FCC ID: CFS8DL6RPTA Wireless Repeater

Installation and Setup Guide SiXRPTRA Wireless Repeater The SiXRPTRA is an RF receiver and a transmitter and is intended to extend the indoor range of SiX series devices. The SiXRPTRA receives alarm, status, and control messages from SiX series devices, and forwards these messages to control panel. The control then responds accordingly (arm/disarm the system, initiate an alarm, etc.). FEATURES Transmits its own status, including wall and case tamper, AC loss, low battery and RF Jam. Indicates RF Jam, AC/Battery Status, and RSSI (Received Signal Strength Indicator) using LEDs. RSSI indicates the signal condition between the repeater and the controller. Provides a 24-hour backup rechargeable battery. ETL listed to meet UL standards. GENERAL GUIDELINES Controller The SiXRPTRA module uses a 5VDC power supply to charge the battery. If the battery voltage drops to 3.6VDC a low battery occurs. NOTE: It is incapable of charging the battery if the voltage is lower than 2.6VDC (it must be replaced.) Conduct the SiX Auto System Check (see controllers instructions) to verify adequate signal strength, relocate if necessary. SiXRPTRA is designed to operate 200 feet through three walls of wood, aluminum and dry wall construction. When a single repeater installation is required. Range of the controller and sensor is more than 200 ft. line of sight. Signal Strength of sensors at using the programming app is worse than -75dBm for one or more sensors. Walk Test Failure of any Sensor/Keypad. If installation requires more than two floor communication. If more obstacles are interfering (more than three walls, high density metal doors, wood doors, multiple concrete walls, etc.) with communication between sensor and controller. No response from signal strength query from programming app or controller. When a second repeater installation is required. Same as Single Repeater installation except:

Range of the panel and sensor is more than 500 ft line of site, then install the controller in the middle with repeaters on either direction of the panel. If Installation requires more than 3 floor Communication. Install Controller on the middle Floor; then install Repeater based on the steady Amber RSSI (Signal Strength) LED indication as described in LED table below. NOTE: Maximum number of the repeater allowed in a system is two. The path of transmission is as follows: transmitter repeater controller. NOT transmitter repeater repeater receiver. COMPATIBILITY (REPEATER READY SYSTEM) All sensors (including keyfobs) connected to the controller should have revision Firmware Release #4 or greater. Sensors that are Repeater Ready will have a sticker that says, Firmware Release #4. The controller should have a sticker that says, Firmware Release #4. NOTES:

full controller replacement. in the sensors. If controllers firmware is less than that described above, then the controller will have to be upgraded. Either by firmware update or If the revision of the sensors is less than 4 (i.e. pre-existing sensors), then the controller must be upgraded to update the firmware MOUNTING NOTE: for best results mount the SiXRPTRA as high as possible, keeping it away from metal objects. 1. Select a mounting position for the module. IMPORTANT!

DO NOT mount on or inside a metal enclosure/object. DO NOT install near to WI-FI Routers, Microwave Oven and other interfering devices. Maintain at least 10 feet distance. 2. Attach to the wall using the supplied screws. 3. Install the center screw to secure the back tamper to the wall. 4. Ensure the wiring is complete. Use cable ties or staples as necessary to secure wiring. 5. Plug the power supply into an un-switched outlet and secure with screw. 6. Attach the backup battery wires. AC POWER The repeater is powered by a 5VDC, 1 Amp Plug-in Power Supply (Part #: 300-10342). Refer to the wiring table below for wire gauge and length:

Wire Gauge Wire Length

#22

#20

#18 Up to 20 feet (6m) Up to 33 feet (10m) Up to 50 feet (15m) Use only the 300-10259 Power Supply. Plug the battery prior to providing power from AC Outlet. NOTE: For Indoor Use Only. ENROLLING You must enroll the device in the controller. SiXRPTRA will attempt to auto enroll upon power up, if it times out you can press and release the tamper to reinitiate the enrollment process or remove and reconnect AC power. 1. Set the Controller in Programming Mode and when prompted:

2. Power up the SiXRPTRA and refer to the LED Status Table. NOTES:

Once enrolled in a system, the SiXRPTRA cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. Enrollment time varies depending on the signal strength between the device and the controller. When done, Power LED is ON for 3 seconds and the controller beeps to confirm enrollment. The SiXRPTRA should be installed before any other sensors. NOTE: Must be installed in accordance with the National Electrical Code, ANSI/NFPA 70 LED STATUS TABLE Green Amber Red RSSI Reliable Signal Marginal Signal, relocate No Signal (Slow Blinking) Power AC/Battery OK No Battery or Low Battery No AC, Running on Battery

(See note 3,4) RF Jamming OK, No Jamming N/A RF Jam Detected Enrolling (Green LEDs Only)

(Note 1) Enrollment Successful (Amber LEDs Only) Enrollment Time Out (Red LEDs Only) (Note 2) Normal Delete (Green LEDs Only) Self-Delete (Green LEDs Only) Programming NOTES:

Scrolling Scrolling Rapid Blink Rapid Blink Rapid Blink Rapid Blink Scrolling Scrolling Rapid Blink Rapid Blink Scrolling Scrolling Rapid Blink Rapid Blink Rapid Blink LED OFF X (Green, Red, or Amber) LED OFF 1. Cycle for scrolling Enrollment LED is 2 sec ON / 4 sec Off. 2. Blinking will continue for 5 seconds and then ALL LED's will go BLANK. 3. RED LED should be slow blinking (ON for 0.5 seconds; OFF for 3 seconds) 4. With the cover installed, the RSSI and RF Jamming LEDs will be off after 15 seconds. INSTALLING A NEW SiXRPTRA WITH AN EXISTING CONTROLLER AND SENSORS 1. Using the Compatibility Section above confirm the controller and sensors are at the correct revision level to support the SiXRPTRA. 2. Enroll the SiXRPTRA by keeping near the controller until all three LEDs are solid Green. The SiXRPTRA should be enrolled as a peripheral from MobileTech. 3. Walk the SiXRPTRA away from the controller in the direction in which the sensor(s) are not communicating with the controller. NOTE: Perform this step without the front cover installed to monitor the RSSI. 4. The SiXRPTRA verifies the signal strength between the controller and SiXRPTRA. The RSSI LED will change from Red to Amber (Green means you are within range) at least 30 seconds. Amber LED tells you this is the furthest from the controller you can mount the SiXRPTRA. 5. Perform SiX Auto System Check from MobileTech so the controller requests signal strength from all sensors. Once a sensor has joined the SiXRPTRA the signal strength should be greater than -75dBm. When a sensor is associated with a repeater, the displayed signal strength represents the connection quality between the sensor and the SiXRPTRA. 6. MobileTech or the Controller can tell you which the sensor is connected. On the controller go to zones to determine which it is connected to. Example: P800 represents the controller and R820 to R821 zones represents the SiXRPTRA. If sensors are not connected to the SiXRPTRA and connected to the controller and the signal strength is less than -75dBm, then the sensor has not connected to the repeater or it is still too far away from the controller/SiXRPTRA. If sensor signal strength is too weak then the controller can send a SiX Network Resync only to those sensors using MobileTech. This creates the best path between sensor and repeater. 7. Perform a Sensor Walk Test to verify sensors are communicating through the SiXRPTRA or directly to the controller. NOTE: Make sure all doors/windows are closed before entering Walk Test. MobileTech. INSTALLING A NEW SiXRPTRA WITH A NEW CONTROLLER AND SENSORS INSTALLATION 1. Using the Compatibility Section above confirm the controller and sensors are at the correct revision level to support the SiXRPTRA. 2. Enroll the SiXRPTRA by keeping near the controller until all three LEDs are solid Green. The SiXRPTRA should be enrolled as a peripheral from 3. Walk the SiXRPTRA away from the controller in the direction in which the sensor(s) are not communicating with the controller. NOTE: Perform this step without the front cover installed to monitor the RSSI. 4. The SiXRPTRA verifies the signal strength between the controller and SiXRPTRA every five seconds. The RSSI LED will change from Red to Amber (Green means you are within range) after 30 seconds. Amber LED tells you this is the furthest from the controller you can mount the SiXRPTRA. 5. Move the sensors to their predetermined mounting location. 6. Successfully enroll all sensors. 7. Perform SiX Auto System Check from MobileTech so the controller requests signal strength from all sensors. Once a sensor has joined the SiXRPTRA the signal strength should be greater than -75dBm. When a sensor is associated with a repeater, the displayed signal strength represents the connection quality between the sensor and the SiXRPTRA. 8. MobileTech or the Controller can tell you which the sensor is connected. On the controller go to zones to determine which it is connected to. Example: P800 represents the controller and R820 to R821 zones represents the SiXRPTRA. If sensors are not connected to the SiXRPTRA and connected to the controller and the signal strength is less than -75dBm, then the sensor has not connected to the repeater or it is still too far away from the controller/SiXRPTRA. If sensor signal strength is too weak then the controller can send a Sync Network Resync only to those sensors using MobileTech. This creates the best path between sensor and repeater. 9. Perform a Sensor Walk Test to verify sensors are communicating through the SiXRPTRA or directly to the controller. NOTE: Make sure all doors/windows are closed before entering Walk Test. 24-HOUR ENROLLMENT DELETION AND DEFAULT If the device is enrolled in a controller different than the intended controller, and you are unable to delete it from the unintended controller, default the device to factory default setting:

1. Open the cover and verify device is powered on. 2. Press the tamper for second, release for second and repeat four more times. (for a total of five). 3. All three LEDs rapidly flash and the SiXRPTRA defaults, leaving only the Power LED on. This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery installed). NOTE: if all LEDs light solid red for 5-seconds, then you are passed the 24-hour window. TAMPER/LOW BATTERY REPORTING The SiXRPTRA reports this condition to the Controller. If a low battery or tamper condition exists, a peripheral trouble shows a trouble on the Controller. NOTE: If an actual low battery condition is reported, it takes up to 12 hours after AC power is restored for the low battery restore message to be sent (requires 12 hours for fully recharged battery). IMPORTANT!

The first battery test occurs one hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within one minute. Also, the controller does not annunciate low battery trouble for the first 24 hours to all the battery to charge. The SiXRPTRA reports AC loss and RF jam conditions, which displays a trouble on the Controllers keypad(s). This prevents either condition from causing an alarm when the Controller is armed. SUPERVISION REPLACING THE BATTERY SPECIFICATIONS Voltage Transformer Part Number ............................................................................................................................................................ 300-10259 Input Voltage ...................................................................................................................................................... 100 ~ 240VAC, 50 ~60 Hz Operating Voltage ....................................................................................................................................................................... 5VDC (1A) Maximum Transformer Distance ........................................................................................................................... See Power Supply Table Battery ......................................................................................................................................................................................... 300-10342 Environmental Operating Temp .......................................................................................................................................... 14 F (-10C) to 140F (60C) NOTE: Charging the lithium battery stops when temperature is below 32F (0C) Relative Humidity ..................................................................................................... 95%, Non-condensing / 95%max. sans condensation Physical Dimensions .................................................................................. Length 6.9 in (175mm) / Width 4.4 in (113 mm) / Depth 1.2 in (31 mm) Conduit Insert ...................................................................................................................................................................... 1/2 in (12.7mm) Acceptable Cable Size ............................................................................................................................................................. 18 22AWG NOTE: System must also be tested with AC power removed. TEST SYSTEM WEEKLY REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. RF EXPOSURE Warning The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures. APPROVAL LISTINGS / APPROBATIONS HOMOLOGATIONS UL 985:2015 Ed.6+R:12Jul2018 UL 1023:2017 Ed.7 UL 1610:2016 Ed.4 UL 1637:2017 Ed.5 UL 2017:2008 Ed.2 +R:17Jan2016 ULC S304:2016 Ed.3 +R:10Oct2018 ULC S545:2002 Ed.2 ULC SUBJECT C1023:1974 Ed.1 CSA C22.2#205:2017 Ed.3 OTHER STANDARDS RoHS System shall be installed in accordance with CAN/ULC-S540, Residential Fire Warning Systems. System shall be installed in accordance with Chapter 29 of the National Fire Alarm and Signalling Code, ANSI/NFPA 72. System shall be installed in accordance with CSA C22.1, Canadian Electrical Code, Part I, Safety Standard for Electrical Installations; CAN/ULC S302, Standard for the Installation, Inspection and Testing of Intrusion Alarm Systems; and CAN/ULC S301, Standard for Signal Receiving Centre Intrusion Alarm Systems and Operations. FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, as defined by FCC Rules Part 15.105. The Class B Digital Device statement can be viewed at: https://customer.resideo.com/en-US/support/residential/codes-and-

standards/FCC15105/Pages/default.aspx FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dIndustrie Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. Responsible Party / Issuer of Suppliers Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive., Melville, NY 11747, Ph: 516-577-2000 The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health. Any attempt to reverse-engineer this device by decoding proprietary protocols, de-compiling firmware, or any similar actions is strictly prohibited. WARRANTY INFORMATION For the latest warranty information, please go to:

www.security.honeywellhome.com/warranty ADT Security Services 1501 Yamato Rd Boca Raton, FL 33431 800-24399-1A}

800-24399-1A 4/20 Rev A

Quick Installation Guide (English) The SiXRPTRA is an RF receiver and a transmitter and is intended to extend the indoor range of SiX series devices. The SiXRPTRA receives alarm, status, and control messages from SiX series devices, and forwards these messages to control panel. The control then responds accordingly (arm/disarm the system, initiate an alarm, etc.). FEATURES Transmits its own status, including wall and case tamper, AC loss, low battery, and RF Jam. Indicates RF Jam, AC/Battery Status, and RSSI (Received Signal Strength Indicator) using LEDs. RSSI indicates the signal condition between the repeater and the controller. Provides a 24-hour backup battery. ETL Listed to meet UL standards GENERAL GUIDELINES The SiXRPTRA module uses a 5VDC power supply to charge the battery. Power Supply Distance table:

Guide d'installation rapide Le SiXRPTRA est un rcepteur et un metteur RF et est destin tendre la porte intrieure des appareils de la srie SiX. Le SiXRPTRA reoit les messages d'alarme, d'tat et de contrle des appareils de la srie SiX et transmet ces messages au panneau de commande. Le panneau de commande rpond alors avec lordre appropri (armer/dsarmer le systme, dclencher une alarme, etc.). ATTRIBUTS Transmet son propre tat, notamment le vandalisme au botier ou au mur, la perte de courant alternatif, la dcharge de la pile et le brouillage RF. Indique une erreur RF, un tat c.a./pile et RSSI (indicateur de puissance du signal reu) l'aide de DEL. Le RSSI indique ltat du signal entre le rpteur et le contrleur. Fournit une pile de secours de 24 heures. Homologu ETL pour rpondre aux normes UL. DIRECTIVES GNRALES Le module SiXRPTRA utilise une alimentation 5 VCC pour charger la pile. Tableau des distances d'alimentation :

Wire Gauge 18 20 22 Wire Length Up to 50 feet (15m) Up to 33 feet (10m) Up to 20 feet (6m) Calibre du cble Longueur du cble 18 20 22 Jusqu 15 m (50 pieds) Jusqu 10 m (33 pieds) Jusqu 6 m (20 pieds) If the voltage drops to 3.6VDC a low battery will occur. NOTE: Anything lower than 2.6VDC, it is incapable of charging the battery; it must be replaced Conduct the SiX Auto System Check (see controllers instructions) to verify adequate signal strength, relocate if necessary. The SIXRPTRA is designed to operate 200 plus feet through 3 walls of wood, aluminum and dry wall construction. Si la tension baisse 3,6 Vc.c., une signalisation de pile faible sera mise. REMARQUE : moins de 2,6 Vc.c. de tension, il sera impossible de recharger la pile; elle devra tre remplace. Effectuer la vrification automatique du systme SiX (voir les instructions du contrleur) pour vrifier la puissance du signal; au besoin, le dplacer. Le SIXRPTRA pour fonctionner jusqu' plus de 60 m (200 pi) travers 3 murs de bois, d'aluminium et de construction de cloisons sches. SiXRPTRA Wireless Repeater / Rpteur sans fil / Repetidor inalmbrico Gua rpida de instalacin El SiXRPTRA es un receptor y transmisor de RF y est diseado para extender el rango en espacios interiores de los dispositivos de la serie SiX. El SiXRPTRA recibe mensajes de alarma, estado y control de los dispositivos de la serie SiX y los reenva al panel de control. Luego, el control responder segn corresponda

(armar/desarmar el sistema, iniciar una alarma, etc.). CARACTERSTICAS Transmite su propio estado, incluido el del seguro del gabinete y la pared, la prdida de CA, y la deteccin de batera baja e interferencias de RF. Indica la deteccin de interferencias de RF, el estado de CA/batera y el RSSI (indicador de intensidad de la seal recibida) utilizando luces LED. El indicador de fuerza de la seal recibida (RSSI) muestra el estado de la seal entre el repetidor y el controlador. Proporciona una batera de respaldo de 24 horas. Clasificacin ETL para cumplir con los estndares de UL INDICACIONES GENERALES El mdulo SiXRPTRA utiliza un suministro de alimentacin de 5 V de CC para cargar la batera. Tabla de distancia de la fuente de alimentacin:

Calibre del cable Longitud del cable 18 20 22 Hasta 15 m (20 pies) Hasta 10 m (33 pies) Hasta 6 m (20 pies) Si el voltaje cae a 3,6 VCC, la batera quedar baja. NOTA: Con cualquier unidad menor a 2,6 VCC, el dispositivo no podr cargar la batera, debe reemplazarse. Realice la comprobacin del sistema automtico de SiX (consulte las instrucciones del controlador) para verificar la intensidad adecuada de la seal y reubicarla si es necesario. El SIXRPTRA puede instalarse en un entorno residencial y est diseado para funcionar en un rango de 60 m (200 pies) o ms a travs de tres paredes de madera, aluminio y construcciones de paredes de yeso. NOTES:

COMPATIBILITY (REPEATER READY SYSTEM) All sensors (including keyfobs) connected to the Controller should have Firmware Release #4 or greater. Sensors that are Repeater Ready will have a sticker that says, Firmware Release

#4. The Controller should have a sticker that says, Firmware Release #4. If controllers firmware is less than that described above, the Controller must be updated. Either by firmware update or full controller replacement. If the revision of the sensors are less than 4 (i.e. pre-existing sensors), the Controller must be updated to update the firmware in the sensors. INSTALLING A NEW SiXRPTRA WITH AN EXISTING CONTROLLER AND SENSORS 1. Using the Compatibility Section above confirm the controller and sensors are at the correct revision level to support the SiXRPTRA. 2. Enroll the SiXRPTRA. See Enrolling section below. 3. Walk the SiXRPTRA away from the controller in the direction in which the sensor(s) are not communicating with the controller. NOTE: Perform this step without the front cover installed to monitor the RSSI. 4. The SiXRPTRA verifies the signal strength between the controller and SiXRPTRA every five seconds. The RSSI LED will change from Red to Amber (Green means you are within range) after 30 seconds. Amber LED tells you this is the furthest from the controller you can mount the SiXRPTRA. 5. Perform SiX Auto System Check from MobileTech so the Controller requests signal strength from all sensors. Once a sensor has joined the SiXRPTRA the signal strength should be at least -75dBm. 6. MobileTech or the Controller can tell you which the sensor is connected. On the controller go to zones to determine which it is connected to. Example: P800 represents the controller and R820 to R821 zones represents the SiXRPTRA. If sensors are not connected to the SiXRPTRA and connected to the controller and the signal strength is less than -75dBm, then the sensor has not connected to the repeater or it is still too far away from the controller/SiXRPTRA. If sensor signal strength is too weak then the controller can send a SiX Network Sync only to those sensors using MobileTech. 7. Perform a Sensor Walk Test to verify sensors are communicating through the SiXRPTRA or directly to the Controller. NOTE: Make sure all doors/windows are closed before entering Walk Test. COMPATIBILIT (SYSTME PRT POUR RPTEUR) Tous les capteurs (y compris les tlcommandes) connects au contrleur doivent avoir une version de micrologiciel de version n 4 ou suprieure. Les capteurs Prt pour rpteur auront un autocollant indiquant Version 4 du micrologiciel . Le contrleur doit avoir un autocollant qui dit, Version 4 du micrologiciel . REMARQUES :

si le micrologiciel du contrleur est infrieur celui dcrit ci-dessus, le contrleur devra tre mis niveau. Soit par mise jour du micrologiciel ou remplacement complet du contrleur. COMPATIBILIDAD (SISTEMA PREPARADO PARA EL REPETIDOR) Todos los sensores (incluidos los llaveros de control remoto) conectados al Controlador deben tener la versin de Firmware #4 o superior. Los sensores que estn preparados para el repetidor tendrn una etiqueta que diga Versin de firmware nro. 4. El controlador debe tener una etiqueta que diga Versin de firmware n. 4. NOTAS:

Si el firmware del controlador es inferior al descrito anteriormente, el controlador debe actualizarse. Ya sea mediante la actualizacin del firmware o el reemplazo completo del controlador. Si la rvision des capteurs est infrieure 4 (c'est--dire les capteurs prexistants), le contrleur devra tre mis Si la revisin de los sensores son menos de 4 (es decir, sensores preexistentes), el controlador debe niveau pour mettre jour le micrologiciel des capteurs. actualizarse para actualizar el firmware en los sensores. INSTALLATION D'UN NOUVEAU SIXRPTRA AVEC UN CONTRLEUR ET DES CAPTEURS EXISTANTS 1. En utilisant la Section de compatibilit ci-dessus, confirmez que le contrleur et les capteurs sont au niveau de rvision correct pour prendre en charge le SiXRPTRA. 2. Enregistrer le SiXRPTRA. Voir la section Inscription ci-dessous. 3. loignez le SiXRPTRA du contrleur dans la direction dans laquelle le ou les capteurs ne communiquent pas avec le contrleur. REMARQUE : Excutez cette tape sans que le couvercle avant soit install pour surveiller le RSSI. 4. Le SiXRPTRA vrifie la puissance du signal entre le contrleur et le SiXRPTRA toutes les cinq secondes. Le voyant RSSI passera du rouge ambre (le vert signifie que vous tes porte) aprs 30 secondes. Le voyant ambre vous indique que cest le plus loign du contrleur o vous pouvez installer le SiXRPTRA. INSTALAR UN SIXRPTRA NUEVO CON UN CONTROLADOR Y SENSORES EXISTENTES 1. El uso de la "Seccin de compatibilidad" anterior confirma que el controlador y los sensores se encuentran en el nivel de revisin correcto para ser compatibles con el SiXRPTRA. 2. Registre el SiXRPTRA. Consulte la seccin Registro a continuacin. 3. Aleje el SiXRPTRA del controlador en la direccin en la que los sensores no se comuniquen con el controlador. NOTA: Lleve a cabo este paso sin la tapa frontal instalada para monitorear el RSSI. 4. El SiXRPTRA verifica la intensidad de la seal entre el controlador y el SiXRPTRA cada cinco segundos. El LED del RSSI cambiar de rojo a mbar (el verde significa que est dentro del rango) despus de 30 segundos. El LED mbar le indica que es lo ms alejado del controlador que puede colocar el SiXRPTRA. 5. Excutez la Vrification du systme SiX automatique de MobileTech pour que le contrleur demande la 5. Realice la verificacin automtica del sistema SiX Auto System Check desde MobileTech para que el puissance du signal tous les capteurs. Une fois qu'un capteur a rejoint le SiXRPTRA, la puissance du signal doit tre suprieure -75 dBm. controlador solicite la intensidad de la seal de todos los sensores. Una vez que un sensor se ha unido al SiXRPTRA, la intensidad de la seal debera ser superior a -75dBm. 6. MobileTech ou le contrleur peuvent vous dire quel capteur est connect. Sur le contrleur, allez dans les zones 6. MobileTech o el Controller le pueden indicar qu sensor est conectado. En el controlador, dirjase a las zonas pour dterminer celui sur lequel il est connect. Exemple : P800 reprsente le contrleur et les zones R820 R821 reprsentent le SiXRPTRA. Si les capteurs ne sont pas connects au SiXRPTRA et connects au contrleur et que la puissance du signal est infrieure -75 dBm, alors le capteur ne s'est pas connect au rpteur ou il est encore trop loin du contrleur/SiXRPTRA. Si la puissance du signal du capteur est trop faible, le contrleur peut envoyer la commande Synchroniser le rseau SiX uniquement aux capteurs utilisant MobileTech. para determinar a qu est conectado. Ejemplo: P800 representa el controlador y las zonas R820 a R821 representan el SiXRPTRA. Si los sensores no estn conectados al SiXRPTRA y estn conectados al controlador y la intensidad de la seal es inferior a -75dBm, quiere decir que el sensor no se ha conectado al repetidor o sigue estando demasiado alejado del controlador/SiXRPTRA. Si la intensidad de la seal del sensor es demasiado dbil, el controlador puede enviar una sincronizacin de la red de SiX (SiX Network Sync) solo a aquellos sensores usando MobileTech. 7. Effectuez un test de marche des capteurs pour vrifier que les capteurs communiquent par le biais 7. Realice una prueba de caminata de los sensores (Sensor Walk Test) para verificar que los sensores se estn du SiXRPTRA ou directement avec le contrleur. REMARQUE : Assurez-vous que toutes les portes/fentres sont fermes avant de commencer le test de marche. comunicando por medio de SiXRPTRA o directamente al controlador. NOTA: Asegrese de que todas las puertas y ventanas estn cerradas antes de comenzar la prueba. INSTALLING A NEW SiXRPTRA WITH A NEW CONTROLLER AND SENSORS INSTALLATION 1. Follow step two through four above. 2. Move the sensors to their predetermined mounting location. 3. Successfully enroll all sensors. 4. Follow step five through seven above to determine optimal repeater location. INSTALLATION D'UN NOUVEAU SIXRPTRA AVEC UNE NOUVELLE INSTALLATION DE CONTRLEUR ET DE CAPTEURS 1. Suivez les tapes deux quatre ci-dessus. 2. Dplacez les capteurs vers leur emplacement d'installation prdtermin. 3. Inscrire tous les capteurs avec succs. 4. Suivez les tapes cinq sept ci-dessus pour dterminer l'emplacement optimal du rpteur INSTALACIN DE UN SiXRPTRA NUEVO CON INSTALACIN DE SENSORES Y UN CONTROLADOR NUEVO 1. Siga los pasos dos a cuatro anteriores. 2. Mueva los sensores a su ubicacin de montaje predeterminada. 3. Registre correctamente todos los sensores. 4. Siga del paso 5 hasta el 7 de los anteriores para determinar la ubicacin ideal del repetidor. MOUNTING NOTE: for best results mount the SiXRPTRA as high as possible, keeping it away from metal objects. 1. Select a mounting position for the module. NOTE: DO NOT mount on or inside a metal enclosure/object. Or, near Wi-Fi Routers, Microwave Oven and other interfering devices. Maintain at least 10 feet distance. Do Not Connect to a receptacle controlled by a switch. Install the center screw to secure the back tamper to the wall. 2. Attach to the wall using the supplied screws. 3. 4. Ensure the wiring is complete. Use cable ties as necessary to secure wiring. 5. Plug the power supply into an un-switched outlet and secure with screw. 6. Attach the backup battery. ENROLLING You must enroll the device in the control. SIXRPTRA will attempt to auto enroll upon power up, if it times out you can press and release the tamper to reinitiate the enrollment process or remove and reconnect AC power. NOTE: Once enrolled in a system, the SiXRPTRA cannot be used with another Controller until it is removed from the current controller. See the Controllers instructions for details. Refer to the LED Status Table for the operation of the LEDs during enrollment. Keep near the Controller until all three LEDs are solid green. MONTAGE REMARQUE : Pour de meilleurs rsultats, montez le SiXRPTRA le plus haut possible, en le tenant loign des objets mtalliques. 1. Slectionnez une position de montage pour le module. MONTAJE NOTA: Para obtener mejores resultados, coloque el SiXRPTRA lo ms alto posible y mantngalo alejado de los objetos metlicos.. 1. Seleccione una posicin de montaje para el mdulo. REMARQUE : NE PAS monter sur ou l'intrieur d'un botier/objet mtallique. Ou, proximit d'un routeur WI-FI, d'un four micro-ondes et d'autres appareils produisant de l'interfrence. Maintenir une distance d'au moins 3 m (10 pi). Ne branchez pas le transformateur une prise contrle par un interrupteur. Fixer au mur l'aide des vis fournies. Installer la vis centrale pour fixer lantisabotage arrire au mur. 2. 3. 4. Veillez ce que le cblage soit complt. Au besoin, placer des attaches-cbles pour fixer le cblage. 5. Brancher le bloc dalimentation dans une prise non contrls par un interrupteur, puis le fixer laide dune vis. 6. Fixer la pile de secours. ENREGISTREMENT Vous devez enregistrer l'appareil dans le contrleur. SiXRPTRA tentera de s'inscrire automatiquement lors de sa mise sous tension, si le dlai expire, vous pouvez appuyer et relcher le bouton de sabotage pour relancer le processus d'inscription ou dbrancher et rebrancher le courant alternatif. REMARQUE : Une fois enregistr dans un systme, le SiXRPTRA ne peut pas tre utilis avec un autre contrleur tant quil na pas t retir du contrleur actuel. Pour plus de dtails, consulter les instructions du contrleur. Reportez-vous au tableau d'tat des DEL pour le fonctionnement des DEL pendant l'inscription. Restez prs du contrleur jusqu' ce que les trois DEL soient vertes en continu. NOTA: NO lo monte sobre ni dentro de un recinto u objeto metlico. Tampoco cerca de routers Wi-Fi, hornos de microondas y otros dispositivos que produzcan interferencias. Mantenga una distancia mnima de 3 metros (10 pies). No se lo debe conectar a un tomacorriente controlado por un interruptor. 2. Fjelo a la pared con los tornillos suministrados. 3. 4. Asegrese de que el cableado est completo. Utilice las bridas para cables que considere necesarias Instale el tornillo central para asegurar la parte posterior del seguro a la pared. para asegurar el cableado. 5. Enchufe el suministro de alimentacin a un enchufe sin conexin y asegrelo con un tornillo. 6. Una la batera de respaldo. REGISTRO Debe registrar este dispositivo en el control. El SiXRPTRA intentar registrarse automticamente al encenderse; si se agota el tiempo, puede presionar y soltar el seguro para reiniciar el proceso de registro o desconectar y reconectar la alimentacin de CA. NOTA: Una vez registrado en el sistema, el SiXRPTRA no puede usarse con otro controlador hasta que se retire del controlador actual. Consulte las instrucciones del controlador para obtener ms informacin. Consulte la tabla de estado del LED para chequear la operacin del LED durante el registro. Mantngase cerca del controlador hasta que los tres LED se enciendan por completo en verde. NOTE: For Indoor Use Only REMARQUE : Pour montage interne seulement. NOTA: nicamente para uso interior. NOTE: Must be installed in accordance with the National Electrical Code, ANSI/NFPA 70 REMARQUE : Le dispositif doit tre install conformment au National Electrical Code des tats-Unis, et la norme ANSI/NFPA 70. NOTA: Debe instalarse de acuerdo con el Cdigo Elctrico Nacional, ANSI/NFPA 70 Figure 1. Mounting the Repeater / Installation du rpteur / Montaje del repetidor 24-HOUR ENROLLMENT DELETION AND DEFAULT If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended panel, default the device to factory default setting:

1. Open the cover and verify device is powered on. 2. Press the tamper for second, release for second and repeat four more times. (for a total of five). 3. All three LEDs rapidly flash and the SiXRPTRA defaults, leaving only the Power LED on. This procedure is available for 24 hours after enrollment with a panel and the device remains powered

(battery installed). NOTE: If all LEDs light solid red for 5 seconds, then you are passed the 24-hour window. SUPERVISION The SiXRPTRA reports AC loss and RF jam conditions, which displays a trouble on the Controllers keypad(s). This prevents either condition from causing an alarm when the Controller is armed. TAMPER/LOW BATTERY REPORTING The SiXRPTRA reports this condition to the Controller. If a low battery or tamper condition exists, a peripheral trouble shows a trouble on the Controller. NOTE: If an actual low battery condition is reported, it takes up to 12 hours after AC power is restored for the low battery restore message to be sent (requires 12 hours for fully recharged battery). IMPORTANT: The first battery test occurs 1-hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within 1-minute. Also, the controller does not annunciate low battery trouble for the first 24 hours to all the battery to charge. Figure 2. Electrical Connections / Connections lectriques / Conexiones elctricas SUPPRESSION PAR DFAUT MANUEL APRS 24 HEURES DE L'INSCRIPTION Si le priphrique est enregistr dans un panneau autre que celui pour lequel il est destin, et que vous ne parvenez pas le supprimer du mauvais panneau, rinitialisez le priphrique ses paramtres dusine par dfaut :

1. Ouvrez le couvercle et assurez-vous que le priphrique est sous tension. 2. Appuyez sur le bouton sabotage pendant seconde, relchez-le pendant seconde et rptez quatre fois. (pour un BORRADO DE REGISTRO Y RESTAURACIN A VALOR PREDETERMINADO DE 24 HORAS Si el dispositivo est registrado en un panel diferente al previsto y no puede eliminarlo del panel no deseado, restablezca el dispositivo a la configuracin predeterminada de fbrica:

1. Abra el cobertor y verifique que el dispositivo est encendido. 2. Presione el seguro durante segundo, libere durante segundo y repita cuatro veces ms. (cinco 3. Les trois DEL clignotent rapidement et le SiXRPTRA revient aux valeurs par dfaut, ne laissant que 3. Los tres LED pestaean rpidamente y el SiXRPTRA se restablece, y deja solo el LED de energa total de cinq). le voyant d'alimentation allum. veces en total). encendido. Cette procdure est disponible durant 24 heures aprs lenregistrement sur un panneau et avec un priphrique aliment (pile installe). REMARQUE : Si toutes les DEL sont allumes en rouge continu pendant 5 secondes, vous avez dpass la plage de 24 heures. SURVEILLANCE Le SiXRPTRA signale les conditions de perte CA et de brouillage RF, ce qui affiche un problme sur le (s) clavier (s) du contrleur. De cette faon, aucune de ces conditions ne provoquera dalarme durant larmement du panneau de commande. SIGNALISATION DE SABOTAGE/PILE FAIBLE Le SiXRPTRA signale cette condition au contrleur. En cas de pile faible ou de sabotage, un problme priphrique sera indiqu sur le contrleur. REMARQUE : Si un tat de pile faible est signal, il peut scouler jusqu 12 heures entre la restauration de lalimentation CA et lenvoi du message de restauration de la pile (ncessite 12 heures pour recharger compltement la pile). IMPORTANT : Le premier test de la pile est men 1 heure aprs la mise sous tension. Pour vrifier rapidement le bon tat dune pile de secours, dbranchez, puis rebranchez le bloc dalimentation; le systme effectuera un test de la pile dans la minute qui suit. De plus, le contrleur n'annonce pas les problmes de pile faible pendant les 24 premires heures pour permettre la pile d'tre totalement charge. Este procedimiento se encuentra disponible durante 24 horas despus del registro con un panel y el dispositivo permanece encendido (batera instalada). NOTA: Si todos los LED se encienden en rojo slido durante 5 segundos, ya se cumpli la ventana de 24 horas. SUPERVISIN El SiXRPTRA informa sobre las condiciones de prdida de CA y de deteccin de interferencias de RF, lo que muestra un problema en los teclados del controlador. Esto impide que cualquiera de las dos condiciones genere una alarma cuando se arma el controlador. INFORME DE SEGURO/BATERA BAJA El SiXRPTRA informa esta condicin al controlador. Si existe una condicin de batera baja o seguro, un problema perifrico muestra un problema en el controlador. NOTA: Si se informa un estado real de baja batera, pasarn hasta 12 horas despus de la restauracin de alimentacin de CA antes de que se enve el mensaje de restauracin de batera baja (requiere 12 horas de batera completamente cargada). IMPORTANTE: La primera prueba de la batera se realiza 1 hora despus del encendido. Para verificar rpidamente una buena batera de respaldo, desenchufe y enchufe nuevamente el suministro de energa; el sistema realizar la prueba de batera en 1 minuto. Adems, el controlador no anuncia el problema de batera baja durante las primeras 24 horas a toda la batera para cargarla. LED STATUS TABLE / TABLEAU D'TAT DES DEL / TABLA DE ESTADO DEL LED Green / Verte / Verde Amber / Ambre / Amber Red / Rouge / Rojo RSSI / RSSI / RSSI Power / Alimentation./ Alimentacin RF Jamming / Brouillage RF / Deteccin de interferencias de RF Reliable Signals/ Signaux fiables / Seales fiables AC Powered/ Sous tension c.a. / Alimentacin de CA No Battery or Low Battery / Pas de pile ou pile faible / Sin batera o batera baja OK, No RF Jamming / OK, pas de brouillage RF / Buen estado, sin deteccin de interferencias de RF N/A / S. O / N/A No Ac, Running on Battery (see note 3,4) / Pas de c.a., fonctionnement sur pile

(voir remarque 3,4) / Sin CA, funcionando con batera (ver nota 3,4) RF Jam Detected / Brouillage RF dtect / Interferencias de RF detectadas Marginal Signal (relocate) / Signal marginal, relocaliser / Seal deficiente (reubicar) No Signal (Slow Blinking) / Aucun signal (Clignotement lent)

/ Sin seal (Parpadeo lento) Enrolling (Green LEDs Only) (Note 1) / Inscription (DEL vertes uniquement) (remarque 1) /

Registro (solo LED verde) (Nota 1) Enrollment Successful (Amber LEDs Only) / Inscription russie (DEL ambre uniquement) /

Registro satisfactorio (solo LED mbar) Enrollment Time Out (Red LEDs Only) (Note 2) / Dlai dinscription expir (DEL rouges uniquement) (remarque 2) / Expiracin de tiempo de registro (solo LED rojoNota 2) Normal Delete (Green LEDs Only) / Suppression normale (DEL vertes uniquement) /

Borrado normal (solo LED verde) Self-Delete (Green LEDs Only) / Auto-suppression (DEL vertes uniquement) / Borrado automtico (solo LED verde) Scrolling / Dfilement / Desplazamiento Scrolling / Dfilement / Desplazamiento Scrolling / Dfilement / Desplazamiento Scrolling / Dfilement / Desplazamiento Scrolling / Dfilement / Desplazamiento Scrolling / Dfilement / Desplazamiento Rapid Blink / Clignotement rapide / Parpadeo rpido Rapid Blink / Clignotement rapide / Parpadeo rpido Rapid Blink / Clignotement rapide / Parpadeo rpido Rapid Blink / Clignotement rapide/ Parpadeo rpido Rapid Blink / Clignotement rapide / Parpadeo rpido Rapid Blink / Clignotement rapide / Parpadeo rpido Rapid Blink / Clignotement rapide/ Parpadeo rpido Rapid Blink / Clignotement rapide / Parpadeo rpido Rapid Blink / Clignotement rapide / Parpadeo rpido Programming / Programmation / Programacin NOTES / REMARQUES./ NOTES / :

1. Cycle for scrolling Enrollment LED is 2 sec ON/ 4 sec Off. / Le cycle de dfilement du voyant d'inscription est allum 2 s/teint 4 s.. / El ciclo para desplazar el registro LED es 2 segundos ON/Encendido y 4 segundos Off/apagado. 2. Blinking will continue for 5 seconds and then ALL LED's will go BLANK. / Le clignotement se poursuivra durant 5 secondes, puis TOUTES les DEL S'TEINDRONT. / El parpadeo continuar durante 5 segundos y luego TODOS los indicadores LED quedarn sin color. 3. RED LED should be slow blinking (ON for 0.5 seconds, OFF for 3 seconds) / La DEL ROUGE doit clignoter lentement (allume pendant 0,5 seconde; teinte pendant 3 secondes) / El LED ROJO debera parpadear lentamente (encendido durante 0,5 segundos, apagado durante 3 segundos) 4. With the cover installed, the RSSI and RF Jamming LEDs will be off after 15 seconds. / Une fois le couvercle install, les voyants de brouillage RSSI et RF steignent au bout de 15 secondes. / Con la cubierta instalada, el RSSI y los LED de interferencia de RF se apagarn despus de 15 segundos. X (Green, Amber, or Red) / X (vertes, ambres ou rouges / X (verde, mbar o rojo) LED OFF / DEL TEINTES / LED APAGADO LED OFF / DEL TEINTES / LED APAGADO BATTERY / PILE / BATERA SPECIFICATIONS / FICHE TECHNIQUE / ESPECIFICACIONES Voltage / Tension / Voltaje Transformer Part # / N de pice du transformateur # / Pieza de transformador # .......................................................................................................................................................................................... 300-10259 Input Voltage / Tension d'entre / Voltaje de entrada .............................................................................................................................................................................................................. 100 ~ 240VAC, 50 ~60 Hz Operating Voltage / Tension de service / Voltaje de funcionamiento ............................................................................................................................................................................................................... 5VDC (1A) Maximum Transformer Distance / Distance maximale du transformateur / Distancia mxima del transformador ...................................................................................................... See Power Supply Distance Table

................................................................................................................................................................................................................................................................... Voir le Tableau des distances d'alimentation

......................................................................................................................................................................................................................................................... Ver la tabla de distancia de fuente de alimentacin Battery/ Pile / Bateria ................................................................................................................................... P/N 300-10342 Rechargeable Backup Battery: Lithium ion battery pack rated at 3.6/4.2V, 2480 mAH

................................ ............................... ............................... ............................ P/N 300-10342 Pile de secours rechargeable : Bloc-pile au lithium-ion de tension nominale de 3,6 4,2 Vde 2 480 mAH

................................ ............................... ............................... ............................... .............. P/N 300-10342 Batera de respaldo recargable: Paquete de batera de iones de litio de 3,6/4,2V, 2480 mAH Environmental /Conditions ambiantes / Ambiente Operating Temperature / Temprature de fonctionnement / Temperatura de funcionamiento ......................................................................................................................................... 14 F (-10C) to 140F (60C) NOTE: Charging the lithium battery stops when temperature is below 32F (0C) / NOTE: la recharge de la pile cesse lorsque la temprature tombe sous 0C (32F) / )/NOTE: La carga de la batera de litio se detiene cuando la temperatura es menor a 32F (0C) Relative Humidity / Humidit relative / Relative Humidity .................................................................................................................... 95%, Non-condensing / 95 % max. sans condensation / 95 %, sin condensacin Physical / Physique / Condiciones fsicas Dimensions / Dimensions / Dimensiones ............................................................................................................................................................................................ Length / Longueur / Longitud 6.9 in (175 mm) x

.................................................................................................................................................................................................................................................................... Width / Largeur / Ancho 4.4 in (113 mm) x

......................................................................................................................................................................................................................................................... Depth / Profondeur / Profundidad 1.2 in (31 mm) Conduit Insert / Insertion de conduit / Insercin de conducto .................................................................................................................................................................................................................. 1/2 in (12.7mm) Acceptable Cable Size / Calibre de conducteurs acceptable / Tamao de cable aceptable ......................................................................................................................................................................... 18 22AWG REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. POUR LES LIMITES DU SYSTME DALARME AU COMPLET, REPORTEZ-VOUS AU GUIDE DINSTALLATION DU PANNEAU DE COMMANDE CONSULTE LAS INSTRUCCIONES DE INSTALACIN PARA EL CONTROLADOR CON EL CUAL SE UTILIZA ESTE DISPOSITIVO, PARA OBTENER DETALLES CON RESPECTO A LAS LIMITACIONES DE TODO EL SISTEMA DE ALARMA. FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, as defined by FCC Rules Part 15.105. The Class B Digital Device statement can be viewed at:

https://customer.resideo.com/en-US/support/residential/codes-and-standards/FCC15105/Pages/default.aspx FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. DECLARACIONES DE LA COMISIN FEDERAL DE COMUNICACIONES E INDUSTRY CANADA El usuario no efectuar ningn cambio ni modificacin al equipo, a menos que estuviera autorizado en las Instrucciones de instalacin o en el Manual del usuario. Las modificaciones o cambios no autorizados pueden anular la autoridad del usuario para operar el equipo. DISPOSITIVO DE DISPOSITIVO DIGITAL DE CLASE B Este equipo ha sido probado y se encontr que cumple con los lmites para un dispositivo digital de Clase B, como se define en la Parte 15.105 de las Normas de la FCC. La declaracin del dispositivo digital de Clase B se puede ver en:

https://customer.resideo.com/en-US/support/residential/codes-and-standards/FCC15105/Pages/default.aspx DCLARATION DE LA FCC ET IC Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence rss dindustrie canada. Son fonctionnement est soumis aux conditions suivantes: (1) cet appareil ne doit pas causer dinterfrences nuisibles. (2) cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. DECLARACIONES DE LA FEDERAL COMMUNICATIONS COMMISSION (COMISIN FEDERAL DE COMUNICACIONES, FCC) Y DE INDUSTRY CANADA (MINISTERIO DE INDUSTRIA DE CANAD, IC) El usuario no efectuar ningn cambio ni modificacin en el equipo, a menos que cuente con la autorizacin que otorgan las instrucciones de instalacin o el Manual del usuario. Las modificaciones o cambios no autorizados pueden anular la autoridad del usuario para operar el equipo. DECLARACIN DE DISPOSITIVO DIGITAL CLASE B Este equipo se prob y cumple con los lmites de un dispositivo Clase B, conforme a la parte 15.105 de las Reglas de la FCC. La declaracin de dispositivos digitales clase B se puede encontrar en el siguiente enlace:

https://customer.resideo.com/en-US/support/residential/codes-and-standards/FCC15105/Pages/default.aspx DECLARACIN DE FCC/IC Este dispositivo cumple con la Parte 15 de las Reglas de la FCC y con los RSS exentos de licencia de Industry Canada. El funcionamiento est sujeto a las siguientes dos condiciones: (1) Este dispositivo no provoca ninguna interferencia perjudicial, y (2) Este dispositivo aceptar cualquier interferencia que reciba, incluida una interferencia que pueda provocar un funcionamiento no deseado. Responsible party / issuer of suppliers declaration of conformity: Ademco inc., a subsidiary of Resideo Technologies, inc., 2 Corporate Center Drive., Melville, NY 11747, PH: 516-577-2000 Partie responsable / metteur de la dclaration de conformit du fournisseur : Ademco inc., une filiale de Resideo Technologies, inc., 2 Corporate Center Drive., Melville, NY 11747, PH: 516-577-2000 Parte responsable / Emisor de la Declaracin de conformidad del proveedor: Ademco Inc., una subsidiaria de Resideo Technologies, Inc., 2 Corporate Center Drive., Melville, NY 11747, Ph: 516-

577-2000 NOTE: SYSTEM MUST ALSO BE TESTED WITH AC POWER REMOVED. TEST SYSTEM WEEKLY REMARQUE : LE SYSTME DOIT GALEMENT TRE TEST SANS ALIMENTATION EN TESTER LE SYSTME DE FAON HEBDOMADAIRE NOTA: EL SISTEMA TAMBIN DEBE PROBARSE CON LA ALIMENTACIN DE CA PRUEBE EL SISTEMA CADA SEMANA COURANT ALTERNATIF. DESCONECTADA DECLARACIN IFETEL La operacin de este equipo est sujeta a las siguientes dos condiciones 1. Es posible que este equipo o dispositivo no cause interferencia perjudicial y 2. Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada Approval Listings / Approbations Homologations / Listas de aprobaciones:

UL 985:2015 Ed.6+R:12Jul2018 UL 1023:2017 Ed.7 UL 1610:2016 Ed.4 UL 1637:2017 Ed.5 UL 2017:2008 Ed.2 +R:17Jan2016 ULC S304:2016 Ed.3 +R:10Oct2018 ULC S545:2002 Ed.2 ULC SUBJECT C1023:1974 Ed.1 CSA C22.2#205:2017 Ed.3 Other Standards / Autres normes: RoHS System shall be installed in accordance with CAN/ULC-S540, Residential Fire Warning Systems. System shall be installed in accordance with Chapter 29 of the National Fire Alarm and Signalling Code, ANSI/NFPA 72. System shall be installed in accordance with CSA C22.1, Canadian Electrical Code, Part I, Safety Standard for Electrical Installations; CAN/ULC S302, Standard for the Installation, Inspection and Testing of Intrusion Alarm Systems; and CAN/ULC S301, Standard for Signal Receiving Centre Intrusion Alarm Systems and Operations. The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health. Any attempt to reverse-engineer this device by decoding proprietary protocols, de-compiling firmware, or any similar actions is strictly prohibited. The Honeywell Home Trademark is used under license from Honeywell International Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates. For Technical Support, call 1-877-748-7628, option 3 For documentation, call Customer Service at:

1-800-238-2727 (1-800-ADT-ASAP). U.S. warranty www.security.honeywellhome.com/warranty Le dispositif doit tre install conformment la norme CAN/ULC-S540 (Residential Fire Warning Systems) Systmes de dtection dincendie dans les btiments rsidentiels. Le dispositif doit tre install conformment au chapitre 29 du Code national dalarme et de signalisation dincendie, ANSI/NFPA 72. Le dispositif doit tre install conformment la norme CSA C22.1, Code canadien de llectricit, 1re partie : norme de scurit relative aux installations lectriques ; CAN/ULC S302, Norme pour linstallation, linspection et le test de systmes dalarme effraction ; et CAN/ULC S301, Norme pour les systmes dalarme effraction des centres de rception de signaux et leur fonctionnement. El sistema se instalar de acuerdo con el CAN/ULC-S540, Sistemas residenciales de alerta contra incendios. El sistema se instalar de acuerdo con el captulo 29 del Cdigo Estadounidense de Alarma y Sealizacin de Incendios, ANSI/NFPA 72. El sistema se instalar de conformidad con el CSA C22.1, Cdigo de Electricidad Canadiense, Parte I, Norma de Seguridad para Instalaciones Elctricas, CAN/ULC S302, Normativa para la Instalacin, Inspeccin y Prueba de Sistemas de Alarma de Intrusin, y CAN/ULC S301, Normativa para los Sistemas y Operaciones de Alarma de Intrusin del Centro de Recepcin de Seales. Ce produit ne doit pas tre jet avec les ordures mnagres. Recherchez les centres de collecte ou de recyclage autoriss les plus prs de chez vous. Llimination adquate dquipement en fin de vie permet dviter les consquences nfastes sur lenvironnement et sur la sant humaine. El producto no debera desecharse junto con otros residuos domsticos. Busque los centros de recoleccin autorizados o de reciclaje autorizados ms cercanos. La eliminacin correcta del equipamiento al final de su vida til ayudar a prevenir posibles consecuencias negativas para el medio ambiente y la salud humana. Toute tentative dingnierie inverse de cet appareil,en dcodant les protocoles propritaires, en dcompilant le logiciel microprogramme ou en effectuant toute mesure similaire est strictement interdite. La Honeywell Home est une marque de commerce de Honeywell International inc. utilise sous licence par Resideo Technologies, inc. Ce produit a t fabriqu par Resideo Technologies, Inc. et ses filiales. Est estrictamente prohibido intentar aplicar ingeniera inversa a este dispositivo al decodificar los protocolos de propiedad exclusiva, descompilar firmware o hacer acciones similares. La marca Honeywell Home se utiliza bajo licencia de Honeywell International Inc. Este producto es fabricado por Resideo Technologies, Inc. y sus afiliados. Para Soporte Tcnico, llame al 1-877-748-7628, opcin 3 Para documentacin, llame a Servicio al Cliente a:

1-800-238-2727 (1-800-ADT-ASAP) U.S. Garantie www.security.honeywellhome.com/warranty Pour le support technique, appelez 1-877-748-7628, option 3. Pour la documentation, appelez le service clientle au 1-800-238-2727 (1-800-ADT-ASAP). U.S. Garantie www.security.honeywellhome.com/warranty ADT Security Services 1501 Yamato Rd Boca Raton, FL 33431 800-24400-1AR 800-24400-1A 4/20 Rev A

CFS8DL6RPTA / 573F-6RPTA EXHIBIT 8 Label Information LABEL INFORMATION EXACT LOCATION OF THE LABEL:

Label is located on the right side of the inside plastic case cover in the location shown:

FCC/IC IDs Location Page 1 of 2 EXHIBIT 8 Label Information CFS8DL6RPTA / 573F-6RPTA LABEL Page 2 of 2

2 Corporate Center Drive Melville, NY 11747 516-577-2000 CFS8DL6RPTA FCC COVER LETTER Date: 07/16/2020 To Whom It May Concern:

This letter is to inform you of our request for a new certification for our transceiver known as CFS8DL6RPTA. The transceiver will operate under Part 15.247. Regards, X Michael Antola

2 Corporate Center Drive Melville, NY 11747 516-577-2000 Request for Confidentiality Date: 07/16/20 Subject: Confidentiality Request for: CFS8DL6RPTA Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 9.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Permanent Permanent*1 Short Term Permanent Short Term Short Term Short Term Short Term Short Term Permanent Permanent Permanent Permanent*3 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation

(Including both Functional Descriptions and Detailed Message Timing & Duty Factor Info) Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual Ademco Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify UL LLC in the event information regarding the product or the product is made available to the public. UL LLC will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By:

(Signature/Title2)

/ Hardware Engineer Michael Antola

(Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.