FCC ID: SRQ-MF971R LTE Ufi (LTE, WCDMA, GSM, 2.4GHz WIFI and 5GHz WiFi)

MF971R Quick Start Guide ZTE CORPORATION Postcode: 518057 NO. 55, Hi-tech Road South, Shenzhen, P.R.China 1 Getting to Know Your Device Appearance The following figure is for your reference only. 2 1. Power key your device. 2. WPS key Press and hold for about 1.5 seconds to power on/off Press and hold for about 8 seconds to restart your device. Press and hold for 1.5 seconds to activate the WPS function. 3. Indicator light 4. Charging/micro-USB jack 5. micro-SIM card slot cover and reset hole 3 Getting to Know Your Device Indicator lights Indicator Status Description Battery Wi-Fi Red solid /

The battery is low. Please blinking Green blinking Green solid charge the battery. The battery is being charged. or high. The battery level is middle Light off Your device is powered off and not being charged. Blue solid Wi-Fi is active. WPS is active. Blue blinking Light off Wi-Fi is off. messages. SMS Blue solid You have unread Blue You have new messages blinking or the message storage is full. 4 Light off There is neither an unread message nor a new message. Red The device is in error Network status. The device is not registered to the mobile network. There is no micro-SIM card inserted. There is no network service available. The device is registered to the 2G/3G mobile network. Green solid Green blinking The device is connected to the 2G/3G mobile network and data is being transferred. Blue solid The device is registered to the 4G LTE network. 5 Blue The device is connected blinking to the 4G LTE network and data is being transferred. Getting to Know Your Device Connection Scenarios The device allows multiple clients to surf on the Internet at the same time. The following figure is for your reference only. A micro-SIM card can be used to access the Internet. 6 7 Installing the micro-SIM Card 1. Open the micro-SIM card slot cover. NOTE:

device. Do not remove the cover rudely, because it is connected with the 2. Install a micro-SIM card to the micro-SIM card slot. WARNING!

To avoid damage to the device, do not use any other kind of SIM cards, or any non-standard micro-SIM card cut from a SIM card. You can get a standard micro-SIM card from your service provider. 8 3. Close the micro-SIM card slot cover. 9 Connecting to Your Device Using Wi-Fi 1. Power on your device. 2. Ensure that your computer or other client devices have enabled Wi-Fi, and search for available wireless networks. Refer to your Wi-Fi-enabled client device manual for further details on how to search for wireless networks. If you use a computer, you need to set your computer to obtain an IP address 3. Select the Wi-Fi name (SSID) of your device, and click 4. Enter the Wi-Fi password if necessary, and click OK. NOTE:

automatically. Connect. NOTE:

Refer to the chapter Getting to Know the Wi-Fi SSID and Password to get the default Wi-Fi SSID and password. 5. Wait until the client device is connected to your device successfully. Using a USB Cable 1. Connect a computer to your device with a USB cable. 2. Power on your device. The operating system detects and identifies new hardware, and automatically installs the software. 10 3. Wait until the computer is connected to your device successfully. 11 Getting to Know the Wi-Fi SSID and Password and password. You can view the label on the device to get the default Wi-Fi SSID 12 Logging in to the 4G Mobile Hotspot Configuration Page 1. Ensure that the connection between your device and the client device is correct. 2. Launch the Internet browser and enter http://192.168.0.1 or http://ufi.ztedevice.com in the address bar. 3. Enter the password to log in to the 4G Mobile Hotspot configuration page. NOTE:

View the label on the device to get the default password. 13 Changing the Wi-Fi SSID or Password 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Wi-Fi Settings. 3. Change the Network Name (SSID) or the Password in the Main SSID area. 4. Click Apply. 14 Accessing the Internet After a client device is successfully connected to your device, you can access the Internet in Automatic or Manual mode. The default mode is Automatic. Mode Operation Automatic Your device is automatically connected to the Internet, and you can surf on the Internet through the client. Manual 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select network Settings > Connection Mode > Manual, and then click Apply. 3. Click to return to the home page, and click or

. NOTES:

To change the current connection setting, please disconnect from the Internet first. To modify the parameters of your device, log in to the 4G Mobile Hotspot configuration page. 15 Configuring Your PC The following describes how to configure the Internet Protocol in Windows for your Wi-Fi connection. 1. Right-click Network and select Properties. 2. Select Change adapter settings. 3. Right-click Wireless Network Connection and select 4. Select Internet Protocol Version 4 (TCP/IPv4), and click Properties. Properties. 5. Select Obtain an IP address automatically and Obtain DNS server address automatically, and click OK. 16 Warning and Notice To the User If inadequately shielded, some electronic devices, for example, the electronic system of vehicles, may be affected by the electromagnetic interference caused by the device. Consult the manufacturers of such devices before using the device if necessary. Operating the device may interfere with medical instruments such as hearing aids and pacemakers. Always keep the device more than 20 centimeters away from such medical instruments when your device is powered on. Power off the device if necessary. Consult a physician or the manufacturers of medical instruments before using the device if necessary. Be aware of the usage limitation when using the device at places such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Power off the device if necessary. Do not use electronic transmission devices in aircraft, at petrol stations or in hospitals. Observe and obey all warning signs, and power off the device in these conditions. Do not touch the inner antenna area unless necessary. Otherwise the performance of the device may be affected. Do not use the device in an enclosed environment or where heat dissipation is poor. Prolonged work in such space may cause excessive heat and raise ambient temperature, which may lead to automatic shutdown of the device for your safety. In the case of such an event, cool the device in a well-

ventilated place before turning on for normal use. Keep the device out of the reach of small children. The device may cause an injury if used as a toy. 17 When the device is operating, do not touch the metallic parts. Failing to do so may cause burns. Use original accessories or accessories that are authorized. Using any unauthorized accessories may affect the performance of the device and violate the related national regulations about telecom terminals. Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic waves, because signal reception may be affected. The device is not waterproof. Keep the device dry and store it in a shady and cool place. Do not use the device immediately after a sudden temperature change, because dew may be generated inside and outside the device. Do not use it until it becomes dry. Handle the device carefully. Do not drop, bend or strike it. Otherwise the device may be damaged. Only qualified personnel can dismantle and repair the device. The humidity between 5% and 95% is recommended. Do not connect the charger while using the device for a long period. Failing to do so will trigger the protection mechanism of the battery, and the battery will not be charged. If you want to charge the battery, please reconnect the charger. Do not connect the charger while using the device for a long period or use the device and battery in non-operating temperature. Failing to do so will shorten battery life or cause battery swelling or leakage. If the battery shows signs of swelling or leakage, please stop use immediately. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 18 Battery Safety WARNING!

The battery is not removable. Removal may cause fire or explosion. Using ZTE-unapproved or incompatible battery, charger or power adapter may damage your device, shorten its lifespan or cause a fire, explosion or other hazards. The recommended operating temperatures are 0 C to 35 C and the storage temperatures are -20 C to +45 C. Extreme temperatures can damage the device and reduce the charging capacity and lifespan of your device and battery. Do not change or replace the built-in rechargeable battery in your device by yourself. The battery can only be changed or replaced by ZTE or ZTE authorized service provider. Do not place the device or the battery in or near heating equipment, such as microwave ovens, stoves or radiators. Keep the device and the battery away from excessive heat and direct sunlight. If not, the device or the battery may overheat and cause explosion or fire. Do not disassemble, squeeze or puncture the device, as this can cause explosion or fire. Do not throw the device into a fire to avoid explosion. Please disconnect the charger when the battery is fully charged. Overcharging may shorten the battery life. When not using the device for a long period, please charge the battery about half and then store the device in a cool dry place. If the battery damages or shows signs of swelling or leakage, please stop use immediately and contact ZTE or ZTE authorized service provider for replacement. 19 Limited Warranty This warranty does not apply to defects or errors in the product caused by:

i. Reasonable abrasion. ii. End users failure to follow ZTEs installation, operation or maintenance instructions or procedures. iii. End users mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. iv. Modifications or repairs not provided by ZTE or a ZTE-

certified individual. v. Power failures, surges, fire, flood, accidents, and actions of third parties or other events outside ZTEs reasonable control. vi. Usage of third-party products or usage in conjunction with third-party products if such defects are due to the combined usage. vii. Any other cause beyond the range of normal usage intended for the product. End users have no right to reject or return the product, or receive a refund for the product from ZTE under the above-mentioned situations. This warranty is end users sole remedy and ZTEs sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law. Limitation of Liability ZTE shall not be liable for any loss of profits or indirect, special, 20 incidental or consequential damages resulting from or arising out of or in connection with using of this product, no matter whether or not ZTE had been advised, knew or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost. 21 LEGAL INFORMATION Copyright 2020 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.0 22 Troubleshooting Problem Recommended Action The Ensure that the Wi-Fi function is connection enabled. between your Refresh the network list and select device and a the correct SSID. client through Check the IP address, and ensure Wi-Fi cannot that your client can automatically be obtain an IP address. established. Enter the correct network key (Wi-

Fi password) when you connect the client to your device. 23 Troubleshooting Problem Recommended Action The client Ensure that your micro-SIM card is connected to available. the device Change the location and find a cannot place with good signal. access the Check the settings of the WAN Internet. connection mode. Contact your service provider and confirm your APN settings. The 4G Enter the correct address. The Mobile Hotspot default address http://192.168.0.1 is or configuration http://ufi.ztedevice.com. page cannot Use only one network adapter in be visited. your PC. Do not use any proxy server. 24 Getting More Help You can get help by:

Sending an email to mobile@zte.com.cn Visiting www.ztedevices.com 25 FCC Regulations:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. 26 Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage against the head with no separation, and near the body with the separation of 10 mm. Although the SAR is determined at the highest certified power level, the actual SAR level of the while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions 27 accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: SRQ-

MF971R. For this device, the highest reported SAR value for near the body is 1.09 W/kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. SAR compliance for body operation is based on a separation distance of 10 mm between the unit and the human body. Carry this device, at least 10 mm away from your body to ensure RF exposure level compliant or lower to the reported level. To support body operation, choose the belt clips or holsters, which do not contain metallic components, to maintain a separation of 10 mm between this and your body. 28

size:54*12mm 4-R1.0 PT CG 8C Model:MF971R Device Manager Website:http://192.168.0.1 Password FCC ID:SRQ-MF971R Made in China

ZTECorporation. Address: ZTE Plaza, Keji Road South,Hi-Tech, Industrial Park, Nanshan District,Shenzhen, P.R.China Tel: +86-21-68895397 Request of Confidentiality Federal Communications Commission Authorization and Evaluation Division Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant hereby requests confidential treatment of information accompanying of following product:

Product Name: LTE Ufi Product Model: MF971R FCC ID: SRQ-MF971R The following information should be held confidential:

All Schematics/block diagrams All Parts list for the above schematic diagram Tune-Up Procedure Operational description and technical overview of product Software Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. December 17, 2020 ZTECorporation. Address: ZTE Plaza, Keji Road South,Hi-Tech, Industrial Park, Nanshan District,Shenzhen, P.R.China Tel: +86-21-68895397

Date: 18 December 2020 ZTE Corporation Address: ZTE Plaza, Keji Road South,Hi-Tech, Industrial Park, Nanshan District,Shenzhen, P.R.China Tel: +86-21-68895397 PHOENIX TESTLAB GmbH Product Certification Knigswinkel 10 D 32825 Blomberg Subject: Declaration Operating Channel Limitation Product Name: LTE Ufi Product Model: MF971R FCC ID: SRQ-MF971R To Whom it may concern, The operating channels in 802.11 b/g/n mode for the device marketed to the US/Canada are firmware limited to channel 1 ~ 11 (2412 ~ 2462 MHz). The end-user has no possibility to select any other operating channels. If you have any questions, please feel free to contact me. Thank you. Sincerely, Certification Manager: Gong Yu ZTE Corporation Address: ZTE Plaza, Keji Road South,Hi-Tech, Industrial Park, Nanshan District,Shenzhen, P.R.China Tel: +86-21-68895397

UNII Declaration Letter We have declared below featured for FCC equipment authorization, device FCC ID: SRQ-MF286R

(1) DFS Device --

Master, Client without radar detection capability, Client with Radar detection capability , N/A

(2) Active / Passive Scanning , adhoc mode access point capability Frequency Band

(MHz) Active Scanning

(the device can transmit a probe passive scanning

(where the device Ad Hoc Mode capability Access point capability

(beacon)) can listen only 2412 2462 MHz 2422 2452 MHz 5745 5825 MHz 5755 5795 MHz 5180 5240 MHz 5190 5230 MHz 5260 5320 MHz 5270 5310 MHz 5500 5700 MHz 5510 5670 MHz Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, No No No No No No No No No No is with no probes) Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, No No No No No No No No No No Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, No No No No No No No No No No Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, No No No No No No No No No No

(3) Country code selection ability -

If no, pls explain how was implemented : use Microsoft network utility Yes , No

(4) Meet 15.202 requirement -

pls check below :

Yes , No , A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer. Apply , No Apply ,

(If apply , pls help to provide explanation on how it was implement (By hardware or software , and how software was controlled) Applicant: ZTE Corporation Address: ZTE Plaza, #55 Keji Road South, Hi-Tech, Industrial Park, Nanshan District,Guangdong Signature: December 232020 Name:Gong Yu Job Title: Certification Manager Ersteller:

Erstelldatum:

D. Brandhorst 20.06.2011 Revision:

Datum:

00 00.00.00 Seite 1 von 1

ZTECorporation. ZTE Plaza, Keji Road South,Hi-Tech, Industrial Park, Nanshan District,Shenzhen, P.R.China Tel: +86-21-68895397 AuthorizationLetter FCCID:SRQMF971RDate:December17,2020 Towhomitmayconcern:

We,theundersigned,herebyauthorizeTheStateRadio_monitoring_centerTestingCenter(SRTC)to actonourbehalf,asouragent,inthefollowingmattersrelatedtotheFCCapprovalofourproduct:

ProductName:LTEUfi ProductModel: MF971R FCCID: SRQMF971R Reportsubmittal,relatedcorrespondence,thesigningofalldocumentsrelatingtothesematters, andanyotherlawfulactivitynecessarytoobtainsuchcertification.AnyactcarriedoutbyTheState Radio_monitoring_centerTestingCenter(SRTC)withinthescopeofthisauthorizationshallhavethe sameeffectsasourown. Thisauthorizationshallexpire2monthsfromoriginaldate.Ifyouhaveanyquestionregardingthe authorization,pleasedonthesitatetocontactwithme. Thankyou. Sincerely, CertificationManager:GongYu ZTECorporation. Address: ZTE Plaza, Keji Road South,Hi-Tech, Industrial Park, Nanshan District,Shenzhen, P.R.China Tel: +86-21-68895397