all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 2.08 MiB | January 13 2020 | |||
1 |
|
Internal Photos | Internal Photos | 1.36 MiB | January 13 2020 | |||
1 |
|
External Photos | External Photos | 1.48 MiB | January 13 2020 | |||
1 |
|
Label and Label Location | ID Label/Location Info | 543.76 KiB | January 13 2020 | |||
1 |
|
Authorization letter | Cover Letter(s) | 246.22 KiB | January 13 2020 | |||
1 | Block Diagram | Block Diagram | January 13 2020 | confidential | ||||
1 |
|
Confidential Authorization | Cover Letter(s) | 312.39 KiB | January 13 2020 | |||
1 | Operational Description | Operational Description | January 13 2020 | confidential | ||||
1 | Schematics | Schematics | January 13 2020 | confidential | ||||
1 |
|
Test Reports | Test Report | 889.35 KiB | January 13 2020 | |||
1 |
|
Test Setup Photos | Test Setup Photos | 2.46 MiB | January 13 2020 |
1 | User Manual | Users Manual | 2.08 MiB | January 13 2020 |
R26B Door Phone Admin Guide About this manual Thank you for choosing Akuvoxs R26B door phone. This manual is intended for end userswho need to properly configure the door phone. This manualis applicable to 26.31.4.xx version, and it provides all functions configurations of R26B. Please visit Akuvox forum or consult technical support for any new information or latest firmware. Note: Please refer to universal abbreviation form in the end of manual when meet any abbreviation letter. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Content 1. Product Overview...............................................................................................................................................................................................1 1.1. Product Description................................................................................................................................................................................... 1 1.2. Connector Introduction..............................................................................................................................................................................1 1.3. LED Status Information.............................................................................................................................................................................2 2. Daily Use...............................................................................................................................................................................................................3 2.1. Making a Call..............................................................................................................................................................................................3 2.2. Receiving a Call......................................................................................................................................................................................... 3 2.3. Unlock..........................................................................................................................................................................................................4 2.3.1. Unlock by RFID Cards.................................................................................................................................................................... 4 2.3.2. Unlock by DTMF Codes................................................................................................................................................................. 4 3. Basic Setting....................................................................................................................................................................................................... 5 3.1. Getting Started........................................................................................................................................................................................... 5 3.1.1. IP Announcement............................................................................................................................................................................ 5 3.1.2. Access the device website.............................................................................................................................................................5 3.2. Password Modification.............................................................................................................................................................................. 6 3.2.1. Modify the Web Password............................................................................................................................................................. 6 3.3. Phone Configuration..................................................................................................................................................................................6 3.3.1. Language.......................................................................................................................................................................................... 6 3.3.2. Time................................................................................................................................................................................................... 7 3.3.3. Network............................................................................................................................................................................................. 7 3.3.3.1. VLAN.............................................................................................................................................................................................. 9 3.3.3.2. TR069.......................................................................................................................................................................................... 10 3.3.4. Sound.............................................................................................................................................................................................. 11 3.3.5. DND.................................................................................................................................................................................................12 3.4. Intercom Call............................................................................................................................................................................................ 13 3.4.1. Direct IP Call.................................................................................................................................................................................. 13 3.4.2. SIP Call........................................................................................................................................................................................... 14 3.4.2.1. SIP Account.................................................................................................................................................................................14 3.4.2.2. SIP Server 1&2...........................................................................................................................................................................15 3.4.2.3. Outbound Proxy Server............................................................................................................................................................ 15 3.4.2.4. Transport Type............................................................................................................................................................................15 3.4.2.5. NAT...............................................................................................................................................................................................16 3.4.3. Auto Answer................................................................................................................................................................................... 16 3.4.4. Web Call......................................................................................................................................................................................... 17 3.4.5. Push To Hang Up.......................................................................................................................................................................... 17 3.5. Security......................................................................................................................................................................................................17 3.5.1. Live view......................................................................................................................................................................................... 17 3.5.2. RTSP............................................................................................................................................................................................... 18 3.5.3. ONVIF............................................................................................................................................................................................. 19 3.6. Access Control......................................................................................................................................................................................... 20 3.6.1. Relay............................................................................................................................................................................................... 20 3.6.2. Card Setting................................................................................................................................................................................... 21 3.6.3. Open Relay via HTTP...................................................................................................................................................................22 3.6.4. Unlock via Exit Button...................................................................................................................................................................23 3.7. Reboot....................................................................................................................................................................................................... 24 3.8. Reset..........................................................................................................................................................................................................24 4. Advance Feature..............................................................................................................................................................................................25 4.1. Phone Configuration............................................................................................................................................................................... 25 4.1.1. LED..................................................................................................................................................................................................25 4.1.2. IR LED.............................................................................................................................................................................................26 4.1.3. RF Card Code Display Related...................................................................................................................................................27 4.2. Intercom.................................................................................................................................................................................................... 27 4.2.1. Call Time Related.......................................................................................................................................................................... 27 4.2.2. Return Code When Refuse..........................................................................................................................................................28 4.2.3. SIP Call Related............................................................................................................................................................................ 28 4.2.4. Codec.............................................................................................................................................................................................. 29 4.2.5. DTMF...............................................................................................................................................................................................30 4.2.6. Session Timer................................................................................................................................................................................ 31 4.2.7. Encryption.......................................................................................................................................................................................31 4.2.8. NAT..................................................................................................................................................................................................31 4.2.9. User Agent......................................................................................................................................................................................32 4.3. Access Control......................................................................................................................................................................................... 33 4.3.1. Web Relay...................................................................................................................................................................................... 33 4.4. Security......................................................................................................................................................................................................34 4.4.1. Anti-alarm....................................................................................................................................................................................... 34 4.4.2. Motion..............................................................................................................................................................................................35 4.4.3. Action...............................................................................................................................................................................................35 4.4.3.1. Action Parameters..................................................................................................................................................................... 35 4.4.3.2. Push Button Action.................................................................................................................................................................... 37 4.4.3.3. Input Interface Triggered Action...............................................................................................................................................38 4.4.3.4. Motion Triggered Action............................................................................................................................................................ 38 4.4.3.5. Action URL.................................................................................................................................................................................. 38 4.5. Upgrade.....................................................................................................................................................................................................39 4.5.1. Web Upgrade.................................................................................................................................................................................39 4.5.2. Autop Upgrade...............................................................................................................................................................................40 4.5.3. Backup Config File........................................................................................................................................................................ 42 4.5.4. DHCP Option................................................................................................................................................................................. 42 4.6. Log............................................................................................................................................................................................................. 43 4.6.1. Call log............................................................................................................................................................................................ 43 4.6.2. Door Log......................................................................................................................................................................................... 43 4.6.3. System Log.....................................................................................................................................................................................43 4.6.4. PCAP...............................................................................................................................................................................................44 R26B Admin Guide 1. Product Overview 1.1. Product Description Akuvox R26B is a SIP-compliant, hands-free, five buttons door phone. It can be connected with Akuvox indoor monitors for remote unlock control and monitor. Users can operate the indoor phone to communicate with visitors via voice and video. Users can also use RFID cards to unlock the door Its applicable in villas, office and so on. 1.2. Connector Introduction Ethernet (POE): Ethernet (POE) connector, which can provide both power and network connection. 12V/GND: External power supply terminal if POE is not available. RS485 A/B: RS485 terminal. 1 Figure 1.1 Product Description Figure 1.2-1 R26Bs interface R26B Admin Guide DOOR A/B: Trigger signal input terminal. Relay A/B (NO/NC/COM): Relay control terminal. Note: The general door phone interface diagram is only for reference. 1.3. LED Status Information LED Status Blue Red Green Pink Always on Flashing Flashing Always on Flashing Flashing Description Normal status Calling Network is unavailable Talking on a call Receiving a call Upgrading 2 Figure 1.2-2 General interface R26B Admin Guide 2. Daily Use 2.1. Making a Call Press one of the call buttons to call out the predefined SIP account or IP address and if LED turns green, it means the call has been answered. 2.2. Receiving a Call User can use IP phone or indoor monitor to call R26B and R26Bwill answer it automatically by default. If user disable auto answer, pressing button to answer incoming call. 3 R26B Admin Guide 2.3. Unlock 2.3.1.Unlock by RFID Cards Place the predefined user cards in RFID card reader to unlock. Under normal conditions, R26B will announce The door is now opened. 13.56 MHz RF card is supported on R26B. 2.3.2.Unlock by DTMF Codes Users can press the predefined DTMF code from an answer unit to remotely unlock the door during the call. Users will also hear The door is now opened. 4 R26B Admin Guide 3. Basic Setting 3.1. Getting Started 3.1.1.IP Announcement While R26B starts up normally, hold the top of call button for several seconds after the Status LED turns blue, voice system will enter IP announcement mode. In announcement mode, the IP address will be announced periodically and IP 0.0.0.0 would be announced if no IP address is gained. Press call button again to quit the announcement mode. 3.1.2.Access the device website Open a web browser, and access the corresponding IP address. Enter the default user name and password to login. The default administrator User Name and Password are shown below:
5 Figure 3.1.2 Access the device website R26B Admin Guide User Name: admin Password: admin Note: The recommended browser is Google Chrome. 3.2. Password Modification 3.2.1.Modify the Web Password Go to Security - Basic to modify password for webpage. To modify password foradmin or user account. Figure 3.2.1 Modify the web password 3.3. Phone Configuration 3.3.1.Language Go to Phone-Time/Lang to select language for webpage. Figure 3.3.1Language 6 R26B Admin Guide 3.3.2.Time Go to Phone - Time/Langto configure it. Time Zone: To select local time zone for NTP server. Primary Server: To configure primary NTP server address. Secondary Server: To configure secondary NTP server address, it takes effect if primary NTP server is unreachable. Update Interval: To configure interval between two consecutive NTP requests. System Time: The current time of the phone. 3.3.3.Network DHCP Mode In website, go to Network - Basic. Figure 3.3.2 Time Figure 3.3.3.1 Static IP mode 7 R26B Admin Guide R26B uses DHCP mode by default which will get IP address, subnet mask, default gateway and DNS server address from DHCP server automatically. Static IP Mode In Website, go to Network - Basic. If select static IP, users should manually setup IP address, subnet mask, default gateway and DNS server address. The figure right shows static IP settings. Local RTP Go to Network - Advanced to configure. Local RTP:To display and configure local RTP settings. Starting RTP Port: Determine the minimum port that RTP stream can use. Max RTP Port: Determine the maximum port that RTP stream can use. 8 Figure 3.3.3-2 Local RTP R26B Admin Guide SNMP Go to Network - Advanced to configure. SNMP:To display and configure SNMP settings. Active: To enable or disable SNMP feature. Port: To configure SNMP servers port. Trusted IP: To configure allowed SNMP server address. It could be an IP address or any valid URL domain name. Note: SNMP is Internet-standard protocol for managing devices on IP networks. 3.3.3.1. VLAN Go to Network - Advanced to configure. VLAN:To display and configure VLAN settings. Active: To enable or disable VLAN feature for designated port. VID: To configure VLAN ID for designated port. Priority: To select VLAN priority for designated port. 9 Figure 3.3.3-3 SNMP Figure 3.3.3.1 VLAN R26B Admin Guide Note: Please consult administrator for specific VLAN settings in the networking environment. 3.3.3.2. TR069 Go to Network - Advanced to configure. TR069:To display and configure TR069 settings. Active: To enable or disable TR069 feature. Version: To select supported TR069 version (version 1.0 or 1.1). ACS/CPE: ACS is short for auto configuration servers as server side, and CPE is short for customer-premise equipment as client side devices. URL:To configure URL address for ACS or CPE. User Name: To configure username for ACS or CPE. Password: To configure password for ACS or CPE. Periodic Inform: To enable periodically inform. Periodic Interval: To configure interval for periodic inform. 10 Figure 3.3.3.2 TR069 R26B Admin Guide Note:TR-069 is a technical specification entitled CPE WAN Management Protocol
(CWMP).It defines an application layer protocol for remote management of end-user devices. 3.3.4.Sound Go to Phone-Voice to configure volume and upload tone file. Mic Volume: To configure microphone volume. Speaker Volume:To configure speaker volume. Open Door Warning: Disable it, and users will not hear the prompt voice when the door is opened. RingBack Upload: To upload the ring back tone by users themselves. Opendoor Tone Upload: To upload the opendoor tone by users themselves. 11 Figure 3.3.4 Sound Figure 3.3.5 DND R26B Admin Guide 3.3.5.DND Go to Phone - Call Featureto configure DND feature. DND:DND allows phones to ignore any incoming calls. Return Code when DND: Determine what response code should be sent back to server when there is an incoming call if DND is on. DND On Code: The code is used to turn on DND on servers side, if configured, door phones will send a SIP message to server to turn on DND on server side if users press DND when DND is off. DND Off Code: The code is used to turn off DND on servers side, if configured, door phones will send a SIP message to server to turn off DND on server side if users press DND when DND is on. 12 R26B Admin Guide 3.4. Intercom Call 3.4.1.Direct IP Call Without sip server, users can also use IP address to call each other, but this way is only suitable in the LAN. Go to Phone - Call Feature to enable the direct IP call for door phones first. Go to Intercom - Basic to configure the IP address of the destination(E.g.IP address 192.168.10.91).One button for each button.After, press the push button to make direct IP call. Note: The push button number can also enter the SIP account. Figure 3.4.1-1 Direct IP call Figure 3.4.1-2 Push button 13 R26B Admin Guide 3.4.2.SIP Call SIP calls which use SIP numbers to make or receive calls should be supported by SIP server. Users need to register accounts and fill SIP feature parameters before using it. Go to Account - Basic to configure SIP account and SIP server for door phones first. 3.4.2.1. SIP Account Status: To display register result. Display Label: To configure label displayed. Display Name: To configure name sent to the other call party for displaying. Register Name: To enter extension number which users want and the number is allocated by SIP server. User Name: To enter user name of the extension. Password: To enter password for the extension. 14 Figure 3.4.2.1 SIP Account R26B Admin Guide 3.4.2.2. SIP Server 1&2 Server IP 1: To enter SIP servers IP address or URL. Server IP 2: To display and configure secondary SIP server settings. This is for redundancy, if registering to primary SIP server fails, the phone will go to secondary SIP server for registering. Registration Period: The registration will expire after registration period, and the phone will re-register automatically within registration period. 3.4.2.3. Outbound Proxy Server An outbound proxy server is used to receive all initiating request messages and route them to the designated SIP server. 3.4.2.4. Transport Type To display and configure transport type for SIP message. UDP: UDP is an unreliable but very efficient transport layer protocol. TCP: Reliable but less-efficient transport layer protocol. 15 Figure 3.4.2.2 SIP server 1&2 Figure 3.4.2.3 Outbound proxy server Figure 3.4.2.4 Transport type R26B Admin Guide TLS: Secured and reliable transport layer protocol. DNS-SRV: DNS record for specifying the location of services. 3.4.2.5. NAT To display and configure NAT settings. STUN: Short for session traversal utilities for NAT, a solution to solve NAT issues. Note:By default, NAT is disabled. After configuring SIP call related parameters, users can refer to the direct IP call part to dial out a SIP call. 3.4.3.Auto Answer Figure 3.4.2.5 NAT Go to Account - Advanced to enable auto answer feature for SIP calls. Figure 3.4.3 Auto answer 16 R26B Admin Guide 3.4.4.Web Call Go to Intercom-Basic to dial out or answer incoming call from website. Figure 3.4.4 Web call 3.4.5.Push To Hang Up Go to Intercom - Basic to configure. To enable or disable pushing button to hang up. Figure 3.4.5 Push to hang up 3.5. Security 3.5.1.Live view Go to Intercom - Live Stream to check the real-time video from R26B. In addition, user also can check the real-time picture via URL:
http://IP_address:8080/picture.jpg. Figure 3.5.1 Live view 17 R26B Admin Guide 3.5.2.RTSP R26B supports RTSP stream, go to Intercom - RTSP to enable or disable RTSP server. The URL for RTSP stream is:
rtsp://IP_address/live/ch00_0. RTSP Stream: To enable RTSP video and select the video codec. R26B supports H.264 video codec by default. H.264 Video Parameters: H.264 is a video stream compression standard. Different it provides an approximately identical level of video stream quality but a half bit rate. This type of compression is sometimes called MPEG-4 part 10. To modify the resolution, framerate and bitrate of H.264. MPEG4 Video Parameters: MPEG4 is one of the network video image the maximum compression ratio 4000:1. It is an important and common video function with great communication application integration ability and from H.263, compression standard. supports It 18 Figure 3.5.2 RTSP R26B Admin Guide less core program space. To modify the resolution, framerate and bitrate of MPEG4. 3.5.3.ONVIF R26B supports ONVIF protocol, which means R26Bs camera can be searched by other devices, like NVR which supports ONVIF protocol as well. Go to Intercom - ONVIF to configure ONVIF mode, its username and password. Switching ONVIF mode to Undiscoverableand it means users must program ONVIFs URL manually. The ONVIFs URL is:
http://IP_address:8090/onvif/device_service. 19 Figure 3.5.3 ONVIF R26B Admin Guide 3.6. Access Control 3.6.1.Relay Go to Intercom - Relay to configure relay. There are three terminals of relay: NO, NC and COM. NO stands for normally open contact while NC stands for normally closed contact. Relay ID:R26B supports two relays, users can configure them respectively. Relay Type:Default state means NC and COM are normally closed, while invert state means NC and COM are normally opened. Relay Delay:To configure the duration of opened relay. Over the value, the relay would be closed again. DTMF Option: To select digit of DTMF code, R26B supports maximum 4 digits DTMF code. DTMF:To configure 1 digit DTMF code for remote unlock. 20 Figure 3.6.1 Relay R26B Admin Guide Multiple DTMF: To configure multiple digits DTMF code for remote unlock. Relay Status:Low means that COM is connecting to NC while High means that COM is connecting to NO. Note:Relay operate a switch and does not deliver power, so users should prepare power adapter for external devices which connects to relay. 3.6.2.Card Setting Go to Intercom - Card setting, to manage card access system. Import/Export Card Data the card data file, which is R26B supports import or export convenient for administrator to deal with a large number of cards. The maximum card data file is 200K which is around 500 cards. Note: Please consult administrator for the template RFID cards data file. Obtain and Add Card 21 Figure 3.6.2-1 Card setting Figure 3.6.2-2 Card setting R26B Admin Guide Switch card status to Card Issuing and click Apply;
Place card on the card reader area and click Obtain;
Name card, choose which door you want to open and the valid day and time;
Click Add to add it into list. Note: Users can use card to access only when card status has been switched to Normal. Door Card Management Valid card information will be shown in the list. Administrator could delete one cards access permission or empty all the list. 3.6.3.Open Relay via HTTP Users can use a URL to remote unlock the door. Go to Intercom - Relay to configure. Switch: Enable this function. Disable by default. UserName & Password: Users can setup the username and password for HTTP unlock. 22 Figure 3.6.2-3 Card setting Figure 3.6.3 Open relay via HTTP R26B Admin Guide URLformat:
http://IP_address/fcgi/do?action=OpenDoor&UserName=&Passwor d=&DoorNum=1 3.6.4.Unlock via Exit Button Go to Intercom - Input to configure input settings. R26B supports two input triggers Input A/B (DOOR A/B). Input Service:To enable or disable input trigger service. Trigger Option: To choose open circuit trigger or closed circuit trigger. Low means that connection between door terminal and GND is closed, while high means the connection is opened. Action to execute: To choose which action to execute after the input terminal is triggered. Http URL: To configure URL, If HTTP action is chosen. Open Relay: To configure relay to open. Door Status: To show the status of input signal. 23 Figure 3.6.4 Unlock via exit button R26B Admin Guide 3.7. Reboot Go to Upgrade - Basic, users can reboot the phone. Figure 3.7 Reboot 3.8. Reset Go to Upgrade - Basic, users can reset the phone to factory settings. Figure 3.8.Reset 24 R26B Admin Guide 4. Advance Feature 4.1. Phone Configuration 4.1.1.LED Go to Intercom - LED Setting to configure the LED status.To setup the LED lighting mode. State: There is five states: Normal, Offline, Calling, Talking and Receiving. Color Off: The default status is OFF. Color On: It can support three color: Red, Green, Blue. Blink Mode: To setup the different blink frequency. LED Control:
Use HTTP URL to remote control the LED status. Http format:
25 Figure 4.1.1-1 LED Figure 4.1.1-2 LED R26B Admin Guide http://PhoneIP/fcgi/do?action=LedAction&State=1&Color=1&Mode
=2500 Status: 1=Idle; 2=OffLine; 3=Calling; 4=Talking; 5=Receiving; Color:
1=Green; 2=Blue; 3=Red; Mode: 0=Always On; 1=Always Off;
500/1000/1500/2000/25000/3000 4.1.2.IR LED Go to Intercom - Advanced to configure. Photoresistor: The setting is for night vision, when the surrounding of R26B is very dark, infrared LED will turn on and R26B will turn to night mode. Photoresistor value relates to light intensity and larger value means that light intensity is smaller. Users can configure the Min and Max bound and when photoresistor value is larger than Max bound, turn on. As contrast, when photoresistor value is smaller than Min bound, infrared LED will turn off and device turns to normal mode. infrared LED will 26 Figure 4.1.2 IR LED R26B Admin Guide 4.1.3.RF Card Code Display Related Go to Intercom - Advanced to configure. RFID Display Mode:To be compatible different card number formats. The default 8HN means hexadecimal. 4.2. Intercom 4.2.1.Call Time Related Go to Intercom - Basic to configure. Max Call Time: To configure the max call time. Max Dial Time: To configure the max incoming dial time, available when auto answer is disabled. Dial Out Time: To configure the max no answer call time. Hang Up After Open Door: To set the time that hang up the call after open the door. Figure 4.1.3 RF card code display related Figure 4.2.1-1 Call time related Figure 4.2.1-2 Call time related Figure 4.2.1-3 Hang up after open door 27 R26B Admin Guide 4.2.2.Return Code When Refuse Go to Phone - Call Feature - Others to configure. Return Code When Refuse: Allows users to assign specific code as return code to SIP server when an incoming call is rejected. 4.2.3.SIP Call Related Go to Account-Advanced to configure the SIP call related. Max Local SIP Port: To configure maximum local SIP port for designated SIP account. Min Local SIP Port: To configure maximum local SIP port designated SIP account. Caller ID Header: To choose caller ID header format. Anonymous Call: If enabled, R26B will block its information when calling out. Anonymous Call Rejection: If enabled, calls who block their information will be screened out. for 28 Figure 4.2.2 Return code when refuse Figure 4.2.3 SIP call related R26B Admin Guide Missed Call Log: If enabled, any missed call will be recorded into call log. Prevent Hacking: If enabled, it will prevent SIP messages from hacking. 4.2.4.Codec Go to Account - Advanced to configure SIP call related codec. SIP Account: To choose which account to configure. Audio Codec:R26B support four audio codec: PCMA, PCMU, G729, G722. Different audio codec requires different bandwidth, users can enable/disable them according to different network environment. Note: Bandwidth consumption and sample rates are as below:
Codec PCMA PCMU Bandwidth Sample Rates 64kbit/s 64kbit/s 8kHz 8kHz 29 Figure 4.2.4-1 Codec R26B Admin Guide G729 G722 8kbit/s 64kbit/s 8kHz 16kHz Video Codec: R26B supports H.264 standard, which provides better video quality at substantially lower bit rates than previous standards. Codec Resolution: R26B supports four resolutions: QCIF, CIF, VGA, 4CIF and 720P. Codec Bitrate: To configure bit rates of video stream. Codec Payload: To configure RTP audio video profile. Go to Phone - Call Feature to configure multicast related codec. 4.2.5.DTMF Go to Account - Advanced to configure RTP audio video profile for DTMF and its payload type. Type: Support Inband, Info, RFC2833 or their combination. 30 Figure 4.2.4-2 Codec Figure 4.2.4-3 Codec Figure 4.2.5 DTMF R26B Admin Guide How To Notify DTMF: Only available when DTMF type is Info. DTMF Payload: To configure payload type for DTMF. 4.2.6.Session Timer Go to Account - Advanced to configure it. If enabled, the on going call will be disconnected automatically once the session expired unless its been refreshed by UAC or UAS. 4.2.7.Encryption Figure 4.2.6 Session timer Go to Account - Advanced to configure it.If enabled, voice will be encrypted. Figure 4.2.7 Encryption 4.2.8.NAT Go to Account - Advanced to display NAT related settings. UDP Keep Alive message: If enabled, R26B will send UDP keep-alive message periodically to router to keep NAT port alive. Figure 4.2.8 NAT 31 R26B Admin Guide UDP Alive Msg Interval: Keep alive message interval. Rport: Remote Port, if enabled, it will add remote port into outgoing SIP message for designated account. 4.2.9.User Agent Go to Account - Advanced to configure it. To customize user agent field in the SIP message. to specific value, users could see the If users agent information from network package. is not set by default, users could see the company name, model number and firmware version from network package. If user agent is set 32 Figure 4.2.9 User agent R26B Admin Guide 4.3. Access Control 4.3.1.Web Relay R26B can support extra web relay which is connected with the door phone via network. Go to Phone - WebRelay to configure. Type: Connect web relay and choose the type. IP Address: Enter web relays IP address. UserName: It is an authentication for connecting web relay. Password: It is an authentication for connecting web relay. Web Relay Action: Web relay action is used to trigger the web relay. The action URL is provided by web relay vendor. Web Relay Key: If the DTMF keys same as the local relay, the web relay will be open with local relay. But if there are different, the web relay is invalid. Figure 4.3.1-1 Web relay Figure 4.3.1-2 Web relay 33 R26B Admin Guide Web Relay Extension: The webrelay can only receive the DTMF signal from the corresponding extension number. Note: Users can modify username and password in web relay website. 4.4. Security 4.4.1.Anti-alarm Go to Intercom - Advanced to configure. R26B integrates internal gravity sensor for the own security, and after enabling tamper alarm, the gravity of R26B changes dramatically, the phone will alarm. Gravity sensor threshold stands for sensitivity of sensor. if Figure 4.4.1 Anti-alarm 34 R26B Admin Guide 4.4.2.Motion R26B supports motion detection, go to Intercom - Motion to configure detection parameter. Motion Detection: To enable or disable motion detection. Motion Delay:To configure minium time gap between two snapshots. Motion Detect Time Setting: To make motion detect time for a whole week. 4.4.3.Action R26B supports to send notifications, snapshots via email and ftp transfer method, or calls via SIP call method, when trigger specific actions. 4.4.3.1. Action Parameters Go to Intercom - Action to set action receiver. 35 Figure 4.4.2-1 Motion Figure 4.4.2-2 Motion R26B Admin Guide Email Notification Senders email address: To configure email address of sender. Receivers email address: To configure email address of receiver. SMTP server address: To configure SMTP server address of sender. SMTP user name: To configure user name of SMTP service
(usually it is same with senders email address). SMTP password: To configure password of SMTP service (usually it is same with the password of senders email). Email subject: To configure subject of email. Email content: To configure content of email. Email Test: To test whether email notification is available. FTP Notification FTP Server: To configure URL of FTP server. FTP User Name: To configure user name of FTP server. FTP Password: To configure password of FTP server. FTP Test: To test whether FTP notification is available. Figure 4.4.3.1-1 Action parameters Figure 4.4.3.1-2 Action parameters 36 R26B Admin Guide SIP Call Notification SIP Call Number: To configure SIP call number. SIP Call Name: To configure display name of R26B. Three specific actions which will be triggered in R26B:
4.4.3.2. Push Button Action Go to Intercom - Basic to configure. Enable this function, the device will record any changes of the surrounding environment then send the message or picture to the corresponding receiver. Action to execute: Tick the suit the suitable way to receive the action message. HTTP URL: If you tick HTTP URL, and then enter the HTTP server IP address in the HTTP URL area. When the device detects any changes, it will send HTTP network package. 37 Figure 4.4.3.2 PushButton action R26B Admin Guide Input Interface Triggered Action 4.4.3.3. Go to Intercom - Input to configure. Action to execute: To choose which action to execute after triggering. Http URL: To configure URL, If HTTP action is chosen. Action Delay: To configure after how long to execute to send out notifications and trigger relay. Open Relay: To configure which relay to trigger. 4.4.3.4. Motion Triggered Action Go to Intercom - Motion to configure. Action to execute: To choose which action to execute after triggering. Http URL: To configure URL, If HTTP action is chosen. SDMC Upload: Upload the capture to the SDMC. 4.4.3.5. Action URL Action URL can be triggered by some predefined incidents. 38 Figure 4.4.3.3 Input interface trigger action Figure 4.4.3.4 Motion trigger action R26B Admin Guide request Go to Phone - Action URL, pick Active to be Enabled, pick to demand triggered incident, each HTTP to have to including the key and value, use= to separateeach value staring with $. For example, input http://server IP address/help.xml?mac=$mac, when the relay of R26B is triggered successfully, the phone will send a HTTP packet to the server, through the HTTP package to know the MAC of the phone. Open Relay Success incident, Figure 4.4.3.5 Action URL 4.5. Upgrade 4.5.1.Web Upgrade Go to Upgrade - Basic, users can upgrade firmware. Reset to factory setting and reboot. Upgrade: Choose .rom firmware from the PC, and then click Submit to start update. Figure 4.5.1 Web update 39 R26B Admin Guide 4.5.2.Autop Upgrade this SIP message is sent Go to Upgrade - Advanced to configure automatically update servers settings. PNP Option Plug and Play, once PNP is enabled, the phone will send SIP subscription message to PNP server automatically to get auto provisioning servers address. By default, 224.0.1.75 (PNP server address by standard). Manual Autop Autop (Auto-Provisioning) is a centralized and unified upgrade of telephone. It is a simple and time-saving configuration for phone. It is mainly used by the device to download corresponding configuration document from the server using TFTP / FTP / HTTP /
HTTPS network protocol. To achieve the purpose of updating the device configuration, making the users to change the phone to multicast address 40 Figure 4.5.2-1 Autop update Figure 4.5.2-2 Autop update R26B Admin Guide configuration more easily. This is a typical C/S architecture upgrade mode, mainly by the terminal device or PBX server to initiate an upgrade request. URL: Auto provisioning server address. User Name: Configure if server needs an username to access, otherwise left blank. Password: Configure if server needs a password to access, otherwise left blank. Common AES Key: Used for phone to decipher common auto provisioning configuration file. AES Key (MAC): Used for phone to decipher MAC-oriented auto provisioning configuration file (for example, file name could be 0C1105888888.cfg if phones MAC address is 0C1105888888). Note: AES is one of many encryption, it should be configured only when configure file is ciphered with AES, otherwise left blank. Automatic Autop To display and configure auto provisioning mode settings. 41 Figure 4.5.2-3 Autop update R26B Admin Guide This auto provisioning mode is actually self-explanatory. For example, mode Power on means phone will go to do provisioning every time it powers on. Note: Please refer to the related feature guide from Akuvox forum. 4.5.3.Backup Config File Go to Upgrade - Advanced to backup the config file. Export Autop Template: To export current config file. Others: To export current config file (Encrypted) or import new config file. 4.5.4.DHCP Option To display and configure DHCP setting for AutoP. Option 66/43 is enable by default. It can support HTTPS, HTTP, FTP, TFTP server. Customer Option: Enter the server URL. Click Submit to save. 42 Figure 4.5.3-1 Backup config file Figure 4.5.3-2 Backup config file Figure 4.5.4 DHCP Option R26B Admin Guide Note: To make DHCP autop URL works, disable. the PNP should be 4.6. Log 4.6.1.Call log Go to Phone - Call Log, users can see a list of call log which have dialed, received or missed. Users can delete calls from list. 4.6.2.Door Log Go to Phone - Door Log, users can see a list of door log which records card information and data. 4.6.3.System Log Go to Upgrade - Advanced to configure system log level and export system log file. 43 Figure 4.6.1 Call log Figure 4.6.2 Door log R26B Admin Guide System log level: From level from 0 to 7.The higher level means the more specific system log is saved to a temporary file. By default, its level 3. Export Log: Click to export temporary system log file to local PC. 4.6.4.PCAP Go to Upgrade - Advanced to start, stop packets capturing or to export captured packet file. Start: To start capturing all the packets file sent or received from phone. Stop: To stop capturing packets. Figure 4.6.3 System log Figure 4.6.4 PCAP 44 R26B Admin Guide Abbreviations ACS:Auto Configuration Server Auto:Automatically AEC:Configurable Acoustic and Line Echo Cancelers ACD:Automatic Call Distribution Autop:Automatical Provisioning AES:Advanced Encryption Standard BLF:Busy Lamp Field COM:Common CPE:Customer Premise Equipment CWMP:CPE WAN Management Protocol DTMF:Dual Tone Multi-Frequency DHCP:Dynamic Host Configuration Protocol DNS:Domain Name System DND:Do Not Disturb DNS-SRV:Service record in the Domain Name System FTP: File Transfer Protocol GND: Ground HTTP: Hypertext Transfer Protocol HTTPS: Hypertext Transfer Protocol Secure IP: Internet Protocol ID: Identification IR: Infrared LCD: Liquid Crystal Display LED: Light Emitting Diode MAX: Maximum POE: Power Over Ethernet PCMA: Pulse Code Modulation A-Law PCMU: Pulse Code Modulation -Law 1 R26B Admin Guide PCAP: Packet Capture PNP: Plug and Play RFID: Radio Frequency Identification RTP: Real-time Transport Protocol RTSP: Real Time Streaming Protocol MPEG: Moving Picture Experts Group MWI: Message Waiting Indicator NO: Normal Opened NC: Normal Connected NTP: Network Time Protocol NAT: Network Address Translation NVR: Network Video Recorder SIP: Session Initiation Protocol SNMP: Simple Network Management Protocol STUN: Session Traversal Utilities for NAT SNMP: Simple Mail Transfer Protocol SDMC: SIP Devices Management Center TR069: Technical Report069 TCP: Transmission Control Protocol TLS: Transport Layer Security TFTP: Trivial File Transfer Protocol UDP: User Datagram Protocol URL: Uniform Resource Locator VLAN: Virtual Local Area Network ONVIF: Open Network Video Interface Forum WG: Wiegand 2 R26B Admin Guide Contact us For more information about the product, please visit us atwww.akuvox.com or feel free to contact us by Sales email: sales@akuvox.com Technical support email: techsupport@akuvox.com Telephone: +86-592-2133061 ext.7694/8162 We highly appreciate your feedback about our products. 3
1 | Authorization letter | Cover Letter(s) | 246.22 KiB | January 13 2020 |
Company: AKUVOX (XIAMEN) NETWORKS CO., LTD. Add: 10/F, No.56, Software Park II, Xiamen, China Tel: 086-0591-83057798 Fax: 086-0591-83057798 E-mail: yang@akuvox.com
( Date:2019-11-26) FCC Authorization FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:
We, AKUVOX (XIAMEN) NETWORKS CO., LTD., hereby authorizes Bay Area Compliance Laboratories Corp. to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature:
Print name: Bo Yang Title: Manager QA-FR-170-B 7/29/2014
1 | Confidential Authorization | Cover Letter(s) | 312.39 KiB | January 13 2020 |
Company: AKUVOX (XIAMEN) NETWORKS CO., LTD. Add: 10/F, No.56, Software Park II, Xiamen, China Tel: 086-0591-83057798 Fax: 086-0591-83057798 Mail: yang@akuvox.com FCC Confidential Authorization Date: 2019-11-26 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AHCR-R26B In accordance with Sections 0.457 and 0.459 of the Commissions Rules, AKUVOX (XIAMEN) NETWORKS CO., LTD. hereby requests long-term confidential treatment of information accompanying this application as outlined below:
Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature:
Print name: Bo Yang Title: Manager QA-FR-171-A
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2020-01-13 | 13.56 ~ 13.56 | DXX - Part 15 Low Power Communication Device Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2020-01-13
|
||||
1 | Applicant's complete, legal business name |
AKUVOX (XIAMEN) NETWORKS CO., LTD.
|
||||
1 | FCC Registration Number (FRN) |
0025226762
|
||||
1 | Physical Address |
10/F, No.56, Software Park II
|
||||
1 |
Xiamen, N/A
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
b******@baclcorp.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
2AHCR
|
||||
1 | Equipment Product Code |
R26B
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
B****** Y******
|
||||
1 | Telephone Number |
086-0********
|
||||
1 | Fax Number |
086-0********
|
||||
1 |
y******@akuvox.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DXX - Part 15 Low Power Communication Device Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Door Phone | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bay Area Compliance Laboratories Corp. (Kunshan)
|
||||
1 | Name |
M**** C********
|
||||
1 | Telephone Number |
+86 0********
|
||||
1 |
q******@baclcorp.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 13.56 | 13.56 | |||||||||||||||||||||||||||||||||||||
1 | 2 | 15C | 0.125 | 0.125 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC