FCC ID: SRQ-MF920V LTE Ufi

MF920V Quick Start Guide ZTE CORPORATION NO. 55, Hi-tech Road South, Shenzhen, P.R.China Postcode: 518057 1 Getting to Know Your Device Appearance The following figure is for your reference only. 1. *External antenna connectors (not all the devices support) 2. Charging/micro-USB jack 3. Indicator light 4. Power key Press and hold for about 3 seconds to power on/off your device. Press and hold for about 10 seconds to restart your device. 5. WPS key Press and hold for 3 seconds to activate the WPS function. 6. micro-SIM card slot and reset hole 2 Getting to Know Your Device Indicator lights Indicator Status Description Red solid /

blinking Green blinking Green solid Light off Blue solid Blue blinking Light off Blue solid Blue blinking Light off The battery is low. Please charge the battery. The battery is being charged. The battery level is middle or high. Your device is not being charged. Wi-Fi is active. WPS is active. Wi-Fi is off. You have unread messages. You have new messages. There is no unread message or new message. 3 Battery Wi-Fi SMS Red Network Green solid Green blinking Blue solid Blue blinking Error status. Not registered to the mobile network, no micro-SIM card inserted or no network service available. Registered to the 2G/3G mobile network. Connected to the 2G/3G mobile network and data is being transferred. Registered to the 4G LTE network. Connected to the 4G LTE network and data is being transferred. 4 Getting to Know Your Device Connection Scenarios The device allows multiple clients to surf on the Internet at the same time. The following figure is for your reference only. A micro-SIM card can be used to access the Internet. 5 Installing g Your Devic ce 1. Open the mi cro-SIM card cover. NOTE:

the cover rudely, bec cause it is connected d with the Do not remove device. 2. Install a micr WARNING Your device do other non-stan device, do not u ro-SIM card to the m

!

es not support SIM c dard micro-SIM card use those cards or a icro-SIM card slot. cards, nano-SIM card ds. To avoid damag ny card holders. ds or any ge to the 3. Close the m micro-SIM card cover r. 6 Device r other client devic vailable wireless netw abled client device ma or wireless networks our computer to obta es have works. anual for

. If you ain an IP

) of your device, a and click essary, and click OK. Getting to Know th e default Wi-Fi SS he Wi-Fi SID and connected to you r device e. ice with a USB cable perating system dete ects and talls the automatically inst Connect ting to Your Using Wi-F Fi our device. 1. Power on yo t your computer or 2. Ensure that Fi, and search for av enabled Wi-

NOTE: Re fer to your Wi-Fi-ena further details on how to search fo use a compute er, you need to set yo address autom atically. Wi-Fi name (SSID) 3. Select the Connect. i-Fi password if nece fer to the chapter G assword to get th 4. Enter the Wi NOTE: Ref SSID and Pa password. 5. Wait until t he client device is successfully

. SB Cable Using a US omputer to your devi 1. Connect a co 2. Power on y your device. The op ew hardware, and identifies ne software. 7 NOTE:

If the system d oes not automatically double-click th he device installation install the softw ware. the computer 3. Wait until successfully

. is y launch installation, n icon in My Com you can puter to connected to your r device Getting t Passwor to Know the rd e Wi-Fi SSID D and You can view SSID and pass the label on the dev sword. vice to get the defa ult Wi-Fi Logging Hotspot in to th he 4G M Configurati on Page obile the connection be tween your device and the 1. Ensure that client device 2. Launch the http://ufi.zte 3. Enter the p configuration NOTE: The e is correct. Internet browser and edevice.com in the a password to log in n page. e default password is 8 d enter http://192.16 address bar. to the 4G Mobile 68.0.1 or Hotspot s admin. Changing Password the Wi-Fi SSID or 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Wi-Fi Settings. 3. Change the Network Name (SSID) or the Password in the Main SSID area. 4. Click Apply. Accessing the Internet After a client device is successfully connected to your device, you can access the Internet in Automatic or Manual mode. The default mode is Automatic. Operation Mode Automatic Your device is automatically connected to the Internet, and you can surf on the Internet through the client. Manual 1. Log in to the 4G Mobile Hotspot configuration page. 2. In My router section, select LTE (or other network type) Settings > Connection Mode > Manual, and then click Apply. 9 3. Click to return to the home page, and then click or

. NOTE:

To change current connection setting, please disconnect from network. To modify the parameters of your device, log in to the 4G Mobile Hotspot configuration page. Configuring Your PC The following procedure describes how to configure the Internet Protocol in Windows 7 for your Wi-Fi connection. 1. Right-click Network and select Properties. 2. Select Change adapter settings. 3. Right-click Wireless Network Connection and select Properties. 4. Select Internet Protocol Version 4 (TCP/IPv4), and click Properties. 5. Select Obtain an IP address automatically and Obtain DNS server address automatically, and click OK. 10 the device Warning and Notice To the Users If inadequately shielded, some electronic devices, for example, the electronic system of vehicles, may be affected by the electromagnetic interference caused by the device. Consult the manufacturers of such devices before using if necessary. Operating the device may interfere with medical instruments such as hearing aids and pacemakers. Always keep the device more than 20 centimeters away from such medical instruments when your device is powered on. Power off the device if necessary. Consult a physician or the manufacturers of medical instruments before using the device if necessary. Be aware of the usage limitation when using the device at places such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Power off the device if necessary. Do not use electronic transmission devices in aircrafts, at petrol stations or in hospitals. Observe and obey all warning signs, and power off the device in these conditions. Do not touch the inner antenna area unless necessary. Otherwise the performance of the device may be affected. Do not use the device in an enclosed environment or where heat dissipation is poor. Prolonged work in such space may cause excessive heat and raise ambient temperature, which may lead to automatic shutdown of the device for your safety. In the case of such event, cool the device in a well-ventilated place before turning on for normal use. Keep the device out of the reach of small children. The device may cause an injury if used as a toy. 11 When the device is operating, do not touch the metallic parts. Failing to do so may cause burns. Use original accessories or accessories that are authorized. Using any unauthorized accessories may affect the performance of the device and violate the related national regulations about telecom terminals. Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic waves, because signal reception may be affected. The device is not waterproof. Keep the device dry and store it in a shady and cool place. Do not use the device immediately after a sudden temperature change, because dew may be generated inside and outside the device. Do not use it until it becomes dry. Handle the device carefully. Do not drop, bend or strike it. Otherwise the device may be damaged. Only qualified personnel can dismantle and repair the device. An operating temperature between -10C and +60C and humidity between 5% and 95% are recommended. Using Battery Do not change the built-in rechargeable battery in your device by yourself. The battery can only be changed by ZTE or ZTE authorized service provider. Limited Warranty This warranty does not apply to defects or errors in the product caused by:

i. Reasonable abrasion. ii. End users failure to follow ZTEs installation, operation or maintenance instructions or procedures. 12 iii. End users mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. iv. Modifications or repairs not provided by ZTE or a ZTE-certified individual. v. Power failures, surges, fire, flood, accidents, and actions of third parties or other events outside ZTEs reasonable control. vi. Usage of third-party products or usage in conjunction with third-party products if such defects are due to the combined usage. vii. Any other cause beyond the range of normal usage intended for the product. End users have no right to reject or return the product, or receive a refund for the product from ZTE under the above-mentioned situations. This warranty is end users sole remedy and ZTEs sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law. Limitation of Liability ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, no matter whether or not ZTE had been advised, knew or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost. 13 LEGAL INFORMATION Copyright 2016 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.0 Edition Time: April 12, 2016 14 Troubleshooting Problem The connection between your device and a PC through a cable USB cannot be established. The connection between your device and a client through Wi-Fi cannot be established. Recommended Action Install the software, and run the installation program in the path of My Computer. If is abnormal, reinstall the software. You need to uninstall the software first. the driver of your device Ensure that the Wi-Fi function is enabled. Refresh the network list and select the correct SSID. Check the IP address, and ensure that your client can automatically obtain an IP address. Enter the correct network key (Wi-Fi password) when you connect the client to your device. 15 shooting Troubles Check ed Action at your micro-SIM c Recommende Ensure th available. he location and find a Change th signal. with good e settings of th connection n mode. Contact y your service provide confirm yo our APN settings. the e correct address ddress is http://192.1 default ad fi.ztedevice.com. or http://uf Use only one network adap Enter the your PC. Do not use e any proxy server. card is a place WAN er and

. The 68.0.1 pter in Problem clien nt The t to connected ce the devic cannot acces ss the Internet. 4G G The Mobile Hotspot configuration page canno ot be visited. Getting M More Help You can get he Sending a Visiting w Calling th elp by:

an email to mobile@

www.ztedevice.com he service hotline: +8 16

@zte.com.cn 86-755-26779999 FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device was set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body with the separation of 10 mm. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless devices employing a unit of measurement is known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. This device is complied with SAR in ANSI/IEEE C95.1-1992 and had been tested in accordance with the measurement methods and procedures specified in IEEE1528. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. For this device, the highest reported SAR value for usage near the body is 1.441 W/kg. While there may be differences between the SAR levels of various positions, they all meet the government requirements. SAR compliance for body-worn operation is based on a separation for general population

/uncontrolled exposure limits 17 distance of 10 mm between the unit and the human body. Carry this device at least 10 mm away from your body to ensure RF exposure level compliant or lower to the reported level. To support bodyworn operation, choose the belt clips or holsters, which do not contain metallic components, to maintain a separation of 10 mm between this device and your body. RF exposure compliance with any body-worn accessory, which contains metal, was not tested and certified, and use such body-worn accessory should be avoided. FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference is no guarantee that interference will not occur in a particular installation. If to radio communications. However, there 18 this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 19