2.4GHz Wireless BlueTrace Mouse w/Nano Receiver USER'S GUIDE Ver.:1.00 CAUTION: To use this product properly, please read the user's guide before installing. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-
-
-
that to which the receiver is connected.
-
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Consult the dealer or an experienced radio/TV technician for help. 1 Functional Introduction 1. Left button 2. Right button 3. Scrolling Wheel 4. Forward 5. Backward DPI Switch The LED indicator under tilt wheel will light up when plug the mouse into USB port. The brightness of the indicator indicates the DPI setting in use. There are three different setting:
Bright:1600 DPI Dim: 1300 DPI No light: 800 DPI 6. DPI Switch Key (LED Indicator) 7. Nano Receiver 8. Battery Cover 9. Connect Button 10. ON/OFF Switch The default setting is 1600 DPI. You can easily switch between DPI setting. In order to save power, the LED display will only last for 10 seconds. 2 Forward Press this button to view the next page in your Internet browser. Backward Press this button to view the previous page in your Internet browser. Installing the batteries Step 1: Take the battery cover off. Step 2: Insert the battery as shown inside the battery compartment. Step 3: Recover the cover.
**Warning:
*Please insert the battery with the correct polarity according to the instruction labeled on the mouse. AA Battery X 1 Pull 3 Step 4: Turn on power switch Step 5: If you need to travel with your wireless mouse, made sure turn off the POWER SWITCH. Setup the Connection between the Receiver and the Mouse 1. Insert the battery into the mouse, then follow the steps below. 2. In the meantime, a storage slot on the back to storage the receiver , take the nano receiver out. 4 3. Plug the Nano receiver into the USB port on your computer. 4. If the mouse does not work, please put it into pairing mode. 5. Pairing: Re-plug the receiver into the USB port on your computer, then press the connect button on the mouse. If the mouse does not work after 10 seconds, pair them again. (The receiver has auto pairing function). 6. The LED indicator on mouse flashes steadily when it is in pairing mode and stops blinking when it is successfully paired with the receiver. 7. When low battery, the battery indicator on the mouse will start to blink. DPI Switch Key LED Indicator
*LED Indicator LED is on for 3 sec. Power ON LED Blinks for 3 times During Pairing (LED OFF when paired or failed after 10 sec.) LED Blinks for 10 sec. Low Battery Warning DPI Indicated
(when DPI switched) 5 GREEN LED FLASH (0.5 sec. Regularly) GREEN LED FLASH (if any action) GREEN LED ON Searching the channel Channel connected No action Connect to the USB or Mouse port of your computer