FCC ID: I88G570SV2 Wireless Access Point

G-570S v2 802.11g Wireless Access Point Users Guide Version 1.00 12/2006 Edition 2 www.zyxel.com About This User's Guide About This User's Guide Intended Audience This manual is intended for people who want to configure the ZyXEL Device using the web configurator. You should have at least a basic knowledge of TCP/IP networking concepts and topology. Related Documentation Quick Start Guide The Quick Start Guide is designed to help you get up and running right away. It contains information on setting up your network and configuring for Internet access. Web Configurator Online Help Embedded web help for descriptions of individual screens and supplementary information. Command Reference Guide The Command Reference Guide explains how to use the Command-Line Interface (CLI) and CLI commands to configure the ZyXEL Device.

It is recommended you use the web configurator to configure the ZyXEL Device. Supporting Disk Refer to the included CD for support documents. ZyXEL Web Site Please refer to www.zyxel.com for additional support documentation and product certifications. User Guide Feedback Help us help you. Send all User Guide-related comments, questions or suggestions for improvement to the following address, or use e-mail instead. Thank you!

The Technical Writing Team, ZyXEL Communications Corp., 6 Innovation Road II, Science-Based Industrial Park, Hsinchu, 300, Taiwan. E-mail: techwriters@zyxel.com.tw ZyXEL G-570S v2 Users Guide 3 Document Conventions Document Conventions Warnings and Notes These are how warnings and notes are shown in this Users Guide.

Warnings tell you about things that could harm you or your device.

Notes tell you other important information (for example, other things you may need to configure or helpful tips) or recommendations. Syntax Conventions The G-570S v2 may be referred to as the ZyXEL Device, the device, the system or the product in this Users Guide. Product labels, screen names, field labels and field choices are all in bold font. A key stroke is denoted by square brackets and uppercase text, for example, [ENTER]

means the enter or return key on your keyboard. Enter means for you to type one or more characters and then press the [ENTER] key. Select or choose means for you to use one of the predefined choices. A right angle bracket ( > ) within a screen name denotes a mouse click. For example, Maintenance > Log > Log Setting means you first click Maintenance in the navigation panel, then the Log sub menu and finally the Log Setting tab to get to that screen. Units of measurement may denote the metric value or the scientific value. For example, k for kilo may denote 1000 or 1024, M for mega may denote 1000000 or 1048576 and so on. 4 ZyXEL G-570S v2 Users Guide Document Conventions Icons Used in Figures Figures in this Users Guide may use the following generic icons. The ZyXEL Device icon is not an exact representation of your device. ZyXEL Device Computer Notebook computer Server DSLAM Firewall Telephone Switch Router ZyXEL G-570S v2 Users Guide 5 Safety Warnings Safety Warnings

For your safety, be sure to read and follow all warning notices and instructions. Do NOT use this product near water, for example, in a wet basement or near a swimming pool. Do NOT expose your device to dampness, dust or corrosive liquids. Do NOT store things on the device. Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning. Connect ONLY suitable accessories to the device. Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information. Make sure to connect the cables to the correct ports. Place connecting cables carefully so that no one will step on them or stumble over them. Always disconnect all cables from this device before servicing or disassembling. Use ONLY an appropriate power adaptor or cord for your device. Connect it to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe). Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor or cord. Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution. If the power adaptor or cord is damaged, remove it from the device and the power source. Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one. Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning. Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device. Antenna Warning! This device meets ETSI and FCC certification requirements when using the included antenna(s). Only use the included antenna(s). If you wall mount your device, make sure that no electrical lines, gas or water pipes will be damaged. This product is recyclable. Dispose of it properly. 6 ZyXEL G-570S v2 Users Guide Safety Warnings ZyXEL G-570S v2 Users Guide 7 Safety Warnings 8 ZyXEL G-570S v2 Users Guide Contents Overview Contents Overview Introduction and Wizards ......................................................................................................21 Introducing the ZyXEL Device ................................................................................................... 23

................................................................................................................................................... 30 Introducing the Web Configurator .............................................................................................. 31 Wizards ...................................................................................................................................... 35 Advanced ................................................................................................................................43 Navigating the Advanced Screens ............................................................................................ 45 Status Screens .......................................................................................................................... 47 System Screen .......................................................................................................................... 51 Wireless Screens ....................................................................................................................... 55 Management and Troubleshooting ......................................................................................87 Management Screens ............................................................................................................... 89 Troubleshooting ......................................................................................................................... 95 Appendices and Index ...........................................................................................................99 ZyXEL G-570S v2 Users Guide 9 Contents Overview 10 ZyXEL G-570S v2 Users Guide Table of Contents Table of Contents About This User's Guide ..........................................................................................................3 Document Conventions............................................................................................................4 Safety Warnings........................................................................................................................6 Contents Overview ...................................................................................................................9 Table of Contents....................................................................................................................11 List of Figures .........................................................................................................................15 List of Tables...........................................................................................................................19 Part I: Introduction and Wizards........................................................... 21 Chapter 1 Introducing the ZyXEL Device...............................................................................................23 1.1 Overview .............................................................................................................................. 23 1.2 Applications for the ZyXEL Device ...................................................................................... 23 1.2.1 Access Point for Internet Access ............................................................................... 23 1.2.2 Corporate Network Access Application ...................................................................... 24 1.2.3 Wireless Client Application ......................................................................................... 24 1.2.4 Bridge / Repeater ....................................................................................................... 25 1.2.5 Access Point and Repeater ........................................................................................ 26 1.3 Ways to Manage the ZyXEL Device .................................................................................... 26 1.4 Good Habits for Managing the ZyXEL Device ..................................................................... 27 1.5 LEDs .................................................................................................................................... 27 1.6 Management Computer Setup ............................................................................................ 28 1.6.1 Wired Connection ....................................................................................................... 28 1.6.2 Wireless Connection .................................................................................................. 28 1.7 Restarting the ZyXEL Device ............................................................................................... 29 1.8 Resetting the ZyXEL Device ................................................................................................ 29 1.8.1 Methods of Restoring Factory-Defaults ...................................................................... 29

..................................................................................................................................................30 Chapter 2 Introducing the Web Configurator ........................................................................................31 2.1 Web Configurator Overview ................................................................................................. 31 ZyXEL G-570S v2 Users Guide 11 Table of Contents 2.2 Accessing the Web Configurator ......................................................................................... 31 Chapter 3 Wizards ....................................................................................................................................35 3.1 Using the Wizards ............................................................................................................... 35 3.1.1 Wizard: Basic Settings .............................................................................................. 35 3.1.2 Wizard: Wireless Settings .......................................................................................... 36 3.1.3 Wizard: Security Settings ........................................................................................... 37 3.1.4 Wizard: Confirm Your Settings .................................................................................. 40 Part II: Advanced.................................................................................... 43 Chapter 4 Navigating the Advanced Screens........................................................................................45 4.0.1 Navigation Panel ........................................................................................................ 46 Chapter 5 Status Screens ........................................................................................................................47 5.1 System Status ..................................................................................................................... 47 5.1.1 Statistics .................................................................................................................... 48 5.1.2 Association List ......................................................................................................... 49 Chapter 6 System Screen ........................................................................................................................51 6.1 TCP/IP Parameters ............................................................................................................. 51 6.1.1 IP Address Assignment .............................................................................................. 51 6.1.2 IP Address and Subnet Mask ..................................................................................... 51 6.2 System Settings .................................................................................................................. 52 Chapter 7 Wireless Screens ....................................................................................................................55 7.1 Wireless Network Overview ................................................................................................. 55 7.2 Wireless Security Overview ................................................................................................. 56 7.2.1 SSID ........................................................................................................................... 56 7.2.2 MAC Address Filter .................................................................................................... 56 7.2.3 User Authentication .................................................................................................... 56 7.2.4 Encryption .................................................................................................................. 57 7.2.5 One-Touch Intelligent Security Technology (OTIST) .................................................. 58 7.3 Wireless Performance Overview ......................................................................................... 58 7.3.1 Quality of Service (QoS) ............................................................................................ 58 7.4 Additional Wireless Terms ................................................................................................... 58 12 ZyXEL G-570S v2 Users Guide Table of Contents 7.5 Quality of Service ................................................................................................................ 59 7.5.1 WMM QoS .................................................................................................................. 59 7.6 Configuring Wireless ........................................................................................................... 60 7.6.1 Access Point Mode ................................................................................................... 60 7.6.2 Wireless Client Mode ................................................................................................ 62 7.6.3 The Site Survey Window ............................................................................................ 64 7.6.4 Bridge Mode .............................................................................................................. 65 7.6.5 AP+Repeater Mode .................................................................................................. 69 7.7 Configuring Wireless Security ............................................................................................. 72 7.7.1 Wireless Security: Disable ........................................................................................ 73 7.7.2 Wireless Security: WEP ............................................................................................ 73 7.7.3 Wireless Security: WPA(2)-PSK ................................................................................ 75 7.7.4 Wireless Security: WPA(2) ........................................................................................ 75 7.7.5 Wireless Security: IEEE 802.1x ................................................................................ 77 7.8 MAC Filter ........................................................................................................................... 78 7.9 OTIST ................................................................................................................................. 81 7.9.1 Enabling OTIST .......................................................................................................... 81 7.9.2 Starting OTIST ........................................................................................................... 83 7.9.3 Notes on OTIST ......................................................................................................... 84 Part III: Management and Troubleshooting ......................................... 87 Chapter 8 Management Screens.............................................................................................................89 8.1 Maintenance Overview ........................................................................................................ 89 8.2 Password ............................................................................................................................ 89 8.3 Logs .................................................................................................................................... 90 8.4 Configuration File ............................................................................................................... 91 8.4.1 Backup Configuration ................................................................................................. 91 8.4.2 Restore Configuration ................................................................................................ 92 8.4.3 Back to Factory Defaults ............................................................................................ 93 8.5 F/W Upload Screen ............................................................................................................ 93 Chapter 9 Troubleshooting......................................................................................................................95 9.1 Power, Hardware Connections, and LEDs .......................................................................... 95 9.2 ZyXEL Device Access and Login ........................................................................................ 96 9.3 Internet Access .................................................................................................................... 98 Part IV: Appendices and Index ............................................................. 99 ZyXEL G-570S v2 Users Guide 13 Table of Contents Appendix A Product Specifications.......................................................................................101 Appendix B Setting up Your Computers IP Address............................................................107 Appendix C Pop-up Windows, JavaScripts and Java Permissions......................................123 Appendix D Wireless LANs ..................................................................................................129 Appendix E Customer Support.............................................................................................143 Appendix F Legal Information ..............................................................................................147 Index.......................................................................................................................................151 14 ZyXEL G-570S v2 Users Guide List of Figures List of Figures Figure 1 Internet Access Application ...................................................................................................... 24 Figure 2 Corporate Network Application ................................................................................................. 24 Figure 3 Wireless Client Application ...................................................................................................... 25 Figure 4 Bridge Application .................................................................................................................... 25 Figure 5 Bridge Repeater Application ..................................................................................................... 26 Figure 6 AP+Repeater Application ......................................................................................................... 26 Figure 7 LEDs ......................................................................................................................................... 27 Figure 8 Wired Connection ..................................................................................................................... 28 Figure 9 Wireless Connection ................................................................................................................ 28 Figure 10 Web Configurator Address ..................................................................................................... 32 Figure 11 Login Screen .......................................................................................................................... 32 Figure 12 Language Screen ................................................................................................................... 32 Figure 13 Select Wizard or Advanced Setup Screen ............................................................................. 33 Figure 14 Wizard: Basic Settings ........................................................................................................... 36 Figure 15 Wizard: Wireless Settings ...................................................................................................... 37 Figure 16 Setup Wizard 3: Disable ......................................................................................................... 38 Figure 17 Wizard 3: WEP ....................................................................................................................... 39 Figure 18 Wizard 3: WPA(2)-PSK .......................................................................................................... 40 Figure 19 Wizard: Confirm Your Settings ............................................................................................... 41 Figure 20 Status Screen ......................................................................................................................... 45 Figure 21 Status ..................................................................................................................................... 47 Figure 22 Status: View Statistics ............................................................................................................. 49 Figure 23 Status: View Association List .................................................................................................. 50 Figure 24 Status: View Association List: Wireless Client Mode .............................................................. 50 Figure 25 System Settings ..................................................................................................................... 52 Figure 26 Example of a Wireless Network ............................................................................................. 55 Figure 27 Wireless Settings: Access Point ............................................................................................. 60 Figure 28 Wireless Settings: Wireless Client .......................................................................................... 63 Figure 29 Wireless Client Mode: the Site Survey Screen ....................................................................... 64 Figure 30 Bridging Example ................................................................................................................... 66 Figure 31 Bridge Loop: Two Bridges Connected to Hub ........................................................................ 66 Figure 32 Bridge Loop: Bridge Connected to Wired LAN ....................................................................... 67 Figure 33 Wireless Settings: Bridge ....................................................................................................... 67 Figure 34 Wireless Settings: AP+Repeater ............................................................................................ 70 Figure 35 Wireless Security: Disable ...................................................................................................... 73 Figure 36 Wireless Security: WEP ......................................................................................................... 74 Figure 37 Wireless Security: WPA(2)-PSK ............................................................................................. 75 Figure 38 Wireless Security: WPA(2) ..................................................................................................... 76 ZyXEL G-570S v2 Users Guide 15 List of Figures Figure 39 Wireless Security: 802.1x ....................................................................................................... 77 Figure 40 MAC Filter .............................................................................................................................. 80 Figure 41 OTIST ..................................................................................................................................... 82 Figure 42 Example Wireless Client OTIST Screen ................................................................................ 82 Figure 43 ZyXEL Device in Wireless Client Mode: OTIST Screen ......................................................... 83 Figure 44 Security Key ........................................................................................................................... 83 Figure 45 OTIST in Progress (AP) ......................................................................................................... 84 Figure 46 OTIST in Progress (Client) ..................................................................................................... 84 Figure 47 No AP with OTIST Found ....................................................................................................... 84 Figure 48 Start OTIST? .......................................................................................................................... 84 Figure 49 Management: Password ......................................................................................................... 89 Figure 50 Management: Logs ................................................................................................................. 90 Figure 51 Management: Configuration File ............................................................................................ 91 Figure 52 Configuration Upload Successful ........................................................................................... 92 Figure 53 Network Temporarily Disconnected ........................................................................................ 92 Figure 54 Configuration Upload Error ..................................................................................................... 93 Figure 55 Reset Warning Message ........................................................................................................ 93 Figure 56 Management: F/W Upload ..................................................................................................... 93 Figure 57 Firmware Upgrading Screen .................................................................................................. 94 Figure 58 Network Temporarily Disconnected ........................................................................................ 94 Figure 59 Firmware Upload Error ........................................................................................................... 94 Figure 60 WIndows 95/98/Me: Network: Configuration ........................................................................ 108 Figure 61 Windows 95/98/Me: TCP/IP Properties: IP Address ............................................................ 109 Figure 62 Windows 95/98/Me: TCP/IP Properties: DNS Configuration .................................................110 Figure 63 Windows XP: Start Menu .......................................................................................................111 Figure 64 Windows XP: Control Panel ..................................................................................................111 Figure 65 Windows XP: Control Panel: Network Connections: Properties ............................................112 Figure 66 Windows XP: Local Area Connection Properties ..................................................................112 Figure 67 Windows XP: Internet Protocol (TCP/IP) Properties .............................................................113 Figure 68 Windows XP: Advanced TCP/IP Properties ..........................................................................114 Figure 69 Windows XP: Internet Protocol (TCP/IP) Properties .............................................................115 Figure 70 Macintosh OS 8/9: Apple Menu .............................................................................................116 Figure 71 Macintosh OS 8/9: TCP/IP ....................................................................................................116 Figure 72 Macintosh OS X: Apple Menu ...............................................................................................117 Figure 73 Macintosh OS X: Network .....................................................................................................118 Figure 74 Red Hat 9.0: KDE: Network Configuration: Devices ............................................................119 Figure 75 Red Hat 9.0: KDE: Ethernet Device: General .....................................................................119 Figure 76 Red Hat 9.0: KDE: Network Configuration: DNS ................................................................. 120 Figure 77 Red Hat 9.0: KDE: Network Configuration: Activate .......................................................... 120 Figure 78 Red Hat 9.0: Dynamic IP Address Setting in ifconfig-eth0 ................................................. 121 Figure 79 Red Hat 9.0: Static IP Address Setting in ifconfig-eth0 ..................................................... 121 Figure 80 Red Hat 9.0: DNS Settings in resolv.conf .......................................................................... 121 Figure 81 Red Hat 9.0: Restart Ethernet Card ................................................................................... 121 16 ZyXEL G-570S v2 Users Guide List of Figures Figure 82 Red Hat 9.0: Checking TCP/IP Properties ......................................................................... 122 Figure 83 Pop-up Blocker ..................................................................................................................... 123 Figure 84 Internet Options: Privacy ...................................................................................................... 124 Figure 85 Internet Options: Privacy ...................................................................................................... 125 Figure 86 Pop-up Blocker Settings ....................................................................................................... 125 Figure 87 Internet Options: Security ..................................................................................................... 126 Figure 88 Security Settings - Java Scripting ......................................................................................... 127 Figure 89 Security Settings - Java ........................................................................................................ 127 Figure 90 Java (Sun) ............................................................................................................................ 128 Figure 91 Peer-to-Peer Communication in an Ad-hoc Network ........................................................... 129 Figure 92 Basic Service Set ................................................................................................................. 130 Figure 93 Infrastructure WLAN ............................................................................................................. 131 Figure 94 RTS/CTS ............................................................................................................................. 132 Figure 95 WPA(2) with RADIUS Application Example ......................................................................... 139 Figure 96 WPA(2)-PSK Authentication ................................................................................................. 140 ZyXEL G-570S v2 Users Guide 17 List of Figures 18 ZyXEL G-570S v2 Users Guide List of Tables List of Tables Table 1 Front Panel LED Description .................................................................................................... 27 Table 2 Factory Defaults ........................................................................................................................ 29 Table 3 Global Icon Key ......................................................................................................................... 45 Table 4 Screens Summary .................................................................................................................... 46 Table 5 Status ........................................................................................................................................ 47 Table 6 Status: View Statistics ............................................................................................................... 49 Table 7 Status: View Association List .................................................................................................... 50 Table 8 Status: View Association List: Wireless Client Mode ................................................................ 50 Table 9 Private IP Address Ranges ....................................................................................................... 51 Table 10 System Settings ...................................................................................................................... 52 Table 11 Types of Encryption for Each Type of Authentication .............................................................. 57 Table 12 Additional Wireless Terms ....................................................................................................... 58 Table 13 WMM QoS Priorities ............................................................................................................... 59 Table 14 Wireless Settings: Access Point ............................................................................................. 60 Table 15 Wireless Settings: Wireless Client .......................................................................................... 63 Table 16 Wireless: the AP Survey Screen ............................................................................................. 65 Table 17 Wireless Settings: Bridge ........................................................................................................ 68 Table 18 Wireless Settings: AP + Repeater ........................................................................................... 70 Table 19 Wireless Security: Disable ...................................................................................................... 73 Table 20 Wireless Security: WEP .......................................................................................................... 74 Table 21 Wireless Security: WPA-PSK .................................................................................................. 75 Table 22 Wireless Security: WPA(2) ...................................................................................................... 76 Table 23 Wireless Security: 802.1x ....................................................................................................... 78 Table 24 MAC Filter ............................................................................................................................... 80 Table 25 OTIST ..................................................................................................................................... 82 Table 26 Management: Password ......................................................................................................... 89 Table 27 Management: Logs ................................................................................................................. 90 Table 28 Management: Configuration File: Restore Configuration ........................................................ 92 Table 29 Management: F/W Upload ...................................................................................................... 94 Table 30 Hardware Specifications ....................................................................................................... 101 Table 31 Feature Specifications ........................................................................................................... 101 Table 32 Wireless Specifications ......................................................................................................... 104 Table 33 Approvals .............................................................................................................................. 104 Table 34 Power Adaptor Specifications ............................................................................................... 105 Table 35 IEEE 802.11g ........................................................................................................................ 133 Table 36 Wireless Security Levels ....................................................................................................... 134 Table 37 Comparison of EAP Authentication Types ............................................................................ 137 Table 38 Wireless Security Relational Matrix ...................................................................................... 140 ZyXEL G-570S v2 Users Guide 19 List of Tables 20 ZyXEL G-570S v2 Users Guide Introduction and PART I Wizards Introducing the ZyXEL Device (23) Introducing the Web Configurator (31) Wizards (35) 21 22 CHAPTER 1 Introducing the ZyXEL Device This chapter introduces the main applications and features of the ZyXEL Device. It also introduces the ways you can manage the ZyXEL Device. 1.1 Overview The ZyXEL Device is a 4-in-1 Access Point with Super G and Turbo G wireless technology. Access Point (AP), repeater, bridge and wireless client functions allow you to use the ZyXEL Device in various network deployments. Super G and Turbo G technology boost the wireless data throughput. The ZyXEL Device Access Point (AP) allows wireless stations to communicate and/or access a wired network. It can work as a bridge and repeater to extend your wireless network. You can also use it as a wireless client to access a wired network through another AP. The ZyXEL Device uses IEEE 802.1x, WEP data encryption, WPA (Wi-Fi Protected Access), WPA2 and MAC address filtering to give mobile users highly secured wireless connectivity. Both IEEE 802.11b and IEEE 802.11g compliant wireless devices can associate with the ZyXEL Device. In addition to being highly flexible, the ZyXEL Device is easy to install and configure. 1.2 Applications for the ZyXEL Device Here are some application examples of how you can use your ZyXEL Device. 1.2.1 Access Point for Internet Access The ZyXEL Device is an ideal access solution for wireless Internet connection. A typical Internet access application for your ZyXEL Device is shown as follows. ZyXEL G-570S v2 Users Guide 23 Chapter 1 Introducing the ZyXEL Device Figure 1 Internet Access Application 1.2.2 Corporate Network Access Application In situations where users need to access corporate network resources and the Internet, the ZyXEL Device is an ideal solution for wireless stations to connect to the corporate network without expensive network cabling. Stations A, B and C can access the wired network through the ZyXEL Devices. The following figure depicts a typical application of the ZyXEL Device in an enterprise environment. The three computers with wireless adapters are allowed to access the network resource through the ZyXEL Device after account validation by the network authentication server. Figure 2 Corporate Network Application 1.2.3 Wireless Client Application The ZyXEL Device can function as a wireless client to connect to a network via an Access Point (AP). The AP provides access to the wired network and the Internet. 24 ZyXEL G-570S v2 Users Guide Figure 3 Wireless Client Application Chapter 1 Introducing the ZyXEL Device 1.2.4 Bridge / Repeater The ZyXEL Device can act as a wireless network bridge and establish wireless links with other APs. The ZyXEL Devices in the following example are using bridge mode with a star configuration. A, B, C and D are connected to independent wired networks and have bridge connections at the same time (B, C and D can communicate with A). Figure 4 Bridge Application A ZyXEL Device in bridge mode without an Ethernet connection can function as a repeater. It transmits traffic from one AP to another AP without using a wired connection. C in the following graphic repeats wireless traffic between A and B. ZyXEL G-570S v2 Users Guide 25 Chapter 1 Introducing the ZyXEL Device Figure 5 Bridge Repeater Application 1.2.5 Access Point and Repeater Set the ZyXEL Device to AP+Repeater mode to have it simultaneously provide access for wireless clients and use the repeater function. This allows you to extend the coverage of your wireless network without installing Ethernet cable to connect the ZyXEL Device. In the following figure, B is in AP+Repeater mode. B functions as an AP for wireless clients C and D. B also repeats traffic between the wireless clients and AP A which is connected to the wired network. You could also set AP A to AP+Repeater mode so that wireless clients could connect to A as well. Figure 6 AP+Repeater Application 1.3 Ways to Manage the ZyXEL Device Use any of the following methods to manage the ZyXEL Device. Web Configurator. This is recommended for everyday management of the ZyXEL Device using a (supported) web browser. Command Line Interface. Line commands are mostly used for troubleshooting by service engineers. FTP. Use File Transfer Protocol for firmware upgrades and configuration backup/restore. 26 ZyXEL G-570S v2 Users Guide Chapter 1 Introducing the ZyXEL Device 1.4 Good Habits for Managing the ZyXEL Device Do the following things regularly to make the ZyXEL Device more secure and to manage the ZyXEL Device more effectively. Change the password. Use a password thats not easy to guess and that consists of different types of characters, such as numbers and letters. Write down the password and put it in a safe place. Back up the configuration (and make sure you know how to restore it). Restoring an earlier working configuration may be useful if the device becomes unstable or even crashes. If you forget your password, you will have to reset the ZyXEL Device to its factory default settings. If you backed up an earlier configuration file, you would not have to totally re-configure the ZyXEL Device. You could simply restore your last configuration. 1.5 LEDs Figure 7 LEDs The following table describes the LEDs on the ZyXEL Device. Table 1 Front Panel LED Description LED PWR COLOR Green STATUS Blinking On ETHN Green Amber OTIST Green Off Blinking On Blinking On Off Blinking On Off DESCRIPTION The ZyXEL Device is not ready or rebooting. The ZyXEL Device has rebooted successfully and is receiving power. The ZyXEL Device is not receiving power. The ZyXEL Device is sending/receiving data. The ZyXEL Device has a successful 10Mbps Ethernet connection. The ZyXEL Device is sending/receiving data. The ZyXEL Device has a successful 100Mbps Ethernet connection. The ZyXEL Device does not have an Ethernet connection. The OTIST automatic wireless configuration is in progress. The OTIST feature is activated on the ZyXEL Device. The OTIST feature is not activated or activated but the wireless settings have been changed. ZyXEL G-570S v2 Users Guide 27 Chapter 1 Introducing the ZyXEL Device Table 1 Front Panel LED Description LED WLAN STATUS Blinking COLOR Green DESCRIPTION The ZyXEL Device is sending or receiving data through the wireless LAN. The ZyXEL Device is ready, but is not sending/receiving data. On 1.6 Management Computer Setup You can connect a computer to the ZyXEL Device for management purposes either using an Ethernet connection (recommended for a first time management session) or wirelessly. 1.6.1 Wired Connection You must prepare your computer/computer network to connect to the ZyXEL Device if you are using a wired connection. Your computer's IP address and subnet mask must be on the same subnet as the ZyXEL Device. This can be done by setting up your computer's IP address. See the appendix for details on how to set up your IP address. The following figure shows an example of accessing your ZyXEL Device via a wired connection with an Ethernet cable. Figure 8 Wired Connection Default IP Address:

192.168.1.2 192.168.1.3 1.6.2 Wireless Connection Ensure that the wireless stations have a compatible wireless card/adapter with the same wireless settings as the ZyXEL Device. The following figure shows how you can access your ZyXEL Device wirelessly. Figure 9 Wireless Connection SSID: ZyXEL G-

570S Channel: 6 28 ZyXEL G-570S v2 Users Guide Chapter 1 Introducing the ZyXEL Device

The wireless stations and the ZyXEL Device must use the same SSID, channel and wireless security settings for wireless communication.

If you do not enable any wireless security on your ZyXEL Device, your network traffic is visible to any wireless networking device that is within range. 1.7 Restarting the ZyXEL Device Press and immediately release the RESET button to restart the ZyXEL Device.

Holding the RESET button in for five seconds or longer resets the device to the factory-default settings. 1.8 Resetting the ZyXEL Device If you forget the ZyXEL Device's IP address or your password, to access the ZyXEL Device, you will need to reload the factory-default using the RESET button. Resetting the ZyXEL Device replaces the current configuration file with the factory-default configuration file. This means that you will lose all configurations that you had previously. The following parameters will be reset to the default values. Table 2 Factory Defaults PARAMETER IP Address Password Wireless Security SSID DEFAULT VALUE 192.168.1.2 1234 Disabled ZyXEL G-570S v2 1.8.1 Methods of Restoring Factory-Defaults You can erase the current configuration and restore factory defaults in two ways:

1 Use the RESET button on the ZyXEL Device to upload the default configuration file

(hold this button in for at least five seconds). 2 Use the web configurator. Click System > Management > Configuration File. From here you can restore the ZyXEL Device to its factory default settings. ZyXEL G-570S v2 Users Guide 29 Chapter 1 30 ZyXEL G-570S v2 Users Guide CHAPTER 2 Introducing the Web Configurator This chapter describes how to configure the ZyXEL Device using the Wizard. 2.1 Web Configurator Overview The web configurator is an HTML-based management interface that allows easy ZyXEL Device setup and management via Internet browser. Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later versions. The recommended screen resolution is 1024 by 768 pixels. In order to use the web configurator you need to allow:

Web browser pop-up windows from your device. Web pop-up blocking is enabled by default in Windows XP SP (Service Pack) 2. JavaScripts (enabled by default). Java permissions (enabled by default). See the Troubleshooting chapter for details on how to make sure these functions are allowed in Internet Explorer or Netscape Navigator. 2.2 Accessing the Web Configurator Follow the steps below to access the web configurator, select a language, change your login password and choose a configuration method from the status screen. 1 Make sure your ZyXEL Device hardware is properly connected (refer to the Quick Start 2 Prepare your computer/computer network to connect to the ZyXEL Device (refer to the appendix on setting up your IP address). 3 Launch your web browser. 4 Type the IP address of the ZyXEL Device (192.168.1.2 is the default) in the URL bar. Guide). Press Enter. ZyXEL G-570S v2 Users Guide 31 Chapter 2 Introducing the Web Configurator Figure 10 Web Configurator Address 5 Type "1234" (default) as the password and click Login. Figure 11 Login Screen Default password is 1234. 6 Select your language and click Apply. Figure 12 Language Screen 7 The following screen displays. Select Go Wizard Setup and click Apply to use the wizard setup screens for initial configuration (see Chapter 3 on page 35). Select Go Advanced Setup and click Apply to go directly to the advanced screens (see Chapter 4 on page 45). 32 ZyXEL G-570S v2 Users Guide Figure 13 Select Wizard or Advanced Setup Screen Chapter 2 Introducing the Web Configurator ZyXEL G-570S v2 Users Guide 33 Chapter 2 Introducing the Web Configurator 34 ZyXEL G-570S v2 Users Guide CHAPTER 3 Wizards This chapter shows you how to configure the ZyXEL Devices basic features using the wizards. 3.1 Using the Wizards The wizards consist of a series of screens to help you configure your ZyXEL Device for wireless stations to access your wired LAN. Use the following buttons to navigate the Wizard:

Back Next No configuration changes will be saved to the ZyXEL Device until you click Finish. Click Back to return to the previous screen. Click Next to continue to the next screen. 3.1.1 Wizard: Basic Settings First, log into the ZyXEL Device as shown in Section 2.2 on page 31. Click SETUP WIZARD to display the first wizard screen shown next. Refer to the System Screens chapter for more background information. 1 Enter a descriptive name to identify the device in the Ethernet network. 2 Select Obtain IP Address Automatically if you want to put the device behind a router that assigns an IP address. If you select this by mistake, use the RESET button to restore the factory default IP address. 3 Select Use fixed IP Address to give the device a static IP address. The IP address you configure here is used for management of the device (accessing the web configurator). 4 Enter a Subnet Mask appropriate to your network and the Gateway IP Address of the neighboring device, if you know it. If you do not, leave the Gateway IP Address field as 0.0.0.0. ZyXEL G-570S v2 Users Guide 35 Chapter 3 Wizards Figure 14 Wizard: Basic Settings Do not select this unless you have a router that can assign the ZyXEL Device an IP address. 3.1.2 Wizard: Wireless Settings Use this wizard screen to set up the wireless LAN. See the chapter on the wireless screens for background information. 1 The SSID is a unique name to identify the device in a wireless network. Enter up to 32 printable characters. Spaces are allowed. If you change this field on the device, make sure all wireless stations use the same SSID in order to access the network. 2 A wireless device uses a channel to communicate in a wireless network. Select a channel that is not already in use by a neighboring wireless device.

The wireless stations and this device must use the same SSID, channel and wireless security settings for wireless communication. 36 ZyXEL G-570S v2 Users Guide Figure 15 Wizard: Wireless Settings Chapter 3 Wizards 3.1.3 Wizard: Security Settings Use this screen to configure security for your wireless LAN. The screen varies depending on what you select in the Encryption Method field. Select Disable to have no wireless security configured, select WEP, or select WPA-PSK if your wireless clients support WPA-PSK. Select WPA2-PSK if your wireless clients support WPA2-PSK Go to Wireless > Security if you want WPA2, WPA or 802.1x. See Chapter 7 on page 55 for background information. 3.1.3.1 Disable Select Disable to have no wireless LAN security configured. If you do not enable any wireless security on your device, your network is accessible to any wireless networking device that is within range.

With no wireless security a neighbor can access and see traffic in your network. ZyXEL G-570S v2 Users Guide 37 Chapter 3 Wizards Figure 16 Setup Wizard 3: Disable 3.1.3.2 WEP 1 WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless network. Select 64-bit, 128-bit or 152-bit from the WEP Encryption drop-

down list box and then follow the on-screen instructions to set up the WEP keys. 2 Choose an encryption level from the drop-down list. The higher the WEP encryption, the higher the security but the slower the throughput. 3 You can generate or manually enter a WEP key. If you selected 64-bit or 128-bit WEP, you can enter a Passphrase (up to 32 printable characters) and click Generate. The device automatically generates WEP keys. One key displays in the Key 1 field. Go to Wireless > Security if you want to see the other WEP keys. or Enter a manual key in the Key 1 field. 38 ZyXEL G-570S v2 Users Guide Figure 17 Wizard 3: WEP Chapter 3 Wizards Use Passphrase to automatically generate keys or manually enter a key in the Key 1 field. 3.1.3.3 WPA(2)-PSK Only select WPA-PSK or WPA2-PSK if your wireless clients support it. Type a pre-shared key from 8 to 63 ASCII characters (including spaces and symbols). This field is case-sensitive. ZyXEL G-570S v2 Users Guide 39 Chapter 3 Wizards Figure 18 Wizard 3: WPA(2)-PSK 3.1.4 Wizard: Confirm Your Settings This read-only screen shows the status of the current settings. Use the summary table to check whether what you have configured is correct. Click Finish to complete the wizard configuration and save your settings. 40 ZyXEL G-570S v2 Users Guide Figure 19 Wizard: Confirm Your Settings Chapter 3 Wizards For more detailed background information, see the rest of this User's Guide. ZyXEL G-570S v2 Users Guide 41 Chapter 3 Wizards 42 ZyXEL G-570S v2 Users Guide PART II Advanced Navigating the Advanced Screens (45) Status Screens (47) System Screen (51) Wireless Screens (55) 43 44 CHAPTER 4 Navigating the Advanced Screens The Status screen is the first advanced screen that displays. This section explains how to navigate the advanced configuration screens. See Chapter 5 on page 47 for details about the individual screen. Figure 20 Status Screen The following table describes the global web configurator icons (in the upper right corner of most screens). Table 3 Global Icon Key ICON DESCRIPTION Click the Wizard icon to open the setup wizard. Click the About icon to view copyright information. Click the Logout icon at any time to exit the web configurator. Make sure you save any changes before you log out. ZyXEL G-570S v2 Users Guide 45 Chapter 4 Navigating the Advanced Screens 4.0.1 Navigation Panel After you enter the password, use the links on the navigation panel to go to the various advanced screens. The following table describes the sub-menus. Table 4 Screens Summary LINK Status TAB System Wireless Management Wireless Settings Security MAC Filter OTIST Password Logs Configuration F/W Upload FUNCTION This screen shows the ZyXEL Devices general device, system and interface status information. Use this screen to access the wizard, and summary statistics tables. Use this screen to configure the device name and IP address assignment settings. Use this screen to configure the wireless LAN. Use this screen to configure the wireless LANs security settings. Use the MAC filter screen to configure the ZyXEL Device to block or allow only certain devices to associate with the ZyXEL Device. When the ZyXEL Device is in access point mode, this screen allows you to assign wireless clients the ZyXEL Devices wireless security settings. When the ZyXEL Device is in wireless client mode, this screen allows the ZyXEL Device to get security settings from an OTIST-enabled access point. Use this screen to configure the administrator password. Use this screen to view logs and alert messages. Use this screen to backup and restore the configuration or reset the factory defaults to your ZyXEL Device. Use this screen to upload firmware to your ZyXEL Device.

See the rest of this User's Guide for configuration details and background information on all features using the web configurator. 46 ZyXEL G-570S v2 Users Guide CHAPTER 5 Status Screens This chapter describes the Status screens. 5.1 System Status Click Status to open the following screen. The Status screen display a snapshot of your devices settings. You can also view network statistics and a list of wireless stations currently associated with your device. Note that these labels are READ-ONLY and are meant to be used for diagnostic purposes. Figure 21 Status The following table describes the labels in this screen. Table 5 Status LABEL Refresh Interval DESCRIPTION Use the drop-down list box to select how often you want the device to renew the information on this screen. Click this button to have the device renew the information on this screen. Refresh Now Device Information Device Name Operation Mode This is the same as the device name you entered in the first wizard screen if you entered one there. It is for identification purposes. This field shows whether the device is functioning as an access point, a wireless client, a bridge or an access point and repeater. ZyXEL G-570S v2 Users Guide 47 Chapter 5 Status Screens Table 5 Status LABEL MAC Address Firmware Version IP Settings DESCRIPTION This field displays the MAC address of the device. The MAC (Media Access Control) or Ethernet address on a LAN (Local Area Network) is unique to your computer. A network interface card such as an Ethernet adapter has a hardwired address that is assigned at the factory. This address follows an industry standard that ensures no other adapter has a similar address. This is the firmware version and the date the firmware was created. IP Address Subnet Mask Gateway IP Address This is the Ethernet port IP address. This is the Ethernet port subnet mask. This is the IP address of a gateway. Leave this field as 0.0.0.0 if you do not know it. Wireless Settings SSID Channel Encryption Method MAC Filter View Statistics View Association List This is the descriptive name used to identify the device in a wireless network. This field displays the radio channel the device is currently using. This field shows the type of data encryption that is enabled on the wireless network:

WEP (WEP or 802.1x) TKIP (WPA or WPA-PSK) AES (WPA2 or WPA2-PSK) TKIP + AES (WPA & WPA2 or WPA-PSK & WPA2-PSK) or Disable (no security) This field shows whether MAC filter is enabled or not. With MAC filtering, you can allow or deny access to the device based on the MAC addresses of the wireless stations. Click View Statistics to see performance statistics such as number of packets sent and number of packets received. Click View Association List to show the wireless stations that are currently associated to the device. 5.1.1 Statistics Click View Statistics in the Status screen. This screen displays read-only information including port status and packet specific statistics. Also provided are "system up time" and

"poll interval(s)". The Poll Interval(s) field is configurable. 48 ZyXEL G-570S v2 Users Guide Figure 22 Status: View Statistics Chapter 5 Status Screens The following table describes the labels in this screen. Table 6 Status: View Statistics LABEL DESCRIPTION Ethernet Packets Bytes Wireless Unicast Packets Broadcast Packets Multicast Packets Total Packets Total Bytes System Up Time Poll Interval(s) Set Interval Stop This row displays the numbers of packets received and transmitted by the Ethernet port. This row displays the numbers of bytes received and transmitted by the Ethernet port. This row displays the numbers of unicast packets received and transmitted by the wireless adapter. This row displays the numbers of broadcast packets received and transmitted by the wireless adapter. This row displays the numbers of multicast packets received and transmitted by the wireless adapter. This row displays the numbers of all types of packets received and transmitted by the wireless adapter. This row displays the numbers of bytes received and transmitted by the wireless adapter. This is the total time the device has been on. Enter the time interval for refreshing statistics. Click this button to apply the new poll interval you entered above. Click this button to stop refreshing statistics. 5.1.2 Association List Click Status and then the View Association List button to display the Association List screen. When the device is not in wireless client mode, this screen displays which wireless stations are currently associated to the device in the Association List screen. ZyXEL G-570S v2 Users Guide 49 Chapter 5 Status Screens Figure 23 Status: View Association List The following table describes the labels in this screen. Table 7 Status: View Association List LABEL

MAC Address IP Address Signal Strength Status Rescan DESCRIPTION This is the index number of an associated wireless station. This field displays the MAC address of an associated wireless station. This field displays the IP address of an associated wireless station. This field displays the signal strength of each associated wireless station. This field displays Associated for associated wireless stations. Click Rescan to check for associated wireless stations. When the device is in wireless client mode, this screen displays details of the access point to which the ZyXEL Device is associated. Figure 24 Status: View Association List: Wireless Client Mode The following table describes the labels in this screen. Table 8 Status: View Association List: Wireless Client Mode LABEL

MAC Address IP Address Signal Strength Status Rescan DESCRIPTION This is the index number of an associated access point. This field displays the MAC address of the associated access point. This field displays the IP address of the associated access point. This field displays the signal strength of the associated access point. This field displays Associated for an associated access point. Click Rescan to check for associated wireless stations. 50 ZyXEL G-570S v2 Users Guide CHAPTER 6 System Screen This chapter provides information on the System screen. 6.1 TCP/IP Parameters 6.1.1 IP Address Assignment Every computer on the Internet must have a unique IP address. If your networks are isolated from the Internet, for instance, only between your two branch offices, you can assign any IP addresses to the hosts without problems. However, the Internet Assigned Numbers Authority

(IANA) has reserved the following three blocks of IP addresses specifically for private networks. Table 9 Private IP Address Ranges 10.0.0.0 - 10.255.255.255 172.16.0.0 - 172.31.255.255 192.168.0.0 - 192.168.255.255 You can obtain your IP address from the IANA, from an ISP or have it assigned by a private network. If you belong to a small organization and your Internet access is through an ISP, the ISP can provide you with the Internet addresses for your local networks. On the other hand, if you are part of a much larger organization, you should consult your network administrator for the appropriate IP addresses.

Regardless of your particular situation, do not create an arbitrary IP address;

always follow the guidelines above. For more information on address assignment, please refer to RFC 1597, Address Allocation for Private Internets and RFC 1466, Guidelines for Management of IP Address Space. 6.1.2 IP Address and Subnet Mask Similar to the way houses on a street share a common street name, computers on a LAN share one common network number. ZyXEL G-570S v2 Users Guide 51 Chapter 6 System Screen Where you obtain your network number depends on your particular situation. If the ISP or your network administrator assigns you a block of registered IP addresses, follow their instructions in selecting the IP addresses and the subnet mask. If the ISP did not explicitly give you an IP network number, then most likely you have a single user account and the ISP will assign you a dynamic IP address when the connection is established. The Internet Assigned Number Authority (IANA) reserved this block of addresses specifically for private use; please do not use any other number unless you are told otherwise. Let's say you select 192.168.1.0 as the network number; which covers 254 individual addresses, from 192.168.1.1 to 192.168.1.254 (zero and 255 are reserved). In other words, the first three numbers specify the network number while the last number identifies an individual computer on that network. Once you have decided on the network number, pick an IP address that is easy to remember, for instance, 192.168.1.2, for your device, but make sure that no other device on your network is using that IP address. The subnet mask specifies the network number portion of an IP address. Your device will compute the subnet mask automatically based on the IP address that you entered. You don't need to change the subnet mask computed by the device unless you are instructed to do otherwise. 6.2 System Settings Click System to open the System Settings screen. Figure 25 System Settings The following table describes the labels in this screen. Table 10 System Settings LABEL Device Name IP Address Assignment Obtain IP Address Automatically DESCRIPTION This name can be up to 30 printable characters long. Spaces are allowed. Select this option to have your device use a dynamically assigned IP address from a router each time. 52 ZyXEL G-570S v2 Users Guide Chapter 6 System Screen Table 10 System Settings LABEL Use fixed IP address IP Address Subnet Mask Gateway IP Address Apply Reset DESCRIPTION Select this option to have your device use a static IP address. When you select this option, fill in the fields below. Enter the IP address of your device in dotted decimal notation. Enter the subnet mask. Type the IP address of the gateway. The gateway is a router or switch on the same network segment as the device. The gateway helps forward packets to their destinations. Leave this field as 0.0.0.0 if you do not know it. Click Apply to save your changes back to the device. Click Reset to reload the previous configuration for this screen. ZyXEL G-570S v2 Users Guide 53 Chapter 6 System Screen 54 ZyXEL G-570S v2 Users Guide CHAPTER 7 Wireless Screens This chapter discusses how to configure the wireless network settings in your ZyXEL Device. See the appendices for more detailed information about wireless networks. 7.1 Wireless Network Overview The following figure provides an example of a wireless network. Figure 26 Example of a Wireless Network The wireless network is the part in the blue circle. In this wireless network, devices A and B use the access point (AP) to interact with the other devices (such as the printer) or with the Internet. Your ZyXEL Device is the AP. Every wireless network must follow these basic guidelines. Every device in the same wireless network must use the same SSID. The SSID is the name of the wireless network. It stands for Service Set IDentity. If two wireless networks overlap, they should use a different channel. ZyXEL G-570S v2 Users Guide 55 Chapter 7 Wireless Screens Like radio stations or television channels, each wireless network uses a specific channel, or frequency, to send and receive information. Every device in the same wireless network must use security compatible with the AP. Security stops unauthorized devices from using the wireless network. It can also protect the information that is sent in the wireless network. 7.2 Wireless Security Overview The following sections introduce different types of wireless security you can set up in the wireless network. 7.2.1 SSID Normally, the ZyXEL Device acts like a beacon and regularly broadcasts the SSID in the area. You can hide the SSID instead, in which case the ZyXEL Device does not broadcast the SSID. In addition, you should change the default SSID to something that is difficult to guess. This type of security is fairly weak, however, because there are ways for unauthorized wireless devices to get the SSID. In addition, unauthorized wireless devices can still see the information that is sent in the wireless network. 7.2.2 MAC Address Filter Every device that can use a wireless network has a unique identification number, called a MAC address.1 A MAC address is usually written using twelve hexadecimal characters2; for example, 00A0C5000002 or 00:A0:C5:00:00:02. To get the MAC address for each device in the wireless network, see the devices Users Guide or other documentation. You can use the MAC address filter to tell the ZyXEL Device which devices are allowed or not allowed to use the wireless network. If a device is allowed to use the wireless network, it still has to have the correct information (SSID, channel, and security). If a device is not allowed to use the wireless network, it does not matter if it has the correct information. This type of security does not protect the information that is sent in the wireless network. Furthermore, there are ways for unauthorized wireless devices to get the MAC address of an authorized device. Then, they can use that MAC address to use the wireless network. 7.2.3 User Authentication Authentication is the process of verifying whether a wireless device is allowed to use the wireless network. You can make every user log in to the wireless network before they can use it. However, every device in the wireless network has to support IEEE 802.1x to do this. For wireless networks, you can store the user names and passwords for each user in a RADIUS server. This is a server used in businesses more than in homes. If you do not have a RADIUS server, you cannot set up user names and passwords for your users. 1. Some wireless devices, such as scanners, can detect wireless networks but cannot use wireless networks. These kinds of wireless devices might not have MAC addresses. 2. Hexadecimal characters are 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, and F. 56 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens Unauthorized wireless devices can still see the information that is sent in the wireless network, even if they cannot use the wireless network. Furthermore, there are ways for unauthorized wireless users to get a valid user name and password. Then, they can use that user name and password to use the wireless network. 7.2.4 Encryption Wireless networks can use encryption to protect the information that is sent in the wireless network. Encryption is like a secret code. If you do not know the secret code, you cannot understand the message. The types of encryption you can choose depend on the type of authentication. (See Section 7.2.3 on page 56 for information about this.) Table 11 Types of Encryption for Each Type of Authentication Weakest NO AUTHENTICATION No Security Static WEP WPA-PSK Strongest WPA2-PSK RADIUS SERVER WPA WPA2 For example, if the wireless network has a RADIUS server, you can choose WPA or WPA2. If users do not log in to the wireless network, you can choose no encryption, Static WEP, WPA-

PSK, or WPA2-PSK. Usually, you should set up the strongest encryption that every device in the wireless network supports. For example, suppose you have a wireless network with the ZyXEL Device and you do not have a RADIUS server. Therefore, there is no authentication. Suppose the wireless network has two devices. Device A only supports WEP, and device B supports WEP and WPA. Therefore, you should set up Static WEP in the wireless network.

It is recommended that wireless networks use WPA-PSK, WPA, or stronger encryption. The other types of encryption are better than none at all, but it is still possible for unauthorized wireless devices to figure out the original information pretty quickly. When you select WPA2 or WPA2-PSK in your ZyXEL Device, you can also select an option

(WPA compatible) to support WPA as well. In this case, if some of the devices support WPA and some support WPA2, you should set up WPA2-PSK or WPA2 (depending on the type of wireless network login) and select the WPA compatible option in the ZyXEL Device. Many types of encryption use a key to protect the information in the wireless network. The longer the key, the stronger the encryption. Every device in the wireless network must have the same key. ZyXEL G-570S v2 Users Guide 57 Chapter 7 Wireless Screens 7.2.5 One-Touch Intelligent Security Technology (OTIST) With ZyXELs OTIST, you set up the SSID and the encryption (WEP or WPA-PSK) on the ZyXEL Device. Then, the ZyXEL Device transfers them to the devices in the wireless networks. As a result, you do not have to set up the SSID and encryption on every device in the wireless network. The devices in the wireless network have to support OTIST, and they have to be in range of the ZyXEL Device when you activate it. See Section 7.9 on page 81 for more details. 7.3 Wireless Performance Overview The following sections introduce different ways to improve the performance of the wireless network. 7.3.1 Quality of Service (QoS) You can turn on Wi-Fi MultiMedia (WMM) QoS to improve the performance of voice and video applications in the wireless network. QoS gives high priority to voice and video, which makes them run more smoothly. Similarly, it gives low priority to many large file downloads so that they do not reduce the quality of other applications. 7.4 Additional Wireless Terms RTS/CTS Threshold The following table describes wireless network terms and acronyms used in the ZyXEL Devices Web Configurator. Table 12 Additional Wireless Terms TERM DESCRIPTION This describes direct communication (not through the ZyXEL Device) between Intra-BSS Traffic two wireless devices within a wireless network. You might disable this kind of communication to enhance security within your wireless network. In a wireless network which covers a large area, wireless devices are sometimes not aware of each others presence. This may cause them to send information to the AP at the same time and result in information colliding and not getting through. By setting this value lower than the default value, the wireless devices must sometimes get permission to send information to the ZyXEL Device. The lower the value, the more often the devices must get permission. If this value is greater than the fragmentation threshold value (see below), then wireless devices never have to get permission to send information to the ZyXEL Device. A preamble affects the timing in your wireless network. There are two preamble modes: long and short. If a device uses a different preamble mode than the ZyXEL Device does, it cannot communicate with the ZyXEL Device. The process of verifying whether a wireless device is allowed to use the wireless network. Enable this to improve the performance of both pure IEEE 802.11g and mixed IEEE 802.11b/g networks. Maximum Frame Burst sets the maximum time that the ZyXEL Device transmits IEEE 802.11g wireless traffic only. Max. Frame Burst Authentication Preamble 58 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens Table 12 Additional Wireless Terms TERM DESCRIPTION A small fragmentation threshold is recommended for busy networks, while a Fragmentation Threshold larger threshold provides faster performance if the network is not very busy. Roaming If you have two or more ZyXEL Devices (or other wireless access points) on your wireless network, you can enable this option so that wireless devices can change locations without having to log in again. This is useful for devices, such as notebooks, that move around a lot. 7.5 Quality of Service This section discusses the Quality of Service (QoS) features available on the ZyXEL Device. 7.5.1 WMM QoS WMM (Wi-Fi MultiMedia) QoS (Quality of Service) ensures quality of service in wireless networks. It controls WLAN transmission priority on packets to be transmitted over the wireless network. WMM QoS prioritizes wireless traffic according to delivery requirements. WMM QoS is a part of the IEEE 802.11e QoS enhancement to certified Wi-Fi wireless networks. On APs without WMM QoS, all traffic streams are given the same access priority to the wireless network. If the introduction of another traffic stream creates a data transmission demand that exceeds the current network capacity, then the new traffic stream reduces the throughput of the other traffic streams. The ZyXEL Device uses WMM QoS to prioritize traffic streams according to the IEEE 802.1q tag or DSCP information in each packets header. The ZyXEL Device automatically determines the priority to use for an individual traffic stream. This prevents reductions in data transmission for applications that are sensitive to latency (delay) and jitter (variations in delay). 7.5.1.1 WMM QoS Priorities The following table describes the WMM QoS priority levels that the ZyXEL Device uses. Table 13 WMM QoS Priorities PRIORITY LEVEL voice

(WMM_VOICE) video

(WMM_VIDEO) best effort

(WMM_BEST_EFFORT) DESCRIPTION Typically used for traffic that is especially sensitive to jitter. Use this priority to reduce latency for improved voice quality. Typically used for traffic which has some tolerance for jitter but needs to be prioritized over other data traffic. Typically used for traffic from applications or devices that lack QoS capabilities. Use best effort priority for traffic that is less sensitive to latency, but is affected by long delays, such as Internet surfing. This is typically used for non-critical traffic such as bulk transfers and print jobs that are allowed but that should not affect other applications and users. Use background priority for applications that do not have strict latency and throughput requirements. background

(WMM_BACKGROUND) ZyXEL G-570S v2 Users Guide 59 Chapter 7 Wireless Screens 7.6 Configuring Wireless Click Wireless to display the Wireless Settings screen.The screen varies depending upon the operation mode you select. 7.6.1 Access Point Mode Select Access Point in the Operation Mode field to display the screen as shown next. This mode has the device act as an access point (AP) through which wireless stations can communicate and/or access a wired network. Figure 27 Wireless Settings: Access Point The following table describes the labels in this screen. Table 14 Wireless Settings: Access Point LABEL Basic Settings Operation Mode DESCRIPTION Select the operating mode from the drop-down list. The options are Access Point, Wireless Client, Bridge and AP+Repeater. 60 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens Table 14 Wireless Settings: Access Point (continued) LABEL SSID DESCRIPTION Wireless stations associating to the access point (AP) must have the same SSID. Enter a descriptive name (up to 32 printable characters) for the wireless LAN. Spaces are allowed. Note: If you are configuring the device from a computer connected to the wireless LAN and you change the device's SSID, channel or security settings, you will lose your wireless connection when you press Apply to confirm. You must then change the wireless settings of your computer to match the device's new settings. Select this check box to hide the SSID in the outgoing beacon frame so a station cannot obtain the SSID through passive scanning using a site survey tool. Set the operating frequency/channel depending on your particular region. Select a channel from the drop-down list box. Refer to the chapter on wizard setup for more information about channels. Select 802.11b only to allow only IEEE 802.11b compliant WLAN devices to associate with the device. Select 802.11g only to allow only IEEE 802.11g compliant WLAN devices to associate with the device. Select Auto (11g/11b) to allow either IEEE 802.11b or IEEE 802.11g compliant WLAN devices to associate with the device. The transmission rate of your device might be reduced. Set the number of milliseconds that should pass between the sending out of beacons. Intra-BSS traffic is traffic between wireless stations in the same BSS. Enable Intra-BSS traffic to allow wireless stations connected to the device to communicate with each other. Disable Intra-BSS traffic to only allow wireless stations to communicate with the wired network, not with each other. Set the interval for wireless clients in sleep mode to wake up and check for multicast or broadcast traffic. The AP includes a Delivery Traffic Indication Message (DTIM) in the beacon to notify wireless clients in sleep mode that there is a multicast or broadcast packet awaiting delivery. The interval is a multiple of the beacon interval. For example, if the beacon interval is 100 milliseconds and the DTIM interval is 2, the AP includes a DTIM with every second beacon (or every 200 milliseconds). Select this to turn on WMM QoS (Wireless MultiMedia Quality of Service). The ZyXEL Device assigns priority to packets based on the 802.1q or DSCP information in their headers. If a packet has no WMM information in its header, it is assigned the default priority. Use this field to set a maximum number of wireless stations that may connect to the device. Enter the number (from 1 to 32) of wireless stations allowed. Turn on the wireless adapter to allow wireless communications between the device and other IEEE 802.11b and IEEE 802.11g compliant wireless devices. Turn off the wireless adapter to stop wireless communications between the device and other IEEE 802.11b and IEEE 802.11g compliant wireless devices. Hide SSID Channel Wireless Mode Advanced Settings Beacon Interval Intra-BSS Traffic DTIM Interval WMM Number of Wireless Stations Allowed to Associate:

Radio Enable ZyXEL G-570S v2 Users Guide 61 Chapter 7 Wireless Screens Table 14 Wireless Settings: Access Point (continued) LABEL Output Power Management Data Rate Management Preamble Type DESCRIPTION Set the output power of the device in this field. If there is a high density of APs within an area, decrease the output power of the device to reduce interference with other APs. The options are Full, 50%, 25%, 12% and Min. Use this field to select a maximum data rate for the wireless connection(s). Please note that this is a total rate to be shared by all of the devices wireless connections. Preamble is used to signal that data is coming to the receiver. Short preamble increases performance as less time sending preamble means more time for sending data. All IEEE 802.11b compliant wireless adapters support long preamble, but not all support short preamble. Select Long preamble if you are unsure what preamble mode the wireless adapters support, and to provide more reliable communications in busy wireless networks. Select Dynamic to have the device automatically use short preamble when all wireless clients support it, otherwise the device uses long preamble. Note: The device and the wireless stations MUST use the same preamble mode in order to communicate. Super-G Mode Super-G mode provides higher speed transmissions than regular IEEE 802.11g. The other device must also support super-G mode in order for the device to use it for the wireless connection. This is available when you select a Wireless Mode that includes IEEE 802.11g. Turbo-G Mode Turbo-G mode provides higher speed transmissions than regular IEEE 802.11g or super-G mode. The other device must also support turbo-G mode in order for the device to use it for the wireless connection. This is available when you select a Wireless Mode that includes IEEE 802.11g. Turbo-G uses two channels bonded together in order to achieve its higher transmission rates. This may cause interference with other APs in the area. The Channel field is automatically fixed at 6 when you use turbo-G mode. Enter a value between 0 and 2346. The default is 2346. RTS/CTS Threshold Fragmentation Enter a value between 256 and 2346. The default is 2346. It is the maximum data Apply Reset fragment size that can be sent. Click Apply to save your changes back to the device. Click Reset to begin configuring this screen afresh. 7.6.2 Wireless Client Mode Select Wireless Client in the Operation Mode field to display the screen as shown next. This mode has the device act as wireless client to connect to a wireless network.

WPA, WPA2 and IEEE 802.1x wireless security are not available when you use Wireless Client, Bridge or AP+Repeater mode. 62 ZyXEL G-570S v2 Users Guide Figure 28 Wireless Settings: Wireless Client Chapter 7 Wireless Screens The following table describes the labels in this screen. Table 15 Wireless Settings: Wireless Client LABEL Basic Settings Operation Mode SSID DESCRIPTION Select the operating mode from the drop-down list. The options are Access Point, Wireless Client, Bridge and AP+Repeater. Wireless stations associating to the access point (AP) must have the same SSID. Enter a descriptive name (up to 32 printable characters) for the wireless LAN. Spaces are allowed. Note: If you are configuring the device from a computer connected to the wireless LAN and you change the device's SSID, channel or security settings, you will lose your wireless connection when you click Apply to save your settings. You must then change the wireless settings of your computer to match the device's new settings. Site Survey Click this button to see details of access points (APs) within range. Advanced Settings Manual MAC Cloning Radio Enable Every Ethernet-capable device is issued with a unique Media Access Control

(MAC) address at the factory. This address is used to identify the device across a network. Your ZyXEL Device is capable of cloning, or emulating, the MAC addresses of one or more other devices. Select the check box and enter the MAC address you want to clone. Turn on the wireless adapter to allow wireless communications between the device and other IEEE 802.11b and IEEE 802.11g compliant wireless devices. Turn off the wireless adapter to stop wireless communications between the device and other IEEE 802.11b and IEEE 802.11g compliant wireless devices. ZyXEL G-570S v2 Users Guide 63 Chapter 7 Wireless Screens Table 15 Wireless Settings: Wireless Client (continued) LABEL Output Power Management Data Rate Management Preamble Type DESCRIPTION Set the output power of the device in this field. If there is a high density of APs within an area, decrease the output power of the device to reduce interference with other APs. The options are Full, 50%, 25%, 12% and Min. Use this field to select a maximum data rate for the wireless connection(s). Please note that this is a total rate to be shared by all of the devices wireless connections. Preamble is used to signal that data is coming to the receiver. Short preamble increases performance as less time sending preamble means more time for sending data. All IEEE 802.11b compliant wireless adapters support long preamble, but not all support short preamble. Select Long preamble if you are unsure what preamble mode the wireless adapters support, and to provide more reliable communications in busy wireless networks. Select Dynamic to have the device automatically use short preamble when all wireless clients support it, otherwise the device uses long preamble. Note: The device and the wireless stations MUST use the same preamble mode in order to communicate. Super-G Mode Super-G mode provides higher speed transmissions than regular IEEE 802.11g. The other device must also support super-G mode in order for the device to use it for the wireless connection. This is available when you select a Wireless Mode that includes IEEE 802.11g. When Super-G Mode is enabled, the ZyXEL Device in wireless client mode can also connect to a turbo-G enabled wireless access point. Enter a value between 0 and 2346. The default is 2346. RTS/CTS Threshold Fragmentation Enter a value between 256 and 2346. The default is 2346. It is the maximum data Apply Reset fragment size that can be sent. Click Apply to save your changes back to the device. Click Reset to begin configuring this screen afresh. 7.6.3 The Site Survey Window Click on the Site Survey button in the Wireless > Wireless Settings screen (when the ZyXEL Device is in Wireless Client mode) to display the Site Survey screen. The ZyXEL Device searches for available access points (APs). Use this screen to view details of wireless access points within range. Figure 29 Wireless Client Mode: the Site Survey Screen 64 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens The following table describes the labels in this screen. Table 16 Wireless: the AP Survey Screen LABEL Site Survey DESCRIPTION SSID BSSID Channel Wireless Mode Security Signal Strength Rescan This field displays the SSID (Service Set IDentifier) of each access point. This field displays the MAC address of each access point. This field displays the channel number used by each access point. This field displays the wireless networking standard the access point is using. This field displays details of the access points security and data encryption settings. This field displays the signal strength of each access point. Click Rescan to have the ZyXEL Device search again for available access points. 7.6.4 Bridge Mode The device can act as a wireless network bridge and establish wireless links with other APs. You need to know the MAC address of the peer device, which also must be in bridge mode. When two devices connect in Bridge mode, they form a WDS (Wireless Distribution System) allowing the computers in one LAN to connect to the computers in another LAN. See the following example.

WPA, WPA2 and IEEE 802.1x wireless security are not available when you use Wireless Client, Bridge or AP+Repeater mode.

You can use only WEP or WPA2-PSK keys to encrypt traffic between APs. ZyXEL G-570S v2 Users Guide 65 Chapter 7 Wireless Screens Figure 30 Bridging Example Be careful to avoid bridge loops when you enable bridging in the ZyXEL Device. Bridge loops cause broadcast traffic to circle the network endlessly, resulting in possible throughput degradation and disruption of communications. The following examples show two network topologies that can lead to this problem:

If two or more ZyXEL Devices (in bridge mode) are connected to the same hub as shown next. Figure 31 Bridge Loop: Two Bridges Connected to Hub If your ZyXEL Device (in bridge mode) is connected to a wired LAN while communicating with another wireless bridge that is also connected to the same wired LAN as shown next. 66 ZyXEL G-570S v2 Users Guide Figure 32 Bridge Loop: Bridge Connected to Wired LAN Chapter 7 Wireless Screens To prevent bridge loops, ensure that your ZyXEL Device is not set to bridge mode while connected to both wired and wireless segments of the same LAN. Select Bridge as the Operation Mode to have the device act as a wireless bridge only. Figure 33 Wireless Settings: Bridge ZyXEL G-570S v2 Users Guide 67 Chapter 7 Wireless Screens The following table describes the labels in this screen. Table 17 Wireless Settings: Bridge LABEL Basic Settings Operation Mode DESCRIPTION Select the operating mode from the drop-down list. The options are Access Point, Wireless Client, Bridge and AP+Repeater. Note: If you are configuring the device from a computer connected to the wireless LAN and you change the device to use bridge mode, you will lose your wireless connection when you click Apply to save your settings. You must then connect to the device through the wired network. Set the operating frequency/channel depending on your particular region. Select a channel from the drop-down list box. Refer to the chapter on wizard setup for more information about channels. Select 802.11b only to allow only IEEE 802.11b compliant WLAN devices to associate with the device. Select 802.11g only to allow only IEEE 802.11g compliant WLAN devices to associate with the device. Select Auto (11g/11b) to allow either IEEE 802.11b or IEEE 802.11g compliant WLAN devices to associate with the device. The transmission rate of your device might be reduced. This is the MAC address of the device. Type the MAC address of the peer device(s) (the other access point(s) in your network) in a valid MAC address format, that is, six hexadecimal character pairs, for example, 12:34:56:78:9a:bc. Turn on the wireless adapter to allow wireless communications between the device and other IEEE 802.11b and IEEE 802.11g compliant wireless devices. Turn off the wireless adapter to stop wireless communications between the device and other IEEE 802.11b and IEEE 802.11g compliant wireless devices. Set the output power of the device in this field. If there is a high density of APs within an area, decrease the output power of the device to reduce interference with other APs. The options are Full, 50%, 25%, 12% and Min. Use this field to select a maximum data rate for the wireless connection(s). Please note that this is a total rate to be shared by all of the devices wireless connections. Channel Wireless Mode WDS Settings Local MAC Address Remote MAC Address 1~4 Advanced Settings Radio Enable Output Power Management Data Rate Management 68 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens Table 17 Wireless Settings: Bridge (continued) LABEL Preamble Type DESCRIPTION Preamble is used to signal that data is coming to the receiver. Short preamble increases performance as less time sending preamble means more time for sending data. All IEEE 802.11b compliant wireless adapters support long preamble, but not all support short preamble. Select Long preamble if you are unsure what preamble mode the wireless adapters support, and to provide more reliable communications in busy wireless networks. Select Dynamic to have the device automatically use short preamble when all wireless clients support it, otherwise the device uses long preamble. Note: The device and the wireless stations MUST use the same preamble mode in order to communicate. Super-G Mode Super-G mode provides higher speed transmissions than regular IEEE 802.11g. The other device must also support super-G mode in order for the device to use it for the wireless connection. This is available when you select a Wireless Mode that includes IEEE 802.11g. Turbo-G Mode Turbo-G mode provides higher speed transmissions than regular IEEE 802.11g or super-G mode. The other device must also support turbo-G mode in order to use it for the wireless connection. This is available when you select a Wireless Mode that includes IEEE 802.11g. Turbo-G uses two channels bonded together in order to achieve its higher transmission rates. This may cause interference with other APs in the area. The Channel field is automatically fixed at 6 when you use turbo-G mode. Enter a value between 0 and 2346. The default is 2346. RTS/CTS Threshold Fragmentation Enter a value between 256 and 2346. The default is 2346. It is the maximum data Apply Reset fragment size that can be sent. Click Apply to save your changes back to the device. Click Reset to begin configuring this screen afresh. 7.6.5 AP+Repeater Mode Select AP+Repeater as the Operation Mode to have the device act as an access point and a wireless bridge. ZyXEL G-570S v2 Users Guide 69 Chapter 7 Wireless Screens Figure 34 Wireless Settings: AP+Repeater The following table describes the labels in this screen. Table 18 Wireless Settings: AP + Repeater LABEL Basic Settings Operation Mode DESCRIPTION Select the operating mode from the drop-down list. The options are Access Point, Wireless Client, Bridge and AP+Repeater. 70 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens Table 18 Wireless Settings: AP + Repeater (continued) LABEL SSID DESCRIPTION Wireless stations associating to the access point (AP) must have the same SSID. Enter a descriptive name (up to 32 printable characters) for the wireless LAN. Spaces are allowed. Note: If you are configuring the device from a computer connected to the wireless LAN and you change the device's SSID, channel or security settings, you will lose your wireless connection when you click Apply to save your settings. You must then change the wireless settings of your computer to match the device's new settings. Select this check box to hide the SSID in the outgoing beacon frame so a station cannot obtain the SSID through passive scanning using a site survey tool. Set the operating frequency/channel depending on your particular region. Select a channel from the drop-down list box. Refer to the chapter on wizard setup for more information about channels. Select 802.11b only to allow only IEEE 802.11b compliant WLAN devices to associate with the device. Select 802.11g only to allow only IEEE 802.11g compliant WLAN devices to associate with the device. Select Auto (11g/11b) to allow either IEEE 802.11b or IEEE 802.11g compliant WLAN devices to associate with the device. The transmission rate of your device might be reduced. This is the MAC address of the device. Type the MAC address of the peer device in a valid MAC address format, that is, six hexadecimal character pairs, for example, 12:34:56:78:9a:bc. Set the number of milliseconds that should pass between the sending out of beacons. Intra-BSS traffic is traffic between wireless stations in the same BSS. Enable Intra-BSS traffic to allow wireless stations connected to the device to communicate with each other. Disable Intra-BSS traffic to only allow wireless stations to communicate with the wired network, not with each other. Set the interval for wireless clients in sleep mode to wake up and check for multicast or broadcast traffic. The AP includes a Delivery Traffic Indication Message (DTIM) in the beacon to notify wireless clients in sleep mode that there is a multicast or broadcast packet awaiting delivery. The interval is a multiple of the beacon interval. For example, if the beacon interval is 100 milliseconds and the DTIM interval is 2, the AP includes a DTIM with every second beacon (or every 200 milliseconds). Select this to turn on WMM QoS (Wireless MultiMedia Quality of Service). The ZyXEL Device assigns priority to packets based on the 802.1q or DSCP information in their headers. If a packet has no WMM information in its header, it is assigned the default priority. Hide SSID Channel Wireless Mode WDS Settings Local MAC Address Remote MAC Address 1~4 Advanced Settings Beacon Interval Intra-BSS Traffic DTIM Interval WMM ZyXEL G-570S v2 Users Guide 71 Chapter 7 Wireless Screens Table 18 Wireless Settings: AP + Repeater (continued) LABEL DESCRIPTION Use this field to set a maximum number of wireless stations that may connect to the device. Enter the number (from 1 to 32) of wireless stations allowed. Number of Wireless Stations Allowed to Associate:

Radio Enable Output Power Management Data Rate Management Preamble Type Turn on the wireless adapter to allow wireless communications between the device and other IEEE 802.11b and IEEE 802.11g compliant wireless devices. Turn off the wireless adapter to stop wireless communications between the device and other IEEE 802.11b and IEEE 802.11g compliant wireless devices. Set the output power of the device in this field. If there is a high density of APs within an area, decrease the devices output power to reduce interference with other APs. The options are Full, 50%, 25%, 12% and Min. Use this field to select a maximum data rate for the wireless connection(s). Please note that this is a total rate to be shared by all of the devices wireless connections. Preamble is used to signal that data is coming to the receiver. Short preamble increases performance as less time sending preamble means more time for sending data. All IEEE 802.11b compliant wireless adapters support long preamble, but not all support short preamble. Select Long preamble if you are unsure what preamble mode the wireless adapters support, and to provide more reliable communications in busy wireless networks. Select Dynamic to have the device automatically use short preamble when all wireless clients support it, otherwise the device uses long preamble. Note: The device and the wireless stations MUST use the same preamble mode in order to communicate. Super-G Mode Super-G mode provides higher speed transmissions than regular IEEE 802.11g. The other device must also support super-G mode in order to use it for the wireless connection. This is available when you select a Wireless Mode that includes IEEE 802.11g. Turbo-G Mode Turbo-G mode provides higher speed transmissions than regular IEEE 802.11g or super-G mode. The other device must also support turbo-G mode in order to use it for the wireless connection. This is available when you select a Wireless Mode that includes IEEE 802.11g. Turbo-G uses two channels bonded together in order to achieve its higher transmission rates. This may cause interference with other APs in the area. The Channel field is automatically fixed at 6 when you use turbo-G mode. Enter a value between 0 and 2436. The default is 2436. RTS/CTS Threshold Fragmentation Enter a value between 256 and 2436. The default is 2436. It is the maximum data Apply Reset fragment size that can be sent. Click Apply to save your changes back to the device. Click Reset to begin configuring this screen afresh. 7.7 Configuring Wireless Security Click Wireless > Security to display the Security screen. This screen varies according to the encryption method you select. 72 ZyXEL G-570S v2 Users Guide

The encryption methods available depend on the Operation Mode you select in the Wireless > Wireless screen. Chapter 7 Wireless Screens 7.7.1 Wireless Security: Disable If you do not enable any wireless security on your device, your network is accessible to any wireless networking device that is within range. Figure 35 Wireless Security: Disable The following table describes the labels in this screen. Table 19 Wireless Security: Disable LABEL Encryption Method Apply Reset Click Apply to save your changes back to the device. Click Reset to begin configuring this screen afresh. DESCRIPTION Select Disable to have no wireless LAN security configured. 7.7.2 Wireless Security: WEP WEP provides a mechanism for encrypting data using encryption keys. Both the AP and the wireless stations must use the same WEP key to encrypt and decrypt data. You can configure up to four 64-bit, 128-bit or 152-bit WEP keys, but only one key can be used at any one time. ZyXEL G-570S v2 Users Guide 73 Chapter 7 Wireless Screens Figure 36 Wireless Security: WEP The following table describes the labels in this screen. Table 20 Wireless Security: WEP DESCRIPTION LABEL Select WEP if you want to configure WEP encryption parameters. Encryption Method Authentication Type WEP Encryption Passphrase Select Auto, Open or Shared from the drop-down list box. Select 64 bit WEP, 128 bit WEP or 152 bit WEP to enable data encryption. If you selected 64-bit or 128-bit WEP, you can enter a passphrase (password phrase) of up to 32 case-sensitive printable characters and click Generate to have the device create four different WEP keys. After you enter the passphrase, click Generate to have the device generates four different WEP keys automatically. If you want to manually set the WEP keys, enter the WEP key in the field provided. Select a WEP key to use for data encryption. The WEP keys are used to encrypt data. Both the device and the wireless stations must use the same WEP key for data transmission. If you chose 64 bit WEP, then enter any 5 ASCII characters or 10 hexadecimal characters ("0-9", "A-F"). If you chose 128 bit WEP, then enter 13 ASCII characters or 26 hexadecimal characters ("0-9", "A-F"). If you chose 152 bit WEP, then enter 16 ASCII characters or 32 hexadecimal characters ("0-9", "A-F"). Click Apply to save your changes back to the device. Click Reset to begin configuring this screen afresh. Generate Key 1 to Key 4 Apply Reset 74 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens 7.7.3 Wireless Security: WPA(2)-PSK Select WPA-PSK, WPA2-PSK or WPA-PSK & WPA2-PSK in the Encryption Method drop down list-box to display the screen displays as next. Figure 37 Wireless Security: WPA(2)-PSK The following table describes the labels in this screen. Table 21 Wireless Security: WPA-PSK LABEL Encryption Method DESCRIPTION Select WPA-PSK, WPA2-PSK or WPA-PSK & WPA2-PSK if you want to configure a pre-shared key. Choose this option only if your wireless clients support it. The encryption mechanisms used for WPA and WPA-PSK are the same. The only difference between the two is that WPA-PSK uses a simple common password, instead of user-specific credentials. Type a pre-shared key from 8 to 63 ASCII characters (including spaces and symbols). This field is case-sensitive. Click Apply to save your changes back to the device. Click Reset to begin configuring this screen afresh. Pre-Shared Key Apply Reset 7.7.4 Wireless Security: WPA(2) WPA (Wi-Fi Protected Access) is a subset of the IEEE 802.11i standard. WPA2 (IEEE 802.11i) is a wireless security standard that defines stronger encryption, authentication and key management than WPA. Key differences between WPA(2) and WEP are user authentication and improved data encryption. ZyXEL G-570S v2 Users Guide 75 Chapter 7 Wireless Screens Figure 38 Wireless Security: WPA(2) The following table describes the labels in this screen. Table 22 Wireless Security: WPA(2) LABEL Encryption Method DESCRIPTION Select WPA, WPA2 or WPA & WPA2 to configure user authentication and improved data encryption. Note: WPA, WPA2 and IEEE 802.1x wireless security are not available when you use Wireless Client, Bridge or AP+Repeater mode. Note: You can only use WEP keys to encrypt traffic between APs. Enter the IP address of the external authentication server in dotted decimal notation. Enter the port number of the external authentication server. The default port number is 1812. You need not change this value unless your network administrator instructs you to do so with additional information. Enter a password (up to 63 printable characters) as the key to be shared between the external authentication server and the device. The key must be the same on the external authentication server and your device. The key is not sent over the network. Specify how often wireless stations have to resend user names and passwords in order to stay connected. Enter a time interval between 100 and 3600 seconds. If wireless station authentication is done using a RADIUS server, the reauthentication timer on the RADIUS server has priority. This is how often the AP sends a new group key out to all clients. The re-keying process is the WPA equivalent of automatically changing the WEP key for an AP and all stations in a WLAN on a periodic basis. Specify an interval either in seconds or thousands of packets that the device sends. Authentication Server IP Address Port Number Shared Secret Reauthentication Time Global-Key Update 76 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens Table 22 Wireless Security: WPA(2) (continued) LABEL Apply Reset DESCRIPTION Click Apply to save your changes back to the device. Click Reset to begin configuring this screen afresh. 7.7.5 Wireless Security: IEEE 802.1x The IEEE 802.1x standard outlines enhanced security methods for both the authentication of wireless stations and encryption key management.

Once you enable user authentication, you need to specify an external RADIUS server on the device for authentication. Figure 39 Wireless Security: 802.1x ZyXEL G-570S v2 Users Guide 77 Chapter 7 Wireless Screens The following table describes the labels in this screen. Table 23 Wireless Security: 802.1x LABEL Encryption Method DESCRIPTION Select 802.1X to configure authentication of wireless stations and encryption key management. Note: WPA, WPA2 and IEEE 802.1x wireless security are not available when you use Bridge or AP+Repeater mode. You can only use WEP keys to encrypt traffic between APs. Select None to allow wireless stations to communicate with the access points without using dynamic WEP key exchange. Select 64 bits WEP, 128 bits WEP or 152 bits WEP to enable data encryption. Up to 32 stations can access the device when you configure dynamic WEP key exchange. Enter the IP address of the external authentication server in dotted decimal notation. Enter the port number of the external authentication server. The default port number is 1812. You need not change this value unless your network administrator instructs you to do so with additional information. Enter a password (up to 63 printable characters) as the key to be shared between the external authentication server and the device. The key must be the same on the external authentication server and your device. The key is not sent over the network. Specify how often wireless stations have to resend user names and passwords in order to stay connected. Enter a time interval between 100 and 3600 seconds. If wireless station authentication is done using a RADIUS server, the reauthentication timer on the RADIUS server has priority. This is how often the AP sends a new group key out to all clients. The re-keying process is the WPA equivalent of automatically changing the WEP key for an AP and all stations in a WLAN on a periodic basis. Specify an interval either in seconds or thousands of packets that the device sends. Click Apply to save your changes back to the device. Click Reset to begin configuring this screen afresh. Data Encryption Authentication Server IP Address Port Number Shared Secret Reauthentication Time Global-Key Update Apply Reset 7.8 MAC Filter The MAC filter screen allows you to give exclusive access to up to 32 devices (Allow Association) or exclude up to 32 devices from accessing the device (Deny Association). Every Ethernet device has a unique MAC (Media Access Control) address. The MAC address is assigned at the factory and consists of six pairs of hexadecimal characters, for example, 00:A0:C5:00:00:02. You need to know the MAC addresses of the devices to configure this screen. The MAC filter works when the device functions as an AP. It allows or denies wireless client access. The MAC filter does not apply to bridge or repeater functions. 78 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens The following applies if you set the device to client mode and want to connect to an AP that uses a MAC filter. After the device turns on in client mode, it clones the MAC address of the first packets that it receives from devices connected to the Ethernet port. It uses this MAC address on the packets that it sends to an AP. All of the packets that the device sends to an AP will appear to be from the first device that connected to the Ethernet port. If you turn the device off and back on, it again clones the MAC address of the first packets that it receives from devices connected to the Ethernet port. You may be able to check the association list on the AP to determine which MAC address the device is currently using. To change your device's MAC filter settings, click Wireless > MAC Filter. The screen appears as shown.

Be careful not to list your computer's MAC address and select Deny the following MAC address to associate when managing the device via a wireless connection. This would lock you out. ZyXEL G-570S v2 Users Guide 79 Chapter 7 Wireless Screens Figure 40 MAC Filter The following table describes the labels in this screen. Table 24 MAC Filter LABEL Active DESCRIPTION Select the check box to enable MAC address filtering and define the filter action for the list of MAC addresses in the MAC address filter table. Select Allow the following MAC address to associate to permit access to the device. MAC addresses not listed will be denied access to the device. Select Deny the following MAC address to associate to block access to the device. MAC addresses not listed will be allowed to access the device. This is the index number of the MAC address. Enter the MAC addresses (in XX:XX:XX:XX:XX:XX format) of the wireless station that are allowed or denied access to the device in these address fields. Click Apply to save your changes back to the device. Click Reset to begin configuring this screen afresh.

MAC Address Apply Reset 80 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens 7.9 OTIST In a wireless network, the wireless clients must have the same SSID and security settings as the access point (AP) or wireless router (we will refer to both as AP here) in order to associate with it. Traditionally this meant that you had to configure the settings on the AP and then manually configure the exact same settings on each wireless client. OTIST (One-Touch Intelligent Security Technology) allows you to transfer your APs SSID and WEP or WPA-PSK security settings to wireless clients that support OTIST and are within transmission range. You can also choose to have OTIST generate a WPA-PSK key for you if you didnt configure one manually.

OTIST replaces the pre-configured wireless settings on the wireless clients.

OTIST is not available in AP+Repeater or Bridge mode at the time of writing. 7.9.1 Enabling OTIST You must enable OTIST on both the AP and wireless client before you start transferring settings.

The AP and wireless client(s) MUST use the same Setup key. 7.9.1.1 ZyXEL Device in AP Mode You can enable OTIST using the OTIST button or the web configurator. 7.9.1.1.1 OTIST Button If you use the OTIST button, the default (01234567) or previous saved (through the web configurator) Setup key is used to encrypt the settings that you want to transfer. Hold in the OTIST button for one or two seconds. 7.9.1.1.2 Web Configurator Click Wireless > OTIST in AP, AP+Repeater or Bridge mode to configure and enable OTIST. The screen appears as shown. ZyXEL G-570S v2 Users Guide 81 Chapter 7 Wireless Screens Figure 41 OTIST The following table describes the labels in this screen. Table 25 OTIST LABEL One-Touch Intelligent Security Technology Setup Key DESCRIPTION Enter the setup key of up to eight printable characters. The default OTIST setup key is "01234567". Yes!

Start Note: If you change the OTIST setup key here, you must also make the same change on the wireless client(s). To have OTIST automatically generate a WPA-PSK key, select this check box. If you manually configured a WEP key or a WPA-PSK key and you also select this check box, then the key you manually configured is used. Click Start to encrypt the wireless security data using the setup key and have the device set the wireless client to use the same wireless settings as the device. You must also activate and start OTIST on the wireless client at the same time. The process takes three minutes to complete. 7.9.1.2 Wireless Client Start the ZyXEL utility and click the Adapter tab. Select the OTIST check box, enter the same Setup Key as your APs and click Save. Figure 42 Example Wireless Client OTIST Screen 7.9.1.3 ZyXEL Device in Wireless Client Mode If you are using the ZyXEL Device in Wireless Client mode, you can enable OTIST using either the OTIST button or the web configurator. 82 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens 7.9.1.3.1 Wireless Client Mode: OTIST Button If you use the OTIST button, the default (01234567) or previous saved (through the web configurator) Setup key is used. Double-click the OTIST button to automatically change the ZyXEL Device to wireless client mode and start OTIST. 7.9.1.3.2 Wireless Client Mode: Web Configurator Start the web configurator and click Wireless. Select Wireless Client in the Operation Mode field. Click on the OTIST tab. The screen displays as shown. Enter the same Setup Key as your APs. Click Start when you are ready to begin OTIST. Figure 43 ZyXEL Device in Wireless Client Mode: OTIST Screen 7.9.2 Starting OTIST

You must click Start in the AP OTIST web configurator screen and in the wireless client(s) Adapter screen all within three minutes (at the time of writing). You can start OTIST in the wireless clients and AP in any order but they must all be within range and have OTIST enabled. 1 In the AP, a web configurator screen pops up showing you the security settings to transfer. After reviewing the settings, click OK. Figure 44 Security Key 2 This screen appears while OTIST settings are being transferred. It closes when the transfer is complete. ZyXEL G-570S v2 Users Guide 83 Chapter 7 Wireless Screens Figure 45 OTIST in Progress (AP) Figure 46 OTIST in Progress (Client) In the wireless client, you see this screen if it can't find an OTIST-enabled AP (with the same Setup key). Click OK to go back to the ZyXEL utility main screen. Figure 47 No AP with OTIST Found If there is more than one OTIST-enabled AP within range, you see a screen asking you to select one AP to get settings from. 7.9.3 Notes on OTIST 1 If you enabled OTIST in the wireless client, you see this screen each time you start the utility. Click Yes for it to search for an OTIST-enabled AP. Figure 48 Start OTIST?

2 If an OTIST-enabled wireless client loses its wireless connection for more than ten seconds, it will search for an OTIST-enabled AP for up to one minute. (If you manually have the wireless client search for an OTIST-enabled AP, there is no timeout; click Cancel in the OTIST progress screen to stop the search.) 84 ZyXEL G-570S v2 Users Guide Chapter 7 Wireless Screens 3 When the wireless client finds an OTIST-enabled AP, you must still click Start in the AP OTIST web configurator screen or hold in the OTIST button (for one or two seconds) for the AP to transfer settings. 4 If you change the SSID or the keys on the AP after using OTIST, you need to run OTIST again or enter them manually in the wireless client(s). 5 If you configure OTIST to generate a WPA-PSK key, this key changes each time you run OTIST. Therefore, if a new wireless client joins your wireless network, you need to run OTIST on the AP and ALL wireless clients again. ZyXEL G-570S v2 Users Guide 85 Chapter 7 Wireless Screens 86 ZyXEL G-570S v2 Users Guide PART III Management and Troubleshooting Management Screens (89) Troubleshooting (95) 87 88 CHAPTER 8 Management Screens This chapter describes the Maintenance screens. 8.1 Maintenance Overview Use these maintenance screens to change the password, view logs, back up or restore the ZyXEL Devices configuration and change the web configurator language. 8.2 Password To change your device's password (recommended), click Management. The screen appears as shown. This screen allows you to change the device's password. If you forget your password (or the device IP address), you will need to reset the device. See the section on resetting the device for details. Figure 49 Management: Password The following table describes the labels in this screen. Table 26 Management: Password LABEL Current Password Type in your existing system password (1234 is the default password). New Password DESCRIPTION Type your new system password (up to 30 printable characters). Spaces are not allowed. Note that as you type a password, the screen displays an asterisk (*) for each character you type. Retype to Confirm Retype your new system password for confirmation. ZyXEL G-570S v2 Users Guide 89 Chapter 8 Management Screens Table 26 Management: Password (continued) LABEL Apply Cancel DESCRIPTION Click Apply to save your changes back to the device. Click Cancel to reload the previous configuration for this screen. 8.3 Logs Click Management > Logs to open the Logs screen. You can view logs and alert messages in this screen. Once the log table is full, old logs are deleted as new logs are created. Click a column heading to sort the entries. A triangle indicates the direction of the sort order. Figure 50 Management: Logs The following table describes the labels in this screen. Table 27 Management: Logs LABEL Display Refresh Clear Log

Time DESCRIPTION Select a category of logs to view. Click Refresh to renew the log screen. Click Clear Log to clear all the logs. This is the logs index number. This field displays the time the log was recorded. It is the number of seconds since the last time the system turned on. This field states the reason for the log. This field lists the source IP address and the port number of the incoming packet that caused the log. This field lists the destination IP address and the port number of the outgoing packet that caused the log. This field displays additional information about the log entry. Message Source Destination Note 90 ZyXEL G-570S v2 Users Guide Chapter 8 Management Screens 8.4 Configuration File The configuration file (often called the romfile or rom-0) contains the factory default settings such as password and TCP/IP Setup, etc. It arrives from ZyXEL with a .rom filename extension. Once you have customized the device's settings, they can be saved back to your computer under a filename of your choosing. Click Management > Configuration File. Information related to factory defaults, backup configuration, and restoring configuration appears as shown next. Figure 51 Management: Configuration File 8.4.1 Backup Configuration Backup configuration allows you to back up (save) the device's current configuration to a file on your computer. Once your device is configured and functioning properly, it is highly recommended that you back up your configuration file before making configuration changes. The backup configuration file will be useful in case you need to return to your previous settings. Click Backup to save the device's current configuration to your computer. ZyXEL G-570S v2 Users Guide 91 Chapter 8 Management Screens 8.4.2 Restore Configuration Restore configuration allows you to upload a new or previously saved configuration file from your computer to your device. Table 28 Management: Configuration File: Restore Configuration LABEL File Path DESCRIPTION Type in the location of the file you want to upload in this field or click Browse ... to find it. Click Browse... to find the file you want to upload. Remember that you must decompress compressed (.zip) files before you can upload them. Click Upload to begin the upload process. Browse... Upload

Do not turn off the device while configuration file upload is in progress. The following screen displays. You must wait one minute before logging into the device again. Figure 52 Configuration Upload Successful The device automatically restarts in this time causing a temporary network disconnect. In some operating systems, you may see the following icon on your desktop. Figure 53 Network Temporarily Disconnected If you uploaded the default configuration file you may need to change the IP address of your computer to be in the same subnet as that of the default device IP address (192.168.1.2). If the upload was not successful, the following screen will appear. Click Return to go back to the Configuration File screen. 92 ZyXEL G-570S v2 Users Guide Figure 54 Configuration Upload Error Chapter 8 Management Screens 8.4.3 Back to Factory Defaults Clicking the RESET button in this section clears all user-entered configuration information and returns the device to its factory defaults. The following warning screen will appear. Figure 55 Reset Warning Message You can also press the RESET button on the rear panel to reset the factory defaults of your device. Refer to the section on resetting the device for more information on the RESET button. 8.5 F/W Upload Screen Find firmware at www.zyxel.com in a file that (usually) uses the system model name with a

.rmt extension, for example, "zyxel.rmt". The upload process uses HTTP (Hypertext Transfer Protocol) and may take up to two minutes. After a successful upload, the system will reboot. Click Management > F/W Upload to display the screen as shown. Follow the instructions in this screen to upload firmware to your device. Figure 56 Management: F/W Upload ZyXEL G-570S v2 Users Guide 93 Chapter 8 Management Screens The following table describes the labels in this screen. Table 29 Management: F/W Upload LABEL File Path DESCRIPTION Type in the location of the file you want to upload in this field or click Browse ... to find it. Click Browse... to find the .rmt file you want to upload. Remember that you must decompress compressed (.zip) files before you can upload them. Click Upload to begin the upload process. This process may take up to two minutes. Browse... Upload

Do not turn off the device while firmware upload is in progress!

The following screen appears. Wait two minutes before logging into the device again. Figure 57 Firmware Upgrading Screen The device automatically restarts in this time causing a temporary network disconnect. In some operating systems, you may see the following icon on your desktop. Figure 58 Network Temporarily Disconnected After two minutes, log in again and check your new firmware version in the System Status screen. If the upload was not successful, the following status message displays at the bottom of the screen. Figure 59 Firmware Upload Error 94 ZyXEL G-570S v2 Users Guide CHAPTER 9 Troubleshooting This chapter offers some suggestions to solve problems you might encounter. The potential problems are divided into the following categories. Power, Hardware Connections, and LEDs ZyXEL Device Access and Login Internet Access 9.1 Power, Hardware Connections, and LEDs

The ZyXEL Device does not turn on. None of the LEDs turn on. 6 Make sure you are using the power adaptor or cord included with the ZyXEL Device. 7 Make sure the power adaptor or cord is connected to the ZyXEL Device and plugged in to an appropriate power source. Make sure the power source is turned on. 8 Disconnect and re-connect the power adaptor or cord to the ZyXEL Device. 9 If the problem continues, contact the vendor.

One of the LEDs does not behave as expected. 1 Make sure you understand the normal behavior of the LED. See Section 1.5 on page 27. 2 Check the hardware connections. See the Quick Start Guide. 3 Inspect your cables for damage. Contact the vendor to replace any damaged cables. 4 Disconnect and re-connect the power adaptor to the ZyXEL Device. 5 If the problem continues, contact the vendor. ZyXEL G-570S v2 Users Guide 95 Chapter 9 Troubleshooting 9.2 ZyXEL Device Access and Login

I forgot the IP address for the ZyXEL Device. 1 The default IP address is 192.168.1.2. 2 If this does not work, you have to reset the device to its factory defaults. See Section 1.8 on page 29.

I forgot the password. 1 The default password is 1234. 2 If this does not work, you have to reset the device to its factory defaults. See Section 1.8 on page 29.

I cannot see or access the Login screen in the web configurator. 1 Make sure you are using the correct IP address. The default IP address is 192.168.1.2. If you changed the IP address (Section 6.2 on page 52), use the new IP address. If you changed the IP address and have forgotten it, see the troubleshooting suggestions for I forgot the IP address for the ZyXEL Device. 2 Check the hardware connections, and make sure the LEDs are behaving as expected. See the Quick Start Guide. 3 Make sure your Internet browser does not block pop-up windows and has JavaScripts and Java enabled. See Appendix C on page 123. 4 Make sure your computer is in the same subnet as the ZyXEL Device. (If you know that there are routers between your computer and the ZyXEL Device, skip this step.) If there is no DHCP server on your network, make sure your computers IP address is in the same subnet as the ZyXEL Device. See Appendix B on page 107. 5 Reset the device to its factory defaults, and try to access the ZyXEL Device with the default IP address. See Section 1.8 on page 29. 6 If the problem continues, contact the network administrator or vendor.

I can see the Login screen, but I cannot log in to the ZyXEL Device. 96 ZyXEL G-570S v2 Users Guide Chapter 9 Troubleshooting 1 Make sure you have entered the user name and password correctly. The default password is 1234. This field is case-sensitive, so make sure [Caps Lock] is not on. 2 You cannot log in to the web configurator while someone is using Telnet to access the ZyXEL Device. Log out of the ZyXEL Device in the other session, or ask the person who is logged in to log out. 3 Disconnect and re-connect the power adaptor or cord to the ZyXEL Device. 4 If this does not work, you have to reset the device to its factory defaults. See Section 1.8 on page 29.

I cannot access the ZyXEL Device from the WLAN. Make sure the wireless adapter on the wireless station is working properly. Check that both the G-570S and your wireless station are using the same ESSID, channel and security settings.

I cannot ping any computer on the WLAN. Make sure the wireless adapter on the wireless station(s) is working properly. Check that both the G-570S v2 and wireless station(s) are using the same ESSID, channel and security settings.

I cannot Telnet to the ZyXEL Device. See the troubleshooting suggestions for I cannot see or access the Login screen in the web configurator. Ignore the suggestions about your browser.

I cannot use FTP to upload / download the configuration file. / I cannot use FTP to upload new firmware. See the troubleshooting suggestions for I cannot see or access the Login screen in the web configurator. Ignore the suggestions about your browser. ZyXEL G-570S v2 Users Guide 97 Chapter 9 Troubleshooting 9.3 Internet Access

I cannot access the Internet. 1 Check the hardware connections, and make sure the LEDs are behaving as expected. See the Quick Start Guide and Section 1.5 on page 27. 2 If you are trying to access the Internet wirelessly, make sure the wireless settings in the wireless client are the same as the settings in the AP. 3 Disconnect all the cables from your device, and follow the directions in the Quick Start Guide again. 4 If the problem continues, contact your ISP.

I cannot access the Internet anymore. I had access to the Internet (with the ZyXEL Device), but my Internet connection is not available anymore. 1 Check the hardware connections, and make sure the LEDs are behaving as expected. See the Quick Start Guide and Section 1.5 on page 27. 2 Disconnect and re-connect the power adaptor to the ZyXEL Device. 3 If the problem continues, contact your ISP.

The Internet connection is slow or intermittent. 1 There might be a lot of traffic on the network. Look at the LEDs, and check Section 1.5 on page 27. If the ZyXEL Device is sending or receiving a lot of information, try closing some programs that use the Internet, especially peer-to-peer applications. 2 Check the signal strength. If the signal strength is low, try moving the ZyXEL Device closer to the AP if possible, and look around to see if there are any devices that might be interfering with the wireless network (for example, microwaves, other wireless networks, and so on). 3 Disconnect and re-connect the power adaptor to the ZyXEL Device. 4 If the problem continues, contact the network administrator or vendor. 98 ZyXEL G-570S v2 Users Guide PART IV Appendices and Index Product Specifications (101) Setting up Your Computers IP Address (107) Pop-up Windows, JavaScripts and Java Permissions (123) Wireless LANs (129) Customer Support (143) Legal Information (147) Index (151) 99 100 APPENDIX A Product Specifications The following tables summarize the ZyXEL Devices hardware and firmware features. Hardware Specifications Table 30 Hardware Specifications Default IP Address 192.168.1.2 255.255.255.0 (24 bits) Default Subnet Mask 1234 Default Password Dimensions 112 mm (Wide) 106 mm (Deep) 28.5 mm (High) 203 g Weight One auto-negotiating, auto MDI/MDI-X 10/100 Mbps RJ-45 Ethernet port Ethernet Port Antenna 1 detachable dipole antenna 12VDC @ 1 Amp maximum Power Requirements 0 C ~ 50 C Operation Temperature Storage Temperature

-30 ~ 60 C 20% ~ 95% RH Operation Humidity Storage Humidity 20% ~ 95% RH Feature Specifications Table 31 Feature Specifications Protocol Support Standards Compliance Transparent bridging for unsupported network layer protocols DHCP Client DHCP relay IEEE 802.3 and 802.3u 10Base-T and 100Base-TX physical layer specification IEEE 802.11g specification compliance for wireless LAN IEEE 802.11b specification compliance for wireless LAN IEEE 802.1x security standard support Wi-Fi certificate ZyXEL G-570S v2 Users Guide 101 Appendix A Product Specifications Management Wireless Links Operating Modes Table 31 Feature Specifications (continued) Roaming IEEE 802.11g compliant IEEE 802.11b compliant IEEE 802.11f partially compliant (without re-authentication) Access Point Client Bridge Access Point and Repeater The ZyXEL Device can act as a bridge, establishing wireless links with other APs or as a repeater, establishing wireless links to APs. Up to four bridge links. Two or more repeater links are supported. It is suggested that you only use up to three repeater links. Embedded Web Configurator Command-line interface Telnet support (Password-protected telnet access to internal configuration manager). FTP//Web for firmware downloading and configuration backup and restore. Limitation of client connections (# is configurable, default: unlimited) Intra BSS Block (enable/disable) Output Power Management (4-levels) WPA and IEEE 802.1x security (EAP-TLS, EAP-TTLS, LEAP,. EAP-PEAP and Win XP PEAP included) 64/128/152-bits WEP WPA/WPA2 support based on 802.11i standard Dynamic WEP key exchange MAC address filtering through WLAN (supports up to 32 MAC address entries AES support Security Diagnostics Capabilities Built-in Diagnostic Tools for FLASH memory, RAM, Ethernet port and wireless port. Syslog Error log Trace Log Packet Log Restore Factory Defaults (reset) Button Status LEDs PWR ETHN OTIST WLAN A Distribution System (DS) is a wired connection between two or more APs, while a Wireless Distribution System (WDS) is a wireless connection. Your G-570S v2 supports WDS connections to other G-570S v2 APs. This provides a cost-effective solution for wireless network expansion. OTIST allows your ZyXEL Device to assign its SSID and security settings

(WEP or WPA-PSK) to ZyXEL wireless adapters that support OTIST and are within transmission range. The ZyXEL wireless adapters must also have OTIST enabled. Hardware Features WDS Functionality OTIST (One-Touch Intelligent Security Technology) 102 ZyXEL G-570S v2 Users Guide Appendix A Product Specifications Table 31 Feature Specifications (continued) 10/100M Auto-

negotiating Ethernet/

Fast Ethernet Interface Wi-Fi Protected Access Wi-Fi Protected Access (WPA) is a subset of the IEEE 802.11i standard. Key This auto-negotiating feature allows the ZyXEL Device to detect the speed of incoming transmissions and adjust appropriately without manual intervention. It allows data transfer of either 10 Mbps or 100 Mbps in either half-duplex or full-duplex mode depending on your Ethernet network. Ethernet port connections can be in half-duplex or full-duplex mode. Full-

duplex refers to a device's ability to send and receive simultaneously, while half-duplex indicates that traffic can flow in only one direction at a time. The Ethernet port must use the same speed or duplex mode setting as the peer Ethernet port in order to connect. The LAN interface automatically adjusts to either a crossover or straight-

through Ethernet cable. The reset button is built into the rear panel. Use this button to restart the device or restore the factory default password. The ZyXEL Device complies with the IEEE 802.11g wireless standard. IEEE 802.11g is fully compatible with the IEEE 802.11b standard. This means an IEEE 802.11b radio card can interface directly with an IEEE 802.11g access point (and vice versa) at 11 Mbps or lower depending on range. differences between WPA and WEP are user authentication and improved data encryption. WPA 2 (IEEE 802.11i) is a wireless security standard that defines stronger encryption, authentication and key management than WPA. The ZyXEL Device allows SSL connections to go through the ZyXEL Device. SSL (Secure Sockets Layer) uses a public key to encrypt data that's transmitted over an SSL connection. Both Netscape Navigator and Internet Explorer support SSL, and many Web sites use the protocol to obtain confidential user information, such as credit card numbers. By convention, URLs that require an SSL connection start with "https" instead of "http". Your ZyXEL Device checks the MAC address of the wireless station against a list of allowed or denied MAC addresses. WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless network to help keep network communications private. The ZyXEL Device supports the IEEE 802.1x standard to enhance user authentication. Use an EAP-compatible RADIUS (RFC2138, 2139 - Remote Authentication Dial In User Service) server to authenticate a limitless number of users using EAP (Extensible Authentication Protocol). EAP is an authentication protocol that supports multiple types of authentication. The embedded web configurator is an all-platform web-based utility that allows you to easily access the ZyXEL Device's management settings. Built-in message logging and packet tracing. With the wireless association list, you can see the list of the wireless stations that are currently using the ZyXEL Device to access your wired network. When the ZyXEL Device is in client mode, the wireless association list displays a list of wireless devices and networks in the area. 10/100M Auto-

crossover Ethernet/Fast Ethernet Interface Reset Button 802.11g Wireless LAN Standard WPA2 SSL Passthrough Wireless LAN MAC Address Filtering WEP Encryption IEEE 802.1x Network Security Full Network Management Logging and Tracing Wireless Association List ZyXEL G-570S v2 Users Guide 103 Appendix A Product Specifications Table 31 Feature Specifications (continued) Output Power Management Output Power Management is the ability to set the level of output power. There may be interference or difficulty with channel assignment when there is a high density of APs within a coverage area. In this case you can lower the output power of each access point, thus enabling you to place access points closer together. You may set a maximum number of wireless stations that may connect to the ZyXEL Device. This may be necessary if for example, there is interference or difficulty with channel assignment due to a high density of APs within a coverage area. Limit the Number of Client Connections Super G/11g: 108M/54M/48M/36M/24M/18M/12M/9/6 Mbps auto fallback 11b: 11Mbps/5.5Mbps/2Mbps/1Mbps auto fallback Half Duplex Direct Sequence Spread Spectrum (DSSS) Wired Equivalent Privacy (WEP) data encryption Dynamic WEP key exchange WiFi Protected Access (WPA) IEEE 802.1x 2.412~2.462GHz: North America 2.412MHz~2.484 GHz: Japan 2.412-2.472 GHz: Europe ETSI OFDM/BPSK/QPSK/CCK/PBCC/DQPSK/DBPSK 11b : 18+/-2dBm @ 11/5.5/2/1Mbps. 11g : 20+/-2dBm @ 54Mbps. 54M: -65dBm 11M: -80dBm Indoor: up to 100meters Outdoor: up to 400meters 1 external detachable 2dBi dipole antenna with R-SMA connector Wireless Specifications Table 32 Wireless Specifications Data Rate Communication Method Transmission/Emission Type Security RF frequency range Data modulation type Output Power (peak) Sensitivity Coverage Antenna Approvals Table 33 Approvals SAFETY North America European Union (CE mark) ANSI/UL-1950 3rd CSA C22.2 No. 950 3rd EN60950 (1992+A1+A2+A3+A4+A11) IEC 60950 3rd 104 ZyXEL G-570S v2 Users Guide Table 33 Approvals (continued) Appendix A Product Specifications EMI EMS ELECTROSTATIC DISCHARGE RADIO-FREQUENCY ELECTROMAGNETIC FIELD EFT/BURST SURGE CONDUCTED SUSCEPTIBILITY POWER MAGNETIC VOLTAGE DIPS/

INTERRUPTION EM FIELD FROM DIGITAL TELEPHONES LAN COMPATIBILITY FOR WIRELESS PC CARD North America European Union (CE mark) European Union (CE mark) FCC Part 15 Class B EN55022 Class B EN61000-3-2 EN61000-3-3 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-8 EN61000-4-11 ENV50204 SmartBit FCC Part15C, Sec15.247 ETS300 328 ETS300 826 CE mark Power Adaptor Specifications Table 34 Power Adaptor Specifications AUSTRALIAN PLUG STANDARDS AC Power Adapter Model Input Power Output Power Power Consumption Safety Standards EUROPEAN PLUG STANDARDS AC Power Adapter Model Input Power Output Power Power Consumption Safety Standards AD-121AE 240 Volts AC 50Hz 12 Volts DC 5% 1 Amp 12 Watts C-Tick AD-121AB 230 Volts AC 50Hz 12 Volts DC 5%, 1 Amp 12 Watts CE mark, EN60950 (2001) ZyXEL G-570S v2 Users Guide 105 Appendix A Product Specifications Table 34 Power Adaptor Specifications (continued) NORTH AMERICAN PLUG STANDARDS AC Power Adapter Model Input Power Output Power Power Consumption Safety Standards UK PLUG STANDARDS AC Power Adapter Model Input Power Output Power Power Consumption Safety Standards AD-121A 120 Volts AC 60Hz 12 Volts DC 5%, 1 Amp 12 Watts UL AD-121AD 240 Volts AC 50Hz 12 Volts DC 5% 1 Amp 12 Watts CE mark, EN60950 (2001) 106 ZyXEL G-570S v2 Users Guide APPENDIX B Setting up Your Computers IP Address All computers must have a 10M or 100M Ethernet adapter card and TCP/IP installed. Windows 95/98/Me/NT/2000/XP, Macintosh OS 7 and later operating systems and all versions of UNIX/LINUX include the software components you need to install and use TCP/IP on your computer. Windows 3.1 requires the purchase of a third-party TCP/IP application package. TCP/IP should already be installed on computers using Windows NT/2000/XP, Macintosh OS 7 and later operating systems. After the appropriate TCP/IP components are installed, configure the TCP/IP settings in order to "communicate" with your network. If you manually assign IP information instead of using dynamic assignment, make sure that your computers have IP addresses that place them in the same subnet as the ZyXEL Devices LAN port. Windows 95/98/Me Click Start, Settings, Control Panel and double-click the Network icon to open the Network window. ZyXEL G-570S v2 Users Guide 107 Appendix B Setting up Your Computers IP Address Figure 60 WIndows 95/98/Me: Network: Configuration Installing Components The Network window Configuration tab displays a list of installed components. You need a network adapter, the TCP/IP protocol and Client for Microsoft Networks. If you need the adapter:

1 In the Network window, click Add. 2 Select Adapter and then click Add. 3 Select the manufacturer and model of your network adapter and then click OK. If you need TCP/IP:

1 In the Network window, click Add. 2 Select Protocol and then click Add. 3 Select Microsoft from the list of manufacturers. 4 Select TCP/IP from the list of network protocols and then click OK. If you need Client for Microsoft Networks:

1 Click Add. 2 Select Client and then click Add. 3 Select Microsoft from the list of manufacturers. 4 Select Client for Microsoft Networks from the list of network clients and then click OK. 5 Restart your computer so the changes you made take effect. 108 ZyXEL G-570S v2 Users Guide Configuring Appendix B Setting up Your Computers IP Address 1 In the Network window Configuration tab, select your network adapter's TCP/IP entry and click Properties 2 Click the IP Address tab. If your IP address is dynamic, select Obtain an IP address automatically. If you have a static IP address, select Specify an IP address and type your information into the IP Address and Subnet Mask fields. Figure 61 Windows 95/98/Me: TCP/IP Properties: IP Address 3 Click the DNS Configuration tab. If you do not know your DNS information, select Disable DNS. If you know your DNS information, select Enable DNS and type the information in the fields below (you may not need to fill them all in). ZyXEL G-570S v2 Users Guide 109 Appendix B Setting up Your Computers IP Address Figure 62 Windows 95/98/Me: TCP/IP Properties: DNS Configuration 4 Click the Gateway tab. If you do not know your gateways IP address, remove previously installed gateways. If you have a gateway IP address, type it in the New gateway field and click Add. 5 Click OK to save and close the TCP/IP Properties window. 6 Click OK to close the Network window. Insert the Windows CD if prompted. 7 Turn on your ZyXEL Device and restart your computer when prompted. Verifying Settings 1 Click Start and then Run. 2 In the Run window, type "winipcfg" and then click OK to open the IP Configuration 3 Select your network adapter. You should see your computer's IP address, subnet mask window. and default gateway. Windows 2000/NT/XP The following example figures use the default Windows XP GUI theme. 1 Click start (Start in Windows 2000/NT), Settings, Control Panel. 110 ZyXEL G-570S v2 Users Guide Appendix B Setting up Your Computers IP Address Figure 63 Windows XP: Start Menu 2 In the Control Panel, double-click Network Connections (Network and Dial-up Connections in Windows 2000/NT). Figure 64 Windows XP: Control Panel 3 Right-click Local Area Connection and then click Properties. ZyXEL G-570S v2 Users Guide 111 Appendix B Setting up Your Computers IP Address Figure 65 Windows XP: Control Panel: Network Connections: Properties 4 Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and then click Properties. Figure 66 Windows XP: Local Area Connection Properties 5 The Internet Protocol TCP/IP Properties window opens (the General tab in Windows XP). If you have a dynamic IP address click Obtain an IP address automatically. If you have a static IP address click Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields. Click Advanced. 112 ZyXEL G-570S v2 Users Guide Appendix B Setting up Your Computers IP Address Figure 67 Windows XP: Internet Protocol (TCP/IP) Properties 6 If you do not know your gateway's IP address, remove any previously installed gateways in the IP Settings tab and click OK. Do one or more of the following if you want to configure additional IP addresses:

In the IP Settings tab, in IP addresses, click Add. In TCP/IP Address, type an IP address in IP address and a subnet mask in Subnet mask, and then click Add. Repeat the above two steps for each IP address you want to add. Configure additional default gateways in the IP Settings tab by clicking Add in Default gateways. In TCP/IP Gateway Address, type the IP address of the default gateway in Gateway. To manually configure a default metric (the number of transmission hops), clear the Automatic metric check box and type a metric in Metric. Click Add. Repeat the previous three steps for each default gateway you want to add. Click OK when finished. ZyXEL G-570S v2 Users Guide 113 Appendix B Setting up Your Computers IP Address Figure 68 Windows XP: Advanced TCP/IP Properties 7 In the Internet Protocol TCP/IP Properties window (the General tab in Windows XP):

Click Obtain DNS server address automatically if you do not know your DNS server IP address(es). If you know your DNS server IP address(es), click Use the following DNS server addresses, and type them in the Preferred DNS server and Alternate DNS server fields. If you have previously configured DNS servers, click Advanced and then the DNS tab to order them. 114 ZyXEL G-570S v2 Users Guide Appendix B Setting up Your Computers IP Address Figure 69 Windows XP: Internet Protocol (TCP/IP) Properties 8 Click OK to close the Internet Protocol (TCP/IP) Properties window. 9 Click Close (OK in Windows 2000/NT) to close the Local Area Connection 10 Close the Network Connections window (Network and Dial-up Connections in Properties window. Windows 2000/NT). 11 Turn on your ZyXEL Device and restart your computer (if prompted). Verifying Settings 1 Click Start, All Programs, Accessories and then Command Prompt. 2 In the Command Prompt window, type "ipconfig" and then press [ENTER]. You can also open Network Connections, right-click a network connection, click Status and then click the Support tab. Macintosh OS 8/9 1 Click the Apple menu, Control Panel and double-click TCP/IP to open the TCP/IP Control Panel. ZyXEL G-570S v2 Users Guide 115 Appendix B Setting up Your Computers IP Address Figure 70 Macintosh OS 8/9: Apple Menu 2 Select Ethernet built-in from the Connect via list. Figure 71 Macintosh OS 8/9: TCP/IP 3 For dynamically assigned settings, select Using DHCP Server from the Configure: list. 4 For statically assigned settings, do the following:

From the Configure box, select Manually. 116 ZyXEL G-570S v2 Users Guide Appendix B Setting up Your Computers IP Address Type your IP address in the IP Address box. Type your subnet mask in the Subnet mask box. Type the IP address of your ZyXEL Device in the Router address box. 5 Close the TCP/IP Control Panel. 6 Click Save if prompted, to save changes to your configuration. 7 Turn on your ZyXEL Device and restart your computer (if prompted). Verifying Settings Check your TCP/IP properties in the TCP/IP Control Panel window. Macintosh OS X 1 Click the Apple menu, and click System Preferences to open the System Preferences window. Figure 72 Macintosh OS X: Apple Menu 2 Click Network in the icon bar. Select Automatic from the Location list. Select Built-in Ethernet from the Show list. Click the TCP/IP tab. 3 For dynamically assigned settings, select Using DHCP from the Configure list. ZyXEL G-570S v2 Users Guide 117 Appendix B Setting up Your Computers IP Address Figure 73 Macintosh OS X: Network 4 For statically assigned settings, do the following:

From the Configure box, select Manually. Type your IP address in the IP Address box. Type your subnet mask in the Subnet mask box. Type the IP address of your ZyXEL Device in the Router address box. 5 Click Apply Now and close the window. 6 Turn on your ZyXEL Device and restart your computer (if prompted). Verifying Settings Check your TCP/IP properties in the Network window. Linux 118 This section shows you how to configure your computers TCP/IP settings in Red Hat Linux 9.0. Procedure, screens and file location may vary depending on your Linux distribution and release version. ZyXEL G-570S v2 Users Guide Appendix B Setting up Your Computers IP Address

Make sure you are logged in as the root administrator. Using the K Desktop Environment (KDE) Follow the steps below to configure your computer IP address using the KDE. 1 Click the Red Hat button (located on the bottom left corner), select System Setting and click Network. Figure 74 Red Hat 9.0: KDE: Network Configuration: Devices 2 Double-click on the profile of the network card you wish to configure. The Ethernet Device General screen displays as shown. Figure 75 Red Hat 9.0: KDE: Ethernet Device: General ZyXEL G-570S v2 Users Guide 119 Appendix B Setting up Your Computers IP Address If you have a dynamic IP address, click Automatically obtain IP address settings with and select dhcp from the drop down list. If you have a static IP address, click Statically set IP Addresses and fill in the Address, Subnet mask, and Default Gateway Address fields. 3 Click OK to save the changes and close the Ethernet Device General screen. 4 If you know your DNS server IP address(es), click the DNS tab in the Network Configuration screen. Enter the DNS server information in the fields provided. Figure 76 Red Hat 9.0: KDE: Network Configuration: DNS 5 Click the Devices tab. 6 Click the Activate button to apply the changes. The following screen displays. Click Yes to save the changes in all screens. Figure 77 Red Hat 9.0: KDE: Network Configuration: Activate 7 After the network card restart process is complete, make sure the Status is Active in the Network Configuration screen. Using Configuration Files Follow the steps below to edit the network configuration files and set your computer IP address. 1 Assuming that you have only one network card on the computer, locate the ifconfig-

eth0 configuration file (where eth0 is the name of the Ethernet card). Open the configuration file with any plain text editor. If you have a dynamic IP address, enter dhcp in the BOOTPROTO= field. The following figure shows an example. 120 ZyXEL G-570S v2 Users Guide Appendix B Setting up Your Computers IP Address Figure 78 Red Hat 9.0: Dynamic IP Address Setting in ifconfig-eth0 DEVICE=eth0 ONBOOT=yes BOOTPROTO=dhcp USERCTL=no PEERDNS=yes TYPE=Ethernet If you have a static IP address, enter static in the BOOTPROTO= field. Type IPADDR= followed by the IP address (in dotted decimal notation) and type NETMASK=

followed by the subnet mask. The following example shows an example where the static IP address is 192.168.1.10 and the subnet mask is 255.255.255.0. Figure 79 Red Hat 9.0: Static IP Address Setting in ifconfig-eth0 DEVICE=eth0 ONBOOT=yes BOOTPROTO=static IPADDR=192.168.1.10 NETMASK=255.255.255.0 USERCTL=no PEERDNS=yes TYPE=Ethernet 2 If you know your DNS server IP address(es), enter the DNS server information in the resolv.conf file in the /etc directory. The following figure shows an example where two DNS server IP addresses are specified. Figure 80 Red Hat 9.0: DNS Settings in resolv.conf nameserver 172.23.5.1 nameserver 172.23.5.2 3 After you edit and save the configuration files, you must restart the network card. Enter

./network restart in the /etc/rc.d/init.d directory. The following figure shows an example. Figure 81 Red Hat 9.0: Restart Ethernet Card

[root@localhost init.d]# network restart Shutting down interface eth0: [OK]

Shutting down loopback interface: [OK]

Setting network parameters: [OK]

Bringing up loopback interface: [OK]

Bringing up interface eth0: [OK]

ZyXEL G-570S v2 Users Guide 121 Appendix B Setting up Your Computers IP Address Verifying Settings Enter ifconfig in a terminal screen to check your TCP/IP properties. Figure 82 Red Hat 9.0: Checking TCP/IP Properties

[root@localhost]# ifconfig eth0 Link encap:Ethernet HWaddr 00:50:BA:72:5B:44 inet addr:172.23.19.129 Bcast:172.23.19.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:717 errors:0 dropped:0 overruns:0 frame:0 TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:730412 (713.2 Kb) TX bytes:1570 (1.5 Kb) Interrupt:10 Base address:0x1000

[root@localhost]#

122 ZyXEL G-570S v2 Users Guide APPENDIX C Pop-up Windows, JavaScripts and Java Permissions In order to use the web configurator you need to allow:

Web browser pop-up windows from your device. JavaScripts (enabled by default). Java permissions (enabled by default).

Internet Explorer 6 screens are used here. Screens for other Internet Explorer versions may vary. Internet Explorer Pop-up Blockers You may have to disable pop-up blocking to log into your device. Either disable pop-up blocking (enabled by default in Windows XP SP (Service Pack) 2) or allow pop-up blocking and create an exception for your devices IP address. Disable pop-up Blockers 1 In Internet Explorer, select Tools, Pop-up Blocker and then select Turn Off Pop-up Blocker. Figure 83 Pop-up Blocker You can also check if pop-up blocking is disabled in the Pop-up Blocker section in the Privacy tab. 1 In Internet Explorer, select Tools, Internet Options, Privacy. ZyXEL G-570S v2 Users Guide 123 Appendix C Pop-up Windows, JavaScripts and Java Permissions 2 Clear the Block pop-ups check box in the Pop-up Blocker section of the screen. This disables any web pop-up blockers you may have enabled. Figure 84 Internet Options: Privacy 3 Click Apply to save this setting. Enable pop-up Blockers with Exceptions Alternatively, if you only want to allow pop-up windows from your device, see the following steps. 1 In Internet Explorer, select Tools, Internet Options and then the Privacy tab. 2 Select Settingsto open the Pop-up Blocker Settings screen. 124 ZyXEL G-570S v2 Users Guide Appendix C Pop-up Windows, JavaScripts and Java Permissions Figure 85 Internet Options: Privacy 3 Type the IP address of your device (the web page that you do not want to have blocked) with the prefix http://. For example, http://192.168.167.1. 4 Click Add to move the IP address to the list of Allowed sites. Figure 86 Pop-up Blocker Settings ZyXEL G-570S v2 Users Guide 125 Appendix C Pop-up Windows, JavaScripts and Java Permissions 5 Click Close to return to the Privacy screen. 6 Click Apply to save this setting. JavaScripts If pages of the web configurator do not display properly in Internet Explorer, check that JavaScripts are allowed. 1 In Internet Explorer, click Tools, Internet Options and then the Security tab. Figure 87 Internet Options: Security 2 Click the Custom Level... button. 3 Scroll down to Scripting. 4 Under Active scripting make sure that Enable is selected (the default). 5 Under Scripting of Java applets make sure that Enable is selected (the default). 6 Click OK to close the window. 126 ZyXEL G-570S v2 Users Guide Appendix C Pop-up Windows, JavaScripts and Java Permissions Figure 88 Security Settings - Java Scripting Java Permissions 1 From Internet Explorer, click Tools, Internet Options and then the Security tab. 2 Click the Custom Level... button. 3 Scroll down to Microsoft VM. 4 Under Java permissions make sure that a safety level is selected. 5 Click OK to close the window. Figure 89 Security Settings - Java ZyXEL G-570S v2 Users Guide 127 Appendix C Pop-up Windows, JavaScripts and Java Permissions JAVA (Sun) 1 From Internet Explorer, click Tools, Internet Options and then the Advanced tab. 2 Make sure that Use Java 2 for <applet> under Java (Sun) is selected. 3 Click OK to close the window. Figure 90 Java (Sun) 128 ZyXEL G-570S v2 Users Guide APPENDIX D Wireless LANs Wireless LAN Topologies This section discusses ad-hoc and infrastructure wireless LAN topologies. Ad-hoc Wireless LAN Configuration The simplest WLAN configuration is an independent (Ad-hoc) WLAN that connects a set of computers with wireless adapters (A, B, C). Any time two or more wireless adapters are within range of each other, they can set up an independent network, which is commonly referred to as an ad-hoc network or Independent Basic Service Set (IBSS). The following diagram shows an example of notebook computers using wireless adapters to form an ad-hoc wireless LAN. Figure 91 Peer-to-Peer Communication in an Ad-hoc Network BSS A Basic Service Set (BSS) exists when all communications between wireless clients or between a wireless client and a wired network client go through one access point (AP). Intra-BSS traffic is traffic between wireless clients in the BSS. When Intra-BSS is enabled, wireless client A and B can access the wired network and communicate with each other. When Intra-BSS is disabled, wireless client A and B can still access the wired network but cannot communicate with each other. ZyXEL G-570S v2 Users Guide 129 Appendix D Wireless LANs Figure 92 Basic Service Set ESS An Extended Service Set (ESS) consists of a series of overlapping BSSs, each containing an access point, with each access point connected together by a wired network. This wired connection between APs is called a Distribution System (DS). This type of wireless LAN topology is called an Infrastructure WLAN. The Access Points not only provide communication with the wired network but also mediate wireless network traffic in the immediate neighborhood. An ESSID (ESS IDentification) uniquely identifies each ESS. All access points and their associated wireless clients within the same ESS must have the same ESSID in order to communicate. 130 ZyXEL G-570S v2 Users Guide Figure 93 Infrastructure WLAN Appendix D Wireless LANs Channel A channel is the radio frequency(ies) used by IEEE 802.11a/b/g wireless devices. Channels available depend on your geographical area. You may have a choice of channels (for your region) so you should use a different channel than an adjacent AP (access point) to reduce interference. Interference occurs when radio signals from different access points overlap causing interference and degrading performance. Adjacent channels partially overlap however. To avoid interference due to overlap, your AP should be on a channel at least five channels away from a channel that an adjacent AP is using. For example, if your region has 11 channels and an adjacent AP is using channel 1, then you need to select a channel between 6 or 11. RTS/CTS A hidden node occurs when two stations are within range of the same access point, but are not within range of each other. The following figure illustrates a hidden node. Both stations (STA) are within range of the access point (AP) or wireless gateway, but out-of-range of each other, so they cannot "hear" each other, that is they do not know if the channel is currently being used. Therefore, they are considered hidden from each other. ZyXEL G-570S v2 Users Guide 131 Appendix D Wireless LANs Figure 94 RTS/CTS When station A sends data to the AP, it might not know that the station B is already using the channel. If these two stations send data at the same time, collisions may occur when both sets of data arrive at the AP at the same time, resulting in a loss of messages for both stations. RTS/CTS is designed to prevent collisions due to hidden nodes. An RTS/CTS defines the biggest size data frame you can send before an RTS (Request To Send)/CTS (Clear to Send) handshake is invoked. When a data frame exceeds the RTS/CTS value you set (between 0 to 2432 bytes), the station that wants to transmit this frame must first send an RTS (Request To Send) message to the AP for permission to send it. The AP then responds with a CTS (Clear to Send) message to all other stations within its range to notify them to defer their transmission. It also reserves and confirms with the requesting station the time frame for the requested transmission. Stations can send frames smaller than the specified RTS/CTS directly to the AP without the RTS (Request To Send)/CTS (Clear to Send) handshake. You should only configure RTS/CTS if the possibility of hidden nodes exists on your network and the "cost" of resending large frames is more than the extra network overhead involved in the RTS (Request To Send)/CTS (Clear to Send) handshake. If the RTS/CTS value is greater than the Fragmentation Threshold value (see next), then the RTS (Request To Send)/CTS (Clear to Send) handshake will never occur as data frames will be fragmented before they reach RTS/CTS size.

Enabling the RTS Threshold causes redundant network overhead that could negatively affect the throughput performance instead of providing a remedy. Fragmentation Threshold A Fragmentation Threshold is the maximum data fragment size (between 256 and 2432 bytes) that can be sent in the wireless network before the AP will fragment the packet into smaller data frames. A large Fragmentation Threshold is recommended for networks not prone to interference while you should set a smaller threshold for busy networks or networks that are prone to interference. 132 ZyXEL G-570S v2 Users Guide Appendix D Wireless LANs If the Fragmentation Threshold value is smaller than the RTS/CTS value (see previously) you set then the RTS (Request To Send)/CTS (Clear to Send) handshake will never occur as data frames will be fragmented before they reach RTS/CTS size. Preamble Type Preamble is used to signal that data is coming to the receiver. Short and Long refer to the length of the synchronization field in a packet. Short preamble increases performance as less time sending preamble means more time for sending data. All IEEE 802.11b/g compliant wireless adapters support long preamble, but not all support short preamble. Select Long preamble if you are unsure what preamble mode the wireless adapters support, and to provide more reliable communications in busy wireless networks. Select Short preamble if you are sure the wireless adapters support it, and to provide more efficient communications. Select Dynamic to have the AP automatically use short preamble when wireless adapters support it, otherwise the AP uses long preamble.

The AP and the wireless adapters MUST use the same preamble mode in order to communicate. IEEE 802.11g Wireless LAN IEEE 802.11g is fully compatible with the IEEE 802.11b standard. This means an IEEE 802.11b adapter can interface directly with an IEEE 802.11g access point (and vice versa) at 11 Mbps or lower depending on range. IEEE 802.11g has several intermediate rate steps between the maximum and minimum data rates. The IEEE 802.11g data rate and modulation are as follows:

Table 35 IEEE 802.11g DATA RATE (MBPS) MODULATION 1 2 5.5 / 11 6/9/12/18/24/36/48/54 OFDM (Orthogonal Frequency Division Multiplexing) DBPSK (Differential Binary Phase Shift Keyed) DQPSK (Differential Quadrature Phase Shift Keying) CCK (Complementary Code Keying) Wireless Security Overview Wireless security is vital to your network to protect wireless communication between wireless clients, access points and the wired network. ZyXEL G-570S v2 Users Guide 133 Appendix D Wireless LANs Wireless security methods available on the ZyXEL Device are data encryption, wireless client authentication, restricting access by device MAC address and hiding the ZyXEL Device identity. The following figure shows the relative effectiveness of these wireless security methods available on your ZyXEL Device. Table 36 Wireless Security Levels SECURITY LEVEL Least Secure SECURITY TYPE Unique SSID (Default) Unique SSID with Hide SSID Enabled MAC Address Filtering WEP Encryption IEEE802.1x EAP with RADIUS Server Authentication Wi-Fi Protected Access (WPA) WPA2 Most Secure

You must enable the same wireless security settings on the ZyXEL Device and on all wireless clients that you want to associate with it. IEEE 802.1x In June 2001, the IEEE 802.1x standard was designed to extend the features of IEEE 802.11 to support extended authentication as well as providing additional accounting and control features. It is supported by Windows XP and a number of network devices. Some advantages of IEEE 802.1x are:

User based identification that allows for roaming. Support for RADIUS (Remote Authentication Dial In User Service, RFC 2138, 2139) for centralized user profile and accounting management on a network RADIUS server. Support for EAP (Extensible Authentication Protocol, RFC 2486) that allows additional authentication methods to be deployed with no changes to the access point or the wireless clients. RADIUS RADIUS is based on a client-server model that supports authentication, authorization and accounting. The access point is the client and the server is the RADIUS server. The RADIUS server handles the following tasks:

Authentication Determines the identity of the users. Authorization 134 ZyXEL G-570S v2 Users Guide Appendix D Wireless LANs Determines the network services available to authenticated users once they are connected to the network. Accounting Keeps track of the clients network activity. RADIUS is a simple package exchange in which your AP acts as a message relay between the wireless client and the network RADIUS server. Types of RADIUS Messages The following types of RADIUS messages are exchanged between the access point and the RADIUS server for user authentication:

Access-Request Sent by an access point requesting authentication. Access-Reject Sent by a RADIUS server rejecting access. Access-Accept Sent by a RADIUS server allowing access. Access-Challenge Sent by a RADIUS server requesting more information in order to allow access. The access point sends a proper response from the user and then sends another Access-Request message. The following types of RADIUS messages are exchanged between the access point and the RADIUS server for user accounting:

Accounting-Request Sent by the access point requesting accounting. Accounting-Response Sent by the RADIUS server to indicate that it has started or stopped accounting. In order to ensure network security, the access point and the RADIUS server use a shared secret key, which is a password, they both know. The key is not sent over the network. In addition to the shared key, password information exchanged is also encrypted to protect the network from unauthorized access. Types of EAP Authentication This section discusses some popular authentication types: EAP-MD5, EAP-TLS, EAP-TTLS, PEAP and LEAP. Your wireless LAN device may not support all authentication types. EAP (Extensible Authentication Protocol) is an authentication protocol that runs on top of the IEEE 802.1x transport mechanism in order to support multiple types of user authentication. By using EAP to interact with an EAP-compatible RADIUS server, an access point helps a wireless station and a RADIUS server perform authentication. The type of authentication you use depends on the RADIUS server and an intermediary AP(s) that supports IEEE 802.1x. ZyXEL G-570S v2 Users Guide 135 Appendix D Wireless LANs For EAP-TLS authentication type, you must first have a wired connection to the network and obtain the certificate(s) from a certificate authority (CA). A certificate (also called digital IDs) can be used to authenticate users and a CA issues certificates and guarantees the identity of each certificate owner. EAP-MD5 (Message-Digest Algorithm 5) MD5 authentication is the simplest one-way authentication method. The authentication server sends a challenge to the wireless client. The wireless client proves that it knows the password by encrypting the password with the challenge and sends back the information. Password is not sent in plain text. However, MD5 authentication has some weaknesses. Since the authentication server needs to get the plaintext passwords, the passwords must be stored. Thus someone other than the authentication server may access the password file. In addition, it is possible to impersonate an authentication server as MD5 authentication method does not perform mutual authentication. Finally, MD5 authentication method does not support data encryption with dynamic session key. You must configure WEP encryption keys for data encryption. EAP-TLS (Transport Layer Security) With EAP-TLS, digital certifications are needed by both the server and the wireless clients for mutual authentication. The server presents a certificate to the client. After validating the identity of the server, the client sends a different certificate to the server. The exchange of certificates is done in the open before a secured tunnel is created. This makes user identity vulnerable to passive attacks. A digital certificate is an electronic ID card that authenticates the senders identity. However, to implement EAP-TLS, you need a Certificate Authority (CA) to handle certificates, which imposes a management overhead. EAP-TTLS (Tunneled Transport Layer Service) EAP-TTLS is an extension of the EAP-TLS authentication that uses certificates for only the server-side authentications to establish a secure connection. Client authentication is then done by sending username and password through the secure connection, thus client identity is protected. For client authentication, EAP-TTLS supports EAP methods and legacy authentication methods such as PAP, CHAP, MS-CHAP and MS-CHAP v2. PEAP (Protected EAP) Like EAP-TTLS, server-side certificate authentication is used to establish a secure connection, then use simple username and password methods through the secured connection to authenticate the clients, thus hiding client identity. However, PEAP only supports EAP methods, such as EAP-MD5, EAP-MSCHAPv2 and EAP-GTC (EAP-Generic Token Card), for client authentication. EAP-GTC is implemented only by Cisco. LEAP 136 LEAP (Lightweight Extensible Authentication Protocol) is a Cisco implementation of IEEE 802.1x. ZyXEL G-570S v2 Users Guide Appendix D Wireless LANs Dynamic WEP Key Exchange The AP maps a unique key that is generated with the RADIUS server. This key expires when the wireless connection times out, disconnects or reauthentication times out. A new WEP key is generated each time reauthentication is performed. If this feature is enabled, it is not necessary to configure a default encryption key in the Wireless screen. You may still configure and store keys here, but they will not be used while Dynamic WEP is enabled.

EAP-MD5 cannot be used with Dynamic WEP Key Exchange For added security, certificate-based authentications (EAP-TLS, EAP-TTLS and PEAP) use dynamic keys for data encryption. They are often deployed in corporate environments, but for public deployment, a simple user name and password pair is more practical. The following table is a comparison of the features of authentication types. Table 37 Comparison of EAP Authentication Types EAP-TLS Yes Yes Yes Yes Strong Hard No Mutual Authentication Certificate Client Certificate Server Dynamic Key Exchange Credential Integrity Deployment Difficulty Client Identity Protection EAP-TTLS Yes Optional Yes Yes Strong Moderate Yes EAP-MD5 No No No No None Easy No LEAP Yes No No Yes Moderate Moderate No PEAP Yes Optional Yes Yes Strong Moderate Yes WPA and WPA2 Wi-Fi Protected Access (WPA) is a subset of the IEEE 802.11i standard. WPA2 (IEEE 802.11i) is a wireless security standard that defines stronger encryption, authentication and key management than WPA. Key differences between WPA or WPA2 and WEP are improved data encryption and user authentication. If both an AP and the wireless clients support WPA2 and you have an external RADIUS server, use WPA2 for stronger data encryption. If you don't have an external RADIUS server, you should use WPA2-PSK (WPA2-Pre-Shared Key) that only requires a single (identical) password entered into each access point, wireless gateway and wireless client. As long as the passwords match, a wireless client will be granted access to a WLAN. If the AP or the wireless clients do not support WPA2, just use WPA or WPA-PSK depending on whether you have an external RADIUS server or not. Select WEP only when the AP and/or wireless clients do not support WPA or WPA2. WEP is less secure than WPA or WPA2. ZyXEL G-570S v2 Users Guide 137 Appendix D Wireless LANs Encryption Both WPA and WPA2 improve data encryption by using Temporal Key Integrity Protocol

(TKIP), Message Integrity Check (MIC) and IEEE 802.1x. WPA and WPA2 use Advanced Encryption Standard (AES) in the Counter mode with Cipher block chaining Message authentication code Protocol (CCMP) to offer stronger encryption than TKIP. TKIP uses 128-bit keys that are dynamically generated and distributed by the authentication server. AES (Advanced Encryption Standard) is a block cipher that uses a 256-bit mathematical algorithm called Rijndael. They both include a per-packet key mixing function, a Message Integrity Check (MIC) named Michael, an extended initialization vector (IV) with sequencing rules, and a re-keying mechanism. WPA and WPA2 regularly change and rotate the encryption keys so that the same encryption key is never used twice. The RADIUS server distributes a Pairwise Master Key (PMK) key to the AP that then sets up a key hierarchy and management system, using the PMK to dynamically generate unique data encryption keys to encrypt every data packet that is wirelessly communicated between the AP and the wireless clients. This all happens in the background automatically. The Message Integrity Check (MIC) is designed to prevent an attacker from capturing data packets, altering them and resending them. The MIC provides a strong mathematical function in which the receiver and the transmitter each compute and then compare the MIC. If they do not match, it is assumed that the data has been tampered with and the packet is dropped. By generating unique data encryption keys for every data packet and by creating an integrity checking mechanism (MIC), with TKIP and AES it is more difficult to decrypt data on a Wi-Fi network than WEP and difficult for an intruder to break into the network. The encryption mechanisms used for WPA(2) and WPA(2)-PSK are the same. The only difference between the two is that WPA(2)-PSK uses a simple common password, instead of user-specific credentials. The common-password approach makes WPA(2)-PSK susceptible to brute-force password-guessing attacks but its still an improvement over WEP as it employs a consistent, single, alphanumeric password to derive a PMK which is used to generate unique temporal encryption keys. This prevent all wireless devices sharing the same encryption keys.

(a weakness of WEP) User Authentication WPA and WPA2 apply IEEE 802.1x and Extensible Authentication Protocol (EAP) to authenticate wireless clients using an external RADIUS database. WPA2 reduces the number of key exchange messages from six to four (CCMP 4-way handshake) and shortens the time required to connect to a network. Other WPA2 authentication features that are different from WPA include key caching and pre-authentication. These two features are optional and may not be supported in all wireless devices. Key caching allows a wireless client to store the PMK it derived through a successful authentication with an AP. The wireless client uses the PMK when it tries to connect to the same AP and does not need to go with the authentication process again. Pre-authentication enables fast roaming by allowing the wireless client (already connecting to an AP) to perform IEEE 802.1x authentication with another AP before connecting to it. 138 ZyXEL G-570S v2 Users Guide Appendix D Wireless LANs Wireless Client WPA Supplicants A wireless client supplicant is the software that runs on an operating system instructing the wireless client how to use WPA. At the time of writing, the most widely available supplicant is the WPA patch for Windows XP, Funk Software's Odyssey client. The Windows XP patch is a free download that adds WPA capability to Windows XP's built-in

"Zero Configuration" wireless client. However, you must run Windows XP to use it. WPA(2) with RADIUS Application Example You need the IP address of the RADIUS server, its port number (default is 1812), and the RADIUS shared secret. A WPA(2) application example with an external RADIUS server looks as follows. "A" is the RADIUS server. "DS" is the distribution system. 1 The AP passes the wireless client's authentication request to the RADIUS server. 2 The RADIUS server then checks the user's identification against its database and grants or denies network access accordingly. 3 The RADIUS server distributes a Pairwise Master Key (PMK) key to the AP that then sets up a key hierarchy and management system, using the pair-wise key to dynamically generate unique data encryption keys to encrypt every data packet that is wirelessly communicated between the AP and the wireless clients. Figure 95 WPA(2) with RADIUS Application Example WPA(2)-PSK Application Example A WPA(2)-PSK application looks as follows. 1 First enter identical passwords into the AP and all wireless clients. The Pre-Shared Key

(PSK) must consist of between 8 and 63 ASCII characters or 64 hexadecimal characters

(including spaces and symbols). 2 The AP checks each wireless client's password and (only) allows it to join the network if 3 The AP and wireless clients use the pre-shared key to generate a common PMK the password matches.

(Pairwise Master Key). ZyXEL G-570S v2 Users Guide 139 Appendix D Wireless LANs 4 The AP and wireless clients use the TKIP or AES encryption process to encrypt data exchanged between them. Figure 96 WPA(2)-PSK Authentication Security Parameters Summary Refer to this table to see what other security parameters you should configure for each Authentication Method/ key management protocol type. MAC address filters are not dependent on how you configure these security features. Table 38 Wireless Security Relational Matrix AUTHENTICATION METHOD/ KEY MANAGEMENT PROTOCOL Open ENTER MANUAL KEY ENCRYPTIO N METHOD IEEE 802.1X None No Open Shared WPA WPA-PSK WPA2 WPA2-PSK WEP WEP TKIP/AES TKIP/AES TKIP/AES TKIP/AES No Yes Yes No Yes Yes No Yes No Yes Disable Enable without Dynamic WEP Key Enable with Dynamic WEP Key Enable without Dynamic WEP Key Disable Enable with Dynamic WEP Key Enable without Dynamic WEP Key Disable Enable Disable Enable Disable Antenna Overview An antenna couples RF signals onto air. A transmitter within a wireless device sends an RF signal to the antenna, which propagates the signal through the air. The antenna also operates in reverse by capturing RF signals from the air. 140 ZyXEL G-570S v2 Users Guide Positioning the antennas properly increases the range and coverage area of a wireless LAN. Appendix D Wireless LANs Antenna Characteristics Frequency An antenna in the frequency of 2.4GHz (IEEE 802.11b) or 5GHz(IEEE 802.11a) is needed to communicate efficiently in a wireless LAN. Radiation Pattern A radiation pattern is a diagram that allows you to visualize the shape of the antennas coverage area. Antenna Gain Antenna gain, measured in dB (decibel), is the increase in coverage within the RF beam width. Higher antenna gain improves the range of the signal for better communications. For an indoor site, each 1 dB increase in antenna gain results in a range increase of approximately 2.5%. For an unobstructed outdoor site, each 1dB increase in gain results in a range increase of approximately 5%. Actual results may vary depending on the network environment. Antenna gain is sometimes specified in dBi, which is how much the antenna increases the signal power compared to using an isotropic antenna. An isotropic antenna is a theoretical perfect antenna that sends out radio signals equally well in all directions. dBi represents the true gain that the antenna provides. Types of Antennas for WLAN There are two types of antennas used for wireless LAN applications. Omni-directional antennas send the RF signal out in all directions on a horizontal plane. The coverage area is torus-shaped (like a donut) which makes these antennas ideal for a room environment. With a wide coverage area, it is possible to make circular overlapping coverage areas with multiple access points. Directional antennas concentrate the RF signal in a beam, like a flashlight does with the light from its bulb. The angle of the beam determines the width of the coverage pattern. Angles typically range from 20 degrees (very directional) to 120 degrees (less directional). Directional antennas are ideal for hallways and outdoor point-to-point applications. Positioning Antennas In general, antennas should be mounted as high as practically possible and free of obstructions. In point-topoint application, position both antennas at the same height and in a direct line of sight to each other to attain the best performance. ZyXEL G-570S v2 Users Guide 141 Appendix D Wireless LANs For omni-directional antennas mounted on a table, desk, and so on, point the antenna up. For omni-directional antennas mounted on a wall or ceiling, point the antenna down. For a single AP application, place omni-directional antennas as close to the center of the coverage area as possible. For directional antennas, point the antenna in the direction of the desired coverage area. 142 ZyXEL G-570S v2 Users Guide APPENDIX E Customer Support Please have the following information ready when you contact customer support. Required Information Product model and serial number. Warranty Information. Date that you received your device. Brief description of the problem and the steps you took to solve it. Corporate Headquarters (Worldwide) Support E-mail: support@zyxel.com.tw Sales E-mail: sales@zyxel.com.tw Telephone: +886-3-578-3942 Fax: +886-3-578-2439 Web Site: www.zyxel.com, www.europe.zyxel.com FTP Site: ftp.zyxel.com, ftp.europe.zyxel.com Regular Mail: ZyXEL Communications Corp., 6 Innovation Road II, Science Park, Hsinchu 300, Taiwan Costa Rica Support E-mail: soporte@zyxel.co.cr Sales E-mail: sales@zyxel.co.cr Telephone: +506-2017878 Fax: +506-2015098 Web Site: www.zyxel.co.cr FTP Site: ftp.zyxel.co.cr Regular Mail: ZyXEL Costa Rica, Plaza Roble Escaz, Etapa El Patio, Tercer Piso, San Jos, Costa Rica Czech Republic E-mail: info@cz.zyxel.com Telephone: +420-241-091-350 Fax: +420-241-091-359 Web Site: www.zyxel.cz Regular Mail: ZyXEL Communications, Czech s.r.o., Modransk 621, 143 01 Praha 4 -

Modrany, Cesk Republika ZyXEL G-570S v2 Users Guide 143 Appendix E Customer Support Denmark Support E-mail: support@zyxel.dk Sales E-mail: sales@zyxel.dk Telephone: +45-39-55-07-00 Fax: +45-39-55-07-07 Web Site: www.zyxel.dk Regular Mail: ZyXEL Communications A/S, Columbusvej, 2860 Soeborg, Denmark Finland Support E-mail: support@zyxel.fi Sales E-mail: sales@zyxel.fi Telephone: +358-9-4780-8411 Fax: +358-9-4780 8448 Web Site: www.zyxel.fi Regular Mail: ZyXEL Communications Oy, Malminkaari 10, 00700 Helsinki, Finland France E-mail: info@zyxel.fr Telephone: +33-4-72-52-97-97 Fax: +33-4-72-52-19-20 Web Site: www.zyxel.fr Regular Mail: ZyXEL France, 1 rue des Vergers, Bat. 1 / C, 69760 Limonest, France Germany Support E-mail: support@zyxel.de Sales E-mail: sales@zyxel.de Telephone: +49-2405-6909-0 Fax: +49-2405-6909-99 Web Site: www.zyxel.de Regular Mail: ZyXEL Deutschland GmbH., Adenauerstr. 20/A2 D-52146, Wuerselen, Germany Hungary Support E-mail: support@zyxel.hu Sales E-mail: info@zyxel.hu Telephone: +36-1-3361649 Fax: +36-1-3259100 Web Site: www.zyxel.hu Regular Mail: ZyXEL Hungary, 48, Zoldlomb Str., H-1025, Budapest, Hungary Kazakhstan Support: http://zyxel.kz/support Sales E-mail: sales@zyxel.kz 144 ZyXEL G-570S v2 Users Guide Appendix E Customer Support Telephone: +7-3272-590-698 Fax: +7-3272-590-689 Web Site: www.zyxel.kz Regular Mail: ZyXEL Kazakhstan, 43, Dostyk ave.,Office 414, Dostyk Business Centre, 050010, Almaty, Republic of Kazakhstan North America Support E-mail: support@zyxel.com Sales E-mail: sales@zyxel.com Telephone: +1-800-255-4101, +1-714-632-0882 Fax: +1-714-632-0858 Web Site: www.us.zyxel.com FTP Site: ftp.us.zyxel.com Regular Mail: ZyXEL Communications Inc., 1130 N. Miller St., Anaheim, CA 92806-

2001, U.S.A. Norway Support E-mail: support@zyxel.no Sales E-mail: sales@zyxel.no Telephone: +47-22-80-61-80 Fax: +47-22-80-61-81 Web Site: www.zyxel.no Regular Mail: ZyXEL Communications A/S, Nils Hansens vei 13, 0667 Oslo, Norway Poland E-mail: info@pl.zyxel.com Telephone: +48 (22) 333 8250 Fax: +48 (22) 333 8251 Web Site: www.pl.zyxel.com Regular Mail: ZyXEL Communications, ul. Okrzei 1A, 03-715 Warszawa, Poland Russia Support: http://zyxel.ru/support Sales E-mail: sales@zyxel.ru Telephone: +7-095-542-89-29 Fax: +7-095-542-89-25 Web Site: www.zyxel.ru Regular Mail: ZyXEL Russia, Ostrovityanova 37a Str., Moscow, 117279, Russia Spain Support E-mail: support@zyxel.es Sales E-mail: sales@zyxel.es Telephone: +34-902-195-420 Fax: +34-913-005-345 ZyXEL G-570S v2 Users Guide 145 Appendix E Customer Support Web Site: www.zyxel.es Regular Mail: ZyXEL Communications, Arte, 21 5 planta, 28033 Madrid, Spain Sweden Support E-mail: support@zyxel.se Sales E-mail: sales@zyxel.se Telephone: +46-31-744-7700 Fax: +46-31-744-7701 Web Site: www.zyxel.se Regular Mail: ZyXEL Communications A/S, Sjporten 4, 41764 Gteborg, Sweden Ukraine Support E-mail: support@ua.zyxel.com Sales E-mail: sales@ua.zyxel.com Telephone: +380-44-247-69-78 Fax: +380-44-494-49-32 Web Site: www.ua.zyxel.com Regular Mail: ZyXEL Ukraine, 13, Pimonenko Str., Kiev, 04050, Ukraine United Kingdom Support E-mail: support@zyxel.co.uk Sales E-mail: sales@zyxel.co.uk Telephone: +44-1344 303044, 08707 555779 (UK only) Fax: +44-1344 303034 Web Site: www.zyxel.co.uk FTP Site: ftp.zyxel.co.uk Regular Mail: ZyXEL Communications UK, Ltd.,11 The Courtyard, Eastern Road, Bracknell, Berkshire, RG12 2XB, United Kingdom (UK)

+ is the (prefix) number you dial to make an international telephone call. 146 ZyXEL G-570S v2 Users Guide APPENDIX F Legal Information Copyright Copyright 2006 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice. Trademarks ZyNOS (ZyXEL Network Operating System) is a registered trademark of ZyXEL Communications, Inc. Other trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners. Certifications Federal Communications Commission (FCC) Interference Statement The device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operations. This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. ZyXEL G-570S v2 Users Guide 147 Appendix F Legal Information If this device does cause harmful interference to radio/television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1 Reorient or relocate the receiving antenna. 2 Increase the separation between the equipment and the receiver. 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4 Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.

Notices Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device has been designed for the WLAN 2.4 GHz network throughout the EC region and Switzerland, with restrictions in France. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Viewing Certifications 1 Go to http://www.zyxel.com. 2 Select your product on the ZyXEL home page to go to that product's page. 3 Select the certification you wish to view from this page. 148 ZyXEL G-570S v2 Users Guide ZyXEL Limited Warranty Appendix F Legal Information ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. Note Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind to the purchaser. To obtain the services of this warranty, contact ZyXEL's Service Center for your Return Material Authorization number (RMA). Products must be returned Postage Prepaid. It is recommended that the unit be insured when shipped. Any returned products without proof of purchase or those with an out-dated warranty will be repaired or replaced (at the discretion of ZyXEL) and the customer will be billed for parts and labor. All repaired or replaced products will be shipped by ZyXEL to the corresponding return address, Postage Paid. This warranty gives you specific legal rights, and you may also have other rights that vary from country to country. Registration Register your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products. ZyXEL G-570S v2 Users Guide 149 Appendix F Legal Information 150 ZyXEL G-570S v2 Users Guide Index Index command interface 26 configuration 46, 92 configuration file 91, 97 connections 101 contact information 143 copyright 147 coverage area 104 CTS (Clear to Send) 132 customer support 143 D data encryption 65 data modulation 104 data rate 104 default IP address 101 default settings 91, 93, 96, 97 depth 101 DHCP 96 DHCP client 101 DHCP relay 101 diagnostic tools 102 diagnostics 47, 102 dimensions 101 disclaimer 147 disconnect 92, 94 dynamic WEP 102 dynamic WEP key exchange 137 E EAP 101 EAP Authentication 135 encryption 65, 101, 102, 103, 138 error log 102 ESS 130 ESSID 97 ethernet ports 101 European plug standards 105 Extended Service Set, See ESS 130 151 A access 96 adaptor 95 address 51, 96, 101 address assignment 51 Advanced Encryption Standard See AES. advanced screens 46 AES 101, 102, 138 antenna 101, 104 directional 141 gain 141 omni-directional 141 AP (access point) 131 approvals 104 association list 49 auto MDI/MDI-X 101 auto-negotiating 101 B back up 91 backup 89, 91 Basic Service Set see BSS browser settings 96 BSS 129 C CA 136 cables 95 Certificate Authority See CA. certifications 147 notices 148 viewing 148 channel 65, 131 interference 131 channel ID 61, 68, 71 ZyXEL G-570S v2 Users Guide Index Extensible Authentication Protocol (EAP) 102 F factory defaults 91, 93, 96 FCC interference statement 147 features 101 file transfer protocol 97 firmware 93, 94, 97 fragmentation threshold 132 frequency 61 frequency range 104 FTP 26, 97 H hardware 102 height 101 hidden node 131 host ID 51 humidity (operation) 101 humidity (storage) 101 I IANA 51 IBSS 129 IEEE 802.11g 133 IEEE 802.1x 101, 102 IEEE standards compliance 101 Independent Basic Service Set See IBSS 129 initialization vector (IV) 138 interference 98 Internet access 98 Internet browser settings 96 IP address 51, 92, 96, 101 L language 89 LEDs 27, 95, 98, 102 login 96 logs 89, 90, 102 M MAC address 63, 101, 102, 103 maintenance 89 management 89, 102 managing the device good habits 27 using FTP. See FTP. using Telnet. See command interface. using the command interface. See command interface. using the web configurator. See web configurator. mask 51 Media Access Control address 63 Message Integrity Check (MIC) 138 modes 102 modulation 104 N navigation panel 46 network congestion 98 network disconnect 92, 94 network number 51 network statistics 47 North American plug standards 106 O operating frequency 61 operating humidity 101 operating modes 102 operating temperature 101 OTIST 102 output power 104 output power management 104 P packet log 102 152 ZyXEL G-570S v2 Users Guide Index S safety approvals 104 safety warnings 6 Secure Sockets Layer (SSL) 103 security 65, 101, 102 sensitivity 104 settings 47 signal interference 98 signal strength 49, 50, 65, 98 size 101 SSID 65 standards compliance 101 statistics 47, 48 status 47 storage humidity 101 storage temperature 101 subnet 96 subnet mask 51 default 101 syntax conventions 4 syslog 102 system status 47 T TCP/IP setup 91 Telnet 97 temperature (operation) 101 temperature (storage) 101 Temporal Key Integrity Protocol (TKIP) 138 tools (diagnostic) 102 trace log 102 trademarks 147 transmission types 104 troubleshooting 95 U upload configuration 92 upload firmware 93 packet statistics 48 Pairwise Master Key (PMK) 138, 139 password 89, 91, 96, 97, 101 port status 48 ports 101 power 104 power adaptor 95 power adaptor specifications 105 power cord 95 power management 104 power requirements 101 preamble mode 133 priorities 59 private IP address 51 private networks 51 problem solving 95 product registration 149 protocol support 101 PSK 138 Q QoS 59 QoS priorities 59 R RADIUS 134 message types 135 messages 135 shared secret key 135 registration product 149 related documentation 3 reset 93, 96, 97, 102, 103 restart automatic 92, 94 restore 89, 91, 92 RF frequency range 104 RF interference 98 RJ-45 101 roaming 102 rom-0 file 91 romfile 91 RTS (Request To Send) 132 threshold 131, 132 ZyXEL G-570S v2 Users Guide 153 Index W warranty 149 note 149 WDS 65 web configurator 26 weight 101 WEP 101, 102, 103 width 101 Wi-Fi Multimedia QoS 59 Wi-Fi Protected Access 137 wireless association 47, 49 wireless channel 97 wireless client WPA supplicants 139 Wireless Distribution System (WDS) 65, 102 wireless frequency 61 wireless interference 98 wireless LAN 97, 103 wireless modes 101 wireless security 65, 97, 101, 102, 133 wireless sensitivity 104 wireless signal strength 65 wireless specifications 104 WLAN interference 131 security parameters 140 WMM 59 WMM priorities 59 WPA 101, 102, 137 key caching 138 pre-authentication 138 user authentication 138 vs WPA-PSK 138 wireless client supplicant 139 with RADIUS application example 139 WPA2 137 user authentication 138 vs WPA2-PSK 138 wireless client supplicant 139 with RADIUS application example 139 WPA2-Pre-Shared Key 137 WPA2-PSK 137, 138 application example 139 WPA-PSK 137, 138 application example 139 154 ZyXEL G-570S v2 Users Guide