FCC ID: CFS8DL6RPT Wireless SiX Security Repeater

SiXREPEATER Wireless Repeater INSTALLATION INSTRUCTIONS The Honeywell SiXREPEATER is an RF receiver/transmitter intended to extend the range of Honeywells SiX series devices by 200 feet (nominal range). The SiXREPEATER receives alarm, status, and control messages from SiX series devices. Once received, it forwards these messages to controller. The controller then responds accordingly (arm/disarm the system, initiate an alarm, etc.). FEATURES Transmits its own status, including tamper, AC loss, and RF Jam. Status sent when any change occurs or during the one hour supervisory check in. Provides a 24-hour backup rechargeable battery. Features a Spatial Diversity system that virtually eliminates the possibility of "Nulls" and

"Dead Spots" within the coverage area. Front and wall tampers GENERAL GUIDELINES The SiXREPEATER module uses a 5VDC power supply to charge the battery (Max wire length is 9.8 ft. (3m)). If the voltage drops to 3.6VDC a low battery occurs. NOTE:

It is incapable of charging the battery if the voltage is lower than 2.6VDC (it must be replaced.) Before mounting permanently, conduct the Go/No Go test

(see controllers instructions) to verify adequate signal strength, relocate if necessary. PLACEMENT Find the Null or Dead Spot 1. Enter the Go-No-Go test mode: For Lyric control:

Security > Tools > Installer Code > Test > Go-No-Go Test. 2. Activate any enrolled SiX transmitter in your hand. Listen for the panel to beep and acknowledge the fault. Can be installed in a residential environment and is designed to operate 200 feet through three walls of wood, aluminum and dry wall construction. Designed for a single repeat, meaning the correct path is transmitter > repeater > receiver. NOT transmitter >

repeater > repeater > receiver. 3. With the enrolled transmitter in your hand continue to fault/restore it as you walk further from the controller until the panel stops acknowledging it. This is the ideal mounting location. 4. Mount the SiXREPEATER in this location following the guidelines below. MOUNTING NOTE: for best results mount the SiXREPEATER as high as possible, keeping it away from metal objects. 1. Select a mounting position for the module. IMPORTANT!

DO NOT mount on or inside a metal enclosure/object. 2. Attach to the wall using the supplied screws. 3. Install the center screw to secure the back tamper to the wall. 4. Ensure the wiring is complete. Use cable ties as necessary to secure wiring. 5. Plug the power supply into an un-switched outlet and secure with screw. 6. Attach the backup battery wires. 1 MOUNTING DIAGRAM PLACEHOLDER, NEED NEW PLASTICS DESING BEFORE I CAN MOVE FORWARD WITH THIS ILLUSTRATION. Signal Strength Rang of 1-4 bars (green), should be a minimum 1 green bar for the zone being programmed. Four Red Bars indicate poor signal strength; the device should be relocated. See the controllers instruction for bar indication signal strength values. View via Lyric Program Zones or SiX Programming display, or AlarmNet 360. Icon Description 4 Green Bars 3 Green Bars 2 Green Bars 1 Green Bar 4 Red Bars Signal Strength Good Relocate ENROLLING For Lyric Controller 1. Set the Controller in Programming Mode and select SiX Programming. For Lyric: Security > Tools >Installer Code > Program >

SiX Programming 2. On the SiXREPEATER, power up:

Power LED flashes for approximately 20 seconds Power LED turns on Power LED turns on for 3-seconds SiXREPEATER sends the information to the control and the MAC ID displays 3. Press Save to complete the enrollment. FOR LYRIC GATEWAY Use AlarmNet 360 to enroll and program this sensor. FOR OTHER CONTROLS For other controls that support SiX series devices, see the controllers installation app for detail. NOTES:

Once enrolled in a system, the SiXREPEATER cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. Enrollment time varies depending on the signal strength between the device and the controller. When done, Power LED is ON for 3 seconds and the control beeps to confirm enrollment. 24-HOUR ENROLLMENT DELETION AND DEFAULT If the device is enrolled in a controller different than the intended controller, and you are unable to delete it from the unintended controller, default the device to factory default setting:

1. Open the cover and verify device is powered on. 2. Press and hold the tamper switch for 20 seconds. 3. The Green enrollment LED rapidly flashes and the SiXREPEATER defaults. This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery installed). TAMPER/LOW BATTERY REPORTING The SiXREPEATER reports this condition to the control. If a low battery or tamper condition exists, the enrolled zone used for the SiXREPEATER shows a trouble on the control. IMPORTANT!

The first battery test occurs one hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within one minute. SENSOR LOCATION FEATURE To verify the location of each SiX device in an installation, enter programming mode and select a SiX device zone. The device LED (located on the PCB) lights (can take up to 30 seconds). NOTE: This LED is not seen with the cover on. To view, the tamper switch must be pressed down on the SiXREPEATER. Select it again to turn the LED off or select the next device to locate. 2 SUPERVISION If module supervision is desired, assign the SiXREPEATERs enrolled zone to a supervisory zone type. This sends check-

in, low battery, AC loss, and RF jam messages. See Enrolling section. Program the zone configuration as follows:

Zone Type 8 (24-hour aux) Input Type 3 (supervised RF) Loop 1 LED STATUS TABLE NOTES:

The SiXREPEATER reports AC loss and RF jam conditions as low battery status, which is also displayed on the controls keypads. This prevents either condition from causing an alarm when the control is armed. The SiXREPEATER does not repeat a message that has already been repeated. If an actual low battery condition is reported, it takes up to 12 hours after AC power is restored for the low battery restore message to be sent (requires 12 hours for fully recharged battery). Green Yellow Red RSSI Reliable Signal Marginal Signal, relocated No Signal Power AC Powered Operating on Battery Low Battery REPLACING THE BATTERY RF Jamming OK, No Jamming Jam Detected Cant avoid Jamming 3 SPECIFICATIONS Voltage Transformer Part Number.................. 300-10259 Input Voltage ...................................... 100 ~ 240VAC, 50 ~60 Hz Operating Voltage .............................. 5VDC (1A) Maximum Transformer Distance ....... 9.8ft. (3m) Battery/ Pile ........................................ P/N 300-10342 Environmental Operating Temp ................................. 14 F (-10C) to 140F (60C) NOTE: Charging the lithium battery stops when temperature is below 32F (0C) Relative Humidity ............................... 95%, Non-condensing /

95%max. sans condensation Physical Dimensions ............................ Length 6.9 in Conduit Insert ........................ 1/2 in (12.7mm) Acceptable Cable Size .......... 14 22AWG

(175 mm) x Width 4.4 in (113 mm) x Depth 1.2 in (31 mm) REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. POUR LES LIMITES DU SYSTME DALARME AU COMPLET, REPORTEZ-VOUS AU GUIDE DINSTALLATION DU PANNEAU DE COMMANDE. RF EXPOSURE Warning The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures. APPROVAL LISTINGS / APPROBATIONS HOMOLOGATIONS FCC / IC - ETL Listed to UL268 & 521 cETL Listed to ULC S530 & S531 RF EXPOSURE Mise en Garde Exposition aux Frquences Radio: La/les antenne(s) utilise(s) pour cet metteur doit/doivent tre installe(s) une distance de sparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas tre situe(s) ni fonctionner paralllement tout autre transmetteur ou antenne, except en conformit avec les procdures de produit multi transmetteur FCC et ISED. OTHER STANDARDS RoHS FEDERAL COMMUNICATIONS COMMISSION (FCC) & ISED The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC / ISED STATEMENT This device complies with Part 15 of the FCC Rules, and ISEDs license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. Responsible Party / Issuer of Suppliers Declaration of Conformity: Honeywell International, 2 Corporate Center Drive., Melville, NY 11747, Ph: 516-577-2000 Partie responsable / metteur de la dclaration de conformit du fournisseur :

Honeywell International, 2 Corporate Center Drive., Melville, NY 11747, Tl. 516 577-2000 SUPPORT, WARRANTY, & PATENT INFORMATION For online support information, please go to / Pour de lassistance en ligne, visitez:

https://mywebtech.honeywellhome.com/

For the latest warranty information, go to / Pour les dernires informations de garantie, s'il vous plat aller : www.honeywell.com/security/hsc/resources/wa For patent information, see / Pour des informations sur les brevets, voir www.honeywell.com/patents MyWebTech Warranty Patents 2018 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved. / Honeywell est une marque dpose de Honeywell International Inc. Toutes les autres marques de commerce appartiennent leurs propritaires respectifs. Tous droits rservs. 800-24399 800-24399 8/18 Rev A

SiXREPEATER Wireless Repeater / Wireless Repeater Quick Installation Guide The Honeywell SiXREPEATER is an RF receiver and a transmitter and is intended to extend the range of Honeywells SiX series devices by 200 feet (nominal). The SiXREPEATER receives alarm, status, and control messages from SiX series devices, and forwards these messages to control panel. The control then responds accordingly (arm/disarm the system, initiate an alarm, etc. FEATURES Transmits its own status, including tamper, AC loss, and RF Jam. Status sent when change occurs or during the one hour supervisory check in. Provides a 24-hour backup rechargeable battery. Features a Spatial Diversity system that virtually eliminates the possibility of

"Nulls" and "Dead Spots" within the coverage area. Front and wall tampers GENERAL GUIDELINES Guide d'installation rapide The Honeywell SiXREPEATER is an RF receiver and a transmitter and is intended to extend the range of Honeywells SiX series devices by 200 feet (nominal). The SiXREPEATER receives alarm, status, and control messages from SiX series devices, and forwards these messages to control panel. The control then responds accordingly (arm/disarm the system, initiate an alarm, etc. 0FEATURES Transmits its own status, including tamper, AC loss, and RF Jam. Status sent when change occurs or during the one hour supervisory check in. Provides a 24-hour backup rechargeable battery. Features a Spatial Diversity system that virtually eliminates the possibility of "Nulls" and

"Dead Spots" within the coverage area. Front and wall tampers GENERAL GUIDELINES The SiXREPEATER module uses a 5VDC power supply to charge the battery

(Max wire length is 9.8 ft. (3m)). The SiXREPEATER module uses a 5VDC power supply to charge the battery (Max wire length is 9.8 ft. (3m)). If the voltage drops to 3.6VDC a low battery will occur. If the voltage drops to 3.6VDC a low battery will occur. NOTE: Anything lower than 2.6VDC, it is incapable of charging the battery; it must be replaced NOTE: Anything lower than 2.6VDC, it is incapable of charging the battery; it must be replaced Before mounting permanently, conduct the Go/No Go test (see controllers instructions) to verify adequate signal strength, relocate if necessary. Before mounting permanently, conduct the Go/No Go test (see controllers instructions) to verify adequate signal strength, relocate if necessary. The SIXREPEATER can be installed in a residential environment and is designed to operate 200 plus feet through 3 walls of wood, aluminum and dry wall construction. The SiXREPEATER is designed for a single repeat, meaning the correct path is transmitter > repeater > receiver. NOT transmitter > repeater > repeater >

receiver. The SIXREPEATER can be installed in a residential environment and is designed to operate 200 plus feet through 3 walls of wood, aluminum and dry wall construction. The SiXREPEATER is designed for a single repeat, meaning the correct path is transmitter > repeater > receiver. NOT transmitter > repeater > repeater > receiver. PLACEMENT Find the Null or Dead Spot 1. Enter the Go-No-Go test mode: For Lyric control: Security > Tools > Installer Code > Test > Go-No-Go Test. 2. Activate any enrolled SiX transmitter in your hand. Listen for the panel to beep and acknowledge the fault. 3. With the enrolled transmitter in your hand continue to fault/restore it until the panel stops acknowledging it. PLACEMENT Find the Null or Dead Spot 1. Enter the Go-No-Go test mode: For Lyric control: Security > Tools > Installer Code >

Test > Go-No-Go Test. 2. Activate any enrolled SiX transmitter in your hand. Listen for the panel to beep and acknowledge the fault. 3. With the enrolled transmitter in your hand continue to fault/restore it until the panel stops acknowledging it. 4. Mount the SiXREPEATER in this location following the guidelines below. 4. Mount the SiXREPEATER in this location following the guidelines below. MOUNTING NOTE: for best results mount the SiXREPEATER as high as possible, keeping it away from metal objects. 1. Select a mounting position for the module. In most installations, the best mounting location is close to the existing control panel. NOTES:

If needed, you may cut and splice (observing good workmanship) the battery wires and extend their length up to 3 ft. (0.9 meters) using 22 AWG wire, minimum. DO NOT mount on or inside a metal enclosure/object. 2. Attach to the wall using the supplied screws. 3. Install the center screw to secure the back tamper to the wall. 4. Ensure the wiring is complete. Use cable ties as necessary to secure wiring. 5. Plug the power supply into an un-switched outlet and secure with screw. 6. Attach the backup battery wires. ENROLLING Lyric Control Lyric Controller Enrollment Process, See Controllers installation instructions for its proper programming process. For Lyric Gateway Use AlarmNet 360 to enroll and program this sensor. For Other Controls For other controls that support SiX series devices, see the controllers installation app for details. NOTE: Once enrolled in a system, the SiXREPEATER cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. MOUNTING NOTE: for best results mount the SiXREPEATER as high as possible, keeping it away from metal objects. 1. Select a mounting position for the module. In most installations, the best mounting location is close to the existing control panel. NOTES:

If needed, you may cut and splice (observing good workmanship) the battery wires and extend their length up to 3 ft. (0.9 meters) using 22 AWG wire, minimum. DO NOT mount on or inside a metal enclosure/object. 2. Attach to the wall using the supplied screws. 3. Install the center screw to secure the back tamper to the wall. 4. Ensure the wiring is complete. Use cable ties as necessary to secure wiring. 5. Plug the power supply into an un-switched outlet and secure with screw. 6. Attach the backup battery wires. ENROLLING Lyric Control Lyric Controller Enrollment Process, See Controllers installation instructions for its proper programming process. For Lyric Gateway Use AlarmNet 360 to enroll and program this sensor. For Other Controls For other controls that support SiX series devices, see the controllers installation app for details NOTE: Once enrolled in a system, the SiXREPEATER cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. SIGNAL STRENGTH Range of 1-4 bars (green); should be minimum 1 green bar for the Zone being programmed. Four red bars indicate poor signal strength; the device should be relocated. See the Controllers instructions for bar indication signal strength values. View via Lyric Program Zones or SiX Programming display, or AlarmNet 360. SIGNAL STRENGTH Range of 1-4 bars (green); should be minimum 1 green bar for the Zone being programmed. Four red bars indicate poor signal strength; the device should be relocated. See the Controllers instructions for bar indication signal strength values. View via Lyric Program Zones or SiX Programming display, or AlarmNet 360. 24-HOUR ENROLLMENT DELETION AND DEFAULT If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended panel, reset default the device to factory default setting:

1. Open the cover and verify device is powered on. 2. Press and hold the tamper switch for 20 seconds. 3. The Green enrollment LED rapidly flashes and the SiXREPEATER defaults. This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery installed). 24-HOUR ENROLLMENT DELETION AND DEFAULT If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended panel, reset default the device to factory default setting:

1. Open the cover and verify device is powered on. 2. Press and hold the tamper switch for 20 seconds 3. The Green enrollment LED rapidly flashes and the SiXREPEATER defaults. This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery installed). SENSOR LOCATION FEATURE To verify the location of each SiX device in an installation, enter programming mode and select a SiX device zone. The device LED (located on the PCB) lights (can take up to 30 seconds). NOTE: This LED is not seen with the cover on. To view, the tamper switch must be pressed down on the SiXREPEATER. Select it again to turn the LED off or select the next device to locate. SUPERVISION If module supervision is desired, assign the SiXREPEATER to a zone. This sends check-

in, low battery, AC loss, and RF jam messages. When prompted, toggle the tamper switch to enroll the MAC ID number. The yellow LED should blink on when messages are sent. Program the zone configuration as follows:

SENSOR LOCATION FEATURE To verify the location of each SiX device in an installation, enter programming mode and select a SiX device zone. The device LED (located on the PCB) lights (can take up to 30 seconds). NOTE: This LED is not seen with the cover on. To view, the tamper switch must be pressed down on the SiXREPEATER. Select it again to turn the LED off or select the next device to locate. SUPERVISION If module supervision is desired, assign the SiXREPEATER to a zone. This sends check-in, low battery, AC loss, and RF jam messages. When prompted, toggle the tamper switch to enroll the MAC ID number. The yellow LED should blink on when messages are sent. Program the zone configuration as follows:

Zone Type 8 (24-hour aux) Input Type 3 (supervised RF) Loop 1 NOTES:

Zone Type 8 (24-hour aux) Input Type 3 (supervised RF) Loop 1 NOTES:

The SiXREPEATER reports AC loss and RF jam conditions as low battery status, which is also displayed on the controls keypads. This prevents either condition from causing an alarm when the control is armed. The SiXREPEATER reports AC loss and RF jam conditions as low battery status, which is also displayed on the controls keypads. This prevents either condition from causing an alarm when the control is armed. The SiXREPEATER will not repeat a message that has already been repeated. If an actual low battery condition is reported, it takes up to 12 hours after AC power is restored for the low battery restore message to be sent (requires 12 hours for fully recharged battery). The SiXREPEATER will not repeat a message that has already been repeated. If an actual low battery condition is reported, it takes up to 12 hours after AC power is restored for the low battery restore message to be sent

(requires 12 hours for fully recharged battery). TAMPER/LOW BATTERY REPORTING The SiXREPEATER reports this condition to the control. If a low battery or tamper condition exists all zones used on the module shows a trouble on the control. TAMPER/LOW BATTERY REPORTING The SiXREPEATER reports this condition to the control. If a low battery or tamper condition exists all zones used on the module shows a trouble on the control. IMPORTANT:

The first battery test occurs 1-hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within 1-minute. IMPORTANT:

The first battery test occurs 1-hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within 1-minute. LED INDICATIONS / LED INDICATIONS BATTERY / BATTERY RSSI Reliable Signal /

Reliable Signal Marginal Signal /

Marginal Signal No Signal /

No Signal Power AC Powered /

AC Powered Operating on Battery /

Operating on Battery Low Battery /

Low Battery RF Jamming OK, No Jamming /

OK, No Jamming Jam Detected /

Jam Detected Cant Avoid Jamming /

Cant Avoid Jamming Green /

Green Yellow /

Yellow Red /

Red Approval Listings / Approbations Homologations:

FCC / IC - ETL Listed to UL268 & 521 cETL Listed to ULC S530 & S531 Other Standards / Autres normes: RoHS FEDERAL COMMUNICATIONS COMMISSION (FCC) & ISED The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC / ISED STATEMENT This device complies with Part 15 of the FCC Rules, and ISEDs license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. Responsible Party / Issuer of Suppliers Declaration of Conformity: Honeywell International, 2 Corporate Center Drive., Melville, NY 11747, Ph: 516-577-2000 Partie responsable / metteur de la dclaration de conformit du fournisseur : Honeywell International, 2 Corporate Center Drive., Melville, NY 11747, Tl. 516 577-2000 BSPECIFICATIONS / SPCIFICATIONS:

Voltage / Voltage Transformer Part # / Transformer Part # ........................... 300-10259 Input Voltage / Input Voltage ............................................ 100 ~ 240VAC, 50 ~60 Hz Operating Voltage / Operating Voltage ............................. 5VDC (1A) Maximum Transformer Distance /

Maximum Transformer Distance ....................................... 9.8ft. (3m) Battery/ Pile ...................................................................... P/N 300-10342 Environmental /Environmental Operating Temperature /

Operating Temperature .................................................... 14 F (-10C) to 140F (60C) NOTE: Charging the lithium battery stops when temperature is below 32F (0C) NOTE: Charging the lithium battery stops when temperature is below 32F (0C) Relative Humidity / Relative Humidity ............................... 95%, Non-condensing / 95%

......................................................................................... max. sans condensation Physical / Physical Dimensions / Dimensions ................................................. Length / Length 6.9 in (175 mm) x Conduit Insert / Conduit Insert .......................................... 1/2 in (12.7mm) Acceptable Cable Size / Acceptable Cable Size ............... 14 22AWG See Honeywell Installation Guide P/N 800-

24399 https://mywebtech.honeywell.com/. Width / Width4.4 in (113 mm) x Depth / Depth 1.2 in (31 mm) 24399- https://mywebtech.honeywell.com/. Voir les instructions d'installation compltes 800-

800-24400Z 800-24400 5/18 Rev A CAUTION!

The batteries used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 212F (100C) or dispose of in fire. Use Panasonic CR123A or DURACELL DL123, DL 123A Lithium batteries. Use of other batteries may present a risk of fire or explosion. Keep used batteries away from children. Dispose of used batteries properly. Remove old batteries. Wait 10 seconds and then replace with four new batteries. To avoid a low battery indication when installing new batteries, both batteries must be installed within 15 seconds of installing the first one. Any low battery condition that may have occurred should clear when the back plate is installed. MISE EN GARDE!

Les piles utilises dans ce dispositif peuvent prsenter des risques d'incendie ou de brlure chimique si elles sont mal traites. Ne rechargez pas, ne dsassemblez pas, ne faites pas chauffer et ne jetez pas au feu les piles plus de 100 C (212 F). Utilisez des piles au lithium Panasonic CR123A ou DURACELL DL123, DL 123A. L'utilisation d'autres types de piles peut prsenter des risques de feu ou d'explosion. Gardez les vieilles piles hors de la porte des enfants. Dbarrassez-vous des batteries utilises de faon approprie. Retirez les vieilles piles. Attendez 10 secondes et remplacer-les par quatre nouvelles piles. Pour viter une indication de piles faibles lorsque vous installez de nouvelles piles, les dos (2) piles doivent tre installes en de de 15 secondes aprs l'installation de la premire. Toute condition de pilles faibles qui aurait pu se produire devrait tre rtablie une fois la plaque arrire installe. REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. POUR LES LIMITES DU SYSTME DALARME AU COMPLET, REPORTEZ-VOUS AU GUIDE DINSTALLATION DU PANNEAU DE COMMANDE Support / Pour de lassistance en ligne, visitez : https://mywebtech.honeywellhome.com/

U.S. warranty / U.S. garantie: www.honeywell.com/security/hsc/resources/wa For patent info, see: / Pour des informations sur les brevets, voir :

www.honeywell.com/patents MyWebTech Warranty Patents 2018 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved.

SiXREPEATERA Wireless Repeater SiXREPEATER Wireless Repeater INSTALLATION INSTRUCTIONS The Honeywell SiXREPEATER is an RF receiver/transmitter intended to extend the range of Honeywells SiX series devices by 200 feet (nominal range). The SiXREPEATER receives alarm, status, and control messages from SiX series devices. Once received, it forwards these messages to controller. The controller then responds accordingly (arm/disarm the system, initiate an alarm, etc.). FEATURES Transmits its own status, including tamper, AC loss, and RF Jam. Status sent when any change occurs or during the one hour supervisory check in. Provides a 24-hour backup rechargeable battery. Features a Spatial Diversity system that virtually eliminates the possibility of

"Nulls" and "Dead Spots" within the coverage area. Front and wall tampers GENERAL GUIDELINES The SiXREPEATER module uses a 5VDC power supply to charge the battery (Max wire length is 9.8 ft. (3m)). If the voltage drops to 3.6VDC a low battery occurs. NOTE:

It is incapable of charging the battery if the voltage is lower than 2.6VDC (it must be replaced.) Before mounting permanently, conduct the Go/No Go test

(see controllers instructions) to verify adequate signal strength, relocate if necessary. PLACEMENT Find the Null or Dead Spot Can be installed in a residential environment and is designed to operate 200 feet through three walls of wood, aluminum and dry wall construction. Designed for a single repeat, meaning the correct path is transmitter > repeater > receiver. NOT transmitter >

repeater > repeater > receiver. 1. Enter the Go-No-Go test mode: For Lyric control:

Security > Tools > Installer Code > Test > Go-No-Go Test. 2. Activate any enrolled SiX transmitter in your hand. Listen for the panel to beep and acknowledge the fault. 3. With the enrolled transmitter in your hand continue to fault/restore it as you walk further from the controller until the panel stops acknowledging it. This is the ideal mounting location for the SiXPTR. 4. Mount the SiXREPEATER in this location following the guidelines below. MOUNTING NOTE: for best results mount the SiXREPEATER as high as possible, keeping it away from metal objects. 1. Select a mounting position for the module. IMPORTANT!

DO NOT mount on or inside a metal enclosure/object. 2. Attach to the wall using the supplied screws. 3. Install the center screw to secure the back tamper to the wall. 4. Ensure the wiring is complete. Use cable ties as necessary to secure wiring. 5. Plug the power supply into an un-switched outlet and secure with screw. 6. Attach the backup battery wires. 1 MOUNTING DIAGRAM PLACEHOLDER, NEED NEW PLASTICS DESING BEFORE I CAN MOVE FORWARD WITH THIS ILLUSTRATION. ENROLLING 1. To enroll the device, use the programming app. When prompted for MAC ID, activate the device by powering up or, if already powered, press the tamper switch. 2. On the SiXREPEATER, power up:

Power LED flashes for approximately 20 seconds Power LED turns on Power LED turns on for 3-seconds SiXREPEATER sends the information to the control and the MAC ID displays NOTES:

Once enrolled in a system, the SiXREPEATER cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. Enrollment time varies depending on the signal strength between the device and the controller. When done, Power LED is ON for 3 seconds and the control beeps to confirm enrollment. 24-HOUR ENROLLMENT DELETION AND DEFAULT If the device is enrolled in a controller different than the intended controller, and you are unable to delete it from the unintended controller, default the device to factory default setting:

1. Open the cover and verify device is powered on. 2. Press and hold the tamper switch for 20 seconds. 3. The Green enrollment LED rapidly flashes and the SiXREPEATER defaults. This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery installed). TAMPER/LOW BATTERY REPORTING The SiXREPEATER reports this condition to the control. If a low battery or tamper condition exists, the enrolled zone used for the SiXREPEATER shows a trouble on the control. IMPORTANT!

The first battery test occurs one hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within one minute. SUPERVISION If module supervision is desired, assign the SiXREPEATERs enrolled zone to a supervisory zone type. This sends check-in, low battery, AC loss, and RF jam messages. See Enrolling section. Program the zone configuration as follows:

Zone Type 8 (24-hour aux) Input Type 3 (supervised RF) Loop 1 LED STATUS TABLE 2 NOTES:

The SiXREPEATER reports AC loss and RF jam conditions as low battery status, which is also displayed on the controls keypads. This prevents either condition from causing an alarm when the control is armed. The SiXREPEATER does not repeat a message that has already been repeated. If an actual low battery condition is reported, it takes up to 12 hours after AC power is restored for the low battery restore message to be sent (requires 12 hours for fully recharged battery). Green Yellow Red RSSI Reliable Signal Marginal Signal, relocated No Signal Power AC Powered Operating on Battery Low Battery REPLACING THE BATTERY RF Jamming OK, No Jamming Jam Detected Cant avoid Jamming SPECIFICATIONS Voltage Transformer Part Number .................. 300-10259 Input Voltage ...................................... 100 ~ 240VAC, 50 ~60 Hz Operating Voltage .............................. 5VDC (1A) Maximum Transformer Distance ........ 9.8ft. (3m) Battery/ Pile ........................................ P/N 300-10342 Environmental Operating Temp ................................. 14 F (-10C) to 140F (60C) NOTE: Charging the lithium battery stops when temperature is below 32F (0C) Relative Humidity ............................... 95%, Non-condensing /

95%max. sans condensation Physical Dimensions ............................ Length 6.9 in Conduit Insert ......................... 1/2 in (12.7mm) Acceptable Cable Size ........... 14 22AWG

(175 mm) x Width 4.4 in (113 mm) x Depth 1.2 in (31 mm) 3 REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. POUR LES LIMITES DU SYSTME DALARME AU COMPLET, REPORTEZ-VOUS AU GUIDE DINSTALLATION DU PANNEAU DE COMMANDE. RF EXPOSURE Warning The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures. APPROVAL LISTINGS / APPROBATIONS HOMOLOGATIONS FCC / IC - ETL Listed to UL268 & 521 cETL Listed to ULC S530 & S531 RF EXPOSURE Mise en Garde Exposition aux Frquences Radio: La/les antenne(s) utilise(s) pour cet metteur doit/doivent tre installe(s) une distance de sparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas tre situe(s) ni fonctionner paralllement tout autre transmetteur ou antenne, except en conformit avec les procdures de produit multi transmetteur FCC et ISED. OTHER STANDARDS RoHS FEDERAL COMMUNICATIONS COMMISSION (FCC) & ISED The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC / ISED STATEMENT This device complies with Part 15 of the FCC Rules, and ISEDs license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. Responsible Party / Issuer of Suppliers Declaration of Conformity: Honeywell International, 2 Corporate Center Drive., Melville, NY 11747, Ph: 516-577-2000 Partie responsable / metteur de la dclaration de conformit du fournisseur :

Honeywell International, 2 Corporate Center Drive., Melville, NY 11747, Tl. 516 577-2000 For Technical Support, call 1-877-748-7628, option 3 For documentation, call Customer Service at: 1-800-238-2727

(1-800-ADT-ASAP). www.honeywell.com/security/hsc/resources/wa U.S. warranty Patents www.honeywell.com/patents 800-24399-1&

800-24399-1 8/18 Rev A ADT Security Services 1501 Yamato Rd Boca Raton, FL 33431 4

SiXREPEATERA Wireless Repeater / Wireless Repeater/Wireless Repeater Quick Installation Guide The SiXREPEATER is an RF receiver and a transmitter and is intended to extend the range of Honeywells SiX series devices by 200 feet (nominal). The SiXREPEATER receives alarm, status, and control messages from SiX series devices, and forwards these messages to control panel. The control then responds accordingly (arm/disarm the system, initiate an alarm, etc. FEATURES Transmits its own status, including tamper, AC loss, Quick Installation Guide The SiXREPEATER is an RF receiver and a transmitter and is intended to extend the range of Honeywells SiX series devices by 200 feet (nominal). The SiXREPEATER receives alarm, status, and control messages from SiX series devices, and forwards these messages to control panel. The control then responds accordingly (arm/disarm the system, initiate an alarm, etc. FEATURES Transmits its own status, including tamper, AC loss, and Quick Installation Guide The SiXREPEATER is an RF receiver and a transmitter and is intended to extend the range of Honeywells SiX series devices by 200 feet (nominal). The SiXREPEATER receives alarm, status, and control messages from SiX series devices, and forwards these messages to control panel. The control then responds accordingly (arm/disarm the system, initiate an alarm, etc. FEATURES Transmits its own status, including tamper, AC loss, Status sent when change occurs or during the one Status sent when change occurs or during the one hour Status sent when change occurs or during the one and RF Jam. hour supervisory check in. RF Jam. supervisory check in. Provides a 24-hour backup rechargeable battery. Features a Spatial Diversity system that virtually eliminates the possibility of "Nulls" and "Dead Spots"

within the coverage area. Provides a 24-hour backup rechargeable battery. Features a Spatial Diversity system that virtually eliminates the possibility of "Nulls" and "Dead Spots"

within the coverage area. Front and wall tampers GENERAL GUIDELINES Front and wall tampers GENERAL GUIDELINES and RF Jam. hour supervisory check in. Provides a 24-hour backup rechargeable battery. Features a Spatial Diversity system that virtually eliminates the possibility of "Nulls" and "Dead Spots"

within the coverage area. Front and wall tampers GENERAL GUIDELINES The SiXREPEATER module uses a 5VDC power supply to charge the battery (Max wire length is 9.8 ft.

(3m)). If the voltage drops to 3.6VDC a low battery will occur. NOTE: Anything lower than 2.6VDC, it is incapable of charging the battery; it must be replaced Before mounting permanently, conduct the Go/No Go test (see controllers instructions) to verify adequate signal strength, relocate if necessary. The SIXREPEATER can be installed in a residential environment and is designed to operate 200 plus feet through 3 walls of wood, aluminum and dry wall construction. The SiXREPEATER is designed for a single repeat, meaning the correct path is transmitter > repeater >

receiver. NOT transmitter > repeater > repeater >

receiver. The SiXREPEATER module uses a 5VDC power supply to charge the battery (Max wire length is 9.8 ft. (3m)). If the voltage drops to 3.6VDC a low battery will occur. NOTE: Anything lower than 2.6VDC, it is incapable of charging the battery; it must be replaced Before mounting permanently, conduct the Go/No Go test (see controllers instructions) to verify adequate signal strength, relocate if necessary. The SIXREPEATER can be installed in a residential environment and is designed to operate 200 plus feet through 3 walls of wood, aluminum and dry wall construction. The SiXREPEATER is designed for a single repeat, meaning the correct path is transmitter > repeater >

receiver. NOT transmitter > repeater > repeater >

receiver. The SiXREPEATER module uses a 5VDC power supply to charge the battery (Max wire length is 9.8 ft.

(3m)). If the voltage drops to 3.6VDC a low battery will occur. NOTE: Anything lower than 2.6VDC, it is incapable of charging the battery; it must be replaced Before mounting permanently, conduct the Go/No Go test (see controllers instructions) to verify adequate signal strength, relocate if necessary. The SIXREPEATER can be installed in a residential environment and is designed to operate 200 plus feet through 3 walls of wood, aluminum and dry wall construction. The SiXREPEATER is designed for a single repeat, meaning the correct path is transmitter > repeater >

receiver. NOT transmitter > repeater > repeater >

receiver. PLACEMENT Find the Null or Dead Spot 1. Enter the Walk test mode. 2. Activate any enrolled SiX transmitter in your hand. Listen for the panel to beep and acknowledge the fault. PLACEMENT Find the Null or Dead Spot 1. Enter the Walk test mode. 2. Activate any enrolled SiX transmitter in your hand. Listen for the panel to beep and acknowledge the fault. PLACEMENT Find the Null or Dead Spot 1. Enter the Walk test mode. 2. Activate any enrolled SiX transmitter in your hand. Listen for the panel to beep and acknowledge the fault. 3. With the enrolled transmitter in your hand continue to fault/restore it until the panel stops acknowledging it. 3. With the enrolled transmitter in your hand continue to fault/restore it until the panel stops acknowledging it. 3. With the enrolled transmitter in your hand continue to fault/restore it until the panel stops acknowledging it. 4. Mount the SiXREPEATER in this location following the guidelines below. 4. Mount the SiXREPEATER in this location following the guidelines below. 4. Mount the SiXREPEATER in this location following the guidelines below. MOUNTING NOTE: for best results mount the SiXREPEATER as high as possible, keeping it away from metal objects. 1. Select a mounting position for the module. In most installations, the best mounting location is close to the existing control panel. NOTES:

If needed, you may cut and splice (observing good workmanship) the battery wires and extend their length up to 3 ft. (0.9 meters) using 22 AWG wire, minimum. DO NOT mount on or inside a metal enclosure/object. 2. Attach to the wall using the supplied screws. 3. Install the center screw to secure the back tamper to wall. the wall. 4. Ensure the wiring is complete. Use cable ties as necessary to secure wiring. 5. Plug the power supply into an un-switched outlet and secure with screw. 6. Attach the backup battery wires. ENROLLING To enroll the device, use the programming app. When prompted for MAC ID, activate the device by powering up or, if already powered, press the tamper switch. NOTE: Once enrolled in a system, the SiXREPEATER cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. MOUNTING NOTE: for best results mount the SiXREPEATER as high as possible, keeping it away from metal objects. 1. Select a mounting position for the module. In most installations, the best mounting location is close to the existing control panel. NOTES:

If needed, you may cut and splice (observing good workmanship) the battery wires and extend their length up to 3 ft. (0.9 meters) using 22 AWG wire, minimum. DO NOT mount on or inside a metal enclosure/object. 2. Attach to the wall using the supplied screws. 3. Install the center screw to secure the back tamper to the 4. Ensure the wiring is complete. Use cable ties as necessary to secure wiring. 5. Plug the power supply into an un-switched outlet and secure with screw. 6. Attach the backup battery wires. MOUNTING NOTE: for best results mount the SiXREPEATER as high as possible, keeping it away from metal objects. 1. Select a mounting position for the module. In most installations, the best mounting location is close to the existing control panel. NOTES:

If needed, you may cut and splice (observing good workmanship) the battery wires and extend their length up to 3 ft. (0.9 meters) using 22 AWG wire, minimum. DO NOT mount on or inside a metal enclosure/object. 2. Attach to the wall using the supplied screws. 3. Install the center screw to secure the back tamper to the wall. 4. Ensure the wiring is complete. Use cable ties as necessary to secure wiring. 5. Plug the power supply into an un-switched outlet and secure with screw. 6. Attach the backup battery wires. ENROLLING To enroll the device, use the programming app. When prompted for MAC ID, activate the device by powering up or, if already powered, press the tamper switch. NOTE: Once enrolled in a system, the SiXREPEATER cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. ENROLLING To enroll the device, use the programming app. When prompted for MAC ID, activate the device by powering up or, if already powered, press the tamper switch. NOTE: Once enrolled in a system, the SiXREPEATER cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. 24-HOUR ENROLLMENT DELETION AND DEFAULT If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended panel, reset default the device to factory default setting:

1. Open the cover and verify device is powered on. 2. Press and hold the tamper switch for 20 seconds. 3. The Green enrollment LED rapidly flashes and the SiXREPEATER defaults. This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery installed). SUPERVISION If module supervision is desired, assign the SiXREPEATER to a zone. This sends check-in, low battery, AC loss, and RF jam messages. When prompted, toggle the tamper switch to enroll the MAC ID number. The yellow LED should blink on when messages are sent. Program the zone configuration as follows:

24-HOUR ENROLLMENT DELETION AND DEFAULT If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended panel, reset default the device to factory default setting:

1. Open the cover and verify device is powered on. 2. Press and hold the tamper switch for 20 seconds. 3. The Green enrollment LED rapidly flashes and the SiXREPEATER defaults. 24-HOUR ENROLLMENT DELETION AND DEFAULT If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended panel, reset default the device to factory default setting:

1. Open the cover and verify device is powered on. 2. Press and hold the tamper switch for 20 seconds. 3. The Green enrollment LED rapidly flashes and the SiXREPEATER defaults. This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery installed). This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery installed). SUPERVISION If module supervision is desired, assign the SiXREPEATER to a zone. This sends check-in, low battery, AC loss, and RF jam messages. When prompted, toggle the tamper switch to enroll the MAC ID number. The yellow LED should blink on when messages are sent. Program the zone configuration as follows:

SUPERVISION If module supervision is desired, assign the SiXREPEATER to a zone. This sends check-in, low battery, AC loss, and RF jam messages. When prompted, toggle the tamper switch to enroll the MAC ID number. The yellow LED should blink on when messages are sent. Program the zone configuration as follows:

Zone Type 8 (24-hour aux) Input Type 3 (supervised RF) Loop 1 Zone Type 8 (24-hour aux) Input Type 3 (supervised RF) Loop 1 Zone Type 8 (24-hour aux) Input Type 3 (supervised RF) Loop 1 NOTES:

NOTES:

NOTES:

The SiXREPEATER reports AC loss and RF jam conditions as low battery status, which is also displayed on the controls keypads. This prevents either condition from causing an alarm when the control is armed. The SiXREPEATER will not repeat a message that has already been repeated. If an actual low battery condition is reported, it takes up to 12 hours after AC power is restored for the low battery restore message to be sent (requires 12 hours for fully recharged battery). The SiXREPEATER reports AC loss and RF jam conditions as low battery status, which is also displayed on the controls keypads. This prevents either condition from causing an alarm when the control is armed. The SiXREPEATER will not repeat a message that has already been repeated. If an actual low battery condition is reported, it takes up to 12 hours after AC power is restored for the low battery restore message to be sent (requires 12 hours for fully recharged battery). The SiXREPEATER reports AC loss and RF jam conditions as low battery status, which is also displayed on the controls keypads. This prevents either condition from causing an alarm when the control is armed. The SiXREPEATER will not repeat a message that has already been repeated. If an actual low battery condition is reported, it takes up to 12 hours after AC power is restored for the low battery restore message to be sent (requires 12 hours for fully recharged battery). TAMPER/LOW BATTERY REPORTING The SiXREPEATER reports this condition to the control. If a low battery or tamper condition exists all zones used on the module shows a trouble on the control. TAMPER/LOW BATTERY REPORTING The SiXREPEATER reports this condition to the control. If a low battery or tamper condition exists all zones used on the module shows a trouble on the control. TAMPER/LOW BATTERY REPORTING The SiXREPEATER reports this condition to the control. If a low battery or tamper condition exists all zones used on the module shows a trouble on the control. IMPORTANT:

The first battery test occurs 1-hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within 1-minute. IMPORTANT:

The first battery test occurs 1-hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within 1-minute. IMPORTANT:

The first battery test occurs 1-hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within 1-minute. LED INDICATIONS / LED INDICATIONS / LED INDICATIONS BATTERY / BATTERY / BATTERY Power RSSI Reliable Signal Reliable Signal Reliable Signal Marginal Signal /

Marginal Signal /

Marginal Signal No Signal /

No Signal /

No Signal AC Powered /

AC Powered /

AC Powered Operating on Battery /

Operating on Battery /

Operating on Battery Low Battery /

Low Battery /

Low Battery RF Jamming OK, No Jamming /

OK, No Jamming /

OK, No Jamming Jam Detected /

Jam Detected /

Jam Detected Cant avoid Jamming /

Cant avoid Jamming /

Cant avoid Jamming Green /

Green /

Green Yellow /

Yellow /

Yellow Red /

Red /

Red Approval Listings / Approbations Homologations / Approval Listings:

FCC / IC - ETL Listed to UL268 & 521 cETL Listed to ULC S530 & S531 Other Standards / Autres normes: RoHS FEDERAL COMMUNICATIONS COMMISSION (FCC) & ISED The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC / ISED STATEMENT This device complies with Part 15 of the FCC Rules, and ISEDs license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. Partie responsable / metteur de la dclaration de conformit du fournisseur : Honeywell International, 2 Corporate Center Drive., Melville, NY 11747, Tl. 516 577-2000 Responsible Party / Issuer of Suppliers Declaration of Conformity: Honeywell International, 2 Corporate Center Drive., Melville, NY 11747, Ph: 516-577-2000 SPECIFICATIONS / SPCIFICATIONS / SPECIFICATIONS:

Voltage / Voltage / Voltage Transformer / Transformer / Transformer ............ 300-10259 Input Voltage / Input Voltage / Input Voltage........ 100 ~ 240VAC, 50 ~60 Hz Operating Voltage / Operating Voltage /

Operating Voltage................................................ 5VDC (1A) Maximum Transformer Distance / Maximum Transformer Distance /

Maximum Transformer Distance .......................... 9.8ft. (3m) Battery/ Pile / Bateria ........................................... P/N 300-10342 Environmental / Environmental / Environmental Operating Temperature / Operating Temperature /

Operating Temperature ....................................... 14 F (-10C) to 140F (60C) NOTE: Charging the lithium battery stops when temperature is below 32F (0C) / Charging the lithium battery stops when temperature is below 32F (0C) / Charging the lithium battery stops when temperature is below 32F (0C) Relative Humidity /Relative Humidity /

Relative Humidity ................................................ 95%, Non-condensing / 95%

Physical / Physical / Physical Dimensions / Dimensions / Dimensions ............. Length / Length / Length 6.9 in (175 mm) x Conduit Insert / Conduit Insert Conduit Insert ..................................................... 1/2 in (12.7mm) Acceptable Cable Size / Acceptable Cable Size /

Acceptable Cable Size ....................................... 14 22AWG Width / Width / Width 4.4 in (113 mm) x Depth / Depth / Depth 1.2 in (31 mm) max. sans condensation CAUTION!

The batteries used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 212F (100C) or dispose of in fire. Use Panasonic CR123A or DURACELL DL123, DL 123A Lithium batteries. Use of other batteries may present a risk of fire or explosion. Keep used batteries away from children. Dispose of used batteries properly. Remove old batteries. Wait 10 seconds and then replace with four new batteries. To avoid a low battery indication when installing new batteries, both batteries must be installed within 15 seconds of installing the first one. Any low battery condition that may have occurred should clear when the back plate is installed. MISE EN GARDE!

Les piles utilises dans ce dispositif peuvent prsenter des risques d'incendie ou de brlure chimique si elles sont mal traites. Ne rechargez pas, ne dsassemblez pas, ne faites pas chauffer et ne jetez pas au feu les piles plus de 100 C (212 F). Utilisez des piles au lithium Panasonic CR123A ou DURACELL DL123, DL 123A. L'utilisation d'autres types de piles peut prsenter des risques de feu ou d'explosion. Gardez les vieilles piles hors de la porte des enfants. Dbarrassez-vous des batteries utilises de faon approprie. Retirez les vieilles piles. Attendez 10 secondes et remplacer-les par quatre nouvelles piles. Pour viter une indication de piles faibles lorsque vous installez de nouvelles piles, les dos (2) piles doivent tre installes en de de 15 secondes aprs l'installation de la premire. Toute condition de pilles faibles qui aurait pu se produire devrait tre rtablie une fois la plaque arrire installe. CAUTION!

The batteries used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 212F (100C) or dispose of in fire. Use Panasonic CR123A or DURACELL DL123, DL 123A Lithium batteries. Use of other batteries may present a risk of fire or explosion. Keep used batteries away from children. Dispose of used batteries properly. Remove old batteries. Wait 10 seconds and then replace with four new batteries. To avoid a low battery indication when installing new batteries, both batteries must be installed within 15 seconds of installing the first one. Any low battery condition that may have occurred should clear when the back plate is installed. REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. POUR LES LIMITES DU SYSTME DALARME AU COMPLET, REPORTEZ-VOUS AU GUIDE DINSTALLATION DU PANNEAU DE COMMANDE REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. DECLARACIN IFETEL La operacin de este equipo est sujeta a las siguientes dos condiciones 1. Es posible que este equipo o dispositivo no cause interferencia perjudicial y 2. Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. For Technical Support, call 1-877-748-7628, option 3 For documentation, call Customer 1-800-238-2727 (1-800-ADT-

Service at:

ASAP). Pour le support technique, appelez 1-877-748-7628, option 3. Pour la documentation, appelez le service clientle au 1-800-238-2727 (1-800-ADT-

ASAP). U.S. warranty / U.S. garantie www.honeywell.com/security/hsc/resources/wa Para Soporte Tcnico, llame al 1-877-748-7628, opcin 3 Para documentacin, llame a Servicio al Cliente a:

1-800-238-2727 (1-800-ADT-

ASAP). Patents / Brevets/Patentes www.honeywell.com/patents ADT Security Services Boca Raton, FL 33431 1501 Yamato Rd 800-24400-1b 800-24400-1 8/18 Rev A

CFS8DL6RPT / 573F-6RPT EXHIBIT 8 Label Information LABEL INFORMATION EXACT LOCATION OF THE LABEL:

Label is located on the right side of the inside plastic case cover in the location shown:

FCC/IC IDs Location Honeywell Internal Page 1 of 2 EXHIBIT 8 Label Information CFS8DL6RPT / 573F-6RPT LABEL Honeywell Internal Page 2 of 2

Ademco Inc 251 Little Falls Drive Wilmington, DE 19808 Request for Confidentiality Date: 07/26/18 Subject: Confidentiality Request for: CFS8DL6RPT Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 9.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Permanent Permanent*1 Short Term Permanent Short Term Short Term Short Term Short Term Short Term Permanent Permanent Permanent Permanent*3 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation

(Including both Functional Descriptions and Detailed Message Timing & Duty Factor Info) Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual Honeywell has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By:

(Signature/Title2)

/ Hardware Engineer Michael Antola

(Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

2 Corporate Center Drive Melville, NY 11747 516-577-2000 CFS8DL6RPT FCC COVER LETTER Date: 07/26/2018 To Whom It May Concern:

This letter is to inform you of our request for a new certification for our transceiver known as CFS8DL6RPT. The transceiver will operate under Part 15.247. Regards, X Michael Antola Honeywell Internal