FCC ID: 2A9ZA-BADGERP BadgeR+

BadgeR+ Product Manual Developed by 911Cellular www.911cellular.com support@911cellular.com 216.283.6100 BadgeR+ Product Manual Developed by 911Cellular This Product Manual is intended to give you the guidance you need to effectively configure and use the BadgeR+ wearable device. In addition to using this document, we encourage you to take advantage of the wealth of information available at www.911Cellular.com/BadgeR+Maunal. If at any time you have questions, need help, or have suggestions for how to improve this Product Manual, please contact Support@911Cellular.com Device elements 1. Alert Button 2. Status / Pairing Button 3. Battery Indicator Lights 4. Status Indicator Light 5. Microphone Hole 6. Reset Button 7. Charging Port Element 1: Alert Button The alert button has 3 possible modes of operation:

Single click Double click 1 BadgeR+ Product Manual Developed by 911Cellular Press and hold Each mode can be configured by your organization to correspond to a specific type of alert. Please ask your manager for specific information about how your organization has configured the alert button. Element 2: Status / Pairing Button The button performs two functions:

1. Pressing and releasing the Status / Pairing Button triggers a connection test and a remaining battery check. The amount of battery remaining is indicated by the three white LED lights. More detail available in Element 3 description. A connection test determines (1) if the device is connected to the WiFi network, (2) if the access points within range of the device exist within the 911Cellular system and (3) if the device is able to communicate with the 911Cellular servers. If the Status Indicator Light turns GREEN and blinks four times, the device is connected to the WiFi network, the nearby access points exist within the 911Cellular system and the device is able to communicate with the 911Cellular servers. If the Status Indicator Light turns RED and blinks three times-the device is not connected to the WiFi network. If the Status Indicator Light turns ORANGE and blinks six times-the access points within range of the device do not exist in the 911Cellular system. If the Status Indicator Light turns YELLOW and blinks nine times-the device is unable to communicate with the 911Cellular servers. 2. This button allows you to enter into Bluetooth Pairing Mode, which is how you connect your device to the WiFi network. To enter Bluetooth Pairing Mode, press and hold the Battery Life /

Pairing Button for 10 seconds. After 10 seconds, you will see the Status Indicator Light turn on and display a blue color, which indicates that you have entered Bluetooth Pairing Mode. Element 3: Battery Indicator Lights When you check the remaining battery, if there is sufficient charge, you will see at least one of the three white LED lights turn on. These 3 white LED lights indicate the amount of battery still remaining. All three LEDs are on Your battery has between 70% and 100% of its total capacity remaining. Two of the three LEDs are on Your battery has between 40% and 70% of its total capacity remaining. One of the three LEDs are on Your battery has between 10% and 40% of its total capacity remaining. 2 One of the three LEDs is flashing Your battery has less than 10% of its total capacity remaining and should be charged immediately. BadgeR+ Product Manual Developed by 911Cellular The three LEDs are cycling between on and off The battery is currently being charged. Element 4: Status Indicator Light This single LED light performs two functions:

1. The light will illuminate a solid green color to indicate a successful activation of the Alert Button. This light will remain for as long as data is transmitted to the web portal. 2. The light will illuminate a blinking blue color when the device has been placed in bluetooth pairing mode. The Status Indicator Light will turn to solid blue when the device has been successfully paired. After the pairing and authentication processes are successfully completed, the Status Indicator Light will turn off. Element 5: Microphone Hole If this feature is enabled by your organization, this small cutout in the case allows the device's microphone to transmit audio after you trigger an alert. Element 6: Reset Button In case of button malfunction a paperclip or other pinhole device can be used to depress the reset button and restart the device. This does not wipe any previous configurations from the button. Element 7: Charging Port Your BadgeR+ can be charged via the USB-C port contained on the side of the device. Connecting Your Device For detailed information on how to connect your device to a WiFi network, visit www.911Cellular.com/Badger Triggering An Alert The BadgeR+ supports single click activation, double click activation, and press-and-hold activation;

however, your organization may not be using all of these combinations. Check with members of your security department to see exactly what actions are required to trigger an alert. You will know an alert has successfully been triggered when you see the green blinking (4 times) of the Status Indicator Light 3 BadgeR+ Product Manual Developed by 911Cellular Charging Your Device Each BadgeR+ is shipped with a USB-C charging cable. Plug one end of the cable into a power source, and the other end into your BadgeR+. To see if the device is charging, press the Status /

Pairing Button. Caring For Your Device While the electronics are enclosed in a sturdy case, it is still important that you keep your device away from water, as it may damage the components. FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:

This device meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. The SAR limit of USA (FCC) is 1.6 W/kg averaged. BadgerR+ (Contains FCC ID: 2A9ZA-BADGERP) has also been tested against this SAR limit. SAR information on this and other pad can be viewed online at http://www.fcc.gov/oet/ea/fccid/. Please use the device FCC ID number for search. This device was tested simulation typical 0mm to body. To maintain compliance with FCC RF exposure requirements, use accessories should maintain 4 a separation distance between the user's bodies mentioned above, use accessories should not contain metallic components in its assembly, the use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. BadgeR+ Product Manual Developed by 911Cellular 5

Reference No.: WTX23X02010330W Page 1 of 4 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

Reference No.: WTX23X02010325W Page 1 of 3 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

911Cellular Olicel i U lo i | 6001 Cochran Road Solon, OH 44139 Date: 02/20/23 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A9ZA-BADGERP Attestation Statements Part 2.91 1(d)(5)(i) Filing To whom it may concern, 911Cellular, certifies that the equipment is seeking authorization is not on the List of Equipment and Services Covered by Section 2 of the Secure Networks Act, which it is prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Chad Salahshour CEO

911Cellular Olicel | u lar 6001 Cochran Road Solon, OH 44139 Date: 02/20/23 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A9ZA-BADGERP Attestation Statements Part 2.911(d)(5)(ii) Filing To whom it may concern, 911Cellular certifies that, as of the date of the filing of the application, 911Cellular is not identified on the List of Equipment and Services Covered by Section 2 of the Secure Networks Act, as an entity producing covered equipment. Sincerely, Chad Salahshour CEO

911Cellular 6001 Cochran Road Solon, OH 44139 Date: 03/01/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A9ZA-BADGERP Request for Class II Permissive Change To whom it may concern, This is a request to file a Class II permissive change for FCC ID: 2A9ZA-BADGERP. In the new use case, the Bluetooth function is turned off through firmware, and this module is now being used in a portable device. The module has not been changed in anyway. The summary changes filed under this application are:

Original Module Present Portable Device FCC ID FCC ID: 2A9ZA-BADGERP FCC ID: 2A9ZA-BADGERP Radio Spec Wifi and Bluetooth LE V5.0 Wifi Antenna Type Internal Antenna Internal Antenna Antenna Gain 3.96 dBi 3.96dBi We have performed the SAR evaluation, and the radiated spurious emission of this portable device, the device meets the FCC portable device requirements. The designated host name is BadgeR+ and the model is 2.

Reference No.: WTX23X02010330W Page 2 of 4 EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Reference No.: WTX23X02010330W Page 3 of 4 Host View 1 Host View 2 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

911Cellular Olicellular | 6001 Cochran Road Date: 02/20/23 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A9ZA-BADGERP Declaration of Authorization To vvhom it may concern, I, te@ undersigned, hereby authorize, Jandy So, of Waltek Testing Group (Shenzhen) Co., Ltd.,

(VALTEK) to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Jandy So, of Waltek Testing Group (Shenzhen) Co., Ltd., (WALTEK) on our behalf shall have the same effects as acts of our own.

|, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C 853(a). This authorization is valid until further written notice from the applicant. Sincerely, Signatuse:

bia had Salahshour CEO

911Cellular Olicel | u la ig 6001 Cochran Road Solon, OH 44139 Date: 02/24/23 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A9ZA-BADGERP US Agent Attestation Statement / Part 2.911(d)(7) To whom it may concem, 911Cellular certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Designated U.S. Agent Information:

Name: 911Cellular FRN: 0033264516 Address: 6001 Cochran Road, Solon, Ohio 44139, United States Contact Person: Chad Salahshour Tel.: (216) 283-6100 Email:Chad@911Cellular.com Sincerely, Chad Salahshour CEO

911Cellular Olicellular 6001 Cochran Road Solon, OH 44139 Date: 02/20/23 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Request for Change of Identification To whom it may concern, This Change of Identification request applies for a new FCC ID; as established in 47 CFR 2.933(b) for a currently approved device. This application by 911Cellular will establish a new FCC ID: 2A9ZA-BADGERP under 911Cellulars grantee code for purpose of marketing. The original grant to Espressif Systems (Shanghai) Co., Ltd will remain in effect. Per 2.933(b):

e The original identification is 2AC7Z-ESPC3MINI1 e The original grant date is 06/16/2021 e The equipment is electrically ideniical. Only the model name, trade name, and FCC ID are different e The original test results are applicable and representative of this changed device e Exterior photographs are included in this application. External photos with label location and type label sample drawing are electronically submitted as attachments. Sincerely, Chad Salahshour CEO

Date: 01/31/22 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Authorization for Change of Identification To whom it may concern, This letter grants authorization for 911Cellular to apply to the FCC for a change in identification as specified under 47 CFR Section 2.933 of the FCC rules. This authorization applies to Espressif module, FCC ID: 2AC7Z-ESPC3MINI1. We are aware that 911Cellular intends to market the above referenced product under FCC ID:

2A9ZA -BADGERP. Sincerely, Signature:

Mia Zhou Regulatory Compliance Manager