ADTZWM Wi-Fi and Z-Wave Module Installation and Setup Guide General Information The Communication Modules allow the control panel to communicate with the Central Station via the cellular radio network. The module connects directly to the control panel and is powered via the control panels connection. The ADTZWM communications module is intended to provide compatible ADT control panels with a Wi-Fi connection as well as connection with and the ability to control Z-Wave devices. Compatible Controls:
ADT7AIO/ADT5AIO Series - Installation Guide P/N 800-24121 or higher. ADTHYBWL Series - Installation Guide P/N 800-24125 or higher. ADT2X16AIO Series Installation Guide P/N 800-24341 or higher. Installing the Module in the ADT7AIO/ADT5AIO or ADT2X16AIO Series 1. Affix the provided FCC/IC label (P/N 800-
24286 on the controls case back (refer to Figure 1). HONEYWELL FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions: (1) This Device may not cause harmful interfer-
ence. (2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: CFS8DL-GRIPAIO7 IC: 573F-GRIPAIO7 IC MODEL: GRIPAIO7 800-24167 2/18 Rev A W Z F W L D 8 S F C
:
D I C C F W Z F W F 3 7
-
5
:
C I
:
E L U D O M S N A T N O C I W Z F W L D 8 S F C
:
D I C C F W Z F W F 3 7
-
5
:
C I
:
E L U D O M S N A T N O C I Figure 1. FCC/IC Label Location (ADT7AIO Shown) grip-020-V0 2. Remove the screw securing the rear case to the front case. 3. Slide the rear case down and separate from the front case. 4. Remove the communication module access cover. 5. Insert the ADTZWM into the slot on the left side of the control as shown in Figure 2 and ensure the receptacle is securely seated on the controls edge connector. 6. Secure the module with the provided SCREW SCREW screw. 7. Re-install the communication module access cover. 8. Install the rear case and secure with the screw. COVER 0 V
-
1 1 0
-
p i r g Figure 2. Installing the ADTZWM Module (ADT7AIO Shown) Installing the Module in the ADTHYBWL Series 1. Affix the provided FCC/IC label
(ADTZWM, P/N 800-24286) on the ADTHYBWL cabinet (refer to Figure 3) HONEYWELL GRIP HYBRID CONTROLLER FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions:
(1) This Device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. FCC ID: CFS8DL-GRIPH IC: 573F-GRIPH HVIN: GRIPH For Patent Information see: www.honeywell.com/patents Country of Origin: Mexico 800-24232 3/18 Rev A Model LCP500-L ETL Listed Household Fire and Burglar Warning Unit 3091091 Conforms to UL STD 985, 1023, 1635 Classified to ANSI/SIA CP01-2010 A
. v e R 5 1
/
0 1 5 6 4 1 2
-
0 0 8 NOT USED SLOT 1 LTE AUX/BELL_OC LED RUN LED IB2/ACTIVE LED RESERVED LED SLOT 2 WiFi / ZWAVE TAMPER SWITCH RJ-45 CONNECTOR G E N E R A L S L O T 3 BATTERY POWER LED AC POWER LED BATT+ BATT -
2 R E G G R T I 1 R E G G R T I D N G V 2 1 D E S U T O N 8-PIN TRIGGER CONNECTOR TRIGGER OUTPUT 1: 100mA MAX TRIGGER OUTPUT 2: 100mA MAX AUX OUTPUT LED
-
+
A B I H O L O L I H I H O L O L I H D N G X U A
}
AUX. PWR OUTPUT 10.5-13.8VDC 200mA MAX.
(120mA MAX. FOR UL INSTALLATIONS) ALL OUTPUTS ARE POWER LIMITED. 1 E N O Z 2 E N O Z 3 E N O Z 4 E N O Z 2000 OHMS EOLR 2000 OHMS EOLR 2000 OHMS EOLR 2000 OHMS EOLR I H I H I H O L O L I H O L O L 5 E N O Z 6 E N O Z 7 E N O Z 8 E N O Z 820 OHMS EOLR ALARM OUTPUT 10.513.8VDC, 2A MAX. (600mA MAX. FOR UL USAGE, INCLUDING AUX POWER) STEADY FOR 2000 OHMS EOLR 2000 OHMS EOLR 2000 OHMS EOLR 2000 OHMS EOLR BURGLARY/PANIC, TEMPORAL PULSE SOUNDING FOR FIRE. N R U T E R
)
-
(
D N G D A P H C U O T K C A L B
:
)
+
(
R E W O P D A P H C U O T D E R
:
A 2 B I D A P H C U O T W O L L E Y
:
B 2 B I D A P H C U O T N E E R G
:
A L A R M S TAT U S T RO U B L E CANCEL THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION'S STANDARD 72
(NATIONAL FIRE PROTECTION ASSOCIATION, BATTERYMARCH PARK, QUINCY, MA 02169). PRINTED INFORMATION DESCRIBING INSTALLATION, TESTING, MAINTENANCE, EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT. CONNECTION OF THE FIRE ALARM SIGNAL TO A FIRE ALARM HEAD-
QUARTERS OR CENTRAL STATION SHALL BE PERMIT-
TED ONLY WITH THE PERMISSION OF THE LOCAL AUTHORITY HAVING JURIDICTION. THE BURGLAR ALARM SIGNAL SHALL NOT BE CONNECTED TO A POLICE EMERGENCY NUMBER ZONE 1 USE FOR 2-WIRE SMOKE DETECTORS MAXIMUM NUMBER OF 2-WIRE SMOKE DETECTORS ON ZONE 1 IS 16 TO INTERNET CONNECTION 24-HR BATTERY STANDBY REQUIRED FOR FIRE INSTALLATIONS. USE 12V, 7AH BATTERY FOR 120mA AUX POWER. SEE INSTRUCTIONS. BATTERY CAPACITY FOR EMERGENCY BURGLARY STANDBY USE AT LEAST 4 HRS. CHARGING VOLTAGE 13.8VDC. MAXIMUM CHARGING CURRENT 650mA. SEALED LEAD-ACID TYPE. BATTERY NORMALLY NEED NOT BE REPLACED FOR AT LEAST THREE YEARS TO DETERMINE TOTAL STANDBY LOAD ON BATTERY, ADD 100mA TO TOTAL OF AUX. POWER AND REMOTE TOUCHPAD CURRENTS BLACK RED EARTH GROUND SEE INSTRUCTIONS**
FOR PROPER GROUNDING
+
C D
-
C D RECHARGEABLE BATTERY
(12V, 7AH) SEALED LEAD ACID TYPE 300-10211 13.5 VDC, 1.8A POWER SUPPLY TO 10VAC UNSWITCHED OUTLET
(24HR) MAX. ZONE RESISTANCE: (EACH ZONE) 300 OHMS (PLUS EOLR)
(USE EOLR PART NUMBER P4100 PART OF KIT SAHDWR1)
** FOR COMPLETE INFORMATION SEE INSTRUCTIONS 800-24126 OR HIGHER WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM. IN ADDITION, THIS SYSTEM MUST BE CHECKED BY A QUALIFIED TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS. 12V BELL. SEE INSTRUCTIONS. FOR BELL SUPERVISION, AND CONNECT RESISTOR DIRECTLY ACROSS EXTERNAL SOUNDER. USE 702 SIREN, OR PA N I C AWAY STAY 1 O F F 4 2 5 3 6 M A X T E S T B Y PA S S 7 8 9 I N S TA N T C O D E C H I M E 0
#
R E A DY DC+
DC -
WTP100 TOUCHPAD ASSEMBLED IN MEXICO 1501 Yamato Road Boca Raton, Florida 33431 2018 ADT Security Services ADTHYBWL-Series - Summary of Connections 800-24129 2/18 Rev.A W Z F W L D 8 S F C
:
D I C C F W Z F W F
-
3 7 5
:
C I
:
E L U D O M S N A T N O C I W Z F W L D 8 S F C
:
D I C C F
:
E L U D O M S N A T N O C I W Z F W F 3 7
-
5
:
C I Figure 3. FCC/IC Label Location grip-028-V0 2. Install the ADTZWM (ZWAVE) on the edge connector on the PCB (refer to Figure 4). Ensure the receptacle is securely seated on the edge connector. 3. Secure the module with the provided screw. E X T I N T LTE WiFi TX RXGND G E N E R A L TX RXGND BATT+ GND SCREW ADTZWM MODULE grip-012-V0 Figure 4. Installing the ADTZWM Module Programming 1. The ADTZWM requires a router and internet service for Wi-Fi connection. 2. Programming associated with the ADTZWM module is accomplished via the MobileTech app, as part of the control panel programming. Refer to the control panel installation and setup guide for additional information. Specifications ADTZWM Board Dimensions: 1.625 W x 2.625 L x 0.3125 D Current Drain: TBD Input Voltage: TBD Temperature: 32F (0C) to 140F (60C) REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE CONTROL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE SYSTEM. The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS FCC CLASS B STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
If using an indoor antenna, have a quality outdoor antenna installed. Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dIndustrie Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. RF Exposure Warning
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. Exposition aux Frequences Radio: L'antenne (s) utilise pour cet metteur doit tre installe une distance de sparation d'au moins 7,8 pouces (20 cm) de toutes les personnes. Mise en Garde USE OF THESE PRODUCTS IN COMBINATION WITH NON-HONEYWELL PRODUCTS IN A WIRELESS MESH NETWORK, OR TO ACCESS, MONITOR OR CONTROL DEVICES IN A WIRELESS MESH NETWORK VIA THE INTERNET OR ANOTHER EXTERNAL WIDE AREA NETWORK, MAY REQUIRE A SEPARATE LICENSE FROM SIPCO, LLC. FOR MORE INFORMATION, CONTACT SIPCO, LLC OR IPCO, LLC AT 8215 ROSWELL RD., BUILDING 900, SUITE 950, ATLANTA, GA 303350, OR AT WWW.SIPCOLLC.COM OR WWW.INTUSIQ.COM WARRANTY INFORMATION For Technical Support, call 1-877-748-7628, option 3 For documentation, call Customer Service at: 1-800-238-2727
(1-800-ADT-ASAP). For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa. Warranty Patents For patent information, see www.honeywell.com/patents ADT Security Services 1501 Yamato Road Boca Raton, FL 33431 2018 ADT Security Services 800-24197e 800-24197 3/18 Rev. A (BETA)