FCC ID: HS9-S6ED3R THERMOSTAT

Smart Thermostat User Manual Getting to know the Smart Thermostat The indicators (mode button, Temperature down, Temperature up, Modes, Current temperature, Info icon, Energy saver) appear when a function is engaged. You will not see them all at once or when your device is inactive. You can also change the display settings later in the App. Whats in the box?

Device, cosmetic plate (optional), wire labeling stickers, Wall plate, Screws with anchors, installation tool. Things to know before you begin Before installing your device, you should be comfortable handling the electrical wiring in your home. If not, hire a professional to take care of the installation for you. This system is intended to replace an existing 24V thermostat and is compatible with most heating, cooling, and heat pump systems. It does not work with electric baseboard heat (120-240V) or millivolt systems. You must turn o power to your heating and cooling system at your circuit breaker or fuse box before installing your thermostat. The thermostat requires 2.4 GHz wi. Make sure you have your wi password handy before you begin the installation. You may want to heat or cool your home to a comfortable temperature before beginning the installation, since your system wont be operating during that time. WARNING: ELECTRICAL HAZARD Failure to follow these safety instructions could result in re, electric shock, or other injury or damage. Before installing your thermostat, turn o power to your heating and cooling system at your circuit breaker or fuse box. Verify that the power is o. Be aware that all electrical wires, regardless of function, can carry an electrical current. Treat all wires with equal caution. CAUTION: MERCURY NOTICE If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal. Troubleshooting tips If youve installed your thermostat and the display is blank:

The display will naturally dim when not in use. To restore full brightness, touch the center mode button. The touch-sensitive buttons may not work properly if you are wearing gloves. Conrm all wires have been connected properly. Check the circuit breaker, and any switches that control power to your heating and cooling system, and reset. Conrm that the heating/cooling power has been turned back on. Check that your furnace door is securely closed. Guided installation in the App Download the app. Weve created a guided installation experience within the app to take you step by step. To get started:

1. 2. 3. 4. Download the latest version of the app from the app store. Tap the More icon in the lower right of the app. Select Add a device and then follow the on-screen instructions to install the device. If prompted by the app to scan a barcode, scan the 2D barcode on the back of this guide. Get the most from your Smart Thermostat The app will help you get the best experience from your smart thermostat. You can use it to control the temperature remotely and set a schedule. Or let the app automatically manage the temperature with Routines and Hunches. Safety information FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE. Installation by a qualied professional may be required in your area. Refer to your local laws and building codes before performing electrical work; permits and/or professional installation may be required by law. Disconnect power to installation area at your circuit breaker or fuse box before beginning installation. Always use caution when handling electrical wiring. Failure to do so can cause electrical shock or equipment damage. Dont use this product to replace a high voltage system (such as a system with wire nuts or thick unlabeled wires) or any other incompatible system. Install your device in a location away from heat sources and direct sunlight to avoid temperature uctuations, which may aect temperature readings and device performance. Do not install your device near water or in humid conditions. The openings towards the back of the Smart Thermostat are used to sense temperature and humidity. If they become blocked, this will impair the devices functionality. If you repaint your home, make sure that your Smart Thermostat is removed before you paint to avoid paint blocking the holes. Your Smart Thermostat will remain cool to the touch during normal operation. If it ever feels hot to the touch, turn o the power to your heating and cooling equipment and contact technical support. Many homes built before 1978 contain lead-based paint. Check if your install area contains lead-based paint before beginning installation. Older homes may have wire fuses, rather than the switch ground fault interrupt fuses shown in the app. If you have such a home, and are not comfortable removing the fuse for your heating and cooling equipment, please consult a professional installer. If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal. Handle your device and its accessories with care. Your device or its accessories may have pointed edges which can lead to scratches, cuts, or other physical injury. Small Parts contained in your device and its accessories may present a choking hazard to small children. If the device appears damaged, discontinue use immediately. If the current wiring appears too short, wires have been lost in the wall, or you are not comfortable working with your wiring, contact a professional to take care of the installation for you. If no C wire is present, you will need to use a C wire power adapter. If you are not comfortable installing this adapter, contact a professional to take care of the installation for you. The Smart Thermostat requires 2.4 GHz wi to operate. If your home only has 5GHz wi, it is not compatible with this product. ENERGY STAR Compliance This Smart Thermostat is ENERGY STAR certied and meets the guidelines for energy eciency. Energy conservation preserves valuable resources. PRODUCT SPECIFICATIONS Electrical Rating: 24V ~, 60Hz, 0.2A, Temperature Rating: 32-104F (0-40C) FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired

(2) operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This Device is certified for fixed installations and must be installed to provide a separation distance of at least 20 cm from all persons. End users and installers must be provided with instructions to satisfy RF exposure compliance requirements. The device meets the FCC Radio Frequency Emission Guidelines. Information on the product is on file with the FCC and can be found by inputting such Product's FCC ID (which can be found on the device) into the FCC ID Search form available at https://www.fcc.gov/oet/ea/fccid. Additional safety, compliance, recycling, and other important information regarding your device can be found in the App in Help & Feedback > Legal & Compliance. RECYCLING YOUR DEVICE PROPERLY In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations

D C B A 4 3 2 1 RESIDEO PART NUMBER R32349078-001 R32349078-002 REV B B

(54.06) 3 4 5 R32349078-001

(52.03) 3 4 5 R32349078-002 1. PRINTING TO BE GRAY (PMS COOL GRAY 6C). (REF. MANUFACTURING NOTE: PRINT LABEL AT 600 DPI). 2. MUST BE A U.L. RECOGNIZED COMPONENT LABEL, PER U.L. MARKING AND LABELING SYSTEM PGJI2, FOR APPLICATION ON PC/ABS PLASTIC SURFACES, AT A TEMPERATURE RANGE OF -29C TO 49C. 3 PRINT 11 MM X 11 MM ECC-200 DATA MATRIX CODE, GRADE B OR HIGHER. BARCODE TO COMPLY WITH ABV:<<A>>; DSN:<<B>>; PID:<<C>>; PUK:<<D>>; PIN:<<E>>; BI:<<F>>

<<B>> DEVICE SERIAL NUMBER (DSN) UNIQUE IDENTIFIER GENERATED AT TIME OF MANUFACTURE. DSN IS 16 ALPHANUMERIC DIGITS LONG

<<C>> PRODUCT ID (g6Ny)

<<D>> COMPRESSED PUBLIC KEY PUBLIC KEY OF THE DEVICE THAT IS GENERATED DURING DEVICE MANUFACTURE. UNIQUE TO EVERY DEVICE. 80 CHARACTERS LONG AND FOLLOWS BASE64 ENCODING.

<<E>> SECRET PIN RANDOM SECRET PIN GENERATED AT TIME OF DEVICE MANUFACTURE. ALPHANUMERIC 9 CHARACTERS LONG, AND FOLLOWS BASE 64 ENCODING

<<F>> PWA SERIAL NUMBER UNIQUE PCBA SERIAL NUMBER GENERATED AT TIME OF MANUFACTURE. PWA SERIAL NUMBER IS 14 CHARACTERS IN LENGTH.

(REFERENCE: DETAILS ON BARCODE REQUIREMENTS ORIGINATED FROM THIS LINK:

4 PRINT 2.5MM X 28MM CODE 128 BARCODE, GRADE B OR HIGHER, ENCODING THE 16 DIGIT DEVICE SERIAL NUMBER (PER NOTE 5). ENCODE ONLY THE SERIAL NUMBER; NO ADDITIONAL PRE OR POST SUPPORTING CHARACTERS. 5 PRINT HUMAN READABLE 16-DIGIT DEVICE SERIAL NUMBER, PRECEDED BY DSN:

(DSN: XXXX XXXX XXXX XXXX), GENERATED ONLINE. PRINT USING HELVETICA NEUE REGULAR, 4.5 POINT. 6. THIS PRODUCT MUST BE PRODUCED USING COMPLIANT MATERIALS AND PROCESSES PER ES 50040083. DOC. FORMAT 1-11 4 B A REV. 8-19-21 1008614 DATE E.O. REV. DATE E.O. DIMENSIONS & TOLERANCES PER ANSI Y14.5M-1994 & RESIDEO ENGINEERING STANDARDS 3 THIS DRAWING CONTAINS PROPRIETARY INFORMATION AND SHALL NOT BE USED OR REPRODUCED WITHOUT WRITTEN AUTHORIZATION FROM RESIDEO ENGINEERING. MAT'L. R32348418-001 MAT'L. SPEC.

( ) FUNCTIONAL DIMENSIONING:

ALL DIMENSIONED AND UNDIMENSIONED GEOMETRY AND TOLERANCING ON THIS DRAWING IS DEFINED AND CONTROLLED BY THE DATABASE FILE. KEY INFORMATION IS REPRESENTED BY THIS DRAWING CONTAINING FUNCTIONAL DIMENSIONS. CONTROLLED BY DATABASE FILE:

2 FIRST USED ON

(SEE TAB) DIMENSIONS ARE IN:

THIRD ANGLE PROJECTION DWN. DES. INCHES MILLIMETERS PJB 8-18-21 N. CARLSON NEXT ASS'Y TITLE PRELIMINARY DRAFT CALLOUTS INDICATES DECREASING DIMENSION INDICATES INCREASING DIMENSION REFERENCE LABEL, PRINTED, OS TOLERANCE UNLESS NOTED MACHINED S 5 FORMED MILLIMETERS INCHES

+ 2 S

- 1 INCLUDING OVER 0 6 30 100 300 TO 6 TO 30 TO 100 TO 300 TO 1000 0.1 0.2 0.3 0.5 0.8

.0 .02

.00 .01

.000 .010 PROJECT NO. RESIDEO CONFIDENTIAL AND PROPRIETARY SIZE C DRAWING NUMBER R32349078 REV. B SCALE 2:1 SHEET 1 OF 1 1 ILLUSTRATOR D C B A

August 24th , 2021 Attention: Application Examiner RE:

Request for Confidentiality Applicant: Ademco Inc. FCC ID: HS9- S6ED3R To Whom It May Concern:

Permanent Confidentiality Request is hereby submitted by Ademco Inc. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:

Schematics Detailed Block Diagrams Detailed Operational/Functional Description Short-term Confidentiality Request is hereby submitted by Ademco Inc. to withhold from public review for a period of 45 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept confidential for a period of 45 days from the date of Authorization:

User manual Test setup photos External photos Internal photos Rationale for request for confidentiality:

Ademco Inc.has invested considerable time and materials in research and development to produce the referenced product.

[Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.] [Short term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development.]

If you have questions or need further information, please contact the undersigned. Sincerely, Paul Eastling Sr. Supervisor, Regulatory and Test Engineering Ademco Inc.

August 16th, 2021 Federal Communications Commission 445 12th Street SW Washington, DC 20554 Subject:

Limited Agency Agreement Ademco Inc. FCC ID: HS9-S6ED3R To Whom It May Concern:

We, Ademco Inc., hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number HS9-S6ED3R under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is August 17th 2021. The Limited Agency Agreement expires on September 30th 2021, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Paul Eastling Sr. Supervisor Ademco Inc.