Z6200MEX LTE OBDII Hotspot User Manual

Z6200MEX Quick Start Guide ZTE CORPORATION NO. 55, Hi-tech Road South, Shenzhen, P.R.China Postcode: 518057 Getting to Know Your OBD2 Device Appearance The following figure is for your reference only. 1 2 3 6 4 5 1. Reset hole 2. micro-SIM card slot 3. Restart key 4. LED 1 5. LED 2 6. OBD interface 1 2 Getting to Know Your OBD2 Device Indicator lights Installing the micro-SIM card 1. Use the tray eject tool to take out the card tray. 2. Put the micro-SIM card into the card tray and slip it into the Indicator Status Description card slot. WARNING!

Green blinking Powered by the internal battery. Green solid Red solid Green solid Powered by the vehicle battery. Turn on but not register. Registered to the 4G network. Green blinking Connected to the 4G LTE network and data is being transferred. LED 1(Power) LED 2(Signal) NOTE:

The charging temperature should be lower than 60. To avoid damage to the phone, please do not use other kinds of SIM cards, and do not use a non-standard micro-SIM card cut from a SIM card. You can get the standard micro-SIM card from your service provider. 3. Close the micro-SIM card cover. Installing Your OBD2 Device 1. Make sure your vehicle is parked outside in a safe location and the engine is turned off. 2. Find your Vehicles On-Board Diagnostics (OBD II) connector port. NOTES:

The OBD II port is usually located under the drivers dash side of your car, often within 18 inches of the steering wheel (as 1 to 8 shown in the following picture). 3 4 Connecting to Your OBD2 Device Turning on Your OBD2 Device Start your vehicles engine and let it run for at least 30 seconds. Using Your Wi-Fi Devices 1. Find your OBD2 device's network name in your Wi-Fi device's list of available wireless networks. 2. Select the Wi-Fi name (SSID) of your OBD2 device. 3. Input the password, and then tap Connect. 6

If youre having trouble locating your cars OBD II port, reference your vehicles manual. 3. Insert your Device into the vehicles OBD II port. 5 NOTE: Refer to the chapter Getting to Know the Wi-Fi SSID and Password to get the default Wi-Fi SSID and password. Getting to Know the Wi-Fi SSID and Password You can view the label on the device to get the default Wi-Fi SSID and password. in to the 4G Mobile Logging Hotspot Configuration Page Use 4G Mobile Hotspot configuration on your Wi-Fi device to manage settings. Changing Password the Wi-Fi SSID and 1. From the connected device, log in to the 4G Mobile Hotspot configuration page. 2. Select Settings > Wi-Fi Settings. 3. Change the Network Name (SSID) and Password. 4. Click Apply. Setting up Allowed Devices Enable Allowed Devices to prevent other device from connecting to the OBD2 device, only the MAC address listed in the Allowed Devices Information section can access your OBD2 device. 1. Ensure that the connection between your OBD2 device and the Wi-Fi device is correct. 2. Launch the Internet browser and enter http://192.168.0.1 in the address bar. 3. Enter the username and password to log in to the 4G Mobile Hotspot configuration page. NOTE: The default password is admin. 7 8 1. From the connected device, log in to the 4G Mobile Hotspot configuration page. 2. Select Settings > Wi-Fi Settings. 3. Set Allowed Devices Switch to On, and click Apply. 4. Enter the Nickname and MAC Address. 5. Click Apply. NOTE: To prevent a device from reconnecting to your NOTE:

WAN Connection Mode > Manual, and then click Apply. 4. Select Home and click to connect to the Internet. OBD2 device, click Remove next to the device. Accessing the Internet After a client device is successfully connected to your device, you can access the Internet in Automatic or Manual mode. The default mode is Automatic. Operation Mode Automatic Your OBD2 device is automatically connected to the Internet, and you can surf on the Internet through the Wi-Fi device. Manual 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Home and click to disconnect from the Internet. 3. Select Settings > Network Settings >

To modify the parameters of your device, log in to the 4G Mobile Hotspot configuration page. 9 10 LEGAL INFORMATION Copyright 2016 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.0 Edition Time: July 1, 2016 Manual No.:

11 Getting More Help You can get help by:

Sending an email to mobile@zte.com.cn Visiting www.ztewelink.com 12