KDC450UserManual November,2011 COPYRIGHT, LICENSE, and WARNING PAGE Copyright 2011 by KoamTac, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from KoamTac, Inc. The material in this manual is subject to change without notices. KoamTac reserves the right to make changes to any product to improve reliability, function, or design. KoamTac doesnt assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. Follow all warnings and instructions marked on manual and units. Use only the power source specified in this manual or marked on the units. May be covered under one or more pending and/or US Patents, including US Pat. No. 7,769,917;
7,954,710. KDC is a registered trademark and property of KoamTac, Inc. KoamTac is a registered trademark and property of KoamTac, Inc. KTSync is a registered trademark and property of KoamTac, Inc. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO ANY TYPE OF MOISTURE. DO NOT LOOK DIRECTLY INTO LASER OR POINT THE LASER INTO ANOTHER PERSONS EYES. EXPOSURE TO THE BEAM MAY CAUSE EYE DAMAGE. CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the users authority to operate the equipment. WARNING:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION TO USER:
This equipment has been tested and found to comply with the limit of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user, is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient / Relocate the receiving antenna. 2. 3. Connect the equipment into an outlet on a circuit difference from Increase the separation between the equipment and receiver. that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. WARNING: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE USED BATTERIES ACCORDING TO THE INSTRUCTIONS. FCC ID : VH9KDC450 Modifications not expressly approved by the manufacturer could void the user's authority to operated the equipment under FCC rules. RFID Spec 1. Operation frequency : 13.56 MHz 2. Modulation method : ASK 1. INTRODUCTION Congratulations on purchasing KoamTacs revolutionary barcode scanner and data collector. Lightweight and compact, with a user-friendly design and superior functionality, KoamTacs KDC works in a variety of portable applications. Use it independently or as an accessory to your PC, PDA, or smartphone. To find out more about KoamTac, Inc. and our family of products, visit us at www.koamtac.com. FEATURES KDC100 KDC200 KDC250 KDC300 KDC450 USB CONNECTIONS RECHARGEABLE BATTERY SCAN ENGINE AUTOMATIC DATA UPLOAD STORES10,000+
BARCODES KTSYNC SOFTWARE SDK FOR DEVELOPERS SUPPORTS MICROSOFT WINDOWS XP, VISTA, 7 &
MOBILE 5.0+
ANDROID, BLACKBERRY, IOS BLUETOOTH GPS RFID 2 YES Laser YES YES YES YES YES NO NO 1 YES Laser YES YES YES YES YES YES YES NO NO NO NO 1 YES Laser YES YES YES YES YES YES YES YES NO 1 YES Imager YES YES YES YES YES YES YES NO NO 1 YES Laser YES No YES YES YES YES YES NO YES Table 1 - Features of KDC 1.1 KDC Package The standard KDC package contains:
1. One KDC Barcode Data Collector 2. One USB Cable 3. One Lanyard (KDC100/200/250/300) or One Hand Strap (KDC450) 4. KoamTac Installation CD with KTSync for Microsoft Windows XP, Vista, 7 and Mobile 5.0+
KDC Device Driver User Manual 5. One Protective KDC Rubber Case (KDC100/200/250/300) or One Smartphone Protective Rubber Case (KDC450) NOTE: Depending on your region or distributor, package contents may vary. KDC100/200/250/300 KDC400 Figure 1 KDC Package 1.2 KDC Characteristics Before you use your KDC, please become familiar with its physical characteristics. Refer to Figure 2 and Figure 3 below which indicate placement of scan and scroll buttons, OLED display, LEDs, and ports on your KDC. All KDC models are similar except for the KDC100 which includes an additional USB connector. KDC100 Barcode Reader and Data Collector Figure 2 - Characteristics of KDC100 KDC200 / KDC250 / KDC300 Barcode Reader and Data Collector KDC200 KDC250/300 KDC450 Figure 3 - Characteristics of KDC200 / KDC250 / KDC300/KDC450 2. INSTALLATION 2.1 KoamTac Installation Wizard Windows XP WARNING: DO NOT CONNECT KDC TO USB PORT PRIOR TO INSTALLATION Insert KoamTac Installation CD into your computers CD drive. 1. 2. Click Start icon then My Computer icon. A listing of devices on your computer will be displayed including the disk drive containing the KoamTac Installation CD. 3. Click on the KoamTac Installation CD icon then click on the Setup directory. Click on the PC_Setup.exe file which executes the KTSync Setup Wizard. NOTES If KTSync Setup Wizard locates an older version of KTSync on your computer, you will be prompted to remove the older program before installing the new version. Select Remove KTSync then click Finish. When removal is complete, click Close. Go to Step 2 to run KTSync Setup Wizard. If you have any problems, please refer to the Manual Installation section. KTSync Setup Wizard Below are the screen images you will see during the installation of KTSync. Click Next icon in KTSync Setup Wizard window Click Next icon in KTSync Confirm Installation window Within a few minutes, installation of KTSync will be complete. Click Close icon and wait for the Device Driver Installation Wizard to load. Device Driver Installation Wizard Below are the screen images you will see during the installation of the KDC Device Driver. Click Next icon in Device Driver Installation Wizard window Click Continue Anyway icon in Software Installation Logo testing window Click Finish icon in Device Driver Installation Wizard window Connect KDC to Computer Using the USB cable included with the KDC, follow the directions below. Connect the cables ultra mini USB connector to the KDC. Connect the cables Type A USB connector to your PC. Wait until your computer beeps and/or displays the message Found New Hardware. Found New Hardware Wizard Select No, not this time option in Found New Hardware Wizard and click Next if your PC pops up the following Found New Hardware Wizard. Select Install the software automatically (Recommended) option in Found New Hardware Wizard and click Next if your PC pops up the following Found New Hardware Wizard. Click Continue Anyway icon in Software Installation Logo testing window Click Finish icon in Found New Hardware Wizard window Verify COM Port Address User can verify installed COM Port in Device Manager Vista and Windows 7 WARNING: DO NOT CONNECT KDC TO USB PORT PRIOR TO INSTALLATION 1. Insert KoamTac Installation CD into your computers CD drive. 2. Click Start icon then My Computer icon. A listing of devices on your computer will be displayed including the disk drive containing the KoamTac Installation CD. 3. Click on the KoamTac Installation CD icon then click on the Setup directory. Click on the PC_Setup.exe file which executes the KTSync Setup Wizard. NOTES If KTSync Setup Wizard locates an older version of KTSync on your computer, you will be prompted to remove the older program before installing the new version. Select Remove KTSync then click Finish. When removal is complete, click Close. Go to Step 2 to run KTSync Setup Wizard. If you have any problems, please refer to the Manual Installation section. KTSync Setup Wizard Below are the screen images you will see during the installation of KTSync. Click Next icon in KTSync Setup Wizard window Click Next icon in KTSync Confirm Installation window Click Close icon in KTSync Installation Complete window and wait for Device Driver Installation Wizard Click Install this driver software anyway in Windows Security window Click Finish icon in Device Driver Installation Wizard window Connect KDC to Computer Using the USB cable included with the KDC, follow the directions below. Connect ultra mini USB connector to the KDC. Connect Type A USB connector to your PC. Wait until your computer beeps and/or displays the message Found New Hardware. Verify COM Port Address User can verify installed COM Port in Device Manager Windows Mobile 5.0+
WARNING: PLEASE CONNECT PDA TO PC PRIOR TO INSTALLATION 1. PC_Setup.exe creates Mobile_Setup.exe file under C:\Program Files\KoamTac\KTSync\Windows.Mobile directory 2. Execute Mobile_Setup.exe Select Windows Mobile version to install. Click Next icon. Click OK icon in Pending Application Install window Follow the instructions on PDA screen COM port Assignment User should assign a COM port for KDC before using pKTSync. User should pair KDC with PDA using PDA Bluetooth manager and assign a COM port for Bluetooth communication Please refer to the PDA manual for the details of COM port assignment method Android Download and install aKTSync from the Android Market. http://www.androidzoom.com/android_applications/productivity/ktsync_luxv.html Blackberry Download and install bKTSync from the Blackberry App World. http://appworld.blackberry.com/webstore/content/16861?lang=en iPad/iPhone/iPod touch Download and install iKTSync from the Apple App Store. http://itunes.apple.com/us/app/ktsync/id372916602?mt=8 2.2 Manual Installation NOTE: If you have the KDC100, it has two ports, Ultra Mini and standard Type A which swings out. See Figure 2 for more details. Windows XP, Vista, and 7 Insert the KoamTac Installation CD into your computers disk drive. 1. 2. Create a directory called KoamTac on your computer. 3. Copy XP.Vista.7 directory from KoamTac CD to KoamTac directory. The XP.Vista.7 directory contains KTSync programs for Microsoft Windows XP, Vista, Windows 7 and user manuals. 4. Connect KDC cable to ultra mini USB connector on the KDC. 5. Connect KDC cable to Type A USB connector on your computer. Wait until your computer beeps and/or displays the message New Hardware Found. You will be prompted to search for a device driver for KDC. 6. Browse then select KTReader.inf file from the KoamTac directory created in Step 2. Follow screen prompts to continue with the device driver installation. NOTE: KTReader.inf is the device driver for 32bit Microsoft Windows XP, Vista, and Windows 7. If you have a 64bit computer, use KTReader.inf file from XP.Vista.64bit folder in the KoamTac directory. Windows Mobile 5.0+
Please connect your Windows Mobile PDA to your computer before software installation. Create a directory and name it KoamTac on the PDA. Copy Mobile5.0_6.0 directory from KoamTac CD to PDA KoamTac directory. Mobile5.0_6.0 contains KTSync programs for Microsoft Windows Pocket PC 2003, Mobile 5.0, Mobile 6.0 Standard, and Mobile6.0 Professional. It also includes KDC User Manual. 3. OPERATING THE KDC 3.1 Getting Started Attach Hand Strap to KDC To prevent possible damage to the KDC, we strongly recommend wearing it around your hand by the included hand strap. Also, please dont swing KDC by the hand strap because contact with another object may cause it to malfunction or become damaged. To attach the hand strap:
1. Fit the thin end of hand strap through the pillar of the KDC. 2. Loop the thick end of strap through the thin loop 3. Pull the strap tight to secure Charge KDC Battery Prior to using the KDC, you must charge its battery. To charge the battery, follow these directions. 1. Connect the KDC cable to the ultra mini USB connector on the KDC. 2. Connect the KDC cable to Type A USB connector on your computer. 3. Your KDC battery will begin charging. Within a few minutes, two small LEDs on the front panel will illuminate orange. When the battery is fully charged, the LEDs will illuminate green. KDC100 2 Hours KDC200 2 Hours KDC250/300 4 Hours Table 2 Approximate Time to Charge KDC Battery Configure KDC The KDC is designed to meet the data collection requirements of many different industries in a variety of dynamic situations. To perform well in these diverse environments, the KDC is designed to be configured easily and quickly. But, to perform at its maximum level, the KDC must be configured properly. Until you are familiar with configuring the KDC, it is recommended that you DO NOT modify the KDC settings. The KDC can be configured in three different methods which are explained in Section 3.3 KDC Menus, Chapter 4 Synchronization, and Appendix C Special Barcodes. CONFIGURATION METHODS FOR THE KDC KDC Menu KTSync Software Special Barcodes Press UP and DOWN Scroll Buttons simultaneously to access the KDC menu. Figure 4 - Location of Scroll Buttons 3.2 Basics Reading Barcodes Reading a barcode is simple. Point the KDC at a barcode and press the scan button. Be sure to point the scan engine at the barcode, not at your face, and make sure to position the light beam on the barcode. If the barcode is scanned successfully, you will hear one beep and the LEDs will illuminate in green. If the scan was unsuccessful, you will hear two beeps and the LEDs will illuminate in red. If you have problems scanning a barcode, try the following suggestions while pointing the KDC at the barcode and depressing the scan button. Modify the angle of the KDC in relation to the barcode, making the angle bigger or smaller as needed. Modify the distance between the barcode and the KDC, moving closer or further away as needed. Check option settings defined in the KDC menu section and change options as needed. Check that the barcodes width does not exceed the light beams width and vice versa. Synchronizing Barcode Data to PC Use the KTSync program to synchronize barcode data from the KDC to your PC. Please refer to Chapter 4 for details. KDC410(i) KDC415(i) KDC420(i) KDC425(i) KDC430(i) 3.3 KDC Menus Top Menu Sub Menu EAN13 EAN8 UPCA UPCE CODE39 ITF14 CODE128 I2of5 CODABAR GS1-128 CODE93 CODE35 Set Barcodes
(410/415) Options Enabled/Disabled Enabled/Disabled Enabled/Disabled Enabled/Disabled Enabled/Disabled Enabled/Disabled Enabled/Disabled Enabled/Disabled Enabled/Disabled Enabled/Disabled Enabled/Disabled Enabled/Disabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled BooklandEAN Enabled/Disabled Disabled Disabled EAN13withAddon Enabled/Disabled Disabled Disabled EAN8withAddon UPCAwithAddon Enabled/Disabled Disabled Disabled Enabled/Disabled Disabled Disabled UPCEwithAddon Enabled/Disabled Disabled Disabled Set Barcodes
(420/425) 1D Symbology Codabar Code 11 Code 32 Code 39 Code 93 Code 128 EAN-8 EAN-13 GS1 Composit I2of5 Matrix 2of5 MSI Plessey PosiCode GS1 Omni GS1 Limited GS1 Expanded S2of5 Ind S2of5 IATA TCL39 Telepen Trioptic UPCA UPCE0 UPCE1 2D Symbology AztecCode N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Postal Codes OCR AztecRunes CodablockF Code16K Code49 DataMatrix MaxiCode MicroPDF PDF417 QRCode HanXin Code Postnet PlanetCode UK Post Canada Post Kix Post Australia Post Japan Post China Post Korea Post OCR Off OCR A OCR B OCR USC OCR MICR OCR SEMI N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enable Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Barcode Options
(410/415) CodaBar_NoStartStop Chars Enabled/Disabled Disabled Disabled UPCE_as_UPCA Enabled/Disabled Disabled Disabled EAN8_as_EAN13 Enabled/Disabled Disabled Disabled UPCE_as_EAN13 Enabled/Disabled Disabled Disabled ReturnCheckDigit Enabled/Disabled Disabled Disabled VerifyCheckDigit Enabled/Disabled Disabled Disabled UPCA_as_EAN13 Enabled/Disabled Disabled Disabled I2of5_VerifyCheckDigit Enabled/Disabled Disabled Disabled Code39_VerifyCheckD igit I2of5_ReturnCheckDig it Code39_ReturnCheck Digit UPCE_ReturnCheckDi git UPCA_ReturnCheckDi git EAN8_ReturnCheckDi git EAN13_ReturnCheck Digit Enabled/Disabled Disabled Disabled Enabled/Disabled Disabled Disabled Enabled/Disabled Disabled Disabled Enabled/Disabled Enabled Enabled Enabled/Disabled Enabled Enabled Enabled/Disabled Enabled Enabled Enabled/Disabled Enabled Enabled N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Barcode Options
(420/425) Codabar Tx StartStop(Enable/disable) Digit(DoNotVerify/VerfyDONotTX/Verify Check DoTx) Concatenate(Disable/Enable/Required) Code39 Tx StartStop(Enable/disable) N/A N/A N/A N/A N/A N/A N/A N/A Disabled Disabled DoNotVerify DoNotVerify Enabled Enabled Disabled Disabled N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A I2of5 Code11 Code128 Telepen UPCA Digit(DoNotVerify/VerfyDONotTX/Verify Check DoTx) Append(Enable/Disable) Full ASCII(Enable/Disable) Digit(DoNotVerify/VerfyDONotTX/Verify Check DoTx) Check Digit(2 digits/1 digit) Concatenate(Disable/Enable) Output(Original/AIM) VerifyChkDgt(Enabled/Disabled) NumberSys(Enabled/Disabled) 2DgtAddenda(Enabled/Disabled) 5DgtAddenda(Enabled/Disabled) Req. Addenda(Enabled/Disabled) Sep. Addenda(Enabled/Disabled) Coupon Code(Enabled/Disabled) UPCE Expand(Enabled/Disabled) Req. Addenda(Enabled/Disabled) Sep. Addenda(Enabled/Disabled) Check Digit(Enabled/Disabled) NumberSys(Enabled/Disabled) 2DgtAddenda(Enabled/Disabled) 5DgtAddenda(Enabled/Disabled) EAN-13 VerifyChkDgt(Enabled/Disabled) 2DgtAddenda(Enabled/Disabled) 5DgtAddenda(Enabled/Disabled) Req. Addenda(Enabled/Disabled) Sep. Addenda(Enabled/Disabled) ISBN Trans.(Enabled/Disabled) EAN-8 VerifyChkDgt(Enabled/Disabled) 2DgtAddenda(Enabled/Disabled) 5DgtAddenda(Enabled/Disabled) Req. Addenda(Enabled/Disabled) Sep. Addenda(Enabled/Disabled) MSI Tx CheckChar(Enabled/Disabled) PosiCode A and B/A&B LimitedA/A&B LimitedB GS1 UPCEAN Ver.(Enabled/Disabled) GS1 Emulation(No Emulate/GS1 128 Emul/GS1 Emulate) PostNet Tx CheckChar(Enabled/Disabled) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A DoNotVerify DoNotVerify Disabled Disabled Disabled Disabled DoNotVerify DoNotVerify 2 digits 2 digits Disabled Disabled AIM AIM Enabled Enabled Enabled Enabled Disabled Disabled Disabled Disabled Disabled Disabled Enabled Enabled Enabled Enabled Disabled Disabled Disabled Disabled Enabled Enabled Enabled Enabled Enabled Enabled Disabled Disabled Disabled Disabled Enabled Enabled Disabled Disabled Disabled Disabled Disabled Disabled Enabled Enabled Disabled Disabled Enabled Enabled Disabled Disabled Disabled Disabled Disabled Disabled Enabled Enabled Disabled Disabled A&B LimitedB A&B LimitedB Disabled Disabled No Emulate No Emulate Disabled Disabled N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A PlanetCode Tx CheckChar(Enabled/Disabled) N/A N/A Disabled Disabled Scan Angle Filter Time Out Narrow/Wide Normal/High Wide Normal Wide Normal N/A N/A N/A N/A
.5 seconds to 10 seconds 2 second(s) 2 second(s) 2 second(s) 2 second(s) Min. Barcode Length 2 to 36 characters 1 to 4 level Enabled/Disabled 4 chars 2 level N/A 4 chars 2 level 4 chars 4 chars N/A N/A N/A Disabled Disabled Enabled/Disabled Disabled Disabled Disabled Disabled Continuous, Short, Medium, Long, Extra Long Medium Medium Medium Medium Finger Trigger Enabled/Disabled Start Position No. of Char(s) Action Wedge Only N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Wedge & Store Always Default Default Default Default Store Only Save if Sent Save if Not Sent Barcode only Packet Data Delete Delete None/In Prefix/In Suffix Start Position No. of Char(s) Action Default Default Default Default Delete Delete None 1 0 chars Select Delete Delete None 1 0 chars Select Delete Delete None 1 0 chars Select Delete Delete None 1 0 chars Select Scan Options Security Level Image Capture Auto Trigger Reread Delay Partial Display Wedge / Store Data Format Data Editor/Prefix Data Editor/Suffix Data Editor/AIM ID Data Editor/Partial Data Data Process N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Default N/A N/A N/A N/A N/A N/A N/A N/A Handshake Enabled/Disabled Disabled Disabled Disabled Disabled Terminator None, CR, LF, CR+LF, Tab Right/Left/Down/Up Arrow CR+LF CR+LF CR+LF CR+LF CR+LF Chk Duplicate Enabled/Disabled Disabled Disabled Disabled Disabled Power Pairing Enabled/Disabled Pairing neighboring Bluetooth devices Auto Connect Auto Power On Auto Power On/Power Off Time Enabled/Disabled Enabled/Disabled Disable, 1sec to 10second(s) Auto Power Off Enabled/Disabled Bluetooth Auto Power Off/Beep Warning Auto Power Off/Power Off Time Enabled/Disabled 1 to 30 minutes PowerOff Msg Enabled/Disabled MAC Address 12 Characters Bluetooth MAC Address BT FW Version v1.2.xrt Bluetooth Firmware Version Discovering Discovering neighboring Bluetooth devices Connecting to View Connect to Bluetooth device Wakeup Nulls Enabled/Disabled N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A BT Config ConnectDevice SPP Default(410) Default(415) Default(420) Default(425) Default(430) HID iOS iPhone SPP2.0 HID normal Enabled/Disabled Enabled/Disabled Default(410i) Default(415i) Default(420i) Default(425i) Default(430i) Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disable, 1sec to 10second(s) Disabled Disabled Disabled Disabled Disabled Auto Connect Auto Power On Auto Power On/Power On Time Auto Power Off Enabled/Disabled Disabled Disabled Disabled Disabled Disabled Auto Power Off/Beep Warning Auto Power Off/Power Off Time Enabled/Disabled Disabled Disabled Disabled Disabled Disabled 1 to 30 minutes 5 minutes 5 minutes 5 minutes 5 minutes 5 minutes PowerOff Msg Enabled/Disabled Disabled Disabled Disabled Disabled Disabled MAC Address 12 Characters Bluetooth MAC Address BT FW Version v1.2.xrt Bluetooth Firmware Version N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Wakeup Nulls BT Toggle Enabled/Disabled Disabled Disabled Disabled Disabled Disabled Enabled Enabled Enabled Enabled Enabled HID AutoLock Disabled,1,2,3,4,5,10,15 minutes 1 minutes 1 minutes 1 minutes 1 minutes 1 minutes HID Keyboard US,German,French,Italian,Spanish US US US US US HID Delay/Initial Disabled, 1,2,3,5,10 secs Disabled Disabled Disabled Disabled Disabled HID Delay/Inter char Disabled,10, 20, 30, 50, 100msec Disabled Disabled Disabled Disabled Disabled HID Ctrl Char Disabled, Alt+Numpad, ^+Character Disabled Disabled Disabled Disabled Disabled Enabled/Disabled Enabled Enabled Enabled Enabled Enabled BT Service System Config Power Pairing Discovering Pairing neighboring Bluetooth devices Discovering neighboring Bluetooth devices Connecting to View Connect to Bluetooth device HID Sync Memory Size(3.0 only) 0.5/3.5, 1/3, 2/2, 3/1, 4/0 Memory Status No. of Stored Barcodes Free Memory Available Memory(Empties Data) Reset Memory Application Memory BT Registry(KDC100 Not use) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Auto Erase Enabled/Disabled Disable Disable Disable Disable Disable Sleep Timeout Disable, 1sec to 10minute(s) 5 second(s) 5 second(s) 5 second(s) 5 second(s) 5 second(s) Date / Time Battery Version Button Lock Beep Sound YYYY:MM:DD &
HH:MM:SS
% of Battery Charge Available Firmware Version & Serial No. N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Enabled/Disabled Disabled Disabled Disabled Disabled Disabled Enabled/Disabled Enabled Enabled Enabled Enabled Enabled Beep Volume Low/High Auto Exit Port Status Enabled/Disabled Enabled/Disabled Display Format Time & Battery / Type & Time / Type &
Battery / Memory Status / GPS Data(KDC250 only)/Barcode Only Low N/A N/A N/A Low N/A N/A N/A Low N/A N/A N/A Low N/A N/A N/A Low N/A N/A N/A Menu Barcode Scrolling Brightness Enabled/Disabled Enabled/Disabled 1 to 15 level(8 level) Factory Default Restores Default Settings N/A N/A N/A N/A N/A N/A Disabled Disabled N/A N/A N/A N/A MSR Data Only Default Default Default Default N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A CR+LF Yes Yes Yes Disabled Enabled N/A N/A N/A N/A N/A N/A CR+LF CR+LF Yes Yes Yes Yes Yes Yes Disabled Disabled Disabled Disabled Data Format Track Separator Use Track1 Use Track2 Use Track3 MSR Config Packet Data Beep on error reading Enabled/Disabled Encryption Enabled/Disabled Table 3 - KDC Menu Options