FCC ID: CFS8DLDT80XXV Dual Technology Motion Sensor

DT8035V Dual Technology Motion Sensor Dtecteur de mouvement double technologie Sensor de movimiento de tecnologa dual Sensor de movimento de tecnologia dupla Quick Installation Guide Guide dinstallation rapide Gua Rpida de instalacin Guia rpido de instalao 2 2 3 1 6' 9" - 8' 9"

(2.1 - 2.7 m) 7' 6"

(2.3 m)

> 6'

(1,8 m) Optimal Optimal Optimo timo 100 lbs Pet applications vary, walk test to determine attainable pet immunity level. L'immunit aux petits animaux peut varier. Raliser un test de dtection afin de vrifier le niveau d'immunit. Para aplicaciones con mascotas, utilice el test de andado para determinar el nivel de inmunidad contra mascotas alcanzable. Para aplicativos para animais de estimao, use o teste de caminhada para determinar o nvel de imunidade do animal de estimao atingvel.

/ 45 kg 1 1 4 ON

OFF ON OFF PI LED

OFF ON O N O F F P I L E D

* Factory default / Valeurs par dfaut du fabricant /

Defecto de fbrica / Padro de fbrica DT8035V Microwave Range Adjustment Rglage de la porte des micro-ondes Ajuste del rango de deteccin Microondas Ajuste de Alcance Microondas MIN

MAX MW SENSITIVITY

(Sensibilit micro-ondes)

(Sensibilidad de Microonda)

(Sensibilidade da Microonda) Pet Immunity ON Insensibilit aux animaux Tolerancia a mascotas Pet-Imunidade OFF PI LED

*Enabled

*Activ

*Habilitado

*Habilitado Disabled Dsactiv Deshabilitado Deshabilitado

LOOKDOWN MIN MAX MW OFF 22-20 AWG

(0.31-0.52mm2) 5 2 Tamper 30 mA 25 VDC Alarm 30 mA 25 VDC Power 17 mA 9-15 VDC

(UL: 9.5-15 VDC) T 6 T 5 C NC V- V+

4 3 2 1 Panel / Panneau / Panel / Controle Zone COM Zone

Zone COM Zone

Ground +12V T 6 T 5 C 4 NC 3 V- V+

2 1 Sensor / Dtecteur / Sensor / Sensor MIN

MAX Walk Test Reset MW SENSITIVITY

< 4 (1.2m) ON 1/2 sec. hold 4x PI LED 1 2 30 sec 45 0 30 10 20 1. Close the sensor and apply power. Initialization is complete when the LED stops flashing slowly (about 30 seconds). 2. Turn the microwave sensitivity counterclockwise to reduce the microwave range (minimum = 16.4 / 5m) and close the sensor. 3. Walk through the detection area and observe the LED. 4. Adjust the microwave range as necessary to meet installation requirements. Power Up Walk Test Normal LED Red Slow Blink Yellow OFF Microwave Microwave ON Alarm ON ON PIR ON Alarm ON ON PIR Green OFF Walk test mode is active for 10 minutes, then automatically exits test mode, disables the LED and enters normal operation mode. For an additional 10 minute walk test, enable walk test mode again with the flashlight feature (see Walk Test Reset above). Note: During power up and walk test modes the LED is active regardless of the LED Enable/Disable DIP switch setting. 0 V

6 0 0

V 5 3 0 8 T D Fault Fast Blink OFF OFF 6 6 7 Top View Vue de dessus Vista Desde Arriba Vista Superior PLAN VIEW ALL ZONES Side View Vue de cot Vista Lateral Vista Lateral A B C D Zones / Zones / Zonas / Zonas A 2 Look-down / Basses / Vista Zona 0 / Vigilncia inferior B 18 Lower / Courtes / Cercana/ Mais baixas C 46 Intermediate / Intermdiaires / Intermedia /

Intermdias D 36 Long / Longues / Largo Alcance / Longo alcance MASK D C B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 5 0 4 0 5 5 1

0 0 8 1 10 19 28 37 11 20 29 42 45 48 2 3 4 5 6 7 8 9 13 22 31 12 21 30 38 14 23 32 39 43 46 49 15 24 33 16 25 34 40 17 18 26 27 35 36 41 44 47 50 LENS 0 V

7 0 0

V 5 3 0 8 T D

- 2 -

SPECIFICATIONS Operating Temperature: .................................................................................................................................................... 14 to 131F / -10 to 55C Relative Humidity: .................................................................................................................................. 5 to 93% (UL tested at 93%); non-condensing Dimensions: ........................................................................................................................................................ 3.86 x 2.24 x 1.69in / 98 x 57 x 43mm Tamper: .................................................................................................................................................................... Cover and Wall Tamper Protection Electrical Power: .......................................................................................................................................... 15mA (normal use); 17mA (maximum use) Microwave Frequency: ................................................................................................................................................................................ 10.525GHz Range: ........................................................................................................................................ Cone shape detection area of 40 x 56ft (12.2 x 17.1m) Pet Immunity: ................................................................................................................................................................................... Up to 100lb / 45kg) TROUBLESHOOTING Alarm Relay Red LED NORMAL Closed Off TROUBLE*

Self-Test Failure1 Open Flashing

*TROUBLE CONDITIONS 1 Self-Test Failure conditions:

Microwave supervision failure: The sensor is operating in PIR mode only. PIR self-test failure: The sensor is disabled. Temperature compensation failure: The temperature compensation is disabled. Depending on the Trouble condition, take the following corrective actions:

Verify the power supply is sufficient (at least 9V at the sensor). Cycle power to the sensor. Walk test the sensor. If the Trouble condition does not clear, replace the sensor. APPROVAL LISTINGS FCC part 15, Class B verified IC ICES-003, Class B verified UL 639 ULC S306-03 SIA-PIR-01 Passive Infrared detector standard features for false alarm immunity. Product must be tested at least once each year / Le fonctionnement du produit doit tre vrifi au moins une fois par anne /

El producto debe ser probado al menos una vez al ao / O produto deve ser testado pelo menos uma vez por ano All wiring must be in accordance with: the National Electrical Code (ANSI/NFPA70); the Canadian Electrical Code, Part I (where applicable);

UL681, Standard for Installation and Classification of Burglar and Holdup Alarm Systems; ULC-S302, Standard for Installation and Classification of Burglar Alarm Systems for Financial and Commercial Premises, Safes and Vaults; ULC-S310, Standard for Installation and Classification of Residential Burglar Alarm Systems; local codes and the authorities having jurisdiction. The products are intended to be powered by a power-limited output of a UL/CUL Listed Burglar Alarm control unit, or via a Listed UL603/ULC-

S318 power-limited power supply that provides 4 hours of standby power. The sensor must be mounted indoors, within the protected premises, and on a wooden stud, solid wood or with a robust wall anchor. UL Notes: All interconnecting devices must be UL listed. The pet immunity feature has not been evaluated by UL. FEDERAL COMMUNICATIONS COMMISSION STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC/IC NOTICE: This device complies with Part 15 of the FCC Rules, and RSS-210 of IC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable.

- 3 -

TO THE INSTALLER Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system. The installer should assume the responsibility of developing and offering a regular maintenance program to the user, as well as acquainting the user with the proper operation and limitations of the alarm system and its component parts. Recommendations must be included for a specific program of frequent testing (at least weekly) to insure the systems operation at all times. REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. Responsible Party / Issuer of Suppliers Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive., Melville, NY 11747, Ph: 516-577-2000 The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health. Any attempt to reverse-engineer this device by decoding proprietary protocols, de-compiling firmware, or any similar actions is strictly prohibited. To protect the environment, a detailed installation guide is available on the Resideo website Please consider before printing the document!

SUPPORT & WARRANTY INFORMATION For the latest documentation, support, and warranty information please go to:

www.resideo.com This product manufactured by Resideo Technologies and its affiliates 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 2020 Resideo Technologies, Inc. www.resideo.com R800-26065A 5/20 Rev. A

DT8050V Dual Technology Motion Sensor Dtecteur de mouvement double technologie Sensor de movimiento de tecnologa dual Sensor de movimento de tecnologia dupla Quick Installation Guide Guide dinstallation rapide Gua Rpida de instalacin Guia rpido de instalao 2 2 3 1 6' 9" - 8' 9"

(2.1 - 2.7 m) 7' 6"

(2.3 m) Optimal Optimal Optimo timo 0 V

1 0 0

E V _ R P I 1 1 4 ON

OFF

*Factory default / Valeurs par dfaut du fabricant /

Defecto de fbrica / Padro de fbrica DT8050V Microwave Range Adjustment Rglage de la porte des micro-ondes Ajuste del rango de deteccin Microondas Ajuste de Alcance Microondas MIN

MAX MW SENSITIVITY

(Sensibilit micro-ondes)

(Sensibilidad de Microonda)

(Sensibilidade da Microonda) LOOKDOWN MIN MAX MW OFF ON L E D O N O F F Not Used Non utilis No utilzado No usado

ON OFF LED DT8050V_004_V0 22-20 AWG

(0.31-0.52mm2) 5 2 Tamper 30 mA 25 VDC Alarm 30 mA 25 VDC Power 17 mA 9-15 VDC

(UL: 9.5-15 VDC) T 6 T 5 C NC V- V+

4 3 2 1 Panel / Panneau / Panel / Controle Zone COM Zone

Zone COM Zone

Ground +12V T 6 T 5 C 4 NC 3 V- V+

2 1 Sensor / Dtecteur / Sensor / Sensor MIN

MAX MW SENSITIVITY Walk Test Reset

< 4 (1.2m) ON 1/2 sec. hold 4x LED 1 2 30 sec 45 0 30 10 20 1. Close the sensor and apply power. Initialization is complete when the LED stops flashing slowly (about 30 seconds). 2. Turn the microwave sensitivity counterclockwise to reduce the microwave range (minimum = 16.4 / 5m) and close the sensor. 3. Walk through the detection area and observe the LED. 4. Adjust the microwave range as necessary to meet installation requirements. Power Up Walk Test Normal LED Red Slow Blink Yellow OFF Microwave Microwave ON Alarm ON ON PIR ON Alarm ON ON PIR Green OFF Fault Fast Blink OFF OFF Walk test mode is active for 10 minutes, then automatically exits test mode, disables the LED and enters normal operation mode. For an additional 10 minute walk test, enable walk test mode again with the flashlight feature (see Walk Test Reset above). Note: During power up and walk test modes the LED is active regardless of the LED Enable/Disable DIP switch setting. 6 7 Top View Vue de dessus Vista Desde Arriba Vista Superior PLAN VIEW ALL ZONES Side View Vue de cot Vista Lateral Vista Lateral A B C D Zones / Zones / Zonas / Zonas A 2 Look-down / Basses / Vista Zona 0 / Vigilncia inferior B 18 Lower / Courtes / Cercana/ Mais baixas C 20 Intermediate / Intermdiaires / Intermedia /

Intermdias D 54 Long / Longues / Largo Alcance / Longo alcance MASK D C B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 4 6 5 0 5 5 1

0 0 8 2 3 4 5 6 7 8 1 10 19 28 33 38 41 44 11 20 13 22 12 21 29 34 15 24 16 25 31 36 14 23 30 35 39 42 45 LENS 9 18 27 17 26 32 37 40 43 46 0 V

7 0 0

V 0 5 0 8 T D

- 2 -

SPECIFICATIONS Operating Temperature: .................................................................................................................................................... 14 to 131F / -10 to 55C Relative Humidity: .................................................................................................................................. 5 to 93% (UL tested at 93%); non-condensing Dimensions: ........................................................................................................................................................ 3.86 x 2.24 x 1.69in / 98 x 57 x 43mm Tamper: .................................................................................................................................................................... Cover and Wall Tamper Protection Electrical Power: .......................................................................................................................................... 15mA (normal use); 17mA (maximum use) Microwave Frequency: ................................................................................................................................................................................ 10.525GHz Range: .............................................................................................................................................. Cone shape detection area of 53 x 72ft (16 x 22m) TROUBLESHOOTING Alarm Relay Red LED NORMAL Closed Off TROUBLE*

Self-Test Failure1 Open Flashing

*TROUBLE CONDITIONS 1 Self-Test Failure conditions:

Microwave supervision failure: The sensor is operating in PIR mode only. PIR self-test failure: The sensor is disabled. Temperature compensation failure: The temperature compensation is disabled. Depending on the Trouble condition, take the following corrective actions:

Verify the power supply is sufficient (at least 9V at the sensor). Cycle power to the sensor. Walk test the sensor. If the Trouble condition does not clear, replace the sensor. APPROVAL LISTINGS FCC part 15, Class B verified IC ICES-003, Class B verified UL 639 ULC S306-03 SIA-PIR-01 Passive Infrared detector standard features for false alarm immunity. Product must be tested at least once each year / Le fonctionnement du produit doit tre vrifi au moins une fois par anne /

El producto debe ser probado al menos una vez al ao / O produto deve ser testado pelo menos uma vez por ano All wiring must be in accordance with: the National Electrical Code (ANSI/NFPA70); the Canadian Electrical Code, Part I (where applicable);

UL681, Standard for Installation and Classification of Burglar and Holdup Alarm Systems; ULC-S302, Standard for Installation and Classification of Burglar Alarm Systems for Financial and Commercial Premises, Safes and Vaults; ULC-S310, Standard for Installation and Classification of Residential Burglar Alarm Systems; local codes and the authorities having jurisdiction. The products are intended to be powered by a power-limited output of a UL/CUL Listed Burglar Alarm control unit, or via a Listed UL603/ULC-

S318 power-limited power supply that provides 4 hours of standby power. The sensor must be mounted indoors, within the protected premises, and on a wooden stud, solid wood or with a robust wall anchor. UL Notes: All interconnecting devices must be UL listed. FEDERAL COMMUNICATIONS COMMISSION STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC/IC NOTICE: This device complies with Part 15 of the FCC Rules, and RSS-210 of IC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable.

- 3 -

TO THE INSTALLER Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system. The installer should assume the responsibility of developing and offering a regular maintenance program to the user, as well as acquainting the user with the proper operation and limitations of the alarm system and its component parts. Recommendations must be included for a specific program of frequent testing (at least weekly) to insure the systems operation at all times. REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. Responsible Party / Issuer of Suppliers Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive., Melville, NY 11747, Ph: 516-577-2000 The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health. Any attempt to reverse-engineer this device by decoding proprietary protocols, de-compiling firmware, or any similar actions is strictly prohibited. To protect the environment, a detailed installation guide is available on the Resideo website Please consider before printing the document!

SUPPORT & WARRANTY INFORMATION For the latest documentation, support, and warranty information please go to:

www.resideo.com This product manufactured by Resideo Technologies and its affiliates 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 2020 Resideo Technologies, Inc. www.resideo.com R800-26066A 5/20 Rev. A

CFS8DLDT80XXV / 573F-DT80XXV EXHIBIT 6 Label Information LABEL INFORMATION EXACT LOCATION OF THE LABEL:

Label is located on the rear plastic case cover in the location shown:

Part 15.19 statement, molded into plastic Label location Page 1 of 2 EXHIBIT 6 Label Information LABEL CFS8DLDT80XXV / 573F-DT80XXV Page 2 of 2

2 Corporate Center Drive Melville, NY 11747 516-577-2000 CFS8DLDT80XXV FCC COVER LETTER Date: 07/28/2020 To Whom It May Concern:

This letter is to inform you of our request for a new certification for our transceiver known as CFS8DLDT80XXV. The transceiver will operate under Part 15.245. Models DT8035V and DT8050V are both certified under this application. Only the DT8050V, however, was fully tested. The DT8035V is considered compliant based on similarities. The only difference between the two models is the lens the DT8035V contains a lens that allows for a 35' range and the DT8050V uses a lens that is good for 50'. Regards, X Michael Antola

2 Corporate Center Drive Melville, NY 11747 516-577-2000 Request for Confidentiality Date: 07/28/20 Subject: Confidentiality Request for: CFS8DLDT80XXV Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 9.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Permanent Permanent*1 Short Term Permanent Short Term Short Term Short Term Short Term Short Term Permanent Permanent Permanent Permanent*3 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation

(Including both Functional Descriptions and Detailed Message Timing & Duty Factor Info) Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual Ademco Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify UL LLC in the event information regarding the product or the product is made available to the public. UL LLC will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By:

(Signature/Title2)

/ Hardware Engineer Michael Antola

(Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.