FCC ID: SRQ-MF256 LTE CAT6 CPE Outdoor

LTE CPE MF256 Series Quick Start Guide About this document What do you need This manual will serve as a Quick Start Guide to the LTE Device Model MF256 series. It includes two parts, an indoor unit and an outdoor unit. In this paper, the indoor unit will be replaced by Router, and the outdoor unit will be replaced by ODU. Make sure you have everything you need to properly congure the device. Panel of device WAN/PoE ODU Router POWER SUPPLY Ethernet CABLE How does it work 1. The ODU connects to the LTE network. 2. The ODU is connected to the Router, operated with Router to provide Internet sevices. 3. The ODU is power supplied by the Router with PoE. 4. The Router functions as a LAN & Wi-Fi gateway. This quick installation guide shows you how to congure your ODU and Router in order to access the Internet. Congure hardware CAUTION Before you begin, make sure that you are familiar with all accident prevention and safety procedures necessary for working at height and with electricity. DO NOT install the ODU during a lightning storm. I/O Panel of Router LTE Outdoor Unit Internet Choose Location Insert a SIM Card to the Slot CAUTION Make sure the ODU is turned o before you insert your SIM card. It is recommended to NOT connect the PoE cable you do this step. Otherwise, the SIM card may be damaged. Step 1 Remove the cover . Step 2 Insert your SIM card. LED Panel of Router I/O panel of ODU 1 PoE LTE eNB Firewall Core Network Router LAN and WAN The ODU can be mounted on an antenna pole or mast or on a wall using the supplied mounting bracket. Choose a mounting point that is sturdy enough to hold the ODU, even during high winds. When choosing a location to install the ODU, remember that the ODUs front panel should point towards your service providers nearest base station. You do not need to be able to see the base station from the ODUs position. However, if you experience diculties with signal reception, a Line of Sight (LoS) connection may produce better results. It is suggested that you transport the ODU to its intended installation location in its original protective packaging. Step 3 Insert the cable Step 4 Align and put the cover to protect it in the ODU. 2 3 4 5 6 Connect the Router to ODU Place a CAT5e Ethernet cable from the location of your intended Router to the desired ODU location. The maximum distance of the CAT5e cable is limited to 100 meters. If you use cable extenders to cover a greater distance, signal attenuation may occur. If you intend to use cable clamps or other methods to secure the cable, do not tighten them yet. Leave the cable loose until after you nish installing the Router and ODU. To connect the CAT5e Ethernet cable:

Step 1 Open the ODU cover by taking the screws from the housing. Step 2 Connect the end of the CAT5e Ethernet cable to the PoE port of the ODU. Step 3 Place the cover on the ODU housing and turn the screw. NOTE: Make sure you have inserted the SIM card into the ODU. Connect the Router Place a CAT5e Ethernet cable (not included) from the location of your intended Router to the desired ODU location. The maximum distance of the CAT5e cable is limited to 100 meters. If you use cable extenders to cover a greater distance, signal attenuation may occur. If you intend to use cable clamps or other methods to secure the cable, do not tighten them yet. Leave the cable loose until after you nish installing the Router and ODU. ODU Router Adapter Computer Hardware connections of Router Mount the ODU See the installation instructions to mount the ODU correctly. Pole mounting Pole diameter type The mounting pole diameter is from 25mm to 45mm; If the pole diameter is less than 30mm, you need to add a C-type ring to make sure the device can be mounted on the pole. The specic mounting steps are as follows:

1. Using a screwdriver to loosen the metal hose clampsthrough the terminal equipment mounting hole, the metal hose clamps and the pole is xed Step 1 Connect the CAT5e Ethernet cable to the Router WAN/PoE port. Metal hose clamps CAUTION Do not connect a computer or switch directly to the PoE port of the Router due to high PoE power. Step 2 Connect the power adapter to the Router. The POWER LED turns on a solid green-yellow once connected. Step 3 Connect the Ethernet cable from the computer to one of the Router's LAN ports. pole type mounting A 7 2. Using a screwdriver to lock the metal hose clamps, xed terminal equipment. Adjust the terminal equipment to align the direction of the base station for the best eect. LED Behavior When set up the Outdoor Unit, the LEDs of Router will have the following behavior. Congure the CPE Login to the Management page Using a screwdriver to lock the metal hose clamps pole type mounting B Note: terminal equipment cable outlet must be installed downward direction. 3. If the diameter of pole is between 25mm and 30mm, its needed to use the rubber C-type rings to add the diameter of the pole. Description Signal strength is weak LED Behavior Only rst signal LED steady on, the other three o LED illustration Signal strength is good Signal Strength is medium The rst two signal LEDs steady on, the last two o The rst three signal LEDs steady on, the last one o All signal LEDs steady on Signal strength is strong State Signal Strength weak Signal Strength medium Signal Strength good Signal Strength strong LTE Scanning LAN Disconnected The CPE is searching for a frequency channel or is performing network entry LAN Connected The CPE has a successful connection with a device on the LAN The CPE does not have an Ethernet connection with the LAN The SIM Card in abnormal state The SIM Card is Undetected The SIM Card is ready SIM card abnormal No SIM card SIM card normal SYS linked SYS no link CPE Operation Firmware Upgrading The CPE attached to LTE network The CPE not attached to LTE network The CPE is operating properly The CPE is upgrading the rmware All signal LEDs blinking simultaneously The ETH LED On The ETH LED O The SIM LED Blinking The SIM LED O The SIM LED On The SYS LED On The SYS LED O The RUN LED Blinking All signal LEDs scrolling blink one by one Using a browser to access the management web page to congure and manage the CPE. The following procedure describes how to use a computer running Windows 7 and Internet Explorer to connect to the CPE webpage. Step 1 Connect the CPE correctly. step 2 Start Internet Explorer, go to http://192.168.8.1 in the address bar, and press Enter. IP address Step 3 Enter the user name and password, and click Log In. You can connect to the management web page after the password is veried. C-type ring 8 9 10 Conguration of LTE Step 1 Connect the CPE correctly. Step 2 Enter the management website. Step 3 Choose Settings Network LTE Settings. Step 4 Set the connection mode and scan mode. LTE Settings Settings Status Connect Method Status DL MCS UL MCS DL Frequency UL Frequency Bandwidth RSSI RSRP0 RSRP1 RSRQ SINR TX Power Connected Auto 28 0 3560.0 MHz 3560.0 MHz 20 MHz

-44 dBm

-70 dBm

-72 dBm

-5 dB 32 dB 6 dBm Submit Cancel The default setting is automatically connection and full band scanning, if you want to connect the LTE network according to your needs, you can set the connection mode as manual, and simply scan a specied band. Conguration Wi-Fi Step 1 Connect the CPE correctly. Step 2 Enter the management website. Step 3 Choose Settings Wi-Fi WLAN Settings. Step 4 In the General Settings area, set Wi-Fi Enable or enable Wi-Fi with the Wi-Fi button. Step 5 In the Setting area, change the SSID, such as:

"LTE-Router"

11 Step 6 To ensure data security, it is recommended that you change the Wi-Fi password by default. Step 7 Click Submit to save the settings. WLAN Settings General Settings Band WLAN Mode Channel Tx Power SSID Profile SSID Maximum number of devices Hide SSID boradcast AP isolation Security Show password Password 2.4GHz Enable 802.11b/g/n(Auto) Auto 100%

ENTEL-HOGAR-8D6B_2.4G *

16 Enable Enable WPA2-PSK Enable

*

Fails to Log in to the web management page. Make sure that the CPE is started. Verify that the CPE is correctly connected to the computer through a network cable. If the problem persists, contact authorized local service suppliers. The CPE fails to search for the LTE network. Check that the power adapter and PoE have have connected to the CPE properly. Check that the CPE is placed in an open area that is far away from obstructions, such as concrete or wooden walls. Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic eld, such as microwave ovens, refrigerators, and satellite dishes. If the problem persists, contact authorized local service suppliers. The CPE power adapter has overheated The CPE is reheated after being used for long time. Therefore, you must turn o the CPE when not you are using. Check that the CPE is properly ventilated and protected from direct sunlight. The parameters are restored to default values. If the CPE powers o unexpectedly while being congured, the parameters may be restored to the default settings. After conguring the parameters, download the conguration le to quickly restore the CPE to the desired settings. FCC Regulations:

l This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. l This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. l Changes or modications not expressly approved by the manufacturer could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To comply with FCC RF Exposure compliance requirements, this grant is applicable to only Mobile Congurations. The antennas used for the transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Frequently Asked Questions The POWER indicator does not turn on. Make sure that the power cable is connected to the PoE, and the CPE is connected to the right port of the PoE. Make sure that the power adapter and PoE are compatible with the CPE. Notice Some features of the product and its accessories described herein rely on the software installed, capacities and settings of local network, and may not be activated or may be limited by local network operators or network service providers, thus the descriptions herein may not exactly match the product or its accessories you purchase. ZTE reserves the right to change or modify any information or specications contained in this manual without prior notice or obligation. 12 13

Model: MF256 B2/4/7/28A/28B/38/4 1/42 Device IP: 192.168.8.1 S/N:12345690123456 Wi-Fi SSID (2.4GHz): enreL-Hocar-spe4_2.4 TINIMTITTIINIIEYID TANI FE Wi-Fi SSID (5GHz): ENTEL-HOGAR-8D64_5G MAC-1234569012 WPA2-PSK: 88693712 TT Username: admin ZTE Password: admin FCC ID: SRQ-MF256 POWER RATING:24V === 1.0A MADE IN CHINA

ZTE Corporation Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2019/10/09 Subject; Request for Confidentiality FCC ID: SRQ-MF256 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description NII Software Security In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Yu Gong Title: Certification manager

ZTE Corporation Letter of Authorization SRQ-MF256 ZTE Corporation LTE CAT6 CPE Outdoor ZTE Plaza, Keji Road South, Shenzhen China Company:

Address:

Product Name:

Model Number: MF256 FCC Identifier:

We authorize MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name:

Title:

Signature of applicant:

Certification manager Date: 2019/10/09 Yu Gong