60GHz WirelessHD Transceivers User Manual Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. In order to comply with FCC RF Exposure requirements, a separation distance of at least 20 cm must be maintained between the antenna and all persons. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
Consult the dealer or an experienced radio/TV technician for help. Table of Contents CHAPTER 1: INTRODUCTION...................................................................................................................................1 OVERVIEW ....................................................................................................................................................................... 1 FEATURES ........................................................................................................................................................................ 1 PACKAGE CONTENTS......................................................................................................................................................... 2 APPLICATION DIAGRAM .................................................................................................................................................... 2 CHAPTER 2: HARDWARE INSTRUCTION .............................................................................................................3 60GHZ WIRELESSHD TRANSMITTER ................................................................................................................................ 3 TX Front Panel Configuration................................................................................................................................ 3 TX Rear Panel Configuration................................................................................................................................. 4 TX Side Panel Configuration.................................................................................................................................. 5 60GHZ WIRELESSHD RECEIVER ...................................................................................................................................... 6 RX Front Panel Configuration................................................................................................................................ 6 RX Rear Panel Configuration................................................................................................................................. 7 RX Side Panel Configuration.................................................................................................................................. 7 REMOTE CONTROLLER ...................................................................................................................................................... 8 CHAPTER 3: INSTALLATION.....................................................................................................................................9 SET UP STEPS.................................................................................................................................................................. 9 CHAPTER 4: SOFTWARE UPGRADE......................................................................................................................12 SOFTWARE APPLICATION INSTALLATION.......................................................................................................................... 12 START TO UPGRADE ....................................................................................................................................................... 16 CHAPTER 5: SPECIFICATIONS ..............................................................................................................................19 SPECIFICATIONS............................................................................................................................................................. 19 Video Format......................................................................................................................................................... 20 Audio Format......................................................................................................................................................... 20 Chapter 1: Introduction Overview For coming huge flat TV screen and high definition resolution, users like to set up the AV system in living room, but the cable placement always is a great harassment to the interior house. Also the HDMI cable is as expensive as the length as be. Users deserve to have a wireless cable replacement to match their high class AV systems. Here shows up a high edge solution to meet users equipment: 60GHz WirelessHD Audio-Video Transceivers!
This elegant product has HDMI interface to take multiple content sources like multimedia center, Blue ray player and Set-Top Box, without compressing of content, the WirelessHD technology will offer multiple gigabit throughout for Full HD video transmission. Users do not need to worry about video quality for lower transmission bandwidth anymore. It also has compliance to WirelessHD, HDMI, and DTCP for content security and quality assurance. Features
36 antennas array
Auto tracing - smart antenna
Least interference - 60GHz transmission
1080P 60f 50 Hz/ 59.94 Hz/ 60Hz global capability
Full HD 1080P 60f non-compressing image wireless transmission
Support HDCP/ DTCP for content security and quality assurance
4Gb/sec. wireless transmission
Multiple TX to single RX availability 1 Package Contents The following items should be included:
60GHz WirelessHD transmitter unit
60GHz WirelessHD receiver unit
User manual
Remote controller If any of the above items are damaged or missing, please contact your dealer immediately.
Two-piece of HDMI cables
Two-piece of power adapters
Warranty leaflet Application Diagram Notice!
For better transmitting quality, we strongly recommend to put the 60GHz WirelessHD Transceivers horizontally in open space, do not put them into cabinet or cupboard that will reduce the wireless transmitting signal. 2 Chapter 2:
Hardware Instruction 60GHz WirelessHD Transmitter TX Front Panel Configuration TX LED Indicators LED Color Behavior Power Green Pairing Blue Weak Green On Off Blinking On Off Blinking On Off Indication The LED will illuminate when the power is connected and the power switch is turned on. The LED will be dark when the power switch is turned off. Unit in sleep mode. The LED will illuminate to indicate which RX is being selected. If the pairing LED is off, user has to re-select again or reset both devices. Waiting for link. The LED will illuminate when the signal is weak. No link or no signal 3 Strong Green On Off The LED will illuminate when the signal is strong. Signal weak If 4 LEDs are blinking at same time, that means fan does nt work, please turn off unit and send to serv ice station. TX Rear Panel Configuration Configuration DC-IN Switch HDMI Connect the power adapter to the power DC-IN port. Switch the button to turn on or off the power supply. Connect HDMI cable one end to this HDMI port and the other to the DVD player or computer HDMI port. RS232 D-Sub Connect the RS232 D-Sub cable one end to this port, the other to the computer or laptop RS232 D-Sub port. 4 TX Side Panel Configuration TX Buttons Reset CFG (Configure) Press the RESET button to reset the system, the system will run through a full reset which takes approximately 5 seconds. This button is for upgrade system firmware. For further firmware upgrade process, please refer to Chapter 4:
Software Upgrade. No function This button is fixed and no function here. 5 60GHz WirelessHD Receiver RX Front Panel Configuration RX LED Indicators LED Color Behavior Power Green Pairing Blue Weak Green Strong Green On Off Blinking On Off Blinking On Off On Off Indication The LED will illuminate when the power is connected and the power switch is turned on. The LED will be dark when the power switch is turned off. Unit in sleep mode. The LED will illuminate to indicate which TX is being selected. If the pairing LED is off, user has to re-select again or reset both devices. Waiting for link. The LED will illuminate when the signal is weak. No link or no signal The LED will illuminate when the signal is strong. Signal weak If 4 LEDs are blinking at same time, that means fan does nt work, please turn off unit and send to serv ice station. 6 RX Rear Panel Configuration Configuration DC-IN Switch HDMI RS232 D-Sub Connect the power adapter to the power DC-IN port. Switch the button to turn on or off the power supply. Connect HDMI cable one end to this HDMI port and the other to the TV or computer HDMI port. Connect the RS232 D-sub cable one end to this port, the other to the projector or TV RS232 D-sub port. RX Side Panel Configuration 7 RX Buttons Reset Input Switch
( Pending ) Press the RESET button to reset the system, the system will run through a full reset which takes approximately 5 seconds. Press the RX unit "INPUT" button repeatedly to switch to desired source units (TX1/ TX2) and the PAIRING LED will illuminate to indicate which source unit is being selected. CFG (Configure) This button is for upgrade system firmware. For further firmware upgrade process, please refer to Chapter 4: Software Upgrade. Remote Controller Remote Controller Stand by Switch
( Pending ) The devices will be ready while this button clicking. Switch the pairing input source to different 60GHz WirelessHD Transmitters. 8 Chapter 3: Installation Set Up Steps 1. Connect the 60GHz WirelessHD Transmitter with cables to media input sources, such as a computer or a DVD player. 9 2. And connect 60GHz WirelessHD Receiver with cables to media output sources, such as a monitor or a projector. Notice!
Do not forget to turn on the power supplies of your monitor, projector or video device and switch them into corresponding settings. Such as, set your monitor sources into HDMI setting for media receiving. 10 3. Then, connect both power adapters of the 60GHz WirelessHD Transceivers to outlets. 4. Turn on the power of both 60GHz WirelessHD Transceivers. 5. After finished above set up steps, the 60GHz WirelessHD Transceivers will be ready to transmit media. 11 Chapter 4:
Software Upgrade Software Application Installation The devices would allow user to upgrade firmware into new version. Please download the new firmware and application from the supported website. (Please fill in the website link.) Then, install the application on your computer or laptop by the following steps. 1. When this screen shows up, please click Next to install. 12 2. Select destination location, click Next to continue or click Browse to change the location. 3. Select start menu folder, click Next to continue or click Browse to change the folder. 4. Select to create a short cut on the desktop, and then click Next to process. 13 5. When following screen shows up, it is ready to install the application on your computer. Please click Install to setup. 6. The application installing is completed, click Finish to exit. 14 15 Start to Upgrade 1. Connect the RS232 D-Sub cable one end to device, the other to the computer or laptop RS232 D-Sub port. 16 2. After confirming the hardware connection, please execute the software application that installed. Communication Select the Com Port that connects the computer with RS232 D-Sub cable to the transceiver. 1. Find and open the RF firmware file by click the button, the browser will display to correct file path. 2. Then, select the Product button to upgrade the program. 3. The upgrade status will show in the column below of the screen. 4. Wait for upgrade success message comes out from state log area. 5. If get fail message from state log area, please re-do the steps again. 6. After finished the firmware upgrade, please turn off 17 RF Board Program
(bin file) then on the power to complete the firmware upgrading. Notice : User can upgrade the RF firmware directly without pressing CFG button. 1. Turn off the power supply first, and hold the CFG
(Configure) button on the device turning on the power supply. Please remember to keep on holding the CFG
(Configure) button for two seconds. The LEDs will not illuminate at this time. 2. Then, find and open the Host firmware file by click the button, the browser will display to correct file path. 3. Then, select the Upload to Flash button to upgrade the program. 4. The upgrade status will show in the column below of the screen. 5. Wait for upgrade success message comes out from state log area. 6. If get fail message from state log area, please re-do the steps again 7. After finished the firmware upgrade, please turn off then on the power to complete the firmware upgrading. Click this button to check the host connection status. Click this button to set the system back to default settings. Click Cancel to give up and exit the upgrade process. Flash Program
(hex file) Check Host Set Default Cancel Notice!
The Transmitter, Receiver and RF parts firmware cannot be combined in one, thus user need to upgrade the firmware 18 separately. Chapter 5: Specifications Specifications Standards Frequency Input/ Output Interface Antenna Type Range AV Port WirelessHD 60 GHz HDMI Interface 36 Antenna Array (Integrate Ceramic) 10 meters indoors Transmitter : 1 Port (HDMI 1.3) Receiver : 1 Port (HDMI 1.3) Physical Specifications Weight: 324g10g Dimension: 183 (L) x 80 (W) x 36 (H) mm Adapter Power AC 90-230V @ 60Hz input, DC 12V 1.5A LED Indicators Transmitter: Four LEDs display, power, pairing indicator, signal Strength indication Receiver : Four LEDs display, power, pairing indicator, signal Strength indication, IR sensor 19 Operating Environment
(Total System) Operating Temperature: 0 ~ 50 ambient temperature Except AC adaptor, it is only 0 ~ 40 Storage Temperature: -30 ~ 70 Operating Humidity: 10% to 90% (Non-condensing) Storage Humidity: 5% to 90% (Non-condensing) I/O Port RS232 Interface Video Format Resolution Format
(CEA-861 Code) 24 Hz Vertical Refresh Rate 59.94 Hz 50 Hz 60 Hz 25 MHz 27 MHz 27 MHz 74.25 MHz 25.175 MHz 640x480p (1) 720x480p (2/3) 720x576p (17/18) 1280x720p (19) 1280x720p (4) 1920x1080i (20) 1920x1080i (5) 1920x1080p (32) 1920x1080p (31) 1920x1080p (16) 1. Specific format support is dependent on latest firmware release. 2. Deep color (10/12-bit/per color 4:4:4) is possible for all format but resolution 74.176 MHz 74.176 MHz 74.25 MHz 74.25 MHz 148.5 MHz 74.25 MHz 74.25 MHz 148.352 MHz 148.5 MHz 1080p (not supported in WirelessHD v1.0 specification). 3. Other video formats are possible to include PC formats (VGA, XGA, SXGA, etc.) Audio Format Audio up to 8-ch., 24-bit 192 kHz LPCM. 20 Multiples of Fs 128 256 512 32 kHz 4.096 8.192 16.384 44.1 kHz 5.645 11.290 22.579 48 kHz 6.144 12.288 24.576 88.2 kHz 11.290 22.579 45.158 96 kHz 12.288 24.576 49.152 176.4 kHz 22.579 45.158 19 2 4 Specific format support dependent on latest code release . 21