ZXHN H168NW User Manual ZXHN H168NW User Manual Document Version: 20130327-R1.2 Copyright 2013 ZTE Corporation All rights reserved. No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any means without the prior written permission of ZTE Corporation. ZTE CORPORATION reserves the right to modify this manual for product upgrade or other causes without notifying users in advance. Limited warranty ZTE warrants that, for one year from the date of delivery by ZTE to purchaser's designated carrier, the Equipment will remain free from defects in design, material and workmanship under normal use and service and will conform in all material respects to the in purchase order or applicable specifications set forth agreement; ZTE does not warrant that operation of the Equipment will be error-free or uninterrupted. In accordance with ZTE's standard, warranty terms, ZTE shall, at its option, repair or replace any defective or nonconforming item, provided that (a) purchaser/End User gives ZTE written notice of the defect or nonconformity within the warranty period specified above promptly after Reseller is notified by the End User of the same; and (b) End User returns the defective item at its expense to ZTEs nominated Customer Service Department in accordance with ZTEs standard parts exchange procedures. instructions or procedures;
This warranty does not apply to defects or errors in the Equipment caused by:(a) reasonable abrasion of equipments;
(b)End Users failure to follow ZTEs installation, operation or
(c) End Users maintenance mishandling, misuse, negligence, or installation, deinstallation, storage, servicing or operation of the Equipment;
(d) modifications or repairs not made by ZTE or a ZTE-certified individual;(e) power failures, surges, fire, flood, accident, actions of third parties or other events outside ZTEs reasonable control.
(f) usage of products of third Parties, or usage conjunction with improper i ZXHN H168NW User Manual to is due that such defects third parties provided the conjunction;(g) any other cause beyond the range of normal usage for equipments. End User shall assure that Equipment is installed and maintained by ZTE or ZTE-certified individuals in accordance with ZTEs certification procedures; provided that if End User causes or permits services to be provided by individuals who are not ZTE-certified, the Warranty shall be void as to all Equipment serviced in breach of this sentence. End User shall have no right to reject, return, or receive a refund for any Equipment from ZTE. Any item repaired or replaced by ZTE shall continue to be warranted for the longer of the remainder of the original warranty period or 90 days from the date the repaired or replaced part is delivered to the carrier. FOR SOLE LIABILITY DEFECTIVE THIS WARRANTY (1) IS END USER'S SOLE REMEDY AND ZTES OR NONCONFORMING ITEMS , AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, UNLESS OTHERWISE REQUIRED UNDER THE MANDATORY PROVISIONS OF THE CHINESE LAW, AND (2) IS BETWEEN ZTE AND END USER (AS THE ORIGINAL PURCHASER FOR END USE) AND MAY NOT BE TRANSFERRED OR ASSIGNED, BY OPERATION OF LAW OR OTHERWISE, WITHOUT ZTES PRIOR WRITTEN CONSENT. Limitation of Liability ii ZXHN H168NW User Manual ZTE SHALL NOT BE LIABLE FOR ANY LOSS OF PROFITS OR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM OR ARISING OUT OF OR IN CONNECTION WITH USING OF THIS PRODUCT, WHETHER OR NOT ZTE HAD BEEN ADVISED, KNEW OR SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, COST OF CAPITAL, COST OF SUBSTITUTE FACILITIES OR EQUIPMENT, ANY DOWNTIME COSTS OR CLAIMS OF END USERS. THE LIABILITY OF EACH PARTY UNDER THIS AGREEMENT, WHETHER ARISING OUT OF BREACH OF CONTRACT (INCLUDING BUT NOT LIMITED TO BREACH OF WARRANTY) OR TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE AND STRICT LIABILITY) OR UNDER AN INDEMNIFICATION PROVISION SHALL IN NO EVENT EXCEED THE AGGREGATE AMOUNT BENIFITED BY ZTE IN THE PRODUCTS FROM WHICH SUCH LOSS OR DAMAGE DIRECTLY AROSE. Confidentiality End User agrees that End User will receive confidential or proprietary information (Confidential Information) in connection with the purchase and deployment of ZTE Equipment. End User will not disclose ZTEs Confidential Information, will use it only for purposes for which it was disclosed, and must treat it with the same degree of care as it does its own similar information, but with no less than reasonable care. End User agrees that the iii ZXHN H168NW User Manual terms herein, the Equipment and all ZTE documentation is ZTE Confidential Information. iv Contents Chapter 1 Safety Instructions........................................................... 1 1.1 Safety Checklist .................................................................. 1 1.2 Safety Instructions............................................................... 1 Chapter 2 Overview .......................................................................... 3 2.1 Features ............................................................................. 3 2.2 Product Specifications ......................................................... 3 2.3 Packing List ........................................................................ 4 2.4 System Requirements ......................................................... 4 Chapter 3 Installation Preparations ................................................. 6 3.1 Hardware Description .......................................................... 6 3.2 Hardware Connections ...................................................... 11 Appendix A FAQs ........................................................................... 14 Chapter 1 Safety Instructions 1.1 Safety Checklist Check the following items before installing the ZXHN H168NW VDSL2 equipment. 1. Electrical Safety Do not place inflammable, conductive or /wet objects around the equipment. Cables should be in good condition. All electrical appliances should be placed stably. 2. Equipment Placement Devices should be placed in a well-ventilated environment. Devices should be placed on a stable and flat surface. Do not expose the equipment to direct sunlight; do not place the equipment on a computer. Keep the equipment away from heat and water. Make sure power supply is available. The input voltage fluctuation range must be smaller than 10%. The power plug must not share the same socket with that of any hair drier, iron or refrigerator. 1.2 Safety Instructions Read the User Manual carefully before operating the equipment. Attention is required for all the safety cautions in this manual and the ZXHN H168NW V1.0 Maintenance Management Manual. Do not use any accessory that does not belong to the equipment without prior permission of the manufacturer because it may lead to equipment damage or even fire. Use the power adapter in the equipment package. Do not connect phones to the VDSL2 line directly but connect them to the splitter. Do not place any objects on the equipment. Install the equipment in a dry, well-ventilated, rainproof, and clean place. 1 ZXHN H168NW User Manual Unplug the power cables during thunderstorms to protect the equipment from lightning strikes. Clean the equipment by using a soft and dry cloth. Power off the equipment before cleaning it. Power off the idle equipment. Keep the ventilation hole clean and prevent any objects from dropping into the equipment through the hole; otherwise, a short circuit may occur, which leads to equipment failure or fire. Do not spray liquid on the surface of the equipment. Do not open the chassis by yourself, especially when the equipment is power on. Make sure the power is off before plugging/unplugging the Be careful when unplugging the switch as the transformer Keep the equipment and all its parts/accessories out of switch. may be very hot. childrens reach. RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d = 20 cm between the device and the human body. To fulfill the RF exposure requirement, a separation distance of 20 cm between the device and human must be maintained. Note:
Please read the above safety instructions carefully before operating the equipment. Users should assume responsibilities for any accidents occurred due to misconducts against the above instructions. 2 Chapter 2 Overview The ZXHN H168NW is a VDSL2 and GE access device that supports multiple line transmission modes. At the user end, it provides four 10/100/1000Base-T Ethernet interfaces, one USB 2.0 Host port, and the wireless high 400mW power. With the high-power VDSL2 and GE access the ZXHN H168NW can provide Internet service or enterprise network access service for users. 2.1 Features As a VDSL2 Modem with the routing function, the ZXHN H168NW Modem has the following features:
Supports VDSL2 with GE uplink. Supports G.992.1 (G.DMT), G.992.3 (ADSL2), G.992.5 the broadband functions,
(ADSL2+). Supports G.993.2 (VDSL2), up to 17a profile. Supports 802.11b, 802.11g, 802.11n. Supports 802.11n Wi-Fi up to 300 Mbps. Supports high power Wi-Fi with 400mW EIRP. Supports 4 GE ports. Supports USB 2.0 for shared storage or 3G Dongle. Supports Web-based configuration and monitoring. Supports bridging/routing mode. Supports NAT. Supports DHCP Client/DHCP Server. Supports Built-in DLNA Digital Media Server (DMS). Supports Robust remote management - TR069 Supports IPv4/IPv6 dual stacks 2.2 Product Specifications Environmental requirements Environment temperature: 0C - 40C (32F-104F) 3 ZXHN H168NW User Manual Humidity: 5% - 95% (non-condensing) Power adapter specifications Input: 100 240 V AC, 50/60 Hz Output: 12 V DC, 2 A Certification FCC, UL, Wi-Fi This product is designed to provide 24-hour continuous triple-play services. 2.3 Packing List ZXHN H168NW 1 Splitter 1 Power adapter 1 RJ-11 telephone cable 2 RJ-45 Ethernet cable 1 User Ma nua l ( Inc luding Qua lity Warra nty Ca r d a nd Certificate of Quality) 1 CD (Optional) 1 Note: Information provided above is for reference only; actual external view of the product may vary. Note:
The power adapter used for the ZXHN H168NW must match. 2.4 System Requirements Please check the following items before installing the ZXHN H168NW. 1. VDSL2 Service Subscription 4 ZXHN H168NW User Manual is recommended If you have subscribed to the VDSL2 service, your VDSL2 operator will provide you at least one valid IP address through static allocation or dialup dynamic allocation. 2. Computer Configuration Please make sure that the system is equipped with a 10M/100M Ethernet adapter and supports the TCP/IP protocol. It the below to use a computer with configurations: Pentium III or a later version, a minimum of 64M memory, a minimum of 10G hard disk, a graphic accelerating adapter with above 2M display memory, an audio adapter, and a sound box. 3. Operating System The operating system can be one of the following: Windows 98SE, Windows Me, Windows 2000, Windows XP, Windows Vista, Windows 7, or Windows 8. The Internet Explorer 6.0 or a later version can be used to configure the device. 5 Chapter 3 Installation Preparations 3.1 Hardware Description Front Panel Figure 3.1-1 Front Panel of the ZXHN H168NW Table 3.1-1 Descriptions of the LEDs on the Front Panel Identification Color Green
/Red Green Power DSL GE WAN Green Description Power off. POST: Power on and self-testing Firmware upgrading. The power is on and the self-test is complete. No signal is detected. DSL line handshaking is in progress. DSL line training is in progress. The Modem is activated. Ethernet link is off or the link is disconnected. The Ethernet port is in communication status. Status Off Red On Red Flash Green On Off Slow Flash Flash On Off On 6 ZXHN H168NW User Manual Identification Color Status Description Off Green Flash Internet Green
/Red Green On Green LAN1~
LAN4 Red On On Flash Off 7 is has through The system is in Bridge mode or the WAN
(DSL/GE) has not been connected. The data packets are passing the router interface on the WAN side. the The system in the Route mode and WAN been connected. The Modem IP data packets can be transmitted normally. Data packets cannot be sent or received through the route interface. (No no DHCP PPPoE response, PPPoE authentication failure, or no IP address from IPCP. The LAN is connected but no data is transmitted. A data packet is passing through LAN Interface. The not powered on or the LAN interface not connected. response, interface device the is is ZXHN H168NW User Manual Identification Color Status Description is is The wireless port enabled. Data being transmitted. The flashing frequency indicates the WLAN traffic speed. is The equipment powered off or the wireless port is disabled. The WPS function is off. The WPS function is in negotiation status. is being A the to connected gateway the WPS and the connection does not exceed 2 minutes. A USB (such as a hard disk) is plugged in. Data transmitted. The equipment is power off or no USB is plugged in. terminal through being are WLAN Green WPS Green USB Green On Flash Off Off Flash On On Flash Off 8 ZXHN H168NW User Manual Rear Panel Figure 3.1-2 Rear Panel of the ZXHN H168NW Left Panel Figure 3.1-3 Left Panel of the ZXHN H168NW 9 ZXHN H168NW User Manual Table 3.1-2 Description of Interfaces on the Rear Panel and Left Panel Specifications Item DSL LAN1-
LAN4 RJ-11 interface: The equipment is connected to the VDSL2 by a network line or a splitter through a telephone line. RJ-45 interface: It is connected to a PC or other network devices by a network cable. LED: The equipment negotiates and changes over to the gigabit mode when LED is on. The equipment negotiates to the 10/100M mode when LED is off. RJ-45 port: It is connected to the modem or other network devices. Reset WAN POWER Power interface. It is connected to the power adapter. At the power-on state, the system will be restored to the default configurations if the button is pressed over 5 seconds. USB port USB WLAN Wireless switch: The wireless LAN will be switched on if the button is pressed over 3 seconds. WPS switch: The WPS will be enabled if the button is pressed over 3 seconds. Power switch WPS On/Off 10 ZXHN H168NW User Manual 3.2 Hardware Connections Introduction:
1. Use a RJ-11 cable to connect the line port of the splitter to the RJ-11 port (the phone jack) on the wall. 2. Use another RJ-11 cable to connect the modem (or VDSL2) port of the splitter with the line port of the gateway. 3. Use the third RJ-11 cable (when the customer requires to use telephone at the same time) to connect the telephone set with the phone (or TEL) port of the splitter. 4. Connect the Ethernet port of the device with 10/100BASE-T port of the computer by using a network cable. 5. Plug in the power cord, and turn on the power. If you do not want the Internet service or telephone voice services to be provided at the same time, connect only the line port of the gateway with the RJ-11 port (the phone jack) on the 11 ZXHN H168NW User Manual wall by using a telephone cord. In this case, the splitter is not necessary. Connection Procedures 1. Power off the equipment before connecting all the other devices. 2. Connect the network cables: Plug the RJ-45 Ethernet cable connector into the Ethernet interface of the ZXHN H168NW, and connect the other terminal to the Ethernet adapter of the customer computers or ports of other network devices. 3. Connect the splitter. The splitter has three interfaces as described below:
LINE: Connects the user telephone cable (RJ11 interface). MODEM (or VDSL2): Connects the DSL interface of the ZXHN H168NW. PHONE (or TEL): Connects the phone sets. The installation process is as follows:
1). Connects the line interface of the ZXHN H168NW to the Modem (or VDSL2) interface of the splitter by using one RJ-11 telephone cable. 2). Connects the phone set lines to the Phone (or TEL) interface of the splitter. 3). Connects the user telephone cable port to the LINE interface of the splitter. 4. Connect the power supply device. 1). Connect one terminal of the power adapter to the power port of the ZXHN H168NW. 2). Connect the other terminal to the socket on the wall. 3). Switch on the power of the ZXHN H168NW. 12 ZXHN H168NW User Manual Cable Connection Checks Check cable connections as described below:
1. Check the VDSL2 cable connection If the DSL LED is on when the ZXHN H168NW is power on, it indicates that the VDSL2 line is properly connected. (Generally it takes one to two minutes to complete the VDSL2 connection). 2. Check the computer connection When both the Link LED on the computer adapter and the Ethernet LED of the ZXHN H168NW turn green, it indicates that the computer and the ZXHN H168NW equipment are properly connected. 3. Check the telephone cable connection The telephone cable is properly connected when the telephone signal reception is normal and free of noise. The telephone service is not affected no matter the ZXHN H168NW is powered on or off. 13 NO. 1 2 3 it indicates Appendix A FAQs Problem and Troubleshooting All indicators are off after the ZXHN H168NW equipment is powered on. First, make sure that you have plugged the power adapter of the ZXHN H168NW into a working power socket and that the ZXHN H168NW has been powered on (the switch button is pressed down). When the indicators are still off after the above procedures, it may be caused by hardware damage. In such a case, contact the local operator for help. Do not repair by yourself. Will VDSL2 affect the telephone conversation quality? Will the Internet access rate become slow if one is making a phone call and accessing the Internet at the same time?
VDSL2 separates voices from data through the frequency technology. Therefore, voices and data run in different paths out of interference. Neither one will deteriorate when you are in a call and on line at the same time. Issue description: Sometimes, the VDSL2 users cannot access the Internet. division multiplexing 14 ZXHN H168NW User Manual NO. 4 Problem and Troubleshooting Solution:
First, check whether the ZXHN H168NW is at normal state (check the indicators against this User Manual). If yes, check the computer or application network, not the VDSL2. If the VDSL2 Modem has problems, then check the status of indicators one by one to debug the fault. It is recommended that you check the following points before you seek help from operators:
1. The VDSL2 telephone cable connectors are in good condition. 2. The VDSL2 is away from the power cable and large-power electronic devices. 3. No telephone extensions and fax machines are installed between the VDSL2 incoming line and the splitter. 4. The splitter is correctly installed. 5. The VDSL2 Modem is not over-heated. Password verification failure. Issue description: Modem synchronization and connection are normal. However, sometimes the password fails to be verified. Solution:
1. The account and password are case sensitive and some accounts contain a domain name. 2. Virtual dialup software:
that sometimes the virtual dialup software is faulty, or conflicts with other software in the operation system. In such cases, it is suggested to re-install the dialup software or replace it with valid software. 3. Network adapter drive program may be faulty. 4. Not pay on time. Pay on time in such cases. is possible It 15 ZXHN H168NW User Manual NO. 5 link down or Problem and Troubleshooting What are the reasons for VDSL2 synchronization failure (also referred to link establishment failure)?
When the VDSL2 suddenly fails to be synchronized
(link down) during application, it might be caused by the DSL indicator of the Modem, which is not constantly On. Perform the following steps to check:
1. Check the quality of the incoming cables and the incoming cable connectors. 2. Install the VDSL2 Modem correctly by following the user guide. 3. Ensure the telephone cables are normal and are properly connected with VDSL2. 4. Disconnect the splitter and directly connect the VDSL2 Modem to the incoming customer cable end to ensure that the problem is not caused by improper installation or poor quality of the incoming customer cable. If the VDSL2 is synchronized again after that, it means that the incoming customer part is not installed properly. Re-install it according to the User Guide. 16 ZXHN H168NW User Manual NO. 6 Problem and Troubleshooting 5. When the VDSL2 still fails to be synchronized after the VDSL2 Modem has been connected to the incoming customer cable end, contact the operator to check whether there are external line failures/modem failures. 6. If the problem is caused by the splitter, call the operator to maintain. 7. The problem may be caused by the equipment provided by the operator. Call the operator to replace. 8. A long cable connecting the splitter and the VDSL2 Modem may anti-interference performance and poor synchronization. Therefore, try to keep the cable short. Why authenticated user names and passwords cannot be re-authenticated?
cause poor 17 ZXHN H168NW User Manual NO. Problem and Troubleshooting This problem may be caused by the following reasons:
1. The account has expired or it is a default account. In such cases, pay the charge. 2. In case a subscriber changes his or her residence. As the account and the path PVC might be bundled by operators, the previous account and password cannot be authenticated again. 3. The subscriber has logged in by one of his or her accounts and can not be re-authenticated because the operator recognizes the uniqueness of this account. 4. The problem may be caused by deregistration failure on the Broadband Access Server (BAS) when one is off line abnormally. The BAS or the billing system still keeps the account logged in. Therefore, the re-login fails. In such cases, re-login after logging out. In case the problem still exists, contact the operator for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 18 ZXHN H168NW User Manual in interference This equipment complies with FCC radiation exposure limits set forth for uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. to 19 ZXHN H168NW User Manual Customer Information 1. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On bottom of this equipment is a label that contains, among other information, a product identifier of US: ZTEDL01BHNH168NW. If requested, this number must be provided to the telephone company. 2. If this equipment VDSL CPE causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isnt practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. 3. The telephone company may make changes in this facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modification to maintain uninterrupted service. 4. If you experience trouble with this equipment, you disconnect it from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning. 5. Please follow instructions for repairing if any (e.g. battery replacement section); otherwise do not alternate or repair any parts of device except specified. 20 ZXHN H168NW User Manual If the telephone company requests information on what 6. Connection to party line service is subject to state tariffs. Contact the state public utility commission public service commission or corporation commission for information. 7. equipment is connected to their lines, inform them of:
The telephone number that this unit is connected to, a) The ringer equivalence number [0.1B ]
b) The USOC jack required [RJ11C], and c) The FCC Registration Number US: ZTEDL01BHNH168NW d) Items (b) and (d) are indicated on the label. The ringer equivalence number (REN) is used to determine how many devices can be connected to your telephone line. In most areas, the sum of the RENs of all devices on any one line should not exceed five (5.0). If too many devices are attached, they may not ring properly. Service Requirements In the event of equipment malfunction, all repairs should be performed by our Company or an authorized agent. It is the responsibility of users requiring service to report the need for service to our Company or to one of our authorized agents. Service can be facilitated through our office at:
Acadia Solutions, Inc.130 E. Wilson Bridge Road Suite 320 Worthington, OH 43085. Phone614-505-613 21