FCC ID: SRQ-T3000 WiFi6 Router

T3000 Lets go Getting started with your device. 1 1. Connect Your Device Connect the WAN/LAN4 port to the broadband service network port with a network cable. 2 2. Power on Your Device Connect the original power adapter to your device and then your device will be powered on and connect to the Internet automatically. 3 3. Access the Internet Wi-Fi: Get the default SSID and password on the label and connect to the Wi-Fi network with your mobile device, and then access the Internet. 4 Network cable(RJ45): Connect with the computer via LAN ports and then access the Internet. 5 Manage Your Device You can manage the device by logging in to the configuration web page. 1. View the label on your device to get the default Device Manager Website IP address and Password. 2. Launch the Internet browser and enter the Device Manager Website IP address in the address bar. Input the password and then click Login. 3. 4. After the configuration web page is opened, you can change the Wi-Fi SSID, password or other settings. 6 Mesh Network Function Your device has the Wi-Fi Mesh ability. You can create Wi-Fi Mesh network to form a larger range of Wi-Fi network in your house and ensure seamless Wi-Fi roaming when you move. 7 To set your mesh network:

1. Log in to the management web page. 2. Click Mesh Network icon

. 3. 4. Follow the instructions to create your mesh network. Enjoy your mesh network. 8 Indicator Lights and Interfaces 9 1 LAN ports Connect to a PC. 2 WAN/LAN WAN/LAN4: Connect to a WAN in the single WAN mode. ports WAN/LAN3: If you want to use two WAN connections, you need to switch to the Multi WAN mode on the management web page and then connect the other WAN to the WAN/LAN3 port. 3 Power port Connect to the original power adapter. 4 WPS key Press and hold for about 2 seconds to activate the WPS function or create the mesh network. 5 NFC area When you bring your NFC-enabled phone and the device together, follow the instructions on your phone to connect to the Wi-Fi network without entering the password. 6 Indicator Red blinking:

The device is being started. The device is being restored to the factory settings. Red on: The WAN is not connected. White blinking:

WPS is activating. The mesh network is being created. White on: The WAN is connected. Off: The power adapter is not connected. 7 RESET Press and hold for about 3 seconds to restore your device to the factory settings. 10 Troubleshooting Internet Related Problems Symptoms Possible Problems / Solutions I cannot access the Internet at all. Please check your configuration settings. Please wait 1~ 2 minutes for the device to initialize. Check your network indicators. I cannot visit the management web Enter the correct IP address. You can view the label page. I cannot establish the Wi-Fi connection between my device and the client. on your device to get the default IP address. Only use one network adapter in your PC. Do not use any proxy server. Disable the automatic switch to the mobile network on your phone. Make sure the Wi-Fi function is active. Refresh network list and select the correct SSID. Check the IP address to make sure your client can obtain an IP address automatically in the Internet protocol (TCP/IP) properties. Type the correct network key (Wi-Fi password) when you connect to the device. 11 Others Symptoms Possible Problems / Solutions Problems with the passwords. I cannot create the mesh network. View the label to get the default passwords. If you have changed the passwords and forgotten them, you need to restore the device to the factory default settings. Refer to the operation steps on the web page. Restore the device to the factory settings and try again. 12 Getting More Help You can get help by:

Sending an email to mobile@zte.com.cn Visiting https://www.ztedevices.com 13 LEGAL INFORMATION Copyright 2022 ZTE CORPORATION. All rights reserved. No part of this publication may be quoted, reproduced, translated or used in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. Notice ZTE Corporation reserves the right to make modifications on print errors or update specifications in this guide without prior notice. Disclaimer Images and screenshots used in this guide may differ from the actual product. Content in this guide may differ from the actual product or software. Trademarks ZTE and the ZTE logos are trademarks of ZTE Corporation. Other trademarks and trade names are those of their respective owners. Version No.: R1.0 14 Warning and Notice Safety Precautions Some electronic devices may be susceptible to electromagnetic interference. Locate the device away from TV set, radio and other electronic equipment to avoid electromagnetic interference. The device may interfere with medical devices like hearing aids and pacemakers. Consult a physician or the manufacturer of the medical device before using it. Please keep yourself at least 20 centimeters away from your device. Do not use your device in dangerous environments such as oil terminals or chemical factories where there are explosive gases or explosive products being processed. Please use original accessories or accessories that are authorized by ZTE. Unauthorized accessories may affect the device performance, damage the device or cause danger to you. Do not attempt to dismantle the device. There are no user-serviceable parts. Do not allow the device or accessories to come into contact with liquid or moisture at any time. Do not immerse the device in any liquid. Do not place objects on top of the device. This may lead to overheating of the device. The device must be placed in a well-ventilated environment for use. Do not expose the device to direct sunlight or store it in hot areas. High temperature can shorten the life of electronic devices. Do not allow children to play with the device or power adapter. The device is for indoor use only. Do not use the device outside. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. Cleaning and Maintaining Use an antistatic cloth to clean the device. Do not use chemical or abrasive cleanser as these could damage the plastic case. Turn off your device before you clean it. 15 Use the device within the temperature range of -20 ~ +55 , and the storage temperature range is

-40 ~ +70. The humidity range is 5%~95%. Do not use your device during a thunderstorm. Remove the mains power pack from the wall socket. Limited Warranty This warranty does not apply to defects or errors in the product caused by:

i. Reasonable abrasion. ii. End users failure to follow ZTEs installation, operation or maintenance instructions or procedures. iii. End users mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. iv. Modifications or repairs not provided by ZTE or a ZTE-certified individual. v. Power failures, surges, fire, flood, accidents, and actions of third parties or other events outside ZTEs reasonable control. vi. Usage of third-party products or usage in conjunction with third-party products if such defects are due to the combined usage. vii. Any other cause beyond the range of normal usage intended for the product. End users have no right to reject or return the product, or receive a refund for the product from ZTE under the above-mentioned situations. This warranty is end users sole remedy and ZTEs sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law. Limitation of Liability ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, no matter whether or not ZTE had been advised, knew or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost. 16 FCC Regulations:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. 17 Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Radio Frequency (RF) Exposure Your device contains a transmitter and a receiver. When it is ON, it receives and transmits RF energy. When you communicate with your device, the system handling your connection controls the power level at which your device transmits. Important safety information regarding radiofrequency radiation (RF) exposure. To ensure compliance with RF exposure guidelines the device must be used with a separation from the body. Failure to observe these instructions could result in your RF exposure exceeding the relevant guideline limits. The transmitter is using external antenna that operate at 20cm or more from nearby persons. The FCC grant can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID: SRQ-T3000 18 IC Notice This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Immediately following the above notice, the manufacturer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permission antenna gain (in dBi) and required impedance for each. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. IC: 5200E-T3000 19 IC Radiation Exposure Statement This device complies with IC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the IC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR-102 definies pour unenvironnement non controle Afin d'eviter la possibilite de depasser les limites d'exposition auxfrequences radio de la CNR-102, la proximite humaine a l'antenne ne doit pas etre inferieure a 20 cm (8 pouces) pendant le fonctionnement norma. 20 ZTE CORPORATION NO. 55, Hi-tech Road South, Shenzhen, P.R.China Postcode: 518057 21

back of the device Model:T3000 Mac:

SIN:

Wari SSID:

Wi key:

Device Manager Website:

Password. MADE IN CHINA. et ZTELink cee

ZTE Corporation Request for Confidentiality Date:

_2022-3-10_ Subject: Confidentiality Request for: _____ FCC ID: SRQ-T3000 ____ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Permanent Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term ______(Insert Explanation as Necessary)______ Permanent*1 Permanent Permanent Permanent Permanent Permanent*

Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual

*Note:

______ ZTE Corporation _____ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __180_ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TCB in the event information regarding the product or the product is made available to the public. TCB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By:

(Signature/Title2) Chaijue Ding

(Print name)

ZTE Corporation UNII Declaration Letter We have declared below featured for FCC equipment authorization, device FCC ID: SRQ-T3000

(1) DFS Device --

Master, Client without radar detection capability, Client with Radar detection capability , N/A

(2) Active / Passive Scanning , adhoc mode access point capability Frequency Band

(MHz) Active Scanning

(the device can transmit a probe

(beacon)) 2412 2462 MHz 2422 2452 MHz 5745 5825 MHz 5755 5795 MHz 5180 5240 MHz 5190 5230 MHz 5260 5320 MHz 5270 5310 MHz 5500 5700 MHz 5510 5670 MHz No No No No No No Yes, Yes, Yes, Yes, Yes, Yes, Yes, No Yes, Yes, Yes, No No No passive scanning

(where the device is can listen only with no probes) Yes, Yes, Yes, Yes, Yes, Yes, Yes, No No No No No No No Yes, Yes, Yes, No No No Ad Hoc Mode capability Access point capability Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, No No No No No No No No No No Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, Yes, No No No No No No No No No No

(3) Country code selection ability -

If no, pls explain how was implemented : use network utility Yes , No

(4) Meet 15.202 requirement -

pls check below :

Yes , No , A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer. Apply , No Apply ,

(If apply , pls help to provide explanation on how it was implement (By hardware or software , and how software was controlled) If you have any questions, please feel free to contact me at the address shown below. Yours sincerely, Signatory Printed NameChaijue Ding

ZTE Corporation POWER OF ATTORNEY DATE: 3/10/2022 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 We, the undersigned, hereby authorize TA Technology (Shanghai) Co., Ltd. /

Zhou Yue on our behalf, to apply to FCC on our equipment for FCC ID:

SRQ-T3000. Any and all acts carried out by TA Technology (Shanghai) Co., Ltd. / Zhou Yue on our behalf shall have the same effect as acts of our own. Sincerely, Print name: Chaijue Ding Company: ZTE Corporation.