FCC ID: 2AOGIZWA009 aerQ Temperature & Humidity Sensor

arQ Temperature &

Humidity Sensor ZWA009 Used in this guide. Artculos utilizados en este manual / Utilis dans ce guide / In dieser Gebrauchsanweisung verwendete Bezeichnungen /

Usato in questa guida / Gebruikt in deze handleiding / Anvnds i den hr handboken. Note: QR Code used for SmartStart inclusion. DSK Code can be found on packaging. Do not remove or damage them. Remarque: code QR utiliss pour l'inclusion SmartStart. Le code DSK peut tre trouv sur l'emballage. Ne les enlevez pas et ne les endommagez pas. Hinweis: Der QR-Code wird fr die SmartStart-Einbindung verwendet. Der DSK-Code ist auf der Verpackung zu finden. Entfernen oder beschdigen Sie diesen nicht. PIN: 123456 SN: 201808 Important safety information. Please read this and the online guide(s) at support.aeotec.com/ths carefully. Failure to follow the recommendations set forth by Aeotec Limited may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and / or reseller will not be held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources. arQ Temperature & Humidity Sensor is intended for indoor use in dry locations only. Do not use in locations with direct water contact. Contains small parts; keep away from children. your Z-WaveTM network. 1. Remove the battery insulation strip from your arQ Temperature & Humidity Sensor. 2. Add arQ Temperature & Humidity Sensor to your Z-Wave network;

a. If your Z-Wave gateway supports SmartStart:

scan the QR code on arQ Temperature &

Humidity Sensor using the gateways app. Your sensor will join your Z-Wave network automatically. b. If your gateway does not support SmartStart;

i. Set your Z-Wave gateway into its add device mode. Refer to the gateways manual if you are unsure of how to perform this step. ii. Press the sensors button 3 times within 1.5 seconds; it is located on the top middle section of this device. iii. When arQ Temperature & Humidity Sensor is joining your Z-Wave network, its LED will blink green and red. iv. If pairing is successful, your sensors LED will change to a green colour for 3 seconds Action Button Botn de accin /

Bouton d'action /

Aktionstaste / Pulsante di azione / Actieknop /

Action Button Double-sided Tape for Magnet Quick start. The following will step you through installing arQ Temperature & Humidity Sensor and connecting it to before turning off. If pairing failed, your sensors LED will flash red 3 times; repeat the step or contact us for further support if needed. 3. After connecting arQ Temperature & Humidity Sensor to your gateway, test it in your chosen installation location by pressing the action button. If its LED briefly blinks green, it has a good connection to your gateway. Place or affix it in place using the included adhesive. The arQ Temperature & Humidity Sensor is now a part of your Z-Wave home control system. You can configure it and its automations via your Z-Wave system; please refer to your softwares user guide for precise instructions. Get help & learn more. Should you encounter any problem with arQ Temperature & Humidity Sensor, visit support.aeotec.com/ths or contact our support team via aeotec.com/contact. You can also learn more about your sensors features, configuration options, and technical specifications at the link. Gateway compatibility. To see if your sensor is known to be compatible with your Z-Wave gateway, please refer to aeotec.com/z-wave-gateways. Declaration of Conformity. Aeotec Limited declares that ZWA009 is in compliance with the essential requirements and other relevant provisions of RED 2014/53/EU, RoHS 2011/65/EU, IEC62321:2008 and EN50581:2012. The full text of the declaration is available from support.aeotec.com/ths/doc FCC ID: 2AOGIZWA009 In Europe contact Aeotec Group GmbH; Groe Johannisstrae 7, 20457 Hamburg, Germany.

& Aeotec Limited. Version: 501000900001 - AA service@aeotec.com www.aeotec.com FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Aeotec Limited Agent Authorization Company: Aeotec Limited Address: OFFICE 4 10/F KWAN CHART TOWER NO. 6 TONNOCHY ROAD WANCHAI HK Product Name: arQ Temperature & Humidity Sensor Model Number(s): ZWA009-A Product Description: arQ Temperature & Humidity Sensor We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Date: 2020/07/07 Signature:

Name:

Scott Ding Title:

Project Manager Company: Aeotec Limited

Authorization Letter Aeotec Limited We,

(the approval holder) Company name Addresss Aeotec Limited OFFICE 4 10/F KWAN CHART TOWER NO. 6 TONNOCHY ROAD WANCHAI HK declare that the following representative (agent):

Name (person) Bovey Yang Company name Shenzhen STS Test Services Co., Ltd. Addresss 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Fuyong Street, Baoan District, Shenzhen, Guangdong,China City Shenzhen China Country to act on our behalf on all matters concerning the application and documents submitted to Micom Labs for product certification below Product Description arQ Temperature & Humidity Sensor Type or Model(s) ZWA009-A Tradename or Brand(s) Aeotec Attestation:

City:

Date:

Name:

(this must be a person) Function:

Signature:

(or official company stamp) China 2020/07/07 Scott Ding Manager

Aeotec Limited Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2020/07/07 Subject; Request for Confidentiality FCC ID: 2AOGIZWA009 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure External Photos Test Setup Photos Internal Photos User Manual In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Scott Ding Title: Project Manager