the next circle covers half of the previous circle, and the wrap stops at the position 10cm away from the joint. 3) Grip the joint with force to make the tape stuck firmly with the joint. 4) Wrap two layers of PVC tape around the waterproof adhesive tape in the same way as for wrapping the waterproof adhesive tape. 5) Finally wrap a layer of anti-ultraviolet tape. 8.5 Installation of Feeder Cable Window
Note:
The size of the feeder cable window provided by ZTE is 400mm400mm. It is a four-hole window and 12 pieces of feeder cables can pass through it. A 300mm300mm hole should be drilled on the wall for the installation of this feeder cable window. If a special feeder cable window is used, a hole should be drilled based on the actual size of it. No feeder cable window is needed when a micro-BTS is installed outdoors. The feeder cable window is usually installed on the outside wall of the equipment room, right between the indoor and outdoor cabling racks. If the primary feeder cable window is installed on the rooftop, you need to take measures to make it waterproof. For example, you can seal it with asphaltum or glass cement. The feeder cable window has four holes and can be connected with 12 pieces of feeder cables at most, as shown in Fig. 8.5-1. Follow the steps below to install a feeder cable window:
1. Determine the installation location based on the engineering design drawing. 2. Drill a hole on the wall according to the size of the feeder cable window used. 8-11 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 3. Drill holes for installing expansion bolts with a percussive drill, and then secure the main board of the feeder cable window with the expansion bolts. 4. 5. Install the sealing pad and gasket when leading the primary feeder cables into the equipment room. In cold and sandy places, install a wooden board in the equipment room to block sand blown by the wind and preserve heat. Fig. 8.5-1 Structure of a Feeder Cable Window 8.6 Connection of Feeder Cable This section describes how to assemble the 7/8 feeder cable connectors, how to connect the jumper cable & the primary feeder cable/antenna and seal their joint, and how to lay and fasten the feeder cables. The complete structure of a feeder cable of a micro-BTS/remote station is shown in Fig. 8.6-1. If a micro-BTS is installed outdoors and it is near to the antenna, the 1/2 feeder cable can be used for the primary feeder cable. 8-12 Chapter 8 Installation of Primary Antenna Feeder System Antenna jumper cable Label Feeder cable Label Customized jumper cable on top Male N connector Fig. 8.6-1 Structure of the Feeder Cable of a Micro-BTS/Remote Station 8.6.1 Determining Route for Feeder Cable The cabling route of the feeder cables should be determined according to the engineering design drawing. If an alteration is necessary, negotiate with the customer representative for solution. Note that the primary feeder cables should be as short as possible. 8.6.2 Assembling Connectors of Primary Feeder Cable
Caution:
Assembling feeder cable connectors is the most important procedure in the installation of the antenna feeder system, for the quality of them directly affects the performance of both equipment and network. Be cautious when using the cutter, for it is very sharp. This section describes how to assemble connectors for the ROSENBERGER 7/8 feeder cable. For the assembly of connectors for other types of feeder cable or feeder cable of other manufacturers, refer to the specific installation manual. 8-13 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 1. The cutter used is shown in Fig. 8.6-2. Fig. 8.6-2 Cutter for Assembling 7/8 Feeder Cable Connectors 2. Pull the feeder cable straight (about 150mm long) at the end to be installed with a connector, and then strip 50mm-long sheath off the cable with the cutter. 3. Put the feeder cable on the trough of the cutter EASIAX, reserve four corrugations at the end of the blade, and then press down the handle. The main blade should point to one wave crest. 4. Screw to shut the cutter closely. In this way, the internal and external copper conductors of the feeder cable are severed, and at the same time the cable sheath is severed by the assisting blade, as shown in Fig. 8.6-3. Fig. 8.6-3 Schematic Diagram of Cutting the Feeder Cable with the Cutter 5. Check if the cutting position is correct, as shown in Fig. 8.6-4. Wave crest Fig. 8.6-4 Schematic Diagram of Correct Cutting Size 8-14 Chapter 8 Installation of Primary Antenna Feeder System 6. Disassemble the feeder cable connector into two parts: front part and back part. And then insert the feeder cable into the back part until it contacts the first corrugation of the cable. 7. Insert the tube expander of the cutter into the feeder cable and then screw left and right to expand the external copper conductor, as shown in Fig. 8.6-5. Fig. 8.6-5 Schematic Diagram of Expanding the External Copper Conductor 8. Check if there are copper bits left in the conductor and if the conductor is expanded evenly. Pull the back part of the connector with force to check if it is connected firmly with the cable. If any requirement cannot be met, redo the above steps. 9. Connect the front part with the back part, as shown in Fig. 8.6-6. Fig. 8.6-6 Schematic Diagram of Connecting the Front Part with the Back Part of the Connector 10. Clamp the front part of the connector with a wrench and use another wrench to clamp the back part. Twist the back part but keep the front part unmoved until they are connected firmly. 8-15 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Twist this wrench only Keep this wrench immovable Fig. 8.6-7 Schematic Diagram of Fastening the Front Part with the Back Part of the Connector 8.6.3 Cutting Feeder Cable
Caution:
Stick temporary labels at both ends of the primary feeder cables after cutting them. Labels can also be stuck in the middle part of the feeder cables but they must be the same; otherwise, wrong connections might be caused. On the installation site, measure the cabling route of the primary feeder cables accurately and then cut the cables as needed. The operations are as follows:
1. When the antenna feeder system is to be installed on the top of a building:
1) Measure the cabling route with a tape measure to determine the length of the primary feeder cables needed by each sector. 2) Add some margin (1m~2m) to the measured lengths when cutting the cables. 3) After cutting a piece of primary feeder cable, stick temporary labels at both ends of the cable, for example, ANT1, ANT2, ANT3, ANT4, ANT5, ANT6. 4) Carry the feeder cables having been cut to the top of the building. Ensure that the cables are not squeezed or damaged during the conveyance. 2. When the antenna feeder system is to be installed on a tower:
1) Pull one end of the feeder cable to the tower top with the roller support, pulley block and rope. Then the installation personnel under the tower cut the cable based on the length needed (with a certain margin). Stick a temporary label at 8-16 Chapter 8 Installation of Primary Antenna Feeder System the lower end of the cable. Stick a formal label after the cable is led into the equipment room. 2) Assemble the connectors before raising the primly feeder cables, thus shortening the time for working at heights and ensuring the quality of the connectors. 8.6.4 Raising Primary Feeder Cable When the antenna feeder system is to be installed on a tower, the pulley block will be used to raise the primary feeder cables, as shown in Fig. 8.6-8. The operations are as follows:
1. Check the labels at both ends of the primary feeder cable to ensure that it is the right cable. 2. Wrap the feeder cable connector with a piece of flax cloth or an antistatic plastic bag filled with foam, and then bundle it tight. 3. Tie a knot with the rope on the feeder cable at the place 0.4m away from the connector and then another knot about 3.4m away from the connector, for the purpose of facilitating the cooperation between the installation personnel on and under the tower to raise the cable and preventing the feeder cable and its connector from being damaged due to hit with the tower. 4. After the primary feeder cable is pulled to the tower top, fasten it tight.
Caution:
Raise the primary feeder cable with care to avoid damaging the sheath of it. If not, the whole piece of the cable will be wasted. Mind your own safety also when raising the cable. 8-17 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Pulley block The feeder cable connector is wrapped Label Tie a knot with the rope on the feeder cable at the place 0.4m away from the connector and then another knot about 3.4m away from the connector Use this rope to pull the feeder cable away from the tower to prevent damaging the cable and the connector when raising the cable The rope for pulling the cable up the tower Fig. 8.6-8 Schematic Diagram of Pulling the Feeder Cable Up the Tower 8.6.5 Laying and Fastening Primary Feeder Cable 1. Cabling principles 1) The primary feeder cables should be laid in order on the cabling rack after being led into the equipment room through the feeder cable window. 2) The primary feeder cables should be laid without crossings along the outdoor cabling rack and the cabling ladder of the tower. 3) Be familiar with the cabling route of the primary feeder cables and draw it on paper in advance to ensure there are no crossings during the actual cabling. 8-18 Chapter 8 Installation of Primary Antenna Feeder System 4) The minimum bending radius of the primary feeder cable should be no less than 20 times of its semi-diameter. The minimum one-time bending radius is 90mm, and the minimum repeated bending radius is 200mm. 5) The maximum interval between hangers is 1.65m. 2. Cabling procedures:
1) In principle, a hanger should be installed on the tower or cabling rack every about 1.5m. For onsite installation, the interval can be lengthened or shortened depending on the actual situation, but the maximum interval cannot exceed 1.65m. Install the hangers with even distance in the same direction. If two rows of hangers are installed on one cabling ladder, keep them in parallel and in order. See Fig. 8.6-9 for the appearance of a hanger. Fig. 8.6-9 Appearance of a Hanger 2) Arrange the primary feeder cables before leading them into the equipment room. 3) Fasten the primary feeder cables from top downward with hangers. Keep the cables straight all the way. Do not fasten the feeder cables at both ends simultaneously. 4) If the antenna feeder system is installed on the top of a building, the network operator should install the cabling ladder on the wall. In this case, fasten the primary feeder cables with hangers along the ladder before leading them into the equipment room. 8-19 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 8.6.6 Connecting Jumper Cable with Feeder Cable and Sealing Their Joint
Caution:
Pay attention to the sealing of the joint between the feeder cable and the jumper cable, which is critical in the installation of the antenna feeder system. Use waterproof adhesive tape for the sealing. Generally, the 3m-long 1/2 jumper cable is used to connect the antenna and the primary feeder cable. Connect the 1/2 jumper cable with the primary feeder cable and then seal their joint as follows:
1. Connect the antenna jumper cable with the connector of the primary feeder cable and then screw down the connector. 2. Treat connectors with waterproof measures. The procedures are as follows:
1) Wrap the waterproof adhesive tape around the joint from the sunk area upward
(fill the area with the tape), as shown in Fig. 8.6-10. Fig. 8.6-10 Schematic Diagram of Wrapping Waterproof Adhesive Tape (1) 2) Stretch the tape with force and wrap it in the same direction as for fastening the cable connector. 3) Wrap circularly in the reverse direction for the second layer, as shown in Fig. 8.6-11. Note that the next circle covers 1/3 of the previous circle for the purpose of preventing inleakage of rain. Wrap the joint for three layers totally. Do not cut the adhesive tape during the wrapping. The length of the cable wrapped with the tape should be 20mm longer than that of the connector. 8-20 Chapter 8 Installation of Primary Antenna Feeder System Fig. 8.6-11 Schematic Diagram of Wrapping Waterproof Adhesive Tape (2) 4) After the wrapping, grip the joint with both hands to make the tape stuck tight with the joint, as shown in Fig. 8.6-12. Fig. 8.6-12 Schematic Diagram of Wrapping Waterproof Adhesive Tape (3) 5) Wrap two layers of PVC tape around the waterproof adhesive tape. Note that the next circle covers half of the previous circle. 6) Grip the joint again. 7) Use ties to fasten the wrapped part at both ends to prevent the tape from falling off due to aging. 8.6.7 Leading Primary Feeder Cable into Equipment Room 1. Precautions 1) See Fig. 8.6-13 and Fig. 8.6-14 for the modes of leading the primary feeder cables into the equipment room. It must be ensured that no rainwater will be led in along the feeder cable. If necessary, the water-blocking curve can be made. 8-21 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Feeder cable window One-time bending, with the min. radius of more than 90mm Indoors Outdoors Cabling rack Hanger Fig. 8.6-13 Leading the Feeder Cable into the Equipment Room - Mode 1 Cabling rack Hanger One-time bending, with the min. radius of more than 90mm Indoors Feeder cable window Outdoors Fig. 8.6-14 Leading the Feeder Cable into the Equipment Room - Mode 2 2) The feeder cables are led into the equipment room through the feeder cable window. The outdoor and indoor cabling racks are used for leading them. 2. Procedures 1) Loosen the fasteners on the feeder cable window and remove the cover from the holes. 2) Lead the feeder cables into the equipment room. Two people in and out of the room respectively should cooperate when leading the cables to prevent damaging both the equipment and the cable. Screw down the fastening hoop after the feeder cables are pulled in position. 3) Cut the feeder cables. The following should be done before cutting them:
8-22 Chapter 8 Installation of Primary Antenna Feeder System
Checking labels Check if the temporary labels are stuck on the cables. Without the labels, you might misconnect the cables.
Determining the cutting position Determine the cutting position based on the installation position of the shelf and the lightning arrester, length of jumper cable on top, and the bending radius of the feeder cables. 4) Assemble the indoor connectors of the primary feeder cables. 8.6.8 Connecting Indoor Jumper Cable The indoor jumper cable on top is connected between the primary feeder cable and the antenna interface at the bottom of a micro-BTS. Customize a jumper cable on site based on the actual situation. One end of the jumper cable is a male N connector, which is directly connected to the bottom of the cabinet. The other end is a female DIN connector, which is connected to the 7/8 primary feeder cable. See Fig. 8.6-1. 8.7 Grounding System of Micro-BTS Grounding aims to protecting both the human being and the equipment against lightning shock and electromagnetic interference. The grounding system of a micro-BTS includes protection grounding on the chassis, lightning arrester for RF components in the cabinet, for GPS antenna, for T1 cables, for 120V AC power and for feeder cable grounding kit. 1. Grounding principles of primary feeder cables 1) Generally, each primary feeder cable should be grounded at least three times for lightning protection, that is, on the tower platform, between the tower and the outdoor cabling rack, and on the wall before the feeder cable is led into the equipment room. If the primary feeder cable is more than 60 meters long, a lightning grounding kit should be installed every 20 meters. If the primary feeder cable is shorter than 5m, one grounding point is enough. If the feeder cable is shorter than 20m but longer than 5m, it can be grounded at two points. 2) The antenna feeder system, antenna mount and newly-installed cabling rack should all be welded to the lightning protection net of the building. The feeder 8-23 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual cables should also be grounded at three points, that is, on the antenna pole, on the rooftop, and on the wall before the cables are led into the equipment room. 3) Before leading the primary feeder cable along the outdoor cabling ladder from the top of the building to the equipment room, check whether the cabling ladder is grounded. If not, request the network operator to accomplish it as soon as possible. 2. Procedures to install the grounding kit
Caution:
It is prohibited to install the grounding kit in thunderstorm weather;
otherwise, the installation personnel might be hurt. When installing the grounding kit, be sure to keep the feeder cable at the joint straight. 1) Prepare such tools as paper knife, straight screwdriver, spanner and sharp nose pliers. 2) Choose a suitable position for installing the grounding kit, and cut the sheath off the 7/8" feeder cable based on the size of the grounding kit. The structure of a grounding kit is shown in Fig. 8.7-1. Grounding terminal Grounding cable Feeder cable Grounding wire clip Out-layer copper core of feeder cable Sheet copper of feeder cable Fig. 8.7-1 Structure of a Grounding Kit 3) Lead the grounding cable of the lightning grounding kit to the grounding net. Keep the angle between the grounding cable and the primary feeder cable no more than 15. 8-24 Chapter 8 Installation of Primary Antenna Feeder System If the antenna feeder system is installed on a tower, lead the grounding cable downward along the tower. If the antenna feeder system is installed on the top of a building, lead the grounding cable to the lightning protection net. 4) Before installing the grounding kit, wrap the waterproof adhesive tape around the grounding cable near the grounding copper for sealing, as shown in Fig. 8.7-2. Fig. 8.7-2 Schematic Diagram of Wrapping Waterproof Adhesive Tape Around the Grounding Cable 5) Clamp the external conductor with the grounding copper and clip tightly. 6) Seal the joint between the grounding kit and the feeder cable as follows:
First wrap the waterproof adhesive tape and then the PVC tap around the joint.
Wrap the waterproof adhesive tape circularly from bottom upward, and then from top downward, finally from bottom upward again. Note that the next circle covers half of the previous circle. 7) Connect the grounding terminal of the grounding kit to the tower body or the cabling rack on the top of the building (the cabling rack is connected to the lightning protection net). Remove the paint and oxide at the junction within the radius of 13mm and then coat the clean area with antioxidant cream. After the connection, paint the area with antirust paint. 8) Before the primary feeder cable is led into the equipment room, connect the grounding terminal of the grounding kit to the outdoor grounding busbar. 8-25 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 8.8 Test of Antenna Feeder System 1. After the antennae are installed and all feeder cables are connected, measure the standing wave ratio of them. 2. Measure one end of the indoor 1/2 jumper cable, which is to be connected with the cabinet, with the tester. The standing wave ratio should be lower than 1.5. It is best to be lower than 1.3. 3. Record the Voltage Standing Wave Ratio (VSWR) value and provide the VSWR testing diagram. 8.9 Waterproof Processing of Connectors Follow the steps below to seal the joints between two cables:
1. Fasten the relative joints. 2. Implement waterproof processing to the joints. 1) Wrap the joints with the waterproof adhesive tape from the top of the connectors. The first layer should be wrapped in the same direction as for fastening the cable connectors. 2) Stretch the tape with force and wrap it circularly for three layers totally. Note that the next circle covers half of the previous circle, and the wrap stops at the position about 10cm away from the joint. 3) Grip the joint with force to make the tape stuck firmly with the joint. 4) Wrap two layers of PVC tape around the waterproof adhesive tape in the same way as for wrapping the waterproof adhesive tape. 5) Finally wrap a layer of anti-ultraviolet tape. 8-26 9 Installation of GPS Antenna Feeder System
Summary
Describing the composition of the GPS antenna feeder system.
Describing the procedures to install the GPS antenna feeder system. 9.1 Preparations 9.1.1 Installation Personnel Before installing the GPS antenna feeder system, check the qualification of the installation personnel for working at heights, installation environment, security measures, installation tools and system components. The antenna feeder system is installed by the professional installation personnel under the monitoring of the installation supervisor. The installation supervisor should be familiar with the materials, tools and operations for the installation, who is responsible for assigning suitable work for the installation personnel and recording the actual engineering data. The installation personnel should be skillful and healthy. Those who work at heights should have obtained the corresponding qualification, have no acrophobia, observe the security regulations, and have purchased the personal accident insurance. In addition, they are prohibited from drinking alcohol when working. 9.1.2 Installation Environment Check if the outdoor lightning grounding cable is well grounded and if its cross-section area is more than 50mm2. Check if the distance between the antenna pole and the 9-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual lightning rod/lightning grounding point/outdoor cabling rack, the firmness and wind-resistant ability of the pole meet the design requirements. In addition, check if the necessary tools and assisting materials are prepared, and if the route for laying the primary feeder cable are determined through negotiation. The equipment provider presents the requirements on the installation of the antenna mount based on the structure and size of the antenna, and the network operator should install the antenna mount as required. The network operator is also responsible for the installation of the outdoor cabling rack, lightning rod, lightning grounding point and outdoor lightning grounding cable. Moreover, the network operator needs to drill holes on wall or rooftop for installing the feeder cable window as one of the equipment room conditions. 9.1.3 Security Measures
Caution:
The installation personnel working at heights must wear the safety belt, and those working on ground must wear the safety helmet. They must wear working clothes and shoes causing no slips when climbing up the tower. 1. Safety precautions should be stressed to the installation personnel. 2. The outdoor installation should be conducted in sunny days without strong wind. 3. Obvious signs should be set in the installation site to notify irrelative people to keep away from the site. The installation personnel working on ground are obligate to keep irrelative people, esp. children away from the site. The tools used on the tower and some metal components might slip to cause casualties, so they must be put in a canvas tool bag when not used, and the bag must be sealed immediately after you open it for a tool or component. 9.1.4 Installation Tools 1. Measurement tools: A compass, multimeter, inclinometer and tape measure;
2. Communication tools: Two mobile phones;
3. Raising tools: Pulley and rope;
4. Special tools: Cutter for cutting primary feeder cables and tools for assembling connectors;
9-2 Chapter 9 Installation of GPS Antenna Feeder System 5. General tools: Adjustable wrench, sharp nose pliers, diagonal pliers, electrical knife, file and hacksaw;
6. Protection tools: Safety belt, safety helmet, safety rope, thick working clothes, RF prevention clothes, canvas tool bag, gloves, and multi-purpose sockets;
7. Other tools: Herringbone ladder and the wooden wheel axis for uplifting the primary feeder cable (which can be borrowed locally). 9.2 Composition of GPS Antenna Feeder System See Fig. 9.2-1 for the composition of the GPS antenna feeder system. GPS antenna Coaxial cable Fixing clip Sleeve Micro-
BTS Fig. 9.2-1 Composition of the GPS Antenna Feeder System 9.3 Installation Procedures As the CDMA clock and frequency reference, GPS plays a very important role. The GPS antenna receives navigation and position signals of GPS satellites, demodulates frequency and clock signals through a GPS signal receiver and provides these signals to related elements of CDMA BTSs. 1. Requirements on GPS antenna installation The GPS antenna should be installed in an open and high place, so that it can trace more satellites, for example, on the top of a building or on a tower. Make the GPS feeder cable as short as possible to minimize the attenuation. The GPS antenna should be installed in the lightning protection area of the tower; otherwise, a lightning rod should be customized and installed for the GPS antenna. 9-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 2. Assembly of a GPS coaxial cable connector 1) Strip the a segment of sheath off the GPS coaxial cable as required in Fig. 9.3-1. 6.2 16.7 Fig. 9.3-1 Schematic Diagram of Length of Cable Sheath to be Stripped 2) Assemble the components onto the cable as shown in Fig. 9.3-2. And then solder the core wire with the pin. Unfold the shielding layer and wrap it around the bushing. Pin Soldering tin Cable core wire Insulating washer Bushing Cable shielding Crimping tube Nut Cable Fig. 9.3-2 Schematic Diagram of Soldering the Core Wire with the Pin 3) Assemble the components into the shell, as shown in Fig. 9.3-3. Pin Shell Insulating washer Bushing Crimping tube Nut Fig. 9.3-3 Structure of N-J7A 3. Procedures to install the GPS antenna feeder system 1 Assemble an outdoor coaxial cable connector following the same steps mentioned above. 9-4 Chapter 9 Installation of GPS Antenna Feeder System 2 Insert the connector through the sleeve (a GPS accessory), and then lay the coaxial cable from the GPS antenna to the GPS lightning arrester. 3 Screw to connect the outdoor coaxial cable connector with the GPS antenna connector. 4 Screw the sleeve onto the GPS antenna, keeping the GPS antenna unmoved. 5 Secure the tube on the antenna pole with a fixing clip. 6 Cut the coaxial cable based on the installation position of the GPS lightning arrester. Assemble the indoor cable connector and then connect it with the lightning arrester. Do not wrongly connect the equipment terminal and antenna feeder terminal of the GPS lightning arrester. 7 Lay the coaxial cable from the GPS lightning arrester to the GPS port of a micro-BTS. 9.4 Test of Antenna Feeder System 1. After the antennae are installed and all feeder cables are connected, measure the standing wave ratio of them. 2. Measure one end of the indoor 1/2 jumper cable, which is to be connected with the cabinet, with the tester. The standing wave ratio should be lower than 1.5. It is best to be lower than 1.3. 3. Record the VSWR value and provide the VSWR test diagram. 9-5 10 Installation of Internal Modules
Summary
Describing the modules in a micro-BTS/remote station.
Describing the functions of the modules.
Describing the flow of installing the modules. 10.1 Overview 10.1.1 Logical Positions of Equipment Modules The modules micro-BTS are positioned as shown in Fig. 10.1-1. and boards in M800T/M801T/M802T/M190T/M191T/M192T B R F S E1 BRFS BDM MTRX MPA MLNA RX0 RX1 TX M P D M D I V M L N A 1 M L N A 2 M P A M D U P RFE-ANT0 RFE-ANT1 BGPS MGPS 10M/12M ANT Door Fig. 10.1-1 Modules and Boards in M800T/M801T/M802T/M190T/M191T/M192T Micro-BTS 10-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual The modules and boards in R800T/R801T/R802T/R190T/R191T/R192T remote stations are positioned as shown in Fig. 10.1-2. RFM Optical fiber BRFS MTRX MPA MLNA RX0 RX1 TX M P D M D I V M L N A 1 M L N A 2 M P A M D U P RFE-ANT0 RFE-ANT1 Door Fig. 10.1-2 Modules and Boards in R800T/R801T/R802T/R190T/R191T/R192T 10.1.2 Layout of Internal Modules A ZXCBTS micro-BTS is composed of Micro Transmitter & Receiver (MTRX) module, Micro Low Noise Amplifier (MLNA) module, Baseband Digital Module
(BDM) module, Micro GPS (MGPS) module, Micro-BTS Power Distribution (MPD) 400W module, DIVersity (DIV) module, DUPlexer (DUP) module and Micro Power Amplifier (MPA) module, as shown in Fig. 10.1-3. 10-2 Chapter 10 Installation of Internal Modules 1 MTRX 2 BDM 3 MPD400W 4 DIV 5 MLNA 6 MPA 7 Heater 8 DUP 9 MGPS Fig. 10.1-3 Layout of Modules in a ZXCBTS Micro-BTS A ZXCBTS remote station is composed of MTRX module, MLNA module, Remote Fiber Module (RFM), MPD 400W module, DIV module, DUP module and MPA module, as shown in Fig. 10.1-4. 10-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 1 MTRX 2 RFM 3 MPD400W 4 DIV 5 MLNA 6 MPA 7 Heater 8 DUP Fig. 10.1-4 Layout of Modules in a ZXCBTS Remote Station 10.1.3 Functions of the Modules The following modules and accessories need be installed:
1. BDM BDM is the core module of a ZXCBTS micro-BTS, which completes the modulation & demodulation of baseband data, signaling processing, resources management and operation & maintenance functions. 2. MTRX MTRX provides interfaces to BDM and sends transmitted or received basedband data as well as the information on configuration, control, status and alarms. It achieves up conversion, intermediate frequency bandpass filter, transmit link gain control and signal amplification on forward it links. Moreover, 10-4 Chapter 10 Installation of Internal Modules accomplishes down conversion, signal amplification and bandpass filter on reverse links. MTRX800 is used in M800T/M802T micro-BTS/remote stations, whereas M190T/M191T/M192T micro-BTS/remote stations adopt MTRX190. 3. MPA MPA receives CDMA signals transmitted by MTRX and then amplifies the power of the signals, which are finally emitted to a cell through the antenna after being processed by a duplexer filter. M800T micro-BTS/remote stations adopt MPA800; M802T micro-BTS/remote stations adopt MPA802; M190T/M191T micro-BTS/remote stations adopt MPA190T; M192T micro-BTS/remote stations adopt MPA192. 4. RFE Receive Front Element (RFE) consists of MDUP (Duplex), MDIV (Diversity) and MLNA. On reverse links, the signals received by the antenna are filtered by the duplexer filter and then amplified. On forward links, the signals outputted by MPA are filtered by the duplexer filter and then emitted to the cell through the antenna. 5. MPD MPD directly converts the 120V AC power into the power with suitable voltage and supply the power to all modules in a micro-BTS/remote station. Moreover, it controls the heater in a micro-BTS/remote station to maintain the internal environment stable. It also supports the monitoring of the power supply status. 6. Optical interface module There are two kinds of optical interface modules used: OIM and RFM, which are respectively installed in a micro-BTS and a remote station. They accomplish the following functions:
1 Connecting BDS and RFS, providing channel for multiplexing and forward/reverse data and signaling, and carrying out demultiplexing optical-electrical conversion. 10-5 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 2) Multiplexing and demultiplexing LVDS signals. 3) Providing 12MHz (800MHz) or 10MHz (1.9GHz) analog signals to the RF subsystem. 4) Measuring the transmission delay of LFM (OIM) and RFM, and reporting the signal to RF Control Module (RFCM) through Integrated Circuit Interface Circuit (IIC) bus CM to compensate the transmission delay on Channel Processing Module (CHM). 5) Reporting the alarm signals about temperature, humidity, and access control generated in a remote station to RFCM. 6) Offering communication links between MPA and RFCM. 7) Monitoring important signal, for example, 16chip. 7. GPSTM GPSTM functions in providing 16chip or pp2s clock signal, 10MHz reference signal and TOD messages. 10-6 Chapter 10 Installation of Internal Modules 10.2 Module Installation Flow Start Install MTRX Micro-BTS Remote station Install BDM Install RFM Install MGPS Install MPA Install DUP Install DIV Install MLAN Install MPD400W Based on the configuration Install the heater Installation check End Fig. 10.2-1 Module Installation Flow Diagram 10-7 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 10.3 Installation and Replacement of Modules
Note The modules and cables in Micro-BTS/remote stations have been installed, connected and tested before delivery. Before commissioning, you only need to check if they are loose due to conveyance. According to the configuration requirement, you might need to add optical fiber modules or CSM5000 expansion modules in the expansion slots of the corresponding BDM board. If any fault occurs, the maintenance personnel can refer to this manual for simple maintenance. 10.3.1 Installation Sequence
Note This section describes the sequence of module installation and cable connection in an M800 micro-BTS. Refer to this sequence for the installation in M801T/M802T/M190T/M191T/M192T/R800T/R190T/R191T/R192T micro-BTS. 1. 2. Install MTRX, BDM and BRFS. Install T1 lightning arrester and lay T1 cables. 3. Connect Terminal B of DCDX02 and RSTDX to MPA and BRFS respectively, and bundle the cables with cable ties on the cable tie bases. 4. Install MPD, BGPS, MGPS, MDIV, MLNA, MPA, RF and GPS lightning arrester. 5. Lay interconnection cables between modules, access control cable and door grounding cable, and connect the antistatic wrist strap. 6. Connect Terminal B of the RF cable RF27 to MDUP_ANT loosely. Next, install MDUP in the cabinet and then fasten it. Finally, connect the other two RF connectors on MDUP. 7. Install the heater, power lightning arrester and connect the relative cables
(including ACDX01). 10.3.2 Table of Cable Connections Refer to Appendix B. 10-8 Chapter 10 Installation of Internal Modules 10.3.3 Fastening and Bundling of Internal Cables 1. Fastening coaxial cables For semi-rigid coaxial cables, connect both ends to the corresponding terminals firmly. 2. Bundling of GPS-BDM conductive wires and RF cables RF29/RF30 See Fig. 10.3-1. BGPS GPSTM 307.5+0.1 B R F S BDM M D I V M L N A
1 M L N A
2 M P D M P A M T R X A M D U P GPS-BDM RF30 RF29 To Terminal A Bundle of cables T-shape hole Cable tie Fig. 10.3-1 Schematic Diagram of Bundling Internal Cables (1) Bundle the cables RF29 and RF30 on the door and the grounding cable of the antistatic wrist strap in the inner side of the bundling plank, while bundle the GPS-BDM cables in the outer side of it, as shown in Fig. 10.3-2. 10-9 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual GPS-BDM cable RF30 RF29 Cable tie Bundling plank Fig. 10.3-2 Schematic Diagram of Bundling Internal Cables (2) 3. Bundling of DCDX01, DCDX02, RSTDX, MONDX01 and MONDX02 cables Bundle the cables DCDX01, DCDX02, RSTDX, MONDX01 and MONDX02 with cable ties on the cable tie bases, as shown in Fig. 10.3-3. DCDX01 RSTDX DCDX02 Cable tie base B R F S BDM M T R X Cable tie base M D I V M L N A
1 M L N A
2 M P D M P A E1 cable M D U P MONDX02 MONDX01 Fig. 10.3-3 Schematic Diagram of Bundling Internal Cables (3) 10-10 Chapter 10 Installation of Internal Modules 4. Cabling of T1 cables in the cabinet The T1 lightning arrester is equipped with two T1 cables. Before connecting the T1 lightning arrester with the cabinet, label the T1 cables at the position near the connectors with OUT# or IN# (#=1, 2, 3 or 4). OUT# and IN# should be the same as OUT or IN marked on the cable outlets at the back of the lightning arrester. When installing the T1 lightning arrester, ensure that the serial number # marked on the T1 cables is consistent with the silk-screen at the bottom of the BDM and the cabinet. To facilitate recabling the T1 cables connected with the lightning arrester, these T1 cables should be laid along the upper edge inside the cabinet, and the cable tie bases should be installed at the positions convenient for uninstallation. See Fig. 11-8. It is suggested to bundle the T1 cables with cable ties every 150mm. 10.3.4 Installation of OIM If a micro-BTS need be configured as a remote station, an OIM should be added on the BDM of the micro-BTS. See Fig. 10.3-4 for the corresponding relations between the OIM expansion slots in BDM and the sectors. X27 X17 X18 sector sector sector X26 X15 X16 Fig. 10.3-4 Corresponding Relations between OIM Expansion Slots in BDM and Sectors 10-11 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual When inserting the OIM into the BDM, make the interface of the optical module on the OIM face outward to ensure that optical fibers can be inserted into the optical module of the OIM from the right side of the BDM, as shown in Fig. 10.3-5. BDM OIM Optical interface facing outward OIM slot Fig. 10.3-5 Schematic Diagram of Inserting the OIM into the BDM 10.3.5 Installation of LFM If a remote station need be configured for a macro-BTS, it is only necessary to replace TRX of a sector with LFM by just inserting LFM into the TRX slot in the TRX layer of the macro-BTS without changing any cable connections on the backplane. The RF modules such as TRX, HPA and RFE need not be installed in the macro-BTS. Refer to 7.2.1 Connecting Optical Fiber for the connection with LFM and the cabling of optical fibers in a macro-BTS. 10.4 Points for Attention 1. Main tool: Philips screwdriver. 2. When installing MPA and MPD400W, cover MPA/MPD400W and the main radiator with silicon. the place between the 3. The modules should be installed firmly and reliably. 10-12 11 Hardware Installation Check
Summary
Describing the hardware installation check items 11.1 Checking Components in the Cabinet Check if:
1. The RF cables between the modules are connected correctly and firmly. 2. The bolts of all modules are screwed down to ensure reliable connections between the modules and the backplane. 3. The unused connectors are screwed with matching terminals. 4. The RF cables are not cross-connected or pulled too tight. Some margin is reserved at the turning corner and the connectors are connected firmly. 11.2 Checking the Cabinet Check if:
1. The installation position of the cabinet complies with the design requirement. 2. After the shelf is fixed, it is stable enough to resist earthquake of 7 in Richter scale. 3. No part of the shelf is loose or damaged. The shelf is well painted and the indications on the shelf are complete, correct and clear. 4. No metal scraps or useless wires are left in the cabinet. 5. All bolts are screwed down, and flat washers and spring washers are installed without inversion. 11-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 6. The cable outlet at the bottom of the cabinet has been covered with the cover plate after the cables are connected. 7. The combined cabinets are arranged in order and the connecting pieces on the top of the cabinets are fastened firmly. 8. The surface of the cabinet is clean, the paint has no blemishes, and various indications on the surface are correct, clear and complete. 9. The front door can be opened or closed flexibly. 11.3 Checking Cables Check if:
1. All cables are laid straight and there are no cross-connections. Surplus cables are coiled, bundled and put in the cabling trough. 2. The cables are turned smoothly. 3. Power cables and signal cables are laid separately with a distance of more than 150mm. 4. All cables are labeled clearly at both ends to avoid wrong or missed connections. 5. The joints are reliable and well contacted without breaks or bends. 6. The cables are tied with proper tightness, and the cable ties are distanced evenly. 7. Surplus part of the cable ties for indoor cables has been cut. 8. Some margin is reserved when the cable ties used on outdoor cables are cut. 9. No cable tie has spininess part after being cut. 10. All cables are stuck with labels indicating the usage, and the contents in the labels at both ends are the same. 11. Stick the labels with transparent adhesive tape to prevent them from falling off. 11.4 Checking Power Cables and Grounding Cables Check if:
1. The cabling of power cables and grounding cables conforms to the design requirements. 11-2 Chapter 11 Hardware Installation Check 2. The PGND cable of the micro-BTS adopts the olivine or yellow copper-core cable with the cross-section area of 35mm2, which is connected to the indoor PGND copper busbar reliably. The GND/BGND cable adopts the black copper-core cable with the cross-section area of 25mm2. The -48V power cable adopts the blue copper-core cable with the cross-section area of 25mm2. All these cables are laid straight and connected reliably. 3. The grounding bus wire is directly connected to the indoor grounding busbar. The cross-section area of the grounding bus wire is more than 50mm2. 4. Each terminal of the grounding copper busbar is connected with only one device. 5. PGND cables and AC neutral cables are laid separately. 6. AC neutral cables are grounded independently in the power room. 7. The indoor grounding resistance is less than 5 ohm. 8. Each cable is marked correctly and clearly. 9. Power cables are not bundled with other cables but separately. 10. The surplus part of the grounding and power cables are cut. 11. The copper lugs at both ends of power cables and grounding cables are welded or crimped well. 12. There is no joint (between two pieces of cables) for a piece of power cable or grounding cable. 13. The grounding copper busbar is insulated from the wall, and the grounding path is as short as possible. 14. The primary power supply is connected to the power terminal on the shelf correctly. 15. The opening lug of power cables are welded or crimped firmly. 16. Power cables are well contacted with the copper lugs and sealed with adhesive tape. The copper lugs are reliably connected with the power cabinet or BTS shelf. 17. The power terminals on the top of the shelf are equipped with insulation tubes. 18. No power cable, grounding cable, trunk cable or RF cable is broken. 11-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 19. The labels at both ends of the power cable and ground cable should be clear and correct. 20. The naked wires at the wiring terminals and the handles of cable lugs are wrapped with insulation adhesive tape or heat-shrink tube. 21. Each wiring terminal is installed with a flat washer and a spring washer. 11.5 Checking T1 Cables Check if:
1. T1 cables are not short-circuited and the connectors are not damaged. 2. T1 cables are connected correctly and stuck with clear labels. 3. T1 cable connectors are firmly connected. Use the multimeter to test if the connectors are well connected with the grounding system. If the test result is negative, it might be caused by the poor contact between the flange of the connectors and the chassis. 4. T1 cables are laid loosely to ensure firm connection with the connectors of the shelf when the cabling rack moves up and down. 5. T1 cables are connected firmly and reliably. 11.6 Checking Indoor 1/2 Jumper Cables Check if:
1. The primary feeder cable is connected with the 1/2 jumper cable, which is then connected to the wiring terminal on the top of the shelf. 2. The indoor 1/2 jumper cables are stuck with labels indicating the corresponding sector and the length of the primary feeder cable. 3. The indoor jumper cables are cabled and bundled neatly. 4. The cabling is convenient for future maintenance and expansion. 5. The jumper cables are laid in different layers and sectors. 6. The jumper cable at the joint with the lightning arrester keeps straight for 30cm long. 11-4 Chapter 11 Hardware Installation Check 11.7 Checking Primary Feeder Cables and GPS Feeder Cables Check if:
1. The primary feeder cables are cut by a dedicated cutter. The cross-section is smooth and no copper scraps are left in the copper pipe of the primary feeder cable. The connectors of the primary feeder cables are installed firmly. 2. The 7/8 feeder cable connectors are installed firmly to ensure normal standing wave ratio. 3. The feeder cables are grounded at least three times as required (Refer to 6.2.3.1). The grounding points are connected firmly and sealed well. The end of the cable grounding kit for connecting the grounding cable is downward so that rainwater will not flow into the feeder cable along the grounding cable. 4. One feeder cable grounding kit is installed in the middle of the tower if the tower is more than 60m high. 5. One lightning grounding kit is installed on the top of a building or on the cabling rack if the length of the feeder cable after leaving the tower before entering the equipment room is more than 20m. 6. The terminals of the feeder cable grounding kit are fixed separately onto the tower. 7. The outdoor grounding copper busbar is connected with the underground grounding net by the dedicated cable whose cross-section area is more than 50mm2. 8. The antenna feeder system on the top of a building is connected to the nearby lightning grounding net. 9. The cabling ladder for leading the feeder cable from the building top along the wall to the equipment room is grounded. 10. The inclination between the feeder cable and its grounding cable is less than 15. 11. The feeder cables are laid neatly, neither cross-connected nor broken or twisted. The connections with the sectors are correct. 12. The minimum bending radius of feeder cables is 20 times of the semi-diameter of feeder cables or more. The bending radius of the primary feeder cables is larger than 0.3m. 11-5 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 13. The primary feeder cables of one sector are arranged in one row and they are queued the same in each row. 14. No copper part of the feeder cable connectors is exposed. Same labels are stuck at both ends of a feeder cable with the cable length recorded. 15. The GPS core wire is not falsely soldered. 16. The GPS copper core is not short-circuited with the outer layer, and the core pins of the GPS feeder cable connectors are not exposed. 17. The GPS feeder cable connectors are fastened tight. 11.8 Checking Water-blocking Curve for Feeder Cable Window and Primary Feeder Cables Check if:
1. The feeder cable window is fixed on the wall in the equipment room, and the protruding holes of the feeder cable window are outward faced. 2. The glue-injecting hole on sealing gasket of the feeder cable window is sealed upward. The window boards are installed in the indoor side of the window. 3. The feeder cable window installed on the top of a building is well sealed. 4. The lowest point of the water-blocking curve is at the place 10cm-20cm under the feeder cable window. 5. The minimum bending radius of feeder cables is 20 times of the semi-diameter of feeder cables or more. The bending radius of the primary feeder cables is more than 0.3m. 6. Keep a minimum length of 0.5m of straight feeder cable both in and out of the equipment room. There should be at least 0.3m of straight feeder cable in length through the lightning arrester. 11.9 Checking Hangers Check if:
1. The hangers are fastened firmly on the outdoor cabling rack. 2. The fixing clips installed are evenly distanced. 11-6 Chapter 11 Hardware Installation Check 3. The hangers are installed on the primary feeder cables every 1.5m.. 11.10 Checking Outdoor 1/2 Jumper Cables Check if:
1. The connections between the antenna and the 1/2 jumper cable as well as the 1/2 jumper cable and the primary feeder cable are correct. Their joints are tightened. 2. The jumper cable connected with the antenna is laid along the beam of the antenna mount and bound to the tower. 3. The joints between the antenna and the 1/2 jumper cable as well as the 1/2 jumper cable and the primary feeder are sealed as required (Refer to 9.4.6 and 9.6.6). 4. The jumper cable keeps straight with the antenna for 30cm long at their joint. 5. All the connectors of outdoor jumper cables are sealed and water-blocking curve is made for jumper cables. 11.11 Checking Antenna Check if:
1. The antenna mount is connected firmly with the tower. 2. The type of the antenna installed meets the requirement of the networking plan. 3. The height from the center of the antenna to the ground and the installation position of the antenna comply with the networking plan. 4. The RF antenna and the GPS antenna are installed in the area protected by the lightning rod. 5. The azimuth angle of each single-polarized directional antenna conforms to the networking plan. Two antennae of one sector are oriented to the same direction. The deviation of the azimuth angle of a directional antenna is within +/-5. 6. The pitch angle of each single-polarized antenna conforms to the networking plan. The deviation of the pitch angle of a directional antenna is within +/-0.5. The pitch angle of two single-polarized antennae is the same. 11-7 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 7. There are two types of antenna:
the pointer-modulated antenna and digital-modulated antenna. Adjust the former with a spanner and modulate the latter by setting the exact value in the equipment room. When the control line connecting the antenna is broken, you must adjust the antenna with a spanner. You must measure every single-polarized antenna. For digital-modulated antenna, keep the lower obliquity the same as planned, and keep consistency between the two single-polarized antennae. 8. All antenna poles are installed stably and grounded well. They are vertical to the ground, with the deviation within 2. 9. The transceiving distance of omni antennae is no less than 3.5m. 10. The distance between an omni antenna and the tower is more than 1.5m, and that between a directional antenna and the tower is more than 1m. 11. The top of the jacket of an omni antennae is level with or higher than the antenna mount. 12. The distance between an omni antenna and the antenna lightning rod is no less than 2.5m when the antenna situates on the rooftop. 13. An omni antenna can cover all areas when it is installed on the rooftop. 14. The diversity antenna of each sector corresponds with the jumper cables on top of the shelf. 15. The diversity distance between two antennae of one sector refers to the vertical distance between two antennae. The diversity distance is more than 3.5m for a 800M micro-BTS/remote station;
for a 1.9G micro-BTS/remote station is more than 1.5m; the diversity distance is more than 6.7m for a 450M micro-BTS/remote station. the diversity distance 16. The vertical distance between two directional antennae of different sectors installed on the same antenna mount is more than 0.6m. 17. The antennae are separated from G-network antennae, distancing more than 1m vertically and more than 2m horizontally. 18. The GPS antenna is installed in an open, low and safe place. It is vertical and its solid angle is bigger than 90. 19. A lightning rod is installed specially for the GPS antenna situated on rooftop. 11-8 Chapter 11 Hardware Installation Check 11.12 Checking Standing Wave Ratio of Feeder Cables 1. After the antennae are installed and all feeder cables are connected, measure the standing wave ratio of them. 2. Measure one end of the indoor 1/2 jumper cable, which is connected with the cabinet, with the tester. The standing wave ratio should be lower than 1.5. It is best to be lower than 1.3. 3. Record the VSWR value and provide the VSWR test diagram. 11.13 Checking Indoor and Outdoor Environment Check if:
1. All waste materials are cleared, and the outdoor environment is clean. 2. The equipment room is clean and neat, and all things needed are arranged in order. 3. No waste materials such as cable ties, cables and desiccant bags are left around/under the shelf and under the raised floor. 4. The front door, rear door and side panels are cleaned so that no touch prints can be seen. There is no dust or scrap in the cabinet. 11-9 12 Power-on and Power-off
Summary
Describing the power-on check items
Describing the procedures to power on/off a micro-BTS/remote station 12.1 Checking Components in the Cabinet before Power-on Open the cabinet to check if the modules are installed firmly and the cables are connected reliably. Insert the OIM and the CSM5000 into the cabinet. Set the PATH ID by setting the DIP switch on the BDM based on the T1 cable connections with the CDSU of the BSC. See Fig. 12.1-1 for the setting of the DIP switch. ON OFF 4 3 2 1 PATH_ID3 PATH_ID2 PATH_ID1 PATH_ID0 When PATH_ID=1, the DIP switch is set as:
When PATH_ID=5, the DIP switch is set as:
Fig. 12.1-1 Setting of S1 ON OFF ON OFF 12-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 12.2 Checking External Cables before Power-on 1. Use the multimeter to measure if the 120V AC power meets the requirement. 2. Check if the connector of the 120V AC power cable is connected firmly. 3. Check if T1 cable connectors are connected tight. 4. Check if the optical fibers are connected correctly. 5. Use the tester to check if the standing wave ratio of the antenna feeder system is lower than 1.5. It should be lower than 1.3 generally. Check if feeder cable connectors are assembled correctly, and if the feeder cables and antennae are in good condition. 6. Check if correct labels are stuck on the cables firmly. 12.3 Powering on/off the Cabinet No power switch is configured in micro-BTS or remote stations, so you need to power on/off them by plugging/unplugging the power connector or powering on/off the power supply equipment. After power-on, debug the BTS through the BSC. 12-2 13 Installing the Integrated Micro-BTS
Summary
Describing the installation of the integrated built-in SDH of the micro-BTS
Describing the installation of the integrated UPS of the micro-BTS 13.1 Introduction to the Solution of Micro-BTS Integration 13.1.1 Implementation of the Micro-BTS Integration The micro-BTS integration solution integrates the transmission, power and micro-BTS technologies and devices to provide users with an integrated networking solution. The core of the CDMA micro-BTS integration of ZTE Corporation lies in the built-in SDH. Through improvement on the structure and cabling process of the micro-BTS and change of related boards, the SDH board is built into the micro-BTS. In addition, the integrated UPS is added to the micro-BTS to provide the micro-BTS with the interfacing and monitoring functions over the backup power supply (UPS power supply and combinational power supply) and other devices. Meanwhile, the functions of secondary power-off and dry contact monitoring are added to address new requirements. The built-in SDH and integrated UPS are optional for micro-BTS configuration. The following modifications to the micro-BTS are required if this function is to be added to the micro-BTS:
1. BDM modification: Add the half-duplex RS485 monitoring interface and three dry contacts (input), no longer support the RS232 monitoring interface;
2. RFM modification: Add six dry contacts (input), not to support the RS485 and RS232 monitoring interface;
3. SDH selection: For the consistency of internal cabling, the CC4 connector is to be used for the T1 interface on the built-in SDH board, corresponding to the 13-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual indoor T150 board for the transmission of this part. The indoor and outdoor T150 boards are the same except for the interface connector, that is to say, they are basically the same in terms of performance and reliability. Support of power supply: 24V and 48V input;
4. Improvement on cabling process: Consistent internal T1 cabling, that is, the same cabling can be inserted either to the BDM or the to built-in SDH to make upgrade and networking configuration more more convenient and flexible;
internal cabling for the monitoring part;
5. Improvement on pinboard (bottom plate): Add a standalone built-in SDH power connector interface. The type of pinboard is settled on the 10W and 20W micro-BTS pinboard, 40W micro-BTS main cabient pinboard and 450M micro-BTS pinboard;
6. Add the lightning protection (class II) function for the monitoring part inside the cabinet with some lightning protection design on the board; furthermore, install an additional RS485/dry contact lightning protection board at the monitoring interface of the cabinet;
7. Modification of T1 lightning arrester: Because of the changed T1 cabling inside the cabinet, a longer coaxial cable may be needed for the T1 lightning arrester;
in addition, codes of the T1 lightning arrester needs changing;
8. Improve the door panel structure of the micro-BTS, to build the SDH into the door panel of the micro-BTS. 13.1.2 Micro-BTS Integration Solution Thanks to above improvements on the micro-BTS, the integration solution now poses as an even simpler one with more flexible configuration available. With the solution of the micro-BTS integrated with the backup power supply and transmission, the users requirements are taken as the first priority. There comes two basic integration solutions for selection:
1. AC micro-BTS+UPS+built-in SDH, as shown in Fig. 13.1-1. 13-2 Chapter 13 Installing the Integrated Micro-BTS Transmission interface Power supply interface Fiber 1 (SDH) Fiber 2 (SDH) E1(1) E1(2) E1(3) E1(4) AC micro-BTS Built-in SDH 220V
-48V 485/dry contact UPS Fig. 13.1-1 Solution (I) of Micro-BTS Integration In this solution, a ZTE ZXSM T150 transmission system serves as the built-in SDH system, and a ZTE ZXUPS L010 UPS power system serves as the UPS power supply.On the power interface, the UPS provides 120V and -48V power outputs to supply power for the micro-BTS and built-in SDH. Furthermore, the UPS provides secondary power-off function to guarantee the power supply of the built-in SDH in precedence.485 or dry contact are supported for the monitoring. There is only one monitoring interface at the micro-BTS side and this interface is compatible with the 485 and dry contact input, that is, it supports either the 485 or dry contact for the monitoring part. On the transmission interface side, two STM-1 optical interfaces are supported and a maximum of four T1 interfaces can be provided. In addition, the built-in SDH or BDM board can be selected according to the actual requirements. 2. DC micro-BTS+combinational power+built-in SDH, as shown in Fig. 13.1-2. 13-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Transmission interface Power supply interface Fiber 1 (SDH) Fiber 2 (SDH) E1(1) E1(2) E1(3) E1(4) DC micro-BTS Built-in SDH
-48V(1)
-48V(2) 485/dry contact Combinational power supply Fig. 13.1-2 Solution (II) of Micro-BTS Integration In this solution, a ZTE ZXSM T150 transmission system serves as the built-in SDH system, and a suitable ZTE power system model may serve as the outdoor combinational power supply. On the power interface side, the combinational power provides two -48V power outputs to supply power for the micro-BTS and the built-in SDH, Furthermore, the combinational power system provides the secondary power-off function to guarantee power supply for the built-in SDH in precedence. The monitor part and the transmission interface part are the same as those in Solution I. If the backup power is not available, the built-in SDH is also supported. However, the secondary power-off function cannot be implemented. To reduce power interfaces, the power of the built-in SDH can be supplied by the micro-BTS. In this case, a built-in 24V power and an SDH board are needed. Without the support of the backup power, if the electric power network is of poor quality, to reduce the influence of transmission interruption on the network due to power failure, it is recommended the configuration be used in a single station application only to avoid complicated SDH transmission networking. 13.1.3 Module Layout of the Integrated Micro-BTS and RF Remote Station Fig. 13.1-3 shows the module layout inside the ZXCBTS integrated micro-BTS:
13-4 Chapter 13 Installing the Integrated Micro-BTS 4 1 3 1 2 1 1 1 0 1 9 8 21 3 54 6 7 1 BDM module (top layer) 2 MTRX module (bottom layer) 3 power module 4 MDIV module 5 MLNA module 6. Heater 7 MPA module 8 T1 arrester 9 RF lightning arrester 10 MGPSTM lightning arrester 11 MTPB1 lightning-protection plate (the external 48VUPS should be built internally) 12 MDUP module 13 SDH board (if built-in SDH is necessary) 14 MGPSTM module 15 OIM board Fig. 13.1-3 Layout of Modules in the ZXCBTS micro-BTS 13-5 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Fig. 13.1-4 shows the module layout inside the ZXCBTS integrated RF remote station:
0 1 9 8 21 3 5 6 7 1 RFM module (top layer) 2 MTRX module (bottom layer) 3 power module 4 MDIV module 5 MLNA module 6 Heater 7 MPA module 8 RF arrester 9 MTPB1 lightning protection plate (the external 48VUPS should be built internally) 10 MDUP module Fig. 13.1-4 Layout of Internal Modules of the ZXCBTS RF Remote Station 13-6 13.1.4 Networking Modes of the Integrated SDH Chapter 13 Installing the Integrated Micro-BTS The built-in SDH technology is employed to make even more flexible networking of the micro-BTS and to address basically various networking requirements. The built-in SDH is a standard SDH STM-1 optical interface, which supports independent networking or networking with cooperation of an SDH device. The built-in SDH also supports directly fiber networking and has ring network protection capability. The built-in SDH cooperates with the SDH transmission equipment via standard T1 interfaces to flexibly support different networking modes such as point-to-point, chain, T-type, cross and ring modes and other hybrid networking modes. The built-in SDH micro-BTS supports independent networking or networking with cooperation of a standard SDH device. 13.2 Installing the Built-in SDH of Micro-BTS 13.2.1 Position and Internal Connection of the Built-in SDH in the Micro-BTS 13.2.1.1 Connections of the Built-in SDH Table 13.2-1 gives the cable connections of the built-in SDH in the CDMA micro-BTS. Table 13.2-1 Cable Connection of the Built-in SDH inside the CDMA Micro-BTS No. Cable Name Length (mm) To End A To End B 1 2 3 4 Power cables RF cable F-DC PWR-002 950 850 850 850 850 5000 Fiber cable As required on site
(at the SDH-POWER bottom of the cabinet) BDM_OUT1 BDM_IN1 BDM_OUT2 BDM_IN2 SDH-POWER bottom of the cabinet) FIBER-3 (at the bottom of the cabinet) FIBER-4 (at the bottom of the cabinet) the
(at SDH-X22 SDH-R1 SDH-T1 SDH-R2 SDH-T2 UPS supply power SDH-D43 SDH-D44 13.2.1.2 Schematic Diagram of Internal Cable Connection Fig. 13.2-1 gives the cable layout of the built-in SDH in the CDMA micro-BTS. 13-7 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Door panel GPS 10M ANT BDM 0 X R 1 X R OUT1IN1OUT2IN2OUT3IN3OUT4IN4 MTRX TX L N A L N A M P A D U P T4R4T3R3T2R1T1R1 X22 D43 D44 SDH B R F S M P D Bottom SDH-POWER IN2 OUT2 IN1 OUT1 Fig. 13.2-1 Cable Layout of the Built-in SDH in the CDMA Micro-BTS 13.2.2 Connecting the External Optical Fibers and Cables During Installation 13.2.2.1 Description of the Cabinet-Bottom Interfaces Fig. 13.2-2 shows all the cabinet-bottom interfaces of the micro-BTS:
POWER FIBER-1 FIBER-2 FIBER-3 FIBER-4 MONITOR FAN RFE-ANT0 RFE-ANT1 GPS-ANT SDH-POWER T1 EXTEND IN4 OUT4 IN3 OUT3 IN2 OUT2 IN1 OUT1 Fig. 13.2-2 Cabinet-bottom Interfaces of the CDMA Micro-BTS 13-8 Chapter 13 Installing the Integrated Micro-BTS See below for the meaning of each connector:
POWERPower input of the micro-BTS;
FIBER-1\-2Extension fiber interface of the RF remote station;
FIBER-3\-4Input/output of the built-in SDH fiber interface of the micro-BTS;
MONITORCommunication interface of the external UPS of the micro-BTS;
FANFan interface for external heat dissipation of the high-power (over 20W) micro-BTS;
RFE-ANT0Diversity reception antenna interface of the micro-BTS;
RFE-ANT1Main reception / transmission antenna interface of the micro-BTS;
GPS-ANTGPS antenna interface;
SDH-POWERBuilt-in SDH power supply interface of the micro-BTS;
T1Four 2M signal interfaces;
EXTENDRF extension interface of the multi-carrier micro-BTS. 13.2.2.2 Description of the Fiber Installation Here the interfaces related with the built-in SDH are FIBER-3 and FIBER-4. FIBER-3 is the optical transmission input interface and FIBER-4 is the fiber transmission output interface used for networking with the adjacent BTS. Fig. 13.2-3 shows the position for installing the water-proof fiber at the bottom of the micro-BTS cabinet and that for connecting and laying out the water-proof fiber inside the cabinet. The water-proof connector of the fiber is connected with the cabinet body in the similar way to the fiber connection when the micro-BTS connects with the RF remote station. The fiber is laid out in a naturally way after it goes into the cabinet and is connected with the optical module on the SDH. 13-9 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual SDH fiber SDH? ? ? ? ?
connector Fiber water-proof
connector Fig. 13.2-3 Connection of the Optical Fiber 13.3 Installing the Integrated UPS of Micro-BTS/RF Remote Station 13.3.1 Introduction to ZXUPS L010 Currently, the integrated CDMA micro-BTS employs the ZXUPS L010 as its UPS. Fig. 13.3-1 shows the appearance of the ZXUPS L010 series products. 13-10 Chapter 13 Installing the Integrated Micro-BTS Rear side of enclosure Shutter for air admittance Front side of enclosure Shutter for air discharge Key
CLOSE OPEN DANGER OF HIGH VOLTAGE Fig. 13.3-1 Appearance of the ZXUPS L010 Series Fig. 13.3-2 shows the inner structure of the ZXUPS L010 series. Door panel Rear-side installation hole Water outlet at the bottom Grounding hole at the bottom Installation hole at the bottom Bottom slide Leading-out hole at the bottom Fig. 13.3-2 Inner Structure of the ZXUPS L010 Series 13.3.2 Precautions for UPS Installation The following rules should be followed if the micro-BTS (800M or 1.9G) is to be configured with an additional UPS:
1. The UPS must be kept within two meters away from the micro-BTS. Because current micro-BTS uses the BDM for monitoring the UPS and the RS-232 specification for communication, the communication distance is limited to 10 meters generally. To ensure correct communication, no more than two meters should better be kept between two cabinets. As the UPS is relatively close to the micro-BTS, lightning-protection may be ignored for between them. 13-11 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 2. Improvement on the power connector of the micro-BTS. As the output of UPS is screwed with the bolt, the power supply of the current micro-BTS cannot be plugged. To improve this situation, a connector board may be used. Cut off the input 3-core connector on the connector board, divide by L-N-PE and connect respectively to the L-N-PE of the UPS output end. Be careful not to make any mistakes in this operation. In most cases, the brown line is for the live line (L), the blue line for neutral line (N) and the yellow-green line for protection grounding line (PE). 3. At present, the UPS employs the 232 communication mode and its RS232 interface differs from other standards. There are six pins in total Pin 6: RXD
(blue); Pin 7: GND (green); Pin 9: TXD (black), useful signal. The backup 232 interface of the BDM board is defined as: Pin 2: RXD; Pin 3: TXD; Pin 4:
GND. Therefore, the 232 connector of UPS has to be changed, that is: Connect RXD (blue) to Pin 3 of DB9, TXD (black) to Pin 2 of DB9, and GND (green) to Pin 4 of DB9. Remember that the DB9 connector must be a male one. 4. Precautions for installation 1) 2) 3) Good ventilation for heat dissipation;
Keep from the place with corrosive gas;
The top of UPS must not be occupied by any objects, nor could it be taken by a sitting person, lest the air vent might be blocked;. 13.3.3 Structural Feature and Installation Mode of UPS The ZXUPS L010UPS features a compact structure and boasts functions of dust-proof, water-proof, thermal insulation, anti-burglary, damp-proof, mildew-proof and corrosion protection. It is suitable for the outdoor environment in a remote area with formidable natural conditions. With the modular design, the enclosure is not only neat-looking but also rust-proof with excellent performance. This device can be installed easily and if it is for outdoor use, it can be set up on the flat ground along with other delivery-attached fittings, that is, the floor-type installation. Fig. 13.3-3 shows the floor-type installation of ZXUPS L010UPS. 13-12 Chapter 13 Installing the Integrated Micro-BTS d n u o r G
(4pcs) Spring cushion
(8pcs) Plain cushion M10x30 inner hexagon bolt 4 8 M10304
(4pcs) M8 nut M8 4 M84 M8 expansion screw
(4pcs)
(4pcs) Fig. 13.3-3 Frontal and Lateral Faces of the UPSs Floor-type Installation 13.3.4 Installing the Engineering Cables of L010UPS 13.3.4.1 From-to-list Table 13.3-1 shows the connections of the CDMA micro-BTS 485 / dry contact supplementary cables. Table 13.3-1 From-to-list of the CDMA Micro-BTS 485/dry contact supplementary cables No. Cable Name Length
(mm) 1 2 3 4 5 Monitoring cable Monitoring cable Monitoring cable Monitoring grounding cable Monitoring cable 800 800 470 170 3000 To End A To End B BDM-RS485 BDM-JOINT MTPB1-X3 MTPB1 MONITOR at the cabinet bottom at the MTPB1-X2 MTPB1-X1 MONITOR cabinet bottom Grounding hole at the right side of the cabinet DB9 socket of UPS 13.3.4.2 Layout of Cabling Fig. 13.3-4 shows the layout of the monitoring cables of the CDMA micro-BTS 485/dry contact:
13-13 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Connected together with the front-door grounding cable Bottom MONOTOR MTPB1 lightning-
protection board Fig. 13.3-4 Layout of the Monitoring Cables of the CDMA Micro-BTS 485/Dry Contact Here three interfaces, namely POWER, MONITOR and SDH-POWER are related to the external UPS. Where, One cable end of POWER interface is connected with the POWER interface, and the other end is a standard 3-core power plug. To connect with the UPS, the 3-pin plug should be cut off first, then the three core wires (yellow-green, blue and brown, corresponding respectively to the ground line, neutral line and live line) should be connected with the output terminal of UPS properly;
For the cable connection of the MONITOR interface, refer to the above-mentioned from-to-list. One end of the cable for the SDH-POWER interface is connected with this interface, and the other with the secondary power-off output connecting terminal of UPS, with the red and blue core wires connecting with the -48V, and the black and yellow-green ones with the ground. 13.3.5 Installing UPS As a product of ZTE, the ZXUPSL010 is delivered with the proper users manual 13-14 Chapter 13 Installing the Integrated Micro-BTS attached, and this manual gives detailed instructions on the installation of the product. 13.4 Installing Micro-BTS/RF Remote Station the Ancillary Combinational Power Supply of The following ancillary power supply is recommended for the devices of the CDMA cellular system: the ancillary combinational power supply consists of the outdoor power box and outdoor battery box (model: ZXDU28). The outdoor power box may be installed with a pole, on the wall or on the ground; while the outdoor battery box may only be installed on the ground. Given below is the brief introduction of the installation method and connection of the outdoor power box and outdoor battery box. 13.4.1 Installing the Outdoor Power Box 13.4.1.1 Installing the Outdoor Power Box with a Pole Fig. 13.4-1 shows how the outdoor power box is installed on the pole. 1Outdoor power box 2Sunshade unit 1 (used for installation with a pole or on the wall) 3Mechanical part of pole (used for installation with a pole) 4Installation support (used for installation with a pole or on the wall) Fig. 13.4-1 Schematic Diagram of Installing the Outdoor Power Box with a Pole 13-15 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 13.4.1.2 Installing the Outdoor Power Box on the Wall Fig. 13.4-2 shows how to install the outdoor power box on the wall. 1Outdoor power box 2Sunshade unit 1 (used for installation with a pole or on the wall) 3Installation support (used for installation with a pole or on the wall) 4Expansion bolt M10X50 Fig. 13.4-2 Schematic Diagram of Installing the Outdoor Power Box on the Wall 13.4.1.3 Installing the Outdoor Power Box on the Ground Fig. 13.4-3 shows how to install the outdoor power box on the ground. 1Outdoor power box 2Sunshade unit 2 (used for installation on the ground) 13-16 Chapter 13 Installing the Integrated Micro-BTS 3Base (used for installation on the ground) 4Expansion bolt M10X50 Fig. 13.4-3 Schematic Diagram of Installing the Outdoor Power Box on the Ground 13.4.2 Installing the Outdoor Battery Box The outdoor can only be installed on the ground, which is shown in Fig. 13.4-4. 1Outdoor battery box 2Sunshade unit 2 (used for the installation on the ground) 3Base (used for installation on the ground) 4Expansion bolt M10X50 Fig. 13.4-4 Schematic Diagram of Installing the Outdoor Battery Box on the Ground 13.4.3 Cable Connection for Outdoor Power Box The cable connection for the outdoor power box is presented in Fig. 13.4-5. 13-17 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 1. Dry contact output connecting terminal 2. Load output working ground 3. Battery input working ground 4. 48V load output line 5. (-48V) battery input line 6. Cable holder 7. External AC input line 8. Systems cable access hole Fig. 13.4-5 Schematic Diagram of the Cable Connection for the Outdoor Power Box The function of dry contact monitoring is available with the combinational power supply of the micro-BTS. The actual definition of the dry contacts output connecting terminal is (from top down): 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10, as shown in Fig. 13.4-6. 13-18 Chapter 13 Installing the Integrated Micro-BTS 1 2 3 4 5 6 7 8 9 10 Fig. 13.4-6 Output Connecting Terminal of the Dry Contact Precautions for the cable connection of the combinational power supply:
1. Description of dry contact pairs: As shown in the above figure, 1 and 2 are a pair of dry contacts (for the mains status alarm); 3 and 4 are a pair of dry contacts (for the battery under-voltage alarm); 5 and 6 are a pair of dry contacts
(for the rectifier fault alarm); 7 and 8 are a pair of dry contacts (for the access control alarm). The micro-BTS monitors only the first three, that is, the access control monitoring is excluded. Between the dry contacts of the micro-BTS and the combinational power supply, a 7-core monitoring cable attached with delivery is used for the connection. 2. The cross-section area of the systems AC input cable should be no smaller than 6mm2. 3. The cross-section area of the batterys input cable should be no smaller than 16mm2. 4. The cross-section area of the DC load output cable should be no smaller than 10mm2. 5. There are clear silk-screen prints for the connecting terminals and the switch definitions under the corresponding devices. Please check them out before you go on with the connection or operation. As the outdoor power box and outdoor battery box of the ancillary combinational 13-19 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual power supply are products of ZTE, proper users manual will be attached with the product delivery. Detailed instructions are covered in these manuals for users reference during the installation. 13-20 Appendix A Packaging, Storage and Transportation
Summary
Describing how a micro-BTS/remote station is packed.
Describing how a micro-BTS/remote station should be stored.
Describing how a micro-BTS/remote station should be transported. A.1 Packaging The packaging of all components of micro-BTS, ultra-wide micro-BTS, and remote station are properly proofed against quakes during transportation. They are divided into two groups in packaging:
1. Cabinets 2. Cables and delivery-attached document Each item has been identified with model, name, placement direction, number of layers, together with signs of No damping, and Fragile etc. A.2 Storage Keep all components in the original package. Keep the storeroom in order, and mark the number of equipment sets in stock. The range of temperature is -40C ~+75C, and the range of relative humidity is 5%~100%. Adopt measures of anti-moisture, anti-dust, quake-proof, and anti-erosion. It is recommended to equip air-conditioner and lighting equipment. The stock duration should be less than six months. A-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual A.3 Transportation Use designated containers. All items should be placed closely, neatly, orderly and safely in the container to avoid any possible damage during transportation. There should be three layers of wooden box or four layers of cartons at maximum. Cables and delivery-attached document should be placed in the lower half and the cabinet should be placed in the upper half. Never put the equipment in open freight cars or ships. Never leave the equipment in open warehouses. Never transport the equipment with flammable, explosive or erosive chemicals. Keep the equipment away from being washed by rains and snow, or any physical damage. Keep the equipment away from electromagnetic or radiant substance during transportation. Ensure that all items are in the correct placement direction before being lifted during transportation. A-2 Appendix B Table of Cable Connections
Summary
Refer to the following tables for the cable connections in micro-BTS and remote stations. B.1 Cable Connections in M800T Single-carrier Micro-BTS Table B.1-1 Cable Connections in M800T Single-carrier Micro-BTS Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX04 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA800 MLNA800-1,-2 MPA800 Door grounding point Cabinet Cabinet Cabinet BDM800_X39 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) B-1 MPD_X11 MPA800 MLNA800 BRFS_X6 MONDX02_B MONDX01_B MTRX800 Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power brown) Grounding point (black) Power lightning arrester External AC power lightning arrester Power lightning arrester
(blue, The configuration in case that AC power is supplied The configuration in case that DC power Serial No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Cable Name Connection of Terminal A Connection of Terminal B Remarks External -48V power is supplied Serial No. 18 19 20 21 22 23 24 25 26 27 28 29 30 31 F-DC PWR-002 F-DC PWR-003 RF21 RF22 RF23 RF24 RF25 RF26 RF27 RF28 RF29 RF30 RF31 GPS-BDM F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MDIV800_RX MLNA800-2_IN MTRX800_RX0 MTRX800_RX1 MTRX800_TX MDIV800_ANT Power lightning arrester MLNA800-1_IN MDUP800_RX MLNA800-1_RFOUT1 MLNA800-2_RFOUT1 MPA800_IN RFE-ANT0 (at the bottom of the cabinet) RFE-ANT1 (at the bottom of the cabinet) MPA800_OUT GPS-ANT at the bottom of the cabinet MGPS_10M BDM800_X8 BDM800_X3 MDUP800_ANT MDUP800_TX MGPS_ANT BDM800_X7 Middle hole of BRFS_X1 BGPS_X2 B.2 Cable Connections in M800T Double-carrier Micro-BTS Table B.2-1 Cable Connections in M800T Double-carrier Micro-BTS Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX04 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA800 MLNA800-2 MPA800 Door grounding point Cabinet Cabinet Cabinet BDM800_X39 MPD_X11 MPA800 MLNA800 BRFS_X6 MONDX02_B MONDX01_B MTRX800 Cabinet grounding point Lightning arrester BDM Door Door status switch B-2 Serial No. 1 2 3 4 5 6 7 8 9 10 11 Serial No. Appendix B Table of Cable Connections Cable Name Connection of Terminal A Connection of Terminal B Remarks
(blue, The configuration in case that AC power is supplied The configuration in case that DC power is supplied 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF22 RF24 RF25 RF27 RF28 RF29 RF30 RF31 RF42 RF43 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
(Black) MPD_V+
MTRX800_RX1 MTRX800_TX RFE-ANT1 (at the bottom of the cabinet) MPA800_OUT GPS-ANT (at the bottom of the cabinet) MGPS_10M BDM800_X8 MLNA800-2_RFOUT2 MTRX800_RX0 GPS-BDM BDM800_X3 lightning arrester Power lightning arrester Heater Power brown) Grounding point (black) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester MDUP800_RX MLNA800-2_RFOUT1 MPA800_IN MDUP800_ANT MDUP800_TX MGPS_ANT BDM800_X7 Middle hole of BRFS_X1 RFE-ANT0 (at the bottom of the cabinet) EXTEND (at the bottom of the cabinet) BGPS_X2 Note: Please refer to precautions listed in Table B-1. B.3 Cable Connections in R800T Single-carrier Remote Stations Table B.3-1 Cable Connections in R800T Single-carrier Remote Stations Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 BRFS_X5 MPD_X6 MPD_X7 MPD_X11 MPA800 MLNA800 B-3 Serial No. 1 2 3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Serial No. Cable Name Connection of Terminal A Connection of Terminal B Remarks RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF21 RF22 RF23 RF24 RF25 RF26 RF27 RF28 RF40 RF41 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 BRFS_X6 MONDX02_B MONDX01_B MTRX800 Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power brown) Grounding point (black) Power lightning arrester External AC power lightning arrester Power lightning arrester External -48V power Power lightning arrester
(blue, The configuration in case that AC power is supplied The configuration in case that DC power is supplied MPD_X5 MPA800 MLNA800-1, -2 MPA800 Door grounding point Cabinet Cabinet Cabinet RFM_X24 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MDIV800_RX MLNA800-2_IN MTRX800_RX0 MTRX800_RX1 MTRX800_TX MDIV800_ANT MLNA800-1_IN MDUP800_RX MLNA800-1_RFOUT1 MLNA800-2_RFOUT1 MPA800_IN RFE-ANT0 (at the bottom of the cabinet) RFE-ANT1 (at the bottom of the cabinet) MPA800_OUT Middle hole of BRFS_X1 RFM_X7 MDUP800_ANT MDUP800_TX Middle hole of BRFS_X3 Middle hole of RFM_X3 B-4 Appendix B Table of Cable Connections B.4 Cable Connections in R800T Double-carrier Remote Stations Table B.4-1 Cable Connections in R800T Double-carrier Remote Stations Serial No. Cable Name Connection of Terminal A Connection of Terminal B Remarks 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF22 RF24 RF25 RF27 RF28 RF40 RF41 RF42 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA800 MLNA800-2 MPA800 Door grounding point Cabinet Cabinet Cabinet RFM_X24 MPD_X4 MPD_HP POWER (at the bottom of the cabinet)
(blue, MPD_X11 MPA800 MLNA800 BRFS_X6 MONDX02_B MONDX01_B MTRX800 Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power brown) Grounding point (black) Power lightning arrester External AC power lightning arrester External -48V power Power lightning arrester Power lightning arrester MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MLNA800-2_IN MTRX800_RX1 MTRX800_TX RFE-ANT1 (at the bottom of the cabinet) MPA800_OUT Middle hole of BRFS_X1 Middle hole of BRFS_X3 Middle hole of RFM_X3 RFM_X7 RFE-ANT0 (at the bottom of the cabinet) MDUP800_RX MLNA800-2_RFOUT1 MPA800_IN MLNA800-2_RFOUT2 MDUP800_ANT MDUP800_TX The configuration in case that AC power is supplied The configuration in case that DC power is supplied B-5 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Serial No. Cable Name Connection of Terminal A Connection of Terminal B Remarks 28 RF43 MTRX800_RX0 EXTEND (at the bottom of the cabinet) B.5 Cable Connections in M190T Single-carrier Micro-BTS Table B.5-1 Cable Connections in M190T Single-carrier Micro-BTS Serial No. Cable Name Connection of Terminal A Connection of Terminal B Remarks 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF21 RF22 RF23 RF24 RF25 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA800 MLNA800-1, -2 MPA800 Door grounding point Cabinet Cabinet Cabinet RFM_X24 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MDIV800_RX MLNA800-2_IN MTRX800_RX0 MTRX800_RX1 MTRX800_TX MPD_X11 MPA800 MLNA800 BRFS_X6 MONDX02_B MONDX01_B MTRX800 Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester MLNA800-1_IN MDUP800_RX MLNA800-1_RFOUT1 MLNA800-2_RFOUT1 MPA800_IN B-6 The configuration in case that AC power is supplied The configuration in case that DC power is supplied Serial No. Appendix B Table of Cable Connections Cable Name Connection of Terminal A Connection of Terminal B Remarks 25 26 27 28 29 RF26 RF27 RF28 RF40 R41 MDIV800_ANT RFE-ANT0 (at the bottom of the cabinet) MDUP800_ANT RFE-ANT1 (at the bottom of the cabinet) MPA800_OUT Middle hole of BRFS_X1 Middle hole of BRFS_X3 Middle hole of RFM_X3 RFM_X7 MDUP800_TX B.6 Cable Connections in M190T Double-carrier Micro-BTS Table B.6-1 Cable Connections in M190T Double-carrier Micro-BTS Serial No. Cable Name Connection of Terminal A Connection of Terminal B Remarks 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA800 MLNA800-2 MPA800 Door grounding point Cabinet Cabinet Cabinet RFM_X24 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MPD_X11 MPA800 MLNA800 BRFS_X6 MONDX02_B MONDX01_B MTRX800 Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester B-7 The configuration in case that AC power is supplied The configuration in case that DC power is supplied ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Serial No. 20 21 22 23 24 25 26 27 28 Cable Name Connection of Terminal A Connection of Terminal B Remarks RF22 RF24 RF25 RF27 RF28 RF40 RF41 RF42 RF43 MLNA800-2_IN MTRX800_RX1 MTRX800_TX RFE-ANT1 (at the bottom of the cabinet) MPA800_OUT Middle hole of BRFS_X1 RFM_X7 MLNA800-2_RFOUT2 MTRX800_RX0 MDUP800_RX MLNA800-2_RFOUT1 MPA800_IN MDUP800_ANT MDUP800_TX Middle hole of BRFS_X3 Middle hole of RFM_X3 RFE-ANT0 (at cabinet) EXTEND (at the bottom of the cabinet) the bottom of the B.7 Cable Connections in R190T Single-carrier Remote Stations Table B.7-1 Cable Connections in R190T Single-carrier Remote Stations Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 ACDX03 ACDX01 ACDX02 ACDX04 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA800 MLNA800-2 MPA800 Door grounding point Cabinet Cabinet Cabinet RFM_X24 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A MPD_X11 MPA800 MLNA800 BRFS_X6 MONDX02_B MONDX01_B MTRX800 Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power B-8 The configuration in case that AC power is supplied Serial No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Serial No. Appendix B Table of Cable Connections Cable Name Connection of Terminal A Connection of Terminal B Remarks 17 18 19 20 21 22 23 24 25 26 27 28 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF22 RF24 RF25 RF27 RF28 RF40 RF41 RF42 RF43 External -48V power Power lightning arrester Power lightning arrester MDUP800_RX MLNA800-2_RFOUT1 MPA800_IN POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MLNA800-2_IN MTRX800_RX1 MTRX800_TX RFE-ANT1 (at the bottom of the cabinet) MPA800_OUT Middle hole of BRFS_X1 Middle hole of BRFS_X3 RFM_X7 Middle hole of RFM_X3 RFE-ANT0 cabinet) EXTEND (at the bottom of the cabinet) MLNA800-2_RFOUT2 MDUP800_ANT MTRX800_RX0 the bottom of MDUP800_TX
(at the The configuration in case that DC power is supplied B.8 Cable Connections in R190T Double-carrier Remote Stations Table B.8-1 Cable Connections in R190T Double-carrier Remote Stations Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 ACDX03 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA1900 MLNA1900-2 MPA1900 Door grounding point Cabinet Cabinet Cabinet RFM_X24 MPD_X4 MPD_HP MPD_X11 MPA1900 MLNA1900 BRFS_X6 MONDX02_B MONDX01_B MTRX1900 Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater B-9 Serial No. 1 2 3 4 5 6 7 8 9 10 11 12 13 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Serial No. 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Cable Name Connection of Terminal A Connection of Terminal B Remarks External -48V power Power lightning arrester Power lightning arrester Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MTRX1900_TX MLNA1900-2_IN MPA1900_OUT MTRX1900_RX1 RFE-ANT1 (at the bottom of the cabinet) Middle hole of BRFS_X1 Middle hole of BRFS_X3 Middle hole of RFM_X3 RFM_X7 RFE-ANT0 cabinet) EXTEND (at the bottom of the cabinet) MPA1900_IN MDUP1900_RX MDUP1900_TX MLNA1900-2_RFOUT1 MLNA1900-2_RFOUT2 MDUP1900_ANT MTRX1900_RX0 the bottom of
(at the The configuration in case that AC power is supplied The configuration in case that DC power is supplied ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF25 RF33 RF34 RF36 RF38 RF40 RF41 RF42 RF43 B.9 Cable Connections in M802T Single-carrier Micro-BTS Table B.9-1 Cable Connections in M802T Single-carrier Micro-BTS Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA MLNA800-1, -2 MPA Door grounding point Cabinet Cabinet MPD_X11 MPA MLNA800 BRFS_X6 MONDX02_B MONDX01_B MTRX800 Cabinet grounding point Lightning arrester BDM B-10 Serial No. 1 2 3 4 5 6 7 8 9 Serial No. Appendix B Table of Cable Connections Cable Name Connection of Terminal A Connection of Terminal B Remarks 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 DX03 DX04 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 F-FAN-004 F-FAN-005 F-FAN-006 RF21 RF22 RF23 RF24 R25 RF26 RF27 RF28 RF29 RF30 RF31 GPS-BDM Cabinet BDM802_X39 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MPD COMMAN (at the bottom of the cabinet) COMMAN (at the bottom of the cabinet) MDIV800_RX MLNA800-2_IN MTRX800_RX0 MTRX800_RX1 MTRX800_TX MDIV800_ANT RFE-ANT1 (at the bottom of the cabinet) MPA_OUT GPS-ANT at the bottom of the cabinet MGPS_10M BDM802_X8 BDM802_X3 The configuration in case that AC power is supplied The configuration in case that DC power is supplied Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester Internal fan rack MPD External fan rack MLNA800-1_IN MDUP800_RX MLNA800-1_RFOUT1 MLNA800-2_RFOUT1 MPA_IN RFE-ANT0 cabinet)
(at the bottom of MDUP800_ANT MDUP800_TX MGPS_ANT BDM802_X7 Middle hole of BRFS_X1 BGPS_X2 the B-11 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual B.10 Cable Connections in M802T Double-carrier Micro-BTS Table B.10-1 Cable Connections in M802T Double-carrier Micro-BTS Serial No. Cable Name Connection of Terminal A Connection of Terminal B Remarks 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX04 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 F-FAN-004 F-FAN-005 F-FAN-006 RF22 RF24 RF25 RF27 RF28 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA MLNA800-2 MPA Door grounding point Cabinet Cabinet Cabinet BDM802_X39 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MPD COMMAN (at the bottom of the cabinet) COMMAN (at the bottom of the cabinet)
(Black) MPD_V+
MTRX800_RX1 MTRX800_TX RFE-ANT1 (at the bottom of the cabinet) MPA_OUT MPD_X11 MPA MLNA800 BRFS_X6 MONDX02_B MONDX01_B MTRX800 Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester Internal fan rack MPD External fan MDUP800_RX MLNA800-2_RFOUT1 MPA_IN MDUP800_ANT MDUP800_TX B-12 The configuration in case that AC power is supplied The configuration in case that DC power is supplied Serial No. Appendix B Table of Cable Connections Cable Name Connection of Terminal A Connection of Terminal B Remarks 28 29 30 31 32 33 RF29 RF30 RF31 RF42 GPS-ANT at the bottom of the cabinet MGPS_10M BDM802_X8 MLNA800-2_RFOUT2 RF43 GPS-BDM MTRX800_RX0 BDM802_X3 MGPS_ANT BDM802_X7 Middle hole of BRFS_X1 RFE-ANT0 cabinet) EXTEND (at the bottom of the cabinet) BGPS_X2 the bottom of
(at the B.11 Cable Connections in R802 Single-carrier RF Remote Stations Table B.11-1 Cable Connections in R802T Single-carrier Remote Stations Serial No. Cable Name Connection of Terminal A Connection of Terminal B Remarks 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA MLNA800-1, -2 MPA Door grounding point Cabinet Cabinet RFM_X24 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MPD_X11 MPA MLNA800 BRFS_X6 MONDX02_B MONDX01_B MTRX800 Cabinet grounding point Lightning arrester Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester B-13 The configuration in case that AC power is supplied The configuration in case that DC power is supplied ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Serial No. 20 21 22 23 24 25 26 27 28 29 30 31 Cable Name Connection of Terminal A Connection of Terminal B Remarks MDIV800_RX MLNA800-2_IN MTRX800_RX0 MTRX800_RX1 MTRX800_TX MDIV800_ANT RFE-ANT1 (at the bottom of the cabinet) MPA_OUT Middle hole of BRFS_X1 RFM_X7 COMMAN (at the bottom of the cabinet) COMMAN (at the bottom of the cabinet) MLNA800-1_IN MDUP800_RX MLNA800-1_RFOUT1 MLNA800-2_RFOUT1 MPA_IN RFE-ANT0 (at the bottom of the cabinet) MDUP800_ANT MDUP800_TX Middle hole of BRFS_X3 Middle hole of RFM_X3 MPD External fan RF21 RF22 RF23 RF24 RF25 RF26 RF27 RF28 RF40 RF41 F-FAN-005 F-FAN-006 B.12 Cable Connections in R802T Double-carrier Remote Stations Table B.12-1 Cable Connections in R802T Double-carrier RF Remote Stations Serial No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 ACDX03 ACDX01 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA MLNA800-2 MPA Door grounding point Cabinet Cabinet RFM_X24 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X11 MPA MLNA800 BRFS_X6 MONDX02_B MONDX01_B MTRX800 Cabinet grounding point Lightning arrester Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) The configuration in case that AC power B-14 Serial No. Appendix B Table of Cable Connections Cable Name Connection of Terminal A Connection of Terminal B Remarks 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF22 RF24 RF25 RF27 RF28 RF40 RF41 RF42 RF43 F-FAN-005 F-FAN-006 MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MLNA800-2_IN MTRX800_RX1 MTRX800_TX RFE-ANT1 (at the bottom of the cabinet) MPA_OUT Middle hole of BRFS_X1 RFM_X7 MLNA800-2_RFOUT2 MTRX800_RX0 COMMAN (at the bottom of the cabinet) COMMAN (at the bottom of the cabinet) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester MDUP800_RX MLNA800-2_RFOUT1 MPA_IN MDUP800_ANT MDUP800_TX Middle hole of BRFS_X3 Middle hole of RFM_X3 RFE-ANT0 cabinet) EXTEND (at the bottom of the cabinet) the bottom of
(at the MPD External fan is supplied The configuration in case that DC power is supplied B.13 Cable Connections in M191T Single-carrier Micro-BTS Table B.13-1 Cable Connections in M191T Single-carrier Micro-BTS Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA LNA-1, -2 MPA Door grounding point MPD_X11 MPA LNA BRFS_X6 MONDX02_B MONDX01_B TRX Cabinet grounding point B-15 Serial No. 1 2 3 4 5 6 7 8 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Serial No. Cable Name Connection of Terminal A Connection of Terminal B Remarks 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 DX02 DX03 DX04 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF25 RF29 RF32 RF33 RF34 RF35 RF36 RF37 RF38 RF39 GPS-BDM Cabinet Cabinet Cabinet BDM_X39 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
TRX_TX GPS-ANT at the bottom of the cabinet DIV_RX LNA-2_IN MPA_OUT TRX_RX0 TRX_RX1 DIV_ANT RFE-ANT1 (at the bottom of the cabinet) MGPS_10M BDM_X3 Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester The configuration in case that AC power is supplied The configuration in case that DC power is supplied MPA_IN MGPS_ANT LNA-1_IN DUP_RX DUP_TX LNA-1_RFOUT1 LNA-2_RFOUT1 RFE-ANT0 (at cabinet) DUP_ANT the bottom of the Middle hole of BRFS_X1 BGPS_X2 B.14 Cable Connections in M191T Double-carrier Micro-BTS Table B.14-1 Cable Connections in M191T Double-carrier Micro-BTS Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 BRFS_X5 MPD_X11 B-16 Serial No. 1 Serial No. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Appendix B Table of Cable Connections Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX04 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF25 RF29 RF33 RF34 RF36 RF38 RF39 RF42 MPD_X6 MPD_X7 MPD_X5 MPA LNA-2 MPA Door grounding point Cabinet Cabinet Cabinet BDM_X39 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
TRX_TX GPS-ANT at the bottom of the cabinet LNA-2_IN MPA_OUT TRX_RX1 RFE-ANT1 (at the bottom of the cabinet) MGPS_10M LNA-2_RFOUT2 RF43 GPS-BDM TRX_RX0 BDM_X3 MPA LNA BRFS_X6 MONDX02_B MONDX01_B TRX Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester MPA_IN MGPS_ANT DUP_RX DUP_TX LNA-2_RFOUT1 DUP_ANT the bottom of Middle hole of BRFS_X1 RFE-ANT0 (at cabinet) EXTEND (at the bottom of the cabinet) BGPS_X2 the The configuration in case that AC power is supplied The configuration in case that DC power is supplied B-17 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual B.15 Cable Connections in R191T Single-carrier Remote Stations Table B.15-1 Cable Connections in R191T Single-carrier Remote Stations Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF25 RF32 RF33 RF34 RF35 RF36 RF37 RF38 RF40 RF41 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA LNA-1, -2 MPA Door grounding point Cabinet Cabinet Cabinet RFM_X24 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
TRX_TX DIV_RX LNA-2_IN MPA_OUT TRX_RX0 TRX_RX1 DIV_ANT MPD_X11 MPA LNA BRFS_X6 MONDX02_B MONDX01_B TRX Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester MPA_IN LNA-1_IN MDUP1900_RX MDUP1900_TX LNA-1_RFOUT1 LNA-2_RFOUT1 RFE-ANT0
(at cabinet) the bottom of the RFE-ANT1 (at the bottom of the cabinet) Middle hole of BRFS_X1 RFM_X7 MDUP1900_ANT Middle hole of BRFS_X3 Middle hole of RFM_X3 B-18 The configuration in case that AC power is supplied The configuration in case that DC power is supplied Serial No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Appendix B Table of Cable Connections B.16 Cable Connections in R191T Double-carrier Remote Stations Table B.16-1 Cable Connections in R191T Double-carrier Remote Stations Serial No. Cable Name Connection of Terminal A Connection of Terminal B Remarks 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF25 RF33 RF34 RF36 RF38 RF40 RF41 RF42 RF43 MPD_X11 MPA LNA BRFS_X6 MONDX02_B MONDX01_B TRX Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA LNA-2 MPA Door grounding point Cabinet Cabinet Cabinet RFM_X24 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
TRX_TX LNA-2_IN MPA_OUT TRX_RX1 RFE-ANT1 (at the bottom of the cabinet) Middle hole of BRFS_X1 Middle hole of BRFS_X3 RFM_X7 Middle hole of RFM_X3 RFE-ANT0 cabinet) EXTEND (at the bottom of the cabinet) MPA_IN MDUP1900_RX MDUP1900_TX LNA-2_RFOUT1 Power lightning arrester Power lightning arrester External -48V power MDUP1900_ANT LNA-2_RFOUT2 the bottom of TRX_RX0
(at the The configuration in case that AC power is supplied The configuration in case that DC power is supplied B-19 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual B.17 Cable Connections in M192T Single-carrier Micro-BTS Table B.17-1 Cable Connections in M192T Single-carrier Micro-BTS Serial No. Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX04 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 F-FAN-004 F-FAN-005 F-FAN-006 RF25 RF29 RF32 RF33 RF34 RF35 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA MLNA-1, -2 MPA Door grounding point Cabinet Cabinet Cabinet BDM_X39 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MPD COMMAN (at the bottom of the cabinet) COMMAN (at the bottom of the cabinet) TRX_TX GPS-ANT at the bottom of the cabinet DIV_RX LNA-2_IN MPA_OUT TRX_RX0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 MPD_X11 MPA MLNA BRFS_X6 MONDX02_B MONDX01_B TRX Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester Internal fan rack MPD External fan rack MPA_IN MGPS_ANT LNA-1_IN DUP_RX DUP_TX LNA-1_RFOUT1 B-20 The configuration in case that AC power is supplied The configuration in case that DC power is supplied Appendix B Table of Cable Connections Serial No. 29 30 31 32 33 Cable Name Connection of Terminal A Connection of Terminal B Remarks RF36 RF37 RF38 RF39 GPS-BDM TRX_RX1 DIV_ANT RFE-ANT1 (at the bottom of the cabinet) MGPS_10M BDM_X3 LNA-2_RFOUT1 RFE-ANT0
(at cabinet) DUP_ANT the bottom of the Middle hole of BRFS_X1 BGPS_X2 B.18 Cable Connections in M192T Double-carrier Micro-BTS Table B.18-1 Cable Connections in M192T Double-carrier Micro-BTS Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX04 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA MLNA-2 MPA Door grounding point Cabinet Cabinet Cabinet BDM_X39 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
MPD_X11 MPA MLNA BRFS_X6 MONDX02_B MONDX01_B TRX Cabinet grounding point Lightning arrester BDM Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power Power lightning arrester External -48V power Power lightning arrester B-21 The configuration in case that AC power is supplied The configuration in case that DC power is supplied Serial No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Serial No. 20 21 22 23 24 25 26 27 28 29 30 31 32 Cable Name Connection of Terminal A Connection of Terminal B Remarks F-FAN-004 F-FAN-005 F-FAN-006 RF25 RF29 RF33 RF34 RF36 RF38 RF39 RF42 MPD COMMAN (at the bottom of the cabinet) COMMAN (at the bottom of the cabinet) TRX_TX GPS-ANT at the bottom of the cabinet LNA-2_IN MPA_OUT TRX_RX1 RFE-ANT1 (at the bottom of the cabinet) MGPS_10M LNA-2_RFOUT2 RF43 GPS-BDM TRX_RX0 BDM_X3 Internal fan rack MPD External fan MPA_IN MGPS_ANT DUP_RX DUP_TX LNA-2_RFOUT1 DUP_ANT
(at the bottom of Middle hole of BRFS_X1 RFE-ANT0 cabinet) EXTEND (at the bottom of the cabinet) BGPS_X2 the B.19 Cable Connections in R192T Single-carrier Remote Stations Table B.19-1 Cable Connections in R192T Single-carrier Remote Stations Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPA LNA-1, -2 MPA Door grounding point Cabinet Cabinet RFM_X24 MPD_X4 MPD_X11 MPA LNA BRFS_X6 MONDX02_B MONDX01_B TRX Cabinet grounding point Lightning arrester Door Door status switch Power lightning arrester B-22 Serial No. 1 2 3 4 5 6 7 8 9 10 11 12 Serial No. Appendix B Table of Cable Connections Cable Name Connection of Terminal A Connection of Terminal B Remarks 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF25 RF32 RF33 RF34 RF35 RF36 RF37 RF38 RF40 RF41 F-FAN-005 F-FAN-006 MPD_HP POWER (at the bottom of the cabinet) MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
TRX_TX DIV_RX LNA-2_IN MPA_OUT TRX_RX0 TRX_RX1 DIV_ANT Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power The configuration in case that AC power is supplied Power lightning arrester External -48V power Power lightning arrester The configuration in case that DC power is supplied MPA_IN LNA-1_IN MDUP1900_RX MDUP1900_TX LNA-1_RFOUT1 LNA-2_RFOUT1 RFE-ANT0 (at cabinet) the bottom of the MDUP1900_ANT RFE-ANT1 (at the bottom of the cabinet) Middle hole of BRFS_X1 Middle hole of BRFS_X3 RFM_X7 Middle hole of RFM_X3 COMMAN (at the bottom of the cabinet) COMMAN (at the bottom of the cabinet) External fan MPD B.20 Cable Connections in R192T Double-carrier Remote Stations Table B.20-1 Cable Connections in R192T Double-carrier Remote Stations Cable Name Connection of Terminal A Connection of Terminal B Remarks DCDX01 DCDX02 DCDX03 RSTDX BRFS_X5 MPD_X6 MPD_X7 MPD_X5 MPD_X11 MPA LNA BRFS_X6 B-23 Serial No. 1 2 3 4 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Serial No. Cable Name Connection of Terminal A Connection of Terminal B Remarks MONDX01 MONDX02 MPA CONTL DX01 DX02 DX03 DX05 DX06 ACDX03 ACDX01 ACDX02 ACDX04 F-DC PWR-001 F-DC PWR-002 F-DC PWR-003 RF25 RF33 RF34 RF36 RF38 RF40 RF41 RF42 RF43 F-FAN-005 F-FAN-006 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MPA LNA-2 MPA Door grounding point Cabinet Cabinet RFM_X24 MPD_X4 MPD_HP POWER (at the bottom of the cabinet) MONDX02_B MONDX01_B TRX Cabinet grounding point Lightning arrester Door Door status switch Power lightning arrester Heater Power lightning arrester (blue, brown) Grounding point (black) Power lightning arrester External AC power External -48V power Power lightning arrester Power lightning arrester MPD_X1 ACDX01_A POWER (at the bottom of the cabinet) F-DC PWR-001_A
(Blue) MPD_V-
(Black) MPD_V+
TRX_TX LNA-2_IN MPA_OUT TRX_RX1 RFE-ANT1 (at the bottom of the cabinet) Middle hole of BRFS_X1 Middle hole of BRFS_X3 Middle hole of RFM_X3 RFM_X7 RFE-ANT0 cabinet) EXTEND (at the bottom of the cabinet) MPA_IN MDUP1900_RX MDUP1900_TX LNA-2_RFOUT1 MDUP1900_ANT LNA-2_RFOUT2 the bottom of
(at the TRX_RX0 COMMAN (at the bottom of the cabinet) COMMAN (at the bottom of the cabinet) MPD External fan B-24 The configuration in case that AC power is supplied The configuration in case that DC power is supplied Appendix C Equipment Parameters C.1 Dimension See Fig. C.1-1 for the appearance of a micro-BTS/remote station cabinet. Fig. C.1-1 Appearance of a ZXCBTS Cabinet The dimension of the cabinet is 630mm (height)400mm (width)285mm (depth). The weight of one cabinet is 45kg. C.2 Power Consumption Refer to the following table for the power consumption of several types of micro-BTS and remote stations supplied with the 120V AC power in case of full load. C-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Table C.2-1 Power Consumption of Several Types of Micro-BTS and Remote Stations Model Power Consumption M190T M191T M192T M800T M802T R190T R191T R192T R800T R802T Power factor: 0.5 180W 195W 290W 195W 290W 180W 195W 290W 195W 290W Refer to the following table for the power consumption of several types of micro-BTS and remote stations supplied with the 120V AC power in case of full load when they are configured with heaters. Table C.2-2 Power Consumption of Several Types of Micro-BTS and Remote Stations Model Power Consumption (Watt) M190T M191T M192T M800T M802T R190T R191T R192T R800T R802T Power factor: 0.5 280W 295W 390W 295W 390W 280W 295W 390W 295W 390W Note: When the temperature is lower than -10C, a heater can be added. Currently, only the equipment supplied with 120V AC power support this function. DC equipment does not support this function. C-2 Appendix C Equipment Parameters Refer to the following table for the power consumption of several types of micro-BTS and remote stations supplied with the -48V DC power in case of full load. Table C.2-3 Power Consumption of Several Types of Micro-BTS and Remote Stations Model Power Consumption (Watt) M190T M191T M192T M800T M802T R190T R191T R192T R800T R802T 180W 195W 290W 195W 290W 180W 195W 290W 195W 290W C-3 Appendix D Indicators D.1 BDM Indicators See Fig. D.1-1 for the BDM indicators and their meanings. HL4 HL7 HL8 HL5 HL6 HL16 HL11 HL10 HL3 HL9 HL17 HL18 HL2 HL1 HL12 HL13 HL14 HL15 HL4: 3.3V power indicator HL7: 5V power indicator HL8: 12V power indicator HL3: Synchronization indicator for the first channel of E1. On: asynchronized; Off: synchronized. HL9: Synchronization indicator for the second channel of E1. On: asynchronized; Off: synchronized. HL17: Synchronization indicator for the third channel of E1. On: asynchronized; Off: synchronized. HL18: Synchronization indicator for the fourth channel of E1. On: asynchronized; Off: synchronized. HL2: EPLD running indicator. On: Normal; Off: Not written HL1: FPGA running indicator. On: Not downloaded; Off:
Downloaded. HL5: System running indicator. On: Not started; Flash slowly: Loading data; Flash fast: Running normally. HL10: Alarm indicator. Off: No alarm is generated; Flash quickly: An alarm is generated. HL6, HL16 and HL11: Reserved. HL12 ~ HL15: 10M Ethernet network running indicator. Used for debugging. Fig. D.1-1 Indicators of the BDM D.2 Indicators on Front Panel of MGPS Refer to Table D.2-1 for the indicators on the front panel of MGPS and their meanings. Table D.2-1 Indicators on the Front Panel of MGPS Indicator RUN (Green) Meaning On Off Indicates that the equipment is working normally. Indicates that the equipment is abnormal. D-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Indicator Meaning On Off WARM UP (Green) Indicates that the equipment is warming up. Indicates that the equipment is working normally. GPS ALM (Green) is that the equipment Indicates in initialization status, unlocked status or in status in which satellite signals cannot be received. If it flashes, it indicates that the GPS antenna is disconnected. Other causes 1PPS ALM (Green) Indicates that the 1PPS detection accuracy exceeds the required range (800ns). FAULT (Red) Indicates that the equipment is faulty. Check TOD messages for the cause. 10MHz (Red) No output 19.6608MHz (Red) No output PP2S (Red) No output D.3 Indicators of LFM, RFM and OIM the that 1PPS Indicates detection accuracy meets the requirement (800ns). Indicates that the equipment is working normally. Output of 10MHz Output of 19.6608MHz Output of PP2S 1. Refer to the following table for the LFM indicators and their meanings. Table D.3-1 Indicators of the LFM Indicator Meaning POWER (Red) CLKER (Red) TXCLK (Green) FIBIN (Green) RXREADY (Green) Power indicator. When it is on, it indicates that power is being supplied. Clock alarm indicator. When it is on, it indicates that no clock signal is recovered in the LFM. Tx clock indicator. When it is on, it indicates that the multiplexing chip in the LFM locks the Tx clock. Optical signal indicator. When it is on, it indicates that optical signal is entering the optical interface. Data receiving indicator. When it is on, it indicates that the LFM is recovering the data from the optical links correctly. D-2 Appendix D Indicators 2. Refer to the following table for the RFM indicators and their meanings. Table D.3-2 Indicators of the RFM Indicator Meaning HL7 ALARMCLK (Red) HL2 PLLLOST (Red) HL12 TEMP_INT (Red) HL11 OPT_DETECT (Green) HL10 DOOR (Green) HL9 SD_ALARM (Green) HL3 3.3V (Green) HL1 5V (Green) HL4 12V (Green) HL6 1032LOCK (Green) HL17 1034RDY (Green) HL8 LVDS_TEST Clock alarm indicator. When it is on, it indicates that the RFM cannot recover the 16chip clock signal from the optical links correctly. Phase-locked loop indicator. When it is on, it indicates that the phase-locked loop of the RFM is unlocked. Temperature alarm indicator. When it is on, it indicates that the temperature is too high. PP2S indicator. When it flashes every 2 seconds, it indicates that the links are normal. Door control indicator. When it is on, it indicates that the door is opened. Optical signal alarm indicator. When it is on, it indicates that no optical signal enters the optical interface. 3.3V power indicator. When it is on, it indicates that the 3.3V power is supplied normally. 5V power indicator. When it is on, it indicates that the 5V power is supplied normally. 12V power indicator. When it is on, it indicates that the 12V power is supplied normally. Tx clock indicator. When it is on, it indicates that the multiplexing chip in the RFM locks the Tx clock. Data receiving indicator. When it is on, it indicates that the RFM is recovering the data from the optical links correctly. Test indicator. It is always off. D-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual 3. See Fig. D.3-1 for the location of the indicators on the OIM panel. ZX3G1X-OIM HL2 HL5 HL1 HL6 HL3 HL4 Fig. D.3-1 Location of Indicators on the OIM Panel Table D.3-3 Indicators on the OIM Panel Indicator Meaning HL1 HL2 HL3 HL4 HL5 HL6 3.3V power indicator. When it is on, it indicates that the 3.3V power is being supplied normally; when it is off, it indicates that the 3.3V power is not available. Tx clock lock indicator. When it is on, it indicates that the Tx clock has been locked; when it is off, it indicates that the Tx clock has not been locked yet. Data receiving preparation indicator. When it is on, it indicates that the receiving preparation has been completed; when it is off, it indicates that the receiving preparation has not been completed yet. Optical signal indicator. When it is on, it indicates that optical signals are available;
when it is off, it indicates that no optical signals are available. 5V power indicator. When it is on, it indicates that the 5V power is supplied normally; when it is off, it indicates that the 5V power is not available. Data receiving error indicator. When it is on, it indicates that errors exist in the currently received data; when it is off, it indicates that the currently received data is correct. D-4 Appendix E Abbreviations Abbreviation Full Name 1X EV 1X EV-DO 1X EV-DV 1X EV-DO 24PB 2G BTS 3G BTS A AAA AAL AAL2 AAL5 Abis Interface ABS AC ACB ACCH ACCM ACIR ACK ACLR ACS AGC AH AI AICH AID AIUR AK ALC ALCAP AM AMB 1X Evolution 1X Evolution Data Only 1X Evolution Data & Voice 1X Evolution Data Optimized 24V Power Board 2G Base Transceiver Station 3G Base Transceiver Station Authentication Authorization Accounting ATM Adaptation Layer ATM Adaptation Layer type 2 ATM Adaptation Layer type 5 Abis Interfacethe interface of BSC--BTS Air Break Switch Asynchronous Capsule Amplifier Control Board Associated Control Channel Asynchronous Control Character Map Adjacent Channel Interference Ratio Acknowledgement Adjacent Channel Leakage Power Ratio Adjacent Channel Selectivity Automatic Gain Control Authentication Header Acquisition Indicator Acquisition Indicator Channel Application Identifier Air Interface User Rate Anonymity key Automatic Level Control Access Link Control Application Protocol Acknowledged Mode Attenuation Matching Board E-1 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Abbreviation Full Name AMF AMP AMR AN ANID AP APD APDU API ARM ARP ARQ AS ASC A-SGW ASN.1 AT ATM ATR ATT AUC AUTN AWGN A Interface B B-BDS BBDS BBS BCC BCCH BCFE BCH BCS BCSN BCTC BDM BDM1900 BDM800 Authentication Management Field Address Management Protocol Adaptive Multi Rate Access Network Access Network Identifiers Access preamble AC Power Distribution Module Application Protocol Data Unit Application Programming Interface ARM processor Address Resolution Protocol Automatic Repeat Request Access Stratum Access Service Class Access Signaling Gateway Abstract Syntax Notation One Access Terminal Asynchronous Transfer Mode Answer To Reset Attenuator Authentication Center Authentication token Additive White Gaussian Noise A Interface - the interface between BSC and MSC Backplane of Baseband Digital Subsystem Backplane of BDS BTS Baseband Subsystem Bear Channel Connect Broadcast Control Channel Broadcast Control Functional Entity Broadcast Channel BTS Communication Subsystem Backplane of Circuit Switch Network Backplane of Control Center Baseband Digital Module 1.9G Baseband Digital Module 800M Baseband Digital Module E-2 Appendix E Abbreviations Abbreviation Full Name BDS BER BGPS BGT BIM B-ISDN BLPA BMC BPD BPSK BPSN BPWS BRFE BRFS BS BSC BSM BSP BSS BSSAP BTM BTRX BTS BUSN BWT C CA CAMEL CB CBR CBS CC CC/PP CCCH CCF CCH CCK CCM Baseband Digital System Bit Error Ratio Backplane of GPS Block Guard Time BDS Interface Module Broadband ISDN Backplane of LPA Broadcast/Multicast Control BDS Power Distribute Binary Phase Shift Keying Backplane of Packet Switching Network Backplane of PWS Backplane of RFE Backplane of TRX and BDM/RFM Base Station Base Station Controller Base Station Management Board Support Package Base Station Subsystem Base Station Subsystem Application Part BTS Test Module Backplane of TRX Base Transceiver Station Backplane of Universal Switching Network Block Waiting Time Certificate Authentication Customized Application for Mobile network Enhanced Logic Cell Broadcast Constant Bit Rate Cell Broadcast Service Control Channel Composite Capability/Preference Profiles Common Control Channel Call Control Function Control Channel Corporate Control Key Communication Control Module E-3 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Abbreviation Full Name CCP CCPCH CDF CDMA CDR CDSU CE CEB CES CFN CGI CHAP CHM CHM-1X CHM-95 CIB CIC CLK CLKD CLKG CLNP CLNS CM CMB CMF CMIP CMIS CMM CN CNAP CPCH CPCS CPICH CPM CPP CPU CR CRC Compression Control Protocol Common Control Physical Channel Command Dispatch Functions Code Division Multiple Access Call Detail Record Channel/Data Service Unit Channel Element Channel Element Board Channel Element Subsystem Connection Frame Number Common Gateway Interface Challenge Handshake Authentication Protocol Channel Processing Module Channel Processing Module for CDMA2000 Channel Processing Module for IS-95 Circuit-bearer Interface Board Circuit Identification Code Clock Clock Distributor Clock Generator Connectionless Network Protocol Connectionless Network Service Configuration Management Combiner Connection Monitor Function Common Management Information Protocol Common Management Information Service Capability Maturity Model Core Network Calling Name Presentation Common Packet Channel Common Part Convergence Sublayer Common Pilot Channel Calling Processing Module Core Processor Part Central Processing Unit Change Request Cyclic Redundancy Check E-4 Appendix E Abbreviations Abbreviation Full Name CRF CRNC C-RNTI CS CSCF CS-GW CSM CSM5000 CSU/DSU CTCH CTDMA CTML C-TPDU D D_K D_M D_S D_V DAC DAD DBS DC DCA DCCH DCH DCM DCS DDI DECT DFSM DHCP DHO DIF DIU DL DLC DN DNS Command Resolution Function Controlling Radio Network Controller Cell Radio Network Temporary Identity Circuit Switched Call Server Control Function Circuit Switched Gateway Cell Site Modem Cell Site Modem ASIC 5000 Channel Service Unit/ Digital Service Unit Common Traffic Channel Code Time Division Multiple Access Common Trunking Message Link Command TPDU DBS Kernel Module D_Method D_Service D_View Digital-to-Analog Converter Destination Address Database Subsystem Dedicated Control (SAP) Dynamic Channel Allocation Dedicated Control Channel Dedicated Channel Dispatching Client Module Dispatching Client Subsystem Direct Dial In Digital Enhanced Cordless Telecommunication Dispatching Frame Selector Module Dynamic Host Configuration Protocol Diversity Handover Data Intermediate Frequency Module Digital Interface Module Downlink (Forward Link) Data Link Control Destination Network Directory Name Service E-5 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Abbreviation Full Name DO DOI DPC DPCCH DPCH DPDCH DRAC DRC DRNC DRNS DRX DSA DS-CDMA DSCH DSM DSS D-CN D-SN DTB DTCH DTI DTMF DTX DUP E EDC EF EHB E-HLR EIRP EJB EMC EMI EMS ESB ESD ESP ESU Data Object Domain of Interpretation Destination Point Code Dedicated Physical Control Channel Dedicated Physical Channel Dedicated Physical Data Channel Dynamic Resource Allocation Control Data Rate Control Drift Radio Network Controller Drift RNS Discontinuous Reception Digital Signature Algorithm Direct Sequence-Code Division Multiple Access Downlink Shared Channel Data Service Module Dispatching SubSystem Dispatching Control Node Dispatching Serving Node Digital Trunk Board Dedicated Traffic Channel Digital Trunk Interface Element Dual Tone Multiple Frequency Discontinuous Transmission Duplexer Error Detection Code byte Elementary File Ethernet HUB Board Enhanced HLR Equivalent Isotropic Radiated Power Enterprise Java Beans Electromagnetic Compatibility Electromagnetic Interference Electromagnetic Susceptibility Ethernet Switch Board Electrostatic discharge Encapsulating Security Payload Extended Subscriber Unit E-6 Appendix E Abbreviations Abbreviation Full Name ETSI ETU F F/R-CCCH F/R-DSCH F/R-DCCH F/R-FCH F/R-PICH F/R-SCCH F/R-SCH FA FAC FACH F-APICH F-ATDPICH FAUSCH FAX F-BCCH FBI F-CACH FCI FCP F-CPCCH FCS FD FDD FDMA FE FEC FER Flexible-Rate FLPC FM FN FNUR FP F-PCH F-QPCH European Telecommunications Standards Institute Elementary Time Unit Forward / Reverse Common Control Channel Forward/Reverse Dedicated Signaling Channel Forward / Reverse Dedicated Control Channel Forward / Reverse Fundamental Channel Forward / Reverse Pilot Channel Forward / Reverse Supplemental Code Channel Forward / Reverse Supplemental Channel Foreign Agent Foreign Agent Challenge Forward Access Channel Forward-Dedicated Auxiliary Pilot Channel Forward-Auxiliary Transmit Diversity Pilot Channel Fast Uplink Signaling Channel Facsimile Broadcast Control Channel Feedback Information Forward-Common Assignment Channel File Control Information Flow Control Protocol Forward-Common Power Control Channel Frame Check Sequence Full Duplex Frequency Division Duplex Frequency Division Multiple Access Front End Forward Error Correction Frame Erasure Rate/Frame Error Rate Flexible Data Rate Forward Link Power Control Fault Management Frame Number Fixed Network User Rate Function Point Forward-Paging Channel Forward-Quick Paging Channel E-7 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Abbreviation Full Name FS FSB F-SYNCH FTB FTC F-TDPICH FTP G GCM GID1 GID2 GMSC GMSK GoTa GP GPCM GPRS GPS GPSR GPSTM GRE GSM GSN GTP H HA HCS HDLC HDR HHO HIRS HLR HN HO HPA HPS HRPD HRR Frequency Synthesizer Frequency Synthesizer Board Forward-Synchronous Channel Fiber Transceiver Board Forward Traffic Channel Forward-Transmit Diversity Pilot Channel File Transfer Protocol GPS Control Module Group Identifier (level 1) Group Identifier (level 2) Gateway MSC Gaussian Minimum Shift Keying Global open Trunking Architecture Guard Period General Purpose Chip-select Machine General Packet Radio Service Global Position System Global Position System Receiver GPS Timing Module Generic Routing Encapsulation Globe System of Mobile Communication GPRS Support Nodes GPRS Tunneling Protocol Home Agent Hierarchical Cell Structure High-level Data Link Control High Data Rate Hard Handover High-speed Interconnect Router Subsystem Home Location Register Home Network Handover High Power Amplifier Handover Path Switching High Rate Packet Data Handover Resource Reservation E-8 Appendix E Abbreviations Abbreviation Full Name High Speed Circuit Switched Data Home Subscriber Server HW-signal process Board Input/Output Information Block Intergroup Coordination Integrated Circuit Card Incoming Call Gateway Identifier International Electrical Commission Internet Engineering Task Force Intermediate Frequency Information Field Sizes Information Field Size for the UICC Information Field Size for the Terminal Integrated Circuit Interface Circuit Internet Key Exchange Intermodulation Inverse Multiplexing on ATM IMA Board International Mobile Equipment Identity International mobile group identity International Mobile Subscriber Identity International Mobile Telecommunications 2000 International Mobile User Number Intelligent Network Intelligent Network Application Part Information Field Internet Protocol IP Process Board IP Control Protocol IP-Multicast IP Security Internet Security Association and Key Management Protocol Interference Signal Code Power Integrated Services Digital Network International Standardization Organization HSCSD HSS HWB I I/O I-Block IC ICC ICGW ID IEC IETF IF IFS IFSC IFSD IIC IKE IM IMA IMAB IMEI IMGI IMSI IMT-2000 IMUN IN INAP INF IP IPB IPCP IP-M IPSec ISAKMP ISCP ISDN ISO E-9 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Abbreviation Full Name ISP ISUP ITU IUI IWFB J J2EE JAR file JD JDMK JMS JNDI JP JTAPI JTS JVM K kbps ksps L L1 L2 L3 L3Addr LAC LAI LAN LATA LCD LCF LCP LCS LFM LLC LMF LMT LN LNA Internet Service Provider ISDN User Part International Telecommunications Union International USIM Identifier InterWorking Function Board Java 2 Platform Enterprise Edition Java Archive File Joint Detection Java Dynamic Management Kit Java Message Service Java Naming Directory Interface Joint Predistortion Java Telephony Application Programming Interface Java Transaction Service Java Virtual Machine kilo-bits per second kilo-symbols per second Layer 1 (physical layer) Layer 2 (data link layer) Layer 3 (network layer) Layer 3 Address Link Access Control Location Area Identity Local Area Network Local Access and Transport Area Low Constrained Delay Link Control Function Link Control Protocol Location Services Local Fibre Module Logical Link Control Local Management Function Local Management Terminal Logical Name Low Noise Amplifier E-10 Appendix E Abbreviations Abbreviation Full Name LOMC LPA LPF LSB M M&C MA MAC MAF MAHO MAP MCC MCE Mcps MCU MDIV MDIV800 MDN MDS MDUP MDUP800 ME MEHO MER MF MGCF MGCP MGPS MGW MHEG MHz MIB MIF MIN MIP MIPS MIT MLNA Local OMC Linear Power Amplifier Low Pass Filter Least Significant Bit Monitor and Control Multiple Access Message Authentication Code (encryption context) Management Application Features Mobile Assisted Handover Mobile Application Part Mobile Country Code Module Control Element Mega-chips per second Media Control Unit Micro Diversity 800M Micro Diversity Mobile Directory Number Multimedia Distribution Service Micro Duplex 800M Micro Duplex Mobile Equipment Mobile Evaluated Handover Message Error Rate Mediation Function Media Gateway Control Function Media Gateway Control Part Micro GPS Media GateWay Multimedia and Hypermedia Information Coding Expert Group Mega Hertz Management Information Base Management Information Function Mobile Identification Number Mobil IP Million Instructions Per Second MO Instance Tree Micro Low Noise Amplifier E-11 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Abbreviation Full Name MLNA800 MM MMI MML MNC MNIC MNP MO MOF MOHO MONB MOS MPA MPA800 MPB MPC8260 MPC860 MPD MPM MRB MRF MS MSB MSC MSG MSID MSIN MSM MSP MSU MT MTBF MTP MTP3-B MTRX800 MTSI MUI N 800M Micro Low Noise Amplifier Mobility Management Man Machine Interface Man Machine Language Mobile Network Code Multi-service Network Interface Card Mobile Number Portability Mobile Originated MO administration Function Mobile Originated Handover Monitor Board Mean Opinion Score Micro Power Amplifier 800M Micro Power Amplifier Main Process Board Motorola Power PC 8260 Motorola Power PC 860 Micro-BTS Power Distribution MSC Processing Module Media Resource Board Media Resource Function Mobile Station Most Significant Bit Mobile Switching Center Management Steering Group Mobile Station Identifier Mobile Station Identification Number Message Switching Module Multiple Subscriber Profile Main Subscriber Unit Mobile Termination Mean Time Between Failures Message Transfer Part Message Transfer Part level 3 800M Micro Transmitter & Receiver Master To Slave Interface Mobile User Identifier E-12 Appendix E Abbreviations Abbreviation Full Name NAD NAI NAS NBAP NCK NCM NDC NDUB NE NEF NEHO NEMF NIM NITZ NMC NMSI NNI NO NP NPA NPI NRT NSAP NSCK NSDU NSS NW O O&M O_AMP O_CMP O_PMP O_RMP O_TMP OCCCH ODCCH ODCH ODMA Node Address byte Network Access Identifier Non-Access Stratum Node B Application Part Network Control Key Network Control Module National Destination Code Network Determined User Busy Network Element Network Element Function Network Evaluated Handover Network Element Mediation Function Network Interface Module Network Identity and Time Zone Network Management Center National Mobile Station Identifier Network-Node Interface Network Operator Network Performance Numbering Plan Area Numbering Plan Identifier Non-Real Time Network Service Access Point Network Subset Control Key Network Service Data Unit Network Subsystem Network Operations and Maintenance O&M _Alarm Management Part O&M _Configuration Management Part O&M _Performance Management Part O&M _Right Management Part O&M _Test Management Part ODMA Common Control Channel ODMA Dedicated Control Channel ODMA Dedicated Channel Opportunity Driven Multiple Access E-13 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Abbreviation Full Name ODTCH OIB OIM OMC OMF OMI OMM OMS OO OOF OPD OPF OPRM OPTM OSA OSF OSS OSS_CLP OSS_FMP OSS_RSP OSS_SCP OSS_SWD OVSF OWB P PA PAB PACA PAM PAP PBP PC PCB PCCC PCCH PCCPCH PCF PCH ODMA Dedicated Traffic Channel Optical Interface Board Optical Interface Module Operation Maintenance Centre Operation Maintenance Function Operation Maintenance Interface Operation Maintenance Module Operation & Maintenance Subsystem Object-Oriented Operation Outputting Function Organization Process Definition Organization Process Focus Optical Receiver Module Optical Transmitter Module Open Service Architecture Operations Systems Function Operating Systems Subsystem OSS_Communicating Link Part OSS_File Management Part OSS_Running Support Part OSS_Status Control Part OSS_Software Download Orthogonal Variable Spreading Factor Order Wire Board Power Amplifier Power Amplify Board Priority Access and Channel Assignment Power Alarm Module Password Authentication Protocol Paging Block Periodicity Power Control Protocol Control Byte Parallel Concatenated Convolution Code Paging Control Channel Primary Common Control Physical Channel Packet Control Function Paging Channel E-14 Appendix E Abbreviations Abbreviation Full Name PCMCIA PCP PCPCH PCS PCU PD PDB PDC PDCP PDF PDN PDP PDR PDS PDSCH PDSN PDU PERT PG PHB PHR PHS PHY PhyCH PI PICH PID PIM PIN PL PLMN PM PMD PMM PN PNP POMC POTS Personal Computer Memory Card International Association Packet Consolidation Protocol Physical Common Packet Channel Personal Communication System Packet Control Unit Power Divider Process Database PTT Dispatching Client Packet Data Convergence Protocol Detecting of Power Direction Forward Public Data Network Packet Data Protocol Detecting of Power Direction Reverse PTT Dispatching Server Physical Downlink Shared Channel Packet Data Serving Node Protocol Data Unit Program Evaluation and Review Technique Processing Gain Per Hop Behavior PTT Home Register Personal Handy phone System Physical layer Physical Channel Page Indicator Pilot Channel Packet Identification Power Amplifier Interface Module Personal Identifying Number Physical Layer Public Land Mobile Network Project Manager Physical Layer Medium Dependent Power Monitor Module Pseudo Noise Private Numbering Plan Province OMC Plain Old Telephone Service E-15 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Abbreviation Full Name PP2S PPM PPP PPS PR PRACH PRE PRM PS PSB PSC PSCH PSE PSI PSM PSN PSOS PSPDN PSTN PTM PTM-G PTM-M PTP PTT PUSCH PVD PWRD PWS Q QA QAF QC QoS QPM QPSK QXF R R_CLP Protocol Process Module Point-to-Point Protocol Protocol and Parameter Select (response to the ATR) Peer Reviews Physical Random Access Channel Pre-amplifying Board Power Rectifier Module Packet Switched Power Splitter Board Primary Synchronization Code Physical Shared Channel Personal Service Environment PCF Session ID Power Supplier Module Packet Switched Network Public Switched Packet Data Network Public Switched Telephone Network Power Transition Module PTM Group Call PTM Multicast Point to point Push to Talk Physical Uplink Shared Channel Power VSWR Detect Board POWER Distributor Power System Quality Assurance Q3 Adaptor Function Quality Control Quality of Service Quantitative Process Management Quadrature Phase Shift Keying Qx Interface Function R_Communication Link Part E-16 Appendix E Abbreviations Abbreviation R_CLP_InSubsystem R_CLP_InterSubsystem R_CLP_MasterSlave R_CLP_TrafficData R_FMP R_FMP_Background R_FMP_Foreground R_RSP R_RSP_AbnormityProcess R_RSP_MemoryManagement R_RSP_ProcessCommunication R_RSP_ProcessDispatch R_RSP_StartupConfigration R_RSP_SystemObservation R_RSP_Timer Management R_SCP R_SCP_Boot R_SCP_MainControl R_SCP_StatusControlManagement RA RAB RAC R-ACH RACH RADIUS RAI RAN RANAP RB R-Block RC RDF R-EACH RF RFCM RFE RFF RFIM Full Name R_File Management Part R_Running Support Part R_System Control Part Routing Area Reverse Activity Bit Reverse Access Channel Access Channel Random Access Channel Remote Authentication Dial-In User Service Routing Area Identity Radio Access Network Radio Access Network Application Part Radio Bearer Receive-ready Block Radio Configuration Resource Description Format Enhanced Access Channel Radio Frequency RF Control Module Routing Functional Identity RF Filter RF Interface Module E-17 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Abbreviation Full Name RFM RFM1900 RFM800 RFS RIM RL RLC RLCP RLP RMI RMM RN RNC RNS RNSAP RNTI ROI RPB RPC RPD RPT RRC RRI RRM RRP RRQ RSA RSCP R-SGW RSM RSSI RST RSVP RT RTC RTOS RTP R-TPDU Remote Fiber Module 1.9G Remote Fiber Module 800M Remote Fiber Module Radio Frequency Subsystem RF Interface Module Radio Link Radio Link Control Radio Link Control Protocol Radio Link Protocol Remote Method Invocation RF Management Module Radio Network Radio Network Controller Radio Network Subsystem Radio Network Subsystem Application Part Radio Network Temporary Identity Return On Investment Router Protocol Process Board Reverse Power Control RFS Power Distribute Repeater Radio Resource Control Reverse Rate Indication Radio Resource Management Mobile IP Registration Reply Mobile IP Registration Request Rivest-Shamir-Adleman public key algorithm Received Signal Code Power Roaming Signaling Gateway Reverse Switch Module Received Signal Strength Indicator Reset Resource Reservation Protocol Real Time Reverse Traffic Channel Real Time Operate System Real Time Protocol Response TPDU E-18 Appendix E Abbreviations Abbreviation Full Name RU RUM RUP RX RXB S S/N S_BSSAP S_CCHSP S_CEC S_CEM S_MTP S_MTP3 S_RCM S_SCCP S_SVLP S_TCHL2P S_TCHL3P S_TLH S_VIM SA SAAL SACCH SAD SAM SAP SAPI SAR SB S-Block SC SCC SCCB SCCH SCCP SCCPCH SCE SCH Resource Unit Route Update Message Route Update Protocol Receiver Receiver Board Signal/Noise SPS Base Station System Application Part SPS Control Channel Signaling Process SPS Channel Element Controller SPS Channel Element Modem SPS Message Transfer Part SPS Message Transfer Part3 SPS Radio Channel Control Management SPS Signaling Connection Control Part SPS Selector Vocoder Low-Layer Process SPS Traffic Channel Layer2 Process SPS Traffic Channel Layer3 Process SPS Traffic Link Handler SPS Vocoder Interface Module Security Association Signaling ATM Adaptation Layer Slow Associated Control Channel Source Address Site Alarm Module Service Access Point Service Access Point Identifier Segmentation and Reassembly Storage Battery Supervisory Block Synchronous Capsule Serial Communication Controller Software Configuration Control Board Synchronization Control Channel Signaling Connection Control Part Secondary Common Control Physical Channel Software Capability Evaluation Synchronization Channel E-19 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Abbreviation Full Name SCI SCM SCP SCS SCWLL SDCCH SDF SDH SDHB SDL SDP SDTB SDU SF SHA SHCCH SIE SIM SINR SIP SIR SLA SLP SMC SME SMF SMP SMS SMS-CB SN SNM SNP SPB SPLL SPS SQN SR1 SS7 Subscriber Controlled Input Sub-BDS Control Module Session Configuration Protocol System Control Subsystem Super CDMA Wireless Local Loop Stand-Alone Dedicated Control Channel Service Discovery Function Synchronous Digital Hierarchy SDH Board Specification & Description Language Software Development Plan Sonet Digital Trunk Board Service Data Unit Spreading Factor Secure Hash Algorithm Shared Control Channel Sector Interface Element GSM Subscriber Identity Module Signal-to-Interface plus Noise ratio Session Initiated Protocol Signal-to-Interference Ratio Service Level Agreement Signaling Link Protocol Serial Management Controller Short Message Entity Session Management Function Session Management Protocol Short Message Service SMS Cell Broadcast Serving Network Switching Network Module Signaling Network protocol Signaling Process Board System Phase Locked Loop Signaling Process Subsystem Sequence Number Spreading Rate 1 Signaling System No.7 E-20 Appendix E Abbreviations Abbreviation Full Name STC STDL STTD SVBS SVC SVE SVICM SVM SVP SVPM SVPP T TCH TCM TCP TCP/IP TD-CDMA TDD TDMA TE TFM TFS TLLI TLS TMB TMN TMSI TN TOD TPC TPDU TPTL TrCH TRX T-SGW TSM TSNB TSTD Signaling Transport Converter Shared Trunking Data Link Space Time Transmit Diversity Selector & Vocoder Bank Subsystem Switched virtual circuit Selector & Vocoder Element Selector & Vocoder Interface Control Module Selector & Vocoder Module Selector & Vocoder Processor Selector & Vocoder & PCF Module Selector & Vocoder & PCF Processor Traffic Channel Technology Change Management Transmission Control Protocol Time Division-Code Division Multiple Access Time Division Duplex Time Division Multiple Access Terminal Equipment Timing Frequency Module Timing & Frequency Subsystem Temporary Link Level Identity Transport Layer Security Traffic Manage Board Telecommunication Management Network Temporary Mobile Subscriber Identity Termination Node Time of Date Transmit Power Control Transfer Protocol Data Unit Transmission Power Track Loop Transport Channel Transmitter and Receiver Transport Signaling Gateway Transmit Switch Module TDM Switch Network Board Time Switched Transmit Diversity E-21 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual Abbreviation Full Name TTI TX TXB U UDP UDR UE UI UICC UIM UL ULB UM UMS UMTS Um Interface UNI UPT URI URL USCH UT UTRA UTRAN V VA Variable-Rate VASP VBR VBS VC VCO VGCS VHE VLR VMS VoIP VPLMN Transmission Timing Interval Transmitter Transmitter Board User Datagram Protocol User Data Record User Equipment User Interface Universal Integrated Circuit Card Universal Interface Module Uplink (Reverse Link) Universal LED Board Unacknowledged Mode User Mobility Server Universal Mobile Telecommunications System Um Interface-the interface between MS and BTS User-Network Interface Universal Personal Telecommunication Uniform Resource Identifier Uniform Resource Locator Uplink Shared Channel Universal Time Universal Terrestrial Radio Access Universal Terrestrial Radio Access Network Voice Activity factor Variable Data Rate Value Added Service Provider Variable Bit Rate Voice Broadcast Service Virtual Circuit Voltage Control Oscillator Voice Group Call Service Virtual Home Environment Visitor Location Register Voice Mail Server Voice Over IP Visited Public Land Mobile Network E-22 Appendix E Abbreviations Abbreviation Full Name VPM VPN VSWR VTC W WAE WAP WCDMA WCF WDP WIN WPB WSF WSP WTA WTAI WTLS WTP X XRES Z ZXCBTS M800T ZXCBTS M802T ZXCBTS M190T ZXCBTS M191T ZXCBTS M192T ZXCBTS R800T ZXCBTS R802T ZXCBTS R190T ZXCBTS R191T ZXCBTS R192T VLR Processing Module Virtual Private Network Voltage Standing Wave Ratio Voice Transcoder Card Wireless Application Environment Wireless Application Protocol Wideband Code Division Multiple Access Workstation Control Function Wireless Datagram Protocol Wireless Intelligent Network Wireless Protocol Process Board Workstation Function Wireless Session Protocol Wireless Telephony Applications Wireless Telephony Applications Interface Wireless Transport Layer Security Wireless Transaction Protocol Expected user Response ZTE CDMA 800M micro base station (10W) ZTE CDMA 800M micro base station (20W) ZTE CDMA 1900M micro base station (5W) ZTE CDMA 1900M micro base station (10W) ZTE CDMA 1900M micro base station (20W) ZTE CDMA 800M RF remote base station (10W) ZTE CDMA 800M RF remote base station (20W) ZTE CDMA 1900M RF remote base station (5W) ZTE CDMA 1900M RF remote base station (10W) ZTE CDMA 1900M RF remote base station (20W) E-23
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2005-05-25 | 870.66 ~ 879.36 | TNB - Licensed Non-Broadcast Station Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2005-05-25
|
||||
1 | Applicant's complete, legal business name |
ZTE Corporation
|
||||
1 | FCC Registration Number (FRN) |
0009043175
|
||||
1 | Physical Address |
ZTE Plaza, Hi-tech Park, Nanshan District
|
||||
1 |
Shenzhen, Guangdong, N/A 518057
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
b******@baclcorp.com
|
||||
1 | TCB Scope |
B1: Commercial mobile radio services equipment in the following 47 CFR Parts 20, 22 (cellular), 24,25 (below 3 GHz) & 27
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
Q78
|
||||
1 | Equipment Product Code |
ZXCBTS802T
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
Y******** X****
|
||||
1 | Title |
Product Certification Manager
|
||||
1 | Telephone Number |
0086-********
|
||||
1 | Fax Number |
0086-********
|
||||
1 |
x******@zte.com.cn
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TNB - Licensed Non-Broadcast Station Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | CDMA Micro Base Transceiver Station | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | The power listed is conducted. The antenna(s) used for this transmitter must be fixed-mounted on outdoor permanent structures. RF exposure compliance is adressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of 1.1307(b)(3) | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bay Area Compliance Laboratory Corp. (Shenzhen)
|
||||
1 | Name |
J******** C********
|
||||
1 | Telephone Number |
08675******** Extension:
|
||||
1 | Fax Number |
08675********
|
||||
1 |
j******@baclcorp.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 22H | 870.66000000 | 879.36000000 | 20.0000000 | 1.5000000000 ppm | 1M25G1D |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC