FCC ID: 2ADEFAT-CD1 Airtame Radio Module

Airtame Hub Safety Manual (AT-CD1) Revision J - 1/6/2022 Contents:

1. Safety precautions 2. Legal notices (compliance, warranty etc.) For more support, visit airtame.com/support Find the latest version of the user manual on the company website: airtame.com/setup 1. Safety precautions The Airtame Hub has been designed with high attention to the safety of the user. However, if used improperly, the Airtame Hub can potentially cause fire, electrical shock or personal injury. To avoid any accidents, please pay attention to these guidelines:

Do not use the Airtame Hub outdoors. Do not place the Airtame Hub in direct sunlight. Do not expose the Airtame Hub to water or extreme conditions (moisture, heat, cold, dust) as it could potentially damage it or cause it to malfunction. Stop the use of the Airtame Hub immediately if it

(i) functions in an abnormal manner, (ii) produces unusual sounds, or (iii) produces unusual odors. Do not attempt to disassemble or repair the Airtame Hub yourself. Doing so voids the limited warranty and could harm you, your TV/projector, and/or the Airtame Hub. The 3M Command Strips may leave marks or detach from the wall. The Airtame Hub generates heat during use resulting in a temperature increase on the surface as it conducts the heat away. Handle with caution as the surface may feel hot to the touch. If you wish to remove it, unplug the Airtame Hub from the power source and let it cool down before touching it. Do not mount the Airtame Hub on a hot surface, near a ventilation or hot air exhaust as this can increase its temperature drastically and cause it to malfunction or shut down. The Airtame Hub should only be wall-mounted with the accompanying Airtame Hub Mounting Plate. The Airtame Hub Mounting Plate should be mounted on the wall with accompanying wall screws and wall plugs or with matching specifications:

Wall Screws: 2 x pan head tapping screw, material: zinc, thread size: 4.2. thread length: 38mm, head size: 8.2mm x 3.05mm Wall Plugs: 2 x universal expansion wall plug, material: nylon, diameter: 6, length: 30mm The Airtame Hub has been designed for mounting at heights 2 m above the floor The recommended ambient operating temperature of the Airtame Hub is: 0 to 45 C

(32 to 113 F). The recommended Operating Humidity is 20-90%RH non-condensing. WARNING: Choking hazard. Some Airtame Hub accessories should be kept away from small children as they may present a choking hazard. WARNING: Strong magnetism. Avoid placing any media that contains magnets or is sensitive to magnetism, such as bank cards, audio/video, tapes, or magnetic memory devices, near the magnetic wall mount. Media containing information sensitive to magnets should be kept at least 5 cm (2 inches) away from the product. Similarly, magnet-sensitive devices, such as a mechanical watch or measuring device, can be damaged if they come too close to the magnets in the Airtame Hub. This product is intended to be used with a Listed Power Adapter or DC power source marked L.P.S (or Limited Power Source), rated 12Vdc, max 30 W, or a 42.5~57 Vdc, 30W Gigabit Passive PoE injector, IEEE 802.3at, Tma=45 degree C. 2. Legal notices Contains Airtame Radio Module Model: AT-CD1 Contains FCC ID: 2ADEFAT-CD1 Contains IC: 12460A-ATCD1 Legal entities Airtame Inc PENN 1, 3rd Floor, Ste 320 250 West 34th St New York, NY 10119 United States Airtame ApS Danneskiold-Sams es All 24, 1 1434 K benhavn K Denmark License agreement and general terms The use of any software related to Airtame Hub or any products by Airtame ApS / Airtame Inc are governed by the Terms of Service and End User License Agreement which can be found at airtame. com/terms When using the Airtame Hub or any products of Airtame ApS / Airtame Inc you acknowledge and accept those terms. Warranty information Please check warranty information at airtame.com/terms Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. United States Wireless Radio Use This device is restricted to indoor use when operating in the 5.15 to 5.25 GHz frequency band. To comply with US FCC regulation, the country selection function has been completely removed from all US models. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. FCC Radiation Exposure Statement To satisfy FCC and IC exposure requirements, a separation distance of at least 20 cm (8 inches) should be maintained between the antenna of this device and persons during device operation. Operations at closer than this distance are not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter. Industry Canada (IC) Notices English:

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the Equivalent Isotropically Radiated Power (EIRP) is not more than that necessary for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. French:

Conformment la rglementation dIndustrie Canada, le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal (ou infrieur) approuv pour lmetteur par Industrie. Canada Dans le but de rduire les risques de brouillage radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la Puissance Isotrope Rayonne quivalente (PIRE) ne dpasse pas lintensit ncessaire ltablissement dune communication satisfaisante. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

(1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. IC Radiation Exposure Statement Cet appareil est conforme aux limites dexposition aux rayonnements de la IC CNR-102 dfinies pour un environnement non contrl. Afin dviter la possibilit de dpasser les limites dexposition aux frquences radio de la IC CNR-102, la proximit hu-

maine lantenne ne doit pas tre infrieure 20cm (8 pouces) pendant le fonctionnement normal. Wireless Radio Use Cet appareil est restreint usage en interieur pour la bande de frquence 5.15-5.25 Ghz. European Union Compliance Airtame ApS declares that this equipment is in compliance with the essential requirements and other provisions of Directive 2014/53/EU. The full Declaration of Conformity can be found at airtame.com/compliance European Union Wireless Radio Use This device is restricted to indoor use when operating in the 5.15 to 5.35 GHz frequency band in the following countries: Belgium, Bulgaria, Czech Republic, Denmark, Germany, Estonia, Ireland, Greece, Spain, France, Croatia, Italy, Cyprus, Latvia, Lithuania, Luxembourg, Hungary, Malta, Netherlands, Austria, Poland, Portugal, Romania, Slovenia, Slovakia, Finland, Sweden, Norway, Iceland, Lichtenstein, Switzerland, North Ireland and Turkey. UK Compliance Airtame ApS declares that this equipment is in compliance with Radio Equipment Regulations 2017. The full Declaration of Conformity can be found at airtame.com/compliance United Kingdom Wireless Radio Use This device is restricted to indoor use when operating in the 5.15 to 5.35 GHz frequency in UK. RF Exposure Information Statement This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. This equipment should be installed and operated to ensure a minimum of 20 cm spacing to any person at all times. Waste management Waste management of Airtame follows the WEEE Directive 2012/19/EU and the RoHS recast Directive 2011/65/EU. More information can be found at airtame.com/compliance Airtame Hub is designed by Airtame ApS / Airtame Inc www.airtame.com FCC: Federal Communications Commision CE: Conformit Europenne RCM: Regulatory Compliance Mark WEEE: Waste Electrical and Electronic Equipment Directive Warning: Please refer to the user manual for further instructions. CAN ICS- 3 (B)/NMB-3(B)

The FCC ID will be located in both user manual and on the packaging. The module is small

(approximately 10 x 10 mm), so placing the FCC ID on it in a type size large enough to be legible without the aid of magnification is impracticable.

4 A

t a m r o f g n w a r D i This drawing and any information or descriptive material set out on it are the condential and copyright property of Airtame ApS. and MUST NOT BE DISCLOSED, COPIED, LOANED in whole or part or used for any purpose without the written permission of Airtame ApS. Description Device Label Production Method Graphic Overlay Company Condential Colors Legal Owner Grey RAL 7037, Black RAL 9005 Danneskiold-Samses All 24, 1 1434 Copenhagen K, Denmark Finish Glossy Part Number Drawing Number CG10098 Drawn by Michael Planck Approved by Tolerance 0.5mm Document Format Vector PDF Date 28-02-2022 Scale 1:1 Revision A

AIRTAME APS Danneskiold Samsoes Alle 24, 1sal TV, Copenhagen K, Denmark 1434 Tel: 004527148803 ; Fax: 004522999067 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 SUBJECT: Class II Permissive Change for FCC ID: 2ADEFAT-CD1 The intention of this application is to enable the modular FCC ID: 2ADEFAT-CD1, original granted on 01/26/2022 to be integrated in Airtame Hub, AT-CD1. The module installed into host platform mentioned above is electronically and mechanically identical to the original certified module. The Original FCC testing on module under FCC ID: 2ADEFAT-CD1 was performed with an antenna of higher gain, and the antenna was connected to the module in an open environment. Except for the change above, the design, hardware and implementation are exactly same with original. Sincerely yours, Attila Sukosd attila@airtame.com

AIRTAME APS Danneskiold Samsoes Alle 24, 1sal TV, Copenhagen K, Denmark 1434 Tel: 004527148803 ; Fax: 004522999067 Date: July 19, 2022 FCC Laboratory 7435 Oakland Mills Rd Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2ADEFAT-CD1 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following documents from public disclosure indefinitely. Tune-up Procedure Above mentioned documents which contain detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we are requesting the Commission to withhold the following documents for 180 days after the grant of equipment authorization is issued:

It is our understanding that all measurement test reports, FCC ID label format cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. External Photos Internal Photos Test Setup Photos User Manual Best Regards, _______________________ Attila Sukosd attila@airtame.com

AIRTAME APS Danneskiold Samsoes Alle 24, 1sal TV, Copenhagen K, Denmark 1434 Tel: 004527148803 ; Fax: 004522999067 FCC Agent Authorization Date: February 11, 2022 To whom it may concern, AIRTAME APS hereby authorize Sporton International Inc. to act on our behalf in all matters relating to applications for FCC equipment authorization, including the signing of all documents relating to these matters. Any and all acts carried out by Sporton International Inc. on our behalf shall have the same effect as acts of our own. We also hereby certify that neither the applicant nor any party to the application is subject to a denial of Federal benefits that includes FCC benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1988. 21 U.S.C. 862. This authorization is limited to the product of as following:

FCC ID: 2ADEFAT-CD1 This authorization is valid until further written notice from the AIRTAME APS Sincerely, ________________________ Attila Sukosd attila@airtame.com

AIRTAME APS Danneskiold Samsoes Alle 24, 1sal TV, Copenhagen K, Denmark 1434 Tel: 004527148803 ; Fax: 004522999067 Date: November 3, 2021 This Change of IdenKcaKon request applies for a new FCC ID as established in 47 CFR 2.933 for a currently approved device. This applicaKon by AIRTAME APS will establish a new FCC ID: 2ADEFAT-CD1 under AIRTAME APS grantee code for the purpose of markeKng. The original grant to Murata Manufacturing Co., Ltd. will remain in 3. The equipment is electrically idenKcal. Only the trade name, and FCC ID number are dierent. 4. The original test results conKnue to be representaKve of and applicable to the equipment bearing the changed FCC Laboratory 7435 Oakland Mills Rd Columbia MD 21046 To whom it may concern, eect. Per 2.933(b) 1. The original idenKcaKon is VPYLBEE5XV1XA. 2. The original grant date is 02/17/2021. idenKcaKon. 5. Exterior photographs are included in this applicaKon. The following les are electronically submi_ed as a_achments:

Cover Le_er External Photos FCC ID label format and locaKon Should there be any quesKon, please feel free to contact us. Sincerely yours, AFla Sukosd aFla@airtame.com

AIRTAME APS Danneskiold Samsoes Alle 24, 1sal TV, Copenhagen K, Denmark 1434 Tel: 004527148803 ; Fax: 004522999067 Date: November 3, 2021 To whom it may concern, Please be noNed that I, A*la Sukosd, have designated Sporton Interna7onal Inc. as the person being responsible for this project and to sign the form 731 and other documentaNon. Any and all acts carried out by Sporton Interna7onal Inc. on the maUers of relaNng to all processes required in the FCC approval and any communicaNon needed with the naNonal authority, shall have the same legal authority as acts on our own behalf. We further cerNfy that neither the applicant nor any party to this applicaNon, as dened in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benets, that include FCC benets, pursuant to secNon 5301 of the AnN-Drug Abuse Act of 1998, 21 U.S.C. 862. This authoriza7on is limited to the product of as following:

FCC ID: 2ADEFAT-CD1 If you have any acknowledgement and response, please send it to Sporton Interna7onal Inc. directly. Sincerely yours, ________________________ A^la Sukosd a^la@airtame.com

ID ec arat on Letter of Change in October 25, 2021 Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 We Murata Manufacturing Co., Ltd. agree to give the permission to file a Change in ID for the following FCC ID. Product Name: Communication Module Model No.: LBEE5XV1XA FCC ID: VPYLBEE5XV1XA Approval Date: February 17, 2021 Brand Name: Murata Manufacturing Co., Ltd. For anew FCC ID application as below Company Name: Airtame ApS Model No.: AT-CD1 FCC ID: 2ADEFAT-CD1 Brand Name: Airtame There is no change in the design, circuitry, or construction with the aforementioned communication module, and the documents on file with FCC from the original certification remain unchanged and continue to be valid. The new application has its own brand name and FCC ID number. We accept for FCC officials to use the documents on file from the existing certification in processing of applicant's FCC ID. Sincerely, a Cee lew an }

Murata Manufacturing Co., Ltd

INNOVATOR IN ELECTRONICS Special Power of Attorney To whom it may concern:

I, MOTOO HAYASHI of Murata Manufacturing Co., Ltd. hereby appoint Kenji Hayashikoshi of Murata Manufacturing Co., Ltd. to represent me to act on my behalf to do any and all of the following:

Sign the following documents on my behalf and apply to FCC for the products

- Letter of agency and anti-drug

- Confidentiality cover letters

- Any other application document that requires a signature by grantee. The rights, powers and authority in fact to exercise any and all of the rights and powers herein granted shall commence and be in full force and effective for one year from April 15, 2021 unless specifically extended or terminated by either party. a Date: al st [Marck /202/

Place: Japan MOTOO HAYASHI Murata Manufacturing Co., Ltd.