FCC ID: HDC-W349E0 WiFi6 11ax wireless module

 

W349E0WiFi IoE Module

Page 1 of 9

Product Specification

W349E0

Wireless Module

W349E0is a host-less IoE Smart Network module that enables wireless internet

connectivity for any device wishing to be monitored or managed remotely. The

W349E0is architected for high performance, feature-rich applications. This module is

based on BCM43684, a highly integrated and feature-rich IEEE 802.11ax 4x4 5 GHz. 4

antenna ports are available for flexible use of external antennas for the appliances in

consideration.

1. Product Features

IEEE 802.11ax 4 streams radio.





 Host interfaces: PCIE

 ROM API support.

Full security support: WPS, WPA, WPA2, WAPI, WEP, TKIP.

W349E0WiFi IoE Module

Page 2 of 9

2. General Specification

Product Specification

Model Name

1 W349E0

Solution(HDK version)

Broadcom 43684

Form factor

PCIE module

Moisture sensitivity level MSL:3 (follow IC specification)

WLAN Standard

IEEE 802.11 ax/ac/b/g/n/a

Host interface

PCIE

Antenna configuration

4 antennas

Dimensions

Minimum

Typical

Maximum

Length

Width

Height

Weight

44.7

34.7

45

35

13.5

10

45.3

35.3

Unit

mm

mm

mm

g

Antenna Connector

3 RF conncetor

Electrical Specification

2.412GHZ-2.484GHz , 5.925 GHz-7.125 GHz

Frequency range

1.5170MHz~5250MHz, 5755MHz~5835MHz

2.5170MHz~5835MHz, (support DFS)

Electrostatic discharge

Human Body Model

±2000V, all pins

Standard: ANSI/ESDA/JEDEC JS-001-2012

Charged Device Model

±500V, all pins

Standard: JESD22-C101

W349E0WiFi IoE Module

Page 3 of 9

Minimum

Typical

Maximum

Unit

Operating Condition

Operation voltage

DC

Operation temperature

C-temp

Operation temperature

(Full load)

Operation temperature

(Low rate≤ 10Mbps, IOT)

I-temp

I-temp

Humidity Non-Operating

3.15

4.5

0

-40

-40

10

3.3

5.0

3.45

5.5

50

75

85

90

V

V

°C

°C

°C

%

Product Specification

Model Name

W349E0-A1

Solution

BROADCOM BCM43684

Form Factor

PCIe

WLAN Standard

IEEE 802.11 a/n/ac/ax 4T4R

WLAN

Host interface

PCIe VID

PCIe DID

PCIe SVID

PCIe SSID

Region Domain

Dimensions

PCIe

N/A

N/A

N/A

N/A

N/A

Antenna configuration

3 pieces 3x3mm RF connecters

Minimum

Typical

Maximum

50.9

29.75

4.2

50.8

29.85

4.0

6.78

50.7

29.95

3.8

Operating Condition

Minimum

Typical

Maximum

Unit

Length

Width

Height

Weight

DC

Unit

mm

mm

mm

g

V

°C

Operation voltage

Operation temperature

2.97/4.5

3.3/5

3.63/5.5

0

40

W349E0WiFi IoE Module

Page 4 of 9

Storage temperature

Humidity Non-Operating

-20

10

Electrical Specification

Data rate

Minimum

Typical

Maximum

Output power

5GHz

802.11a Mode

54Mbps

802.11n Mode

HT40/HT20 (mcs7)

802.11ac Mode

VHT40/VHT20 (mcs9)

802.11ax Mode

HE40/HE20 (mcs11)

Receiver Sensitivity

802.11a Mode

54Mbps

802.11n Mode

802.11ac Mode

802.11ax Mode

HT40(mcs7)

HT20 (mcs7)

VHT40 (mcs9)

VHT20 (mcs9)

HE40 (mcs11)

HE20 (mcs11)

17.5

17.5

16.5

14.5

-74

-71

-74

-66

-69

-58

-60

70

80

19

19

18

16

°C

%

Unit

dBm

dBm

dBm

dBm

dBm

dBm

dBm

dBm

dBm

dBm

dBm

W349E0WiFi IoE Module

Page 5 of 9

FCC Statement

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any

other antenna or transmitter.

This device is restricted to indoor use.

FCC Radiation Exposure Statement:

between the radiator & your body.

ISED Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,

Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject

to the following two conditions:

1. This device may not cause interference.

W349E0WiFi IoE Module

Page 6 of 9

2. This device must accept any interference, including interference that may cause undesired

operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux

CNR d’Innovation, Sciences et Développement économique Canada applicables aux

appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the

potential for harmful interference to co-channel mobile satellite systems.

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour

une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux

systèmes de satellites mobiles utilisant les mêmes canaux.

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with minimum

distance 20cm between the radiator & your body.

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de

20cm de distance entre la source de rayonnement et votre corps.

The transmitter module may not be co-located with any other transmitter or antenna.

Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

CAN ICES-003 (B)/NMB-003(B)

This module is intended for OEM integrators under the following conditions:

1. This module is certified pursuant to Part 15 rule section (15.407) and RSS-247.

2. This module has been approved to operate with the antenna types listed below, with the

maximum permissible gain indicated.

Frequency Band

Antenna Type Gain(dBi)

5150-5250MHz

5250-5350MHz

5470-5725MHz

PCB

PCB

PCB

5.541

5.672

5.481

W349E0WiFi IoE Module

Page 7 of 9

5725-5850MHz

PCB

5.537

3. Label and compliance information

Label of the end product:

FCC:

The host product must be labeled in a visible area with the following " Contains FCC ID:

HDC-W349E0".

The end product shall bear the following 15.19 statement: This device complies with part 15 of

the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

If the labelling area is considered too small and therefore it is impractical (smaller than the

palm of the hand) to display the compliance statement, then the statement may be placed in

the user manual or product packaging.

ISED:

This transmitter module is authorized only for use in device where the antenna may be

installed such that 20 cm may be maintained between the antenna and users. The final end

product must be labeled in a visible area with the following: “Contains transmitter module IC:

2250A-W349E0”.

Contient le module d'émission IC: 2250A-W349E0

The Host Model Number (HMN) must be indicated at any location on the exterior of the end

product or product packaging or product literature which shall be available with the end

product or online.

4. Information on test modes and additional testing requirements

This module is restricted to integration into hosts for indoor use only.

This module has been approved under stand-alone configuration.

The separate approval is required for all other operating configurations, including portable

configurations with respect to Part 2.1093, RSS-102 and different antenna configurations

The information on how to configure test modes for host product evaluation for different

operational conditions for a stand-alone modular transmitter in a host, versus with multiple,

simultaneously transmitting modules or other transmitters in a host can be found at KDB

Publication 996369 D04.

5. Additional testing, Part 15 Subpart B disclaimer

Appropriate measurements (e.g. FCC 15 B and ISED compliance) and if applicable additional

equipment authorizations (e.g. SDoC) of the host product to be addressed by the

integrator/manufacturer.

This module is only FCC authorized for the specific rule part 15.407, RSS-247 listed on the

grant, and the host product manufacturer is responsible for compliance to any other FCC

rules that apply to the host product as being Part 15 Subpart B and ISED compliant.

W349E0WiFi IoE Module

Page 8 of 9

6. The user manual of the end product should include:

FCC:

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

The antenna(s) used for this transmitter must be installed to provide a separation distance of

at least 20 cm from all persons.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

This device is restricted to indoor use.

The antenna(s) used for this transmitter must not transmit simultaneously with any other

antenna or transmitter.

ISED:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,

Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject

to the following two conditions:

1. This device may not cause interference.

operation of the device.

2. This device must accept any interference, including interference that may cause undesired

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux

CNR d’Innovation, Sciences et Développement économique Canada applicables aux

appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the

potential for harmful interference to co-channel mobile satellite systems.

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour

une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux

systèmes de satellites mobiles utilisant les mêmes canaux.

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with minimum

distance 20cm between the radiator & your body.

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un

W349E0WiFi IoE Module

Page 9 of 9

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de

20cm de distance entre la source de rayonnement et votre corps

The transmitter module may not be co-located with any other transmitter or antenna.

Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

CAN ICES-003 (B)/NMB-003(B)



 

 

 

 

 

 

 

 

 

 

 

 

 

 

Confidentiality Request Letter Date: December 27, 2020 Federal Communications Commission Authorization and Evaluation Division Subject: Request for confidentiality FCC ID: HDC-W349E0 To whom it may concern:

Short-term Confidentiality Pursuant to Public Notice DA 04-1705, and in order to comply with the marketing regulations in 47 C.F.R. 2.803 and the importation rules in 47 C.F.R. 2.1204 while ensuring that business-sensitive information remains confidential until the actual marketing of newly authorized devices, we are request the Commission grant temporary confidential treatment and not release the following attachments for routine public disclosure until 180 days after the grant date. 1. Internal Photographs 2. External Photographs 3. Users manual 4. Test Set up photos Permanent Confidentiality from public disclosure indefinitely. 1. Block Diagram 2. Schematics Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document 3. Operational Description / Software Security For U-NII Devices It is our understanding that test measurement reports and correspondence during the certification review process cannot be granted confidential treatment, and such information will be available for public review once the grant of equipment authorization is issued. Sincerely, Applicant Address

: Adtran

: 901 Explorer Boulevard, Huntsville, Alabama 35806-2807, United States Signature

_________________________________ Name and Job Title.

: Doug Parker, Manager Global Product Compliance Engineering E-mail Tel.

: doug.parker@adtran.com

: (256)963-8000

 

 

Modular Approval Request Letter Date: December 27, 2020 Subject: Modular Approval Attestation FCC ID: HDC-W349E0 Dear Reviewer, We, Adtran, have the WiFi6 11ax wireless module approved under single modular approval authorization. The requirements regulated in 47 CFR 15.212 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The shielding of the radio portion can be demonstrated in exhibition External Photo. 2. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chip AT93C86AY6-10YH-1.8(ATMEL). 3. The requirement of power supply regulation: The part number of the power regulator is BCM43684C0. 4. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. 5. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 6. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the user manual of this module. Please also see the exhibition Label Sample. 7. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. 8. The requirement of RF exposure: Please refer exhibition RF Exposure for the compliance of MPE RF exposure rule. Please do not hesitate to contact me for any questions of this request letter. Thank you. 901 Explorer Boulevard, Huntsville, Alabama 35806-2807, United Applicant

: Adtran Address Signature States

_________________________________ Name and Job Title.

: Doug Parker, Manager Global Product Compliance Engineering E-mail Tel.

: doug.parker@adtran.com

: (256)963-8000

 

 

Power of Attorney Date: December 27, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 FCC ID: HDC-W349E0 Product Name: WiFi6 11ax wireless module To whom it may concern:

Subject: Product Certification Representative Authorization Letter We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization to the FCC Rules and Regulations. Address : No.52, Huaya 1st Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Sporton International Inc. Name

: Leo Huang Job Title : Manager e-mail

: Leohuang@sporton.com.tw We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. 901 Explorer Boulevard, Huntsville, Alabama 35806-2807, United Applicant

: Adtran Address Signature States

_________________________________ Name and Job Title.

: Doug Parker, Manager Global Product Compliance Engineering E-mail Tel.

: doug.parker@adtran.com

: (256)963-8000

 

 

 

 

 

 

Date: December 27, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Declaration of composite/rated equipment for FCC ID: HDC-W349E0 To Whom it may concern, We, the undersigned, would like to declare that the composite portion catagorized as Other Class B digital devices & peripherals has been authorized under the Supplier's Declaration of Conformity (SDoC) procedures. Applicant

: Adtran 901 Explorer Boulevard, Huntsville, Alabama 35806-2807, United Sincerely, Address Signature States

_________________________________ Name and Job Title.

: Doug Parker, Manager Global Product Compliance Engineering E-mail Tel.

: doug.parker@adtran.com

: (256)963-8000