FCC ID: SRQ-Z6200MEX LTE OBDII Hotspot

Z6200MEX Quick Start Guide ZTE CORPORATION NO. 55, Hi-tech Road South, Shenzhen, P.R.China Postcode: 518057 Getting to Know Your OBD2 Device Appearance The following figure is for your reference only. 1 2 3 6 4 5 1. Reset hole 2. micro-SIM card slot 3. Restart key 4. LED 1 5. LED 2 6. OBD interface 1 2 Getting to Know Your OBD2 Device Indicator lights Installing the micro-SIM card 1. Use the tray eject tool to take out the card tray. 2. Put the micro-SIM card into the card tray and slip it into the Indicator Status Description card slot. WARNING!

Green blinking Powered by the internal battery. Green solid Red solid Green solid Powered by the vehicle battery. Turn on but not register. Registered to the 4G network. Green blinking Connected to the 4G LTE network and data is being transferred. LED 1(Power) LED 2(Signal) NOTE:

The charging temperature should be lower than 60. To avoid damage to the phone, please do not use other kinds of SIM cards, and do not use a non-standard micro-SIM card cut from a SIM card. You can get the standard micro-SIM card from your service provider. 3. Close the micro-SIM card cover. Installing Your OBD2 Device 1. Make sure your vehicle is parked outside in a safe location and the engine is turned off. 2. Find your Vehicles On-Board Diagnostics (OBD II) connector port. NOTES:

The OBD II port is usually located under the drivers dash side of your car, often within 18 inches of the steering wheel (as 1 to 8 shown in the following picture). 3 4 Connecting to Your OBD2 Device Turning on Your OBD2 Device Start your vehicles engine and let it run for at least 30 seconds. Using Your Wi-Fi Devices 1. Find your OBD2 device's network name in your Wi-Fi device's list of available wireless networks. 2. Select the Wi-Fi name (SSID) of your OBD2 device. 3. Input the password, and then tap Connect. 6

If youre having trouble locating your cars OBD II port, reference your vehicles manual. 3. Insert your Device into the vehicles OBD II port. 5 NOTE: Refer to the chapter Getting to Know the Wi-Fi SSID and Password to get the default Wi-Fi SSID and password. Getting to Know the Wi-Fi SSID and Password You can view the label on the device to get the default Wi-Fi SSID and password. in to the 4G Mobile Logging Hotspot Configuration Page Use 4G Mobile Hotspot configuration on your Wi-Fi device to manage settings. Changing Password the Wi-Fi SSID and 1. From the connected device, log in to the 4G Mobile Hotspot configuration page. 2. Select Settings > Wi-Fi Settings. 3. Change the Network Name (SSID) and Password. 4. Click Apply. Setting up Allowed Devices Enable Allowed Devices to prevent other device from connecting to the OBD2 device, only the MAC address listed in the Allowed Devices Information section can access your OBD2 device. 1. Ensure that the connection between your OBD2 device and the Wi-Fi device is correct. 2. Launch the Internet browser and enter http://192.168.0.1 in the address bar. 3. Enter the username and password to log in to the 4G Mobile Hotspot configuration page. NOTE: The default password is admin. 7 8 1. From the connected device, log in to the 4G Mobile Hotspot configuration page. 2. Select Settings > Wi-Fi Settings. 3. Set Allowed Devices Switch to On, and click Apply. 4. Enter the Nickname and MAC Address. 5. Click Apply. NOTE: To prevent a device from reconnecting to your NOTE:

WAN Connection Mode > Manual, and then click Apply. 4. Select Home and click to connect to the Internet. OBD2 device, click Remove next to the device. Accessing the Internet After a client device is successfully connected to your device, you can access the Internet in Automatic or Manual mode. The default mode is Automatic. Operation Mode Automatic Your OBD2 device is automatically connected to the Internet, and you can surf on the Internet through the Wi-Fi device. Manual 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Home and click to disconnect from the Internet. 3. Select Settings > Network Settings >

To modify the parameters of your device, log in to the 4G Mobile Hotspot configuration page. 9 10 LEGAL INFORMATION Copyright 2016 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.0 Edition Time: July 1, 2016 Manual No.:

11 Getting More Help You can get help by:

Sending an email to mobile@zte.com.cn Visiting www.ztewelink.com 12

LEGAL INFORMATION Copyright 2016 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Z6200MEX Product Safety and Warranty Information 1 2 LEGAL INFORMATION .................................................................... 2 Regulatory and Safety Information Regulatory and Safety Information ................................................ 4 To the Owner ....................................................................... 4 To the Users ........................................................................ 4 Radio Frequency (RF) Energy ............................................. 5 FCC Compliance ................................................................. 6 Warranty .......................................................................................... 9 Consumer Limited Warranty ................................................ 9 To the Owner Operating the device may interfere with medical instruments such as hearing aids and pacemakers. Always keep the device more than 10 mm away from such medical instruments when your device is powered on. Power off the device if necessary. Consult a physician or the manufacturers of medical instruments before using the device if necessary. Be aware of the usage limitation when using the device at places such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Power off the device if necessary. Do not use electronic transmission devices in aircrafts, at petrol stations or in hospitals. Observe and obey all warning signs, and power off the device in these conditions. Keep the device out of the reach of small children. The device may cause an injury if used as a toy. When the device is operating, do not touch the metallic parts. Failing to do so may cause burns. To the Users Use original accessories or accessories that are authorized. Using any unauthorized accessories may affect the performance of the device and violate the related national regulations about telecom terminals. Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic waves, because signal reception may be affected. The device is not waterproof. Keep the device dry and store it in a 3 4 shady and cool place. Do not use the device immediately after a sudden temperature change, because dew may be generated inside and outside the device. Do not use it until it becomes dry. Handle the device carefully. Do not drop, bend or strike it. Otherwise the device may be damaged. Only qualified personnel can dismantle and repair the device. An operating temperature between -4F ~ 158F (-20C and +70C) and humidity between 5% and 95% are recommended. Do not insert or remove the device from the OBD II port at gas stations or places where there are explosive gases or explosive products being processed. Radio Frequency (RF) Energy This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. FCC ID: SRQ-Z6200CA 5 FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 6 en conjonction avec une autre antenne ou un autre metteur, exception faites des radios intgres qui ont t testes. The County Code Selection feature is disabled for products marketed in the US/ Canada. La fonction de slection de l'indicatif du pays est dsactive pour les produits commercialiss aux tats-Unis et au Canada. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 10mm between the radiator & your body. Dclaration d'exposition aux radiations: Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 10 mm de distance entre la source de rayonnement et votre corps. IC: 5200A-Z6200CA Consult the dealer or an experienced radio/TV technician for help. Note: The country code selection is for non-U.S. models only and is not available to all U.S. models. Per FCC regulation, all Wi-Fi products marketed in the U.S. must be fixed to U.S. operation channels only. Industry Canada statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: 1) l'appareil ne doit pas produire de brouillage, et 2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios. Cet appareil et son antenne ne doivent pas tre situs ou fonctionner 7 8 Warranty Consumer Limited Warranty ZTE (Seller) offers you a limited warranty that the enclosed product or products (the Product) will be free from defects in material and workmanship for a period that expires one year from the date of sale of the Product to you, provided that you are the original end-user purchaser of the Product and provided that your purchase was made from a supplier authorized by the Seller. Transfer or resale of a Product will automatically terminate warranty coverage with respect to that Product. This limited warranty is not transferable to any third party, including but not limited to any subsequent purchaser or owner of the Product. This limited warranty is applicable to end users in the United States and Puerto Rico. Seller will, at its sole and absolute discretion, either repair or replace a Product (which unit may use refurbished parts of similar quality and functionality) if found by Seller to be defective in material or workmanship, or if Seller determines that it is unable to repair or replace such Product, Seller will refund the purchase price for such Product, provided that the subject Product (i) is returned to a Seller authorized service center within the one year warranty period, and (ii) is accompanied by a proof of purchase in the form of a bill of sale or receipted invoice which evidences that the subject Product is within the one year warranty period. After the one year warranty period, you must pay all shipping, parts and labor charges. In the event that the product is deemed unrepairable or has been removed from the list of products supported by the Seller, you will only be liable for shipping and labor charges. This limited warranty does not cover and is void with respect to the following: (i) any Product which has been improperly installed, repaired, maintained or modified; (ii) any Product which has been subjected to misuse (including any Product used in conjunction with hardware electrically or mechanically incompatible or used with accessories not approved by Seller), abuse, accident, physical damage, abnormal operation, improper handling, neglect, exposure to fire or liquid; (iii) any Product operated outside published maximum ratings; (iv) cosmetic damage; (v) any Product on which warranty stickers or Product serial numbers have been removed, altered, or rendered illegible; (vi) cost of installation, removal or reinstallation; (vii) signal reception problems (unless caused by defects in material and workmanship); (viii) damage the result of fire, flood, acts of God or other acts which are not the fault of Seller and which the Product is not specified to tolerate, including damage caused by mishandling, shipping and blown fuses; (ix) consumables (such as fuses); or (x) any Product which has been opened, repaired, modified or altered by anyone other than Seller or a Seller authorized service center. USE ONLY SELLER APPROVED ACCESSORIES WITH SELLER DEVICES. USE OF ANY UNAUTHORIZED ACCESSORIES MAY BE DANGEROUS AND WILL INVALIDATE THE DEVICE WARRANTY IF SAID ACCESSORIES CAUSE DAMAGE OR A DEFECT TO THE DEVICE. SELLER SPECIFICALLY DISCLAIMS LIABILITY FOR ANY 9 10 ZTE; Mobley; ZTE Mobley; ZTE VM6200; ZTE Mobley VM6200; ZTE Mobley Product Safety and Warranty Information; ZTE Mobley VM6200 Product Safety and Warranty Information; ZTE Mobley Product Safety; ZTE Mobley Warranty Information; ZTE Mobley Product Safety;{AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, PUNITIVE, EXEMPLARY, AGGRAVATED, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, WHETHER FORESEEABLE OR UNFORESEEABLE OF ANY KIND WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOSS OF PROFITS, UNANTICIPATED BENEFITS OR REVENUE, ANTICIPATED PROFITS ARISING OUT OF USE OF OR INABILITY TO USE ANY PRODUCT (FOR EXAMPLE, WASTED AIRTIME CHARGES DUE TO THE MALFUNCTION OF A PRODUCT) OR CONTRIBUTION OR INDEMNITY IN RESPECT OF ANY CLAIM RELATED TO A PRODUCT. REPAIR OR REPLACEMENT OF A DEFECTIVE PRODUCT OR REFUND OF THE PURCHASE PRICE RELATING TO A DEFECTIVE PRODUCT, AS PROVIDED UNDER THIS WARRANTY, ARE YOUR SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF THE LIMITED WARRANTY, AND SUBJECT TO THIS WARRANTY, THE PRODUCTS ARE APPROVED AND ACCEPTED BY YOU AS IS. SELLER MAKES NO OTHER WARRANTIES, REPRESENTATIONS OR CONDITIONS OF ANY KIND, ORAL OR WRITTEN, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, WITH RESPECT TO THE PRODUCTS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OR CONDITION OF 11 MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR AGAINST INFRINGEMENT OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF TRADE USAGE OR OUT OF A COURSE OF DEALING OR COURSE OF PERFORMANCE. NO DEALER, DISTRIBUTOR, AGENT OR EMPLOYEE IS AUTHORIZED TO MAKE ANY MODIFICATION OR ADDITION TO THIS WARRANTY. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. For warranty service information, please call the following telephone number: 1-800-617-5065. IMPORTANT: Please provide warranty information (proof of purchase) to ZTE in order to receive warranty service at no charge. If the warranty has expired on the device, charges may apply. 12

Reference No.: 170926W004 PHOTOGRAPHS OF THE EUT BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 1 of 13 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 2 of 13 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 3 of 13 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 4 of 13 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 5 of 13 Report Version 1 Reference No.: 170926W004 WWAN Antenna BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 6 of 13 Report Version 1 Reference No.: 170926W004 WLAN Antenna BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 7 of 13 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 8 of 13 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 9 of 13 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 10 of 13 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 11 of 13 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 12 of 13 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology (Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 13 of 13 Report Version 1

Reference No.: 170926W004 PHOTOGRAPHS OF THE EUT BV 7Layers Communications Technology

(Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 1 of 4 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology

(Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 2 of 4 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology

(Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 3 of 4 Report Version 1 Reference No.: 170926W004 BV 7Layers Communications Technology

(Shenzhen) Co. Ltd No.B102, Dazu Chuangxin Mansion, North of Beihuan Avenue, North Area, Hi-Tech Industrial Park, Nanshan District, Shenzhen, Guangdong, China Tel: +86 755 8869 6566 Fax: +86 755 8869 6577 Email: customerservice.dg@cn.bureauveritas.com Page 4 of 4 Report Version 1

VM6200S-U AM SKU: XXXXXXXXXXXX Device label 34.1mm Marca: ZTE Modelo: Z6200MEX Escner Automotriz OBD-II IMEI: XXXXXXXXXXXXXXX S/N: XXXXXXXXX m m 5 3 3

. WIFI MAC: XXXXXXXXX FCC ID: SRQ-Z6200MEX SSID: XXXXXXXXXX Password: XXXXXXXX ALIMENTACION: 9-16 Vcc DATE: MM/YYYY HECHO EN CHINA Size: 34.1*33.5*0.15mm, 3-R0.5 Material code: 5646125300MT Product box label IMPORTADOR:

ZTE CORPORATION DE MEXICO,S DE R.L. DE C.V. LAGO ZURICH NO.245,TORRE FRISCO, PISO 1 COL.AMPLIACION GRANADA, DEL.MIGUEL HIDALGO C.P.11520,CIUDAD DE MEXICO R.F.C.ZCM-030408-7QA HECHO EN CHINA FCC ID: XXXXXXXX ALIMENTACION: 9-16 Vcc Escner Automotriz OBD-II MARCA: ZTE MODELO: Z6200MEX COLOR: NEGRO Incluye:

Escner automotriz Gua de inicio rpido CERTIFICADO IFT:

EN TRAMITE 35mm IMEI: XXXXXXXXXXXXXXX Le sugerimos leer la gua de inicio rpido anexa antes de utilizar su equipo. NUMERO DE SERIE:

XXXXXXXXXXXXXXX 75mm Size: 75*35mm Material code: 5646148900MT Master carton label MASTER BOX NO.:

CODE:

XXXXXXXXXXXX XXXXXXXXXXXX Model: Z6200MEX Weight: XXXX g Colour: XXXXX Version:

Quantity: XX Accessory:

Category: OBD Box Status: Full HECHO EN CHINA XXXXXXXXXXXXXXX XXXXXXXXXXXXXXX 101.6mm XXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXX Q/A REQ NO.:XXXXXXXXXXXXX Q/A Date:

Size: 127*101.6mm(5*4) Material code: 078761000283 127mm Pallet label Pallet Number: 66000001 SKU: XXXXXXXXXXXX QTY: XXXX PO: XXXXX YYYY/DD/MM :D.S.R.C Made in China

* fo * :tellaP Size: 127*101.6mm(5*4) Material code: 078761000283 127mm 101.6mm

Tel: 408-526-1188 Fax: 408-526-1088 Email: TCB@siemic.com 775 Montague Expressway Milpitas, CA 95035 Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Initial Release (obsolete) Revised wording (obsolete) Updated company template (obsolete) Updated letter information (obsolete) Added FCC ID field (current) Revision History From To 1.0 1.0 2.0 1.0 3.0 2.0 3.0 4.0 5.0 4.0 Approved Date Nov-14-2006 Sept25-2007 Jan-31-2012 May-23-2014 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 October 13, 2017 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, ZTE Corporation, hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s):

(LTE OBDII Hotspot, Z6200MEX) FCC ID: SRQ-Z6200MEX Sincerely, _______________________ Amyee Qian / Certification Engineer Bureau Veritas 7Layers Communications Technology (Shenzhen) Co. Ltd Tel: +86 755 8869 6566 #1545 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0

Date: October 13, 2017 ZTE Corporation ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China Federal Communications Commission 7435 Oakland Mills Road - Gate A Columbia, Maryland 21046 Schematic Diagram Block Diagram Parts List Tune-up Procedure Operational Description Subject: Request for Confidentiality FCC ID: SRQ-Z6200MEX To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after the Grant Date of Equipment Authorizations. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Min Zhang / Certification Manager ZTE Corporation Tel: +86-21-68897541 Fax: +86-21-50801070 E-mail: zhang.min13@zte.com.cn External Photos Internal Photos Test Setup Photos Users Manual

ZTE Corporation ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong, P.R.China Power of Attorney Date: October 13, 2017 To whom it may concern, Please be notified that I, Min Zhang, have designated Amyee Qian of Bureau Veritas 7Layers Communications Technology (Shenzhen) Co. Ltd as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Amyee Qian of Bureau Veritas 7Layers Communications Technology

(Shenzhen) Co. Ltd on the matters relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. As defined in 47 CFR Ch. 1.U.S.C. 862, we further certify that neither the applicant nor any party to this application is subject to a denial to Federal benefits, including FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act. This authorization is limited to the product of as following:

FCC ID: SRQ-Z6200MEX If you have any acknowledgement and response, please send it to Amyee Qian of Bureau Veritas 7Layers Communications Technology (Shenzhen) Co. Ltd directly. Should you have any question or comment regarding this matter, please have my best attention. Sincerely yours, Min Zhang / Certification Manager ZTE Corporation Tel: +86-21-68897541 Fax: +86-21-50801070 E-mail: zhang.min13@zte.com.cn