FCC ID: 2ANOT-203532 Wireless Network Control

Important Instructions Subject: Wireless Network Control Ratings: 12VDC Equipment Radio Type IEEE 802.15.4 Radio Frequency Band 2.4GHz ISM Band Frequency of Operation 2405 2475 MHz WARNING Kit consists of:

This kit is to be installed in accordance with the manufacturers instructions and all codes and re-

quirements of the authority having jurisdiction. In Canada, this conversion/installation shall be carried out in accordance with the requirements of the pro-

vincial authorities having jurisdiction and in accord-

ance with the requirements of the CAN/CGA-B149.1 and CAN/CGA-B149.2 installation code. Failure to follow instructions could result in serious injury, death or property damage. The qualified agency per-

forming this work assumes all responsibility for this kit installation. 1 1 2 2 1 1 1 1 W013R4 WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death:

Disconnect electric power to the machine before Close gas shut-off valve to the machine before Close steam gate valve to the machine before servicing. servicing. servicing. removed. Whenever ground wires are removed during serv-

icing, these ground wires must be reconnected to ensure that the machine is properly grounded. 203532 Wireless Networ Cont k rol F8674006 Wireless Network Harness D503661 Screws 55881 Wire Ties XXXXXX Conversion Label F8673901 Network Option Diagram XXXXXX Wireless Control Label 8-18-253EN Kit Instructions Special Tools required for this kit:

Magnetic 5/16 in. Socket IMPORTANT: This kit must be installed by a qualified service person. NOTE: Refer to appropriate service manual to aid in the installation of this kit. IMPORTANT: When reference is made to directions

(right or left) in this instructions, it is from operator's position facing front of machine. CAUTION W017 Changes or modifications not expressly approved could void your authority to use this equipment . This device complies with Part 15 of the FCC Rules. Operation to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer-

Never start the machine with any guards/panels FCC COMPLIANCE STATEMENT Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT 1 Form No. 8-18-253EN October 2018 ence received, including interference that may cause undesired operation. IMPORTANT: Be careful not to damage control panel overlay when prying up tabs. INDUSTRY CANADA STATEMENT Topload Washer Illustrated 1 1. Do Not Bend Figure 2 TLW1683K 4. Adjust the compliance jumpers on the 203532 Wireless Network Control. Refer to Compliance Jumper (H1) section at the end of these instructions. 5. 6. Remove double sided tape backing from 203532 Wireless Network Control. Position 203532 Wireless Network Control so that the mounting tabs on the Network Board go in front of the tabs on the control panel and the assembly mounts to the right of the mounting tabs, as shown in Figure 3 . (The control should be to the right of the mounting tabs.) Then attach using the (2) D503661 Screws. Refer to Figure 3 . This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada ap-

plicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit ac-

cepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. NOTE: When installing this component, all requirements of the mentioned standard must be fulfilled. Also, 203532 is a built-in component and suitable enclosure should be provided in end system. Rear Control Single Washer or Dryer 1. IMPORTANT - Disconnect electrical power to machine. Control will not recognize network board until power is cy-

cled to machine. 2. Remove two control panel attaching screws and lay assembly forward on protective padding. NOTE: There are four tabs located on backside of con-

trol panel frame. Only the two tabs closest to the con-

trol must be bent upward. Refer to Figure 1 and Figure 2 . 1 2 3 TLW1682K 1. Screwdriver 2. Pliers 3. Tabs Figure 1 Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT 2 Form No. 8-18-253EN 3. Use a flat blade screwdriver and slightly bend each tab up on-

ly far enough to allow getting the jaws of a pliers under each tab and bend to 90 degrees. Make sure each tab is bent up square and straight. Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT 3 Form No. 8-18-253EN 7. Install F8674006 Wireless Network Harness between network board "H3" and the electronic control "H1". Refer to Figure 4 . 8. Secure the F8674006 Wireless Network Harness using the (2) 55881 Wire Ties as shown in Figure 4 . 9. Place F8673901 Network Option Diagram in control cabinet 10. Place XXXXXX Wireless Control Label in the control hood with existing diagrams. be-hind the control panel. 11. Fill out and place XXXXXX Conversion Label in control hood behind control panel. 12. Reconnect electrical power to the machine. NOTE: The machine control MUST have been powered down prior to connecting the wireless control in order for the control to recognize the board and to allow communication with it. 1 1. D503661 Screws Figure 3 Topload Washer Illustrated TLW1680K_SVG 1. "H1"

2. 55881 Wire Ties 3. "H3"

4. 203532 Wireless Network Control 5. F8674006 Wireless Network Harness 6. Electronic Control Figure 4 Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT 4 Form No. 8-18-253EN Washer Illustrated 1 2 Front Control 1. IMPORTANT - Disconnect electrical power to machine. Control will not recognize network board until power is cy-

cled to machine. 2. Open access panel to gain access to the control area. Refer to Service Manual. 3. Adjust the compliance jumpers on the 203532 Wireless Net-

work Control. Refer to Compliance Jumper (H1) section at the end of these instructions. Install the F8674006 Wireless Network Harness between the network board "H3" refer to Figure 6 , and the electronic con-

trol "H1". Refer to Figure 7 . Remove double sided tape backing from 203532 Wireless Network Control. 4. 5. 6. Place the tab on 203532 Wireless Network Control into slot in front bulkhead and secure opposite end with one D503661 Screw. Refer to Figure 5 . Washer Illustrated 4 3 FLW226K_SVG 1. Electronic Control 2. "H1"

3. "H3"

4. F8674006 Wireless Network Harness Figure 6 1. 203532 Wireless Network Control 2. Slot 3. D503661 Screw Figure 5 Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT 5 Form No. 8-18-253EN Washer Illustrated D503661 Screw. Refer to Figure 8 . Repeat for installing sec-

ond network board. 1 2 3 1 2 1. Electronic Control 2. "H1"

3. F8674006 Wireless Network Harness Figure 7 FLW227K 4 3 SWD273K_SVG 1. 203532 Wireless Network Control 2. Slot 3. D503661 Screws Figure 8 6. Install F8674006 Wireless Network Harness between network board "H3", refer to Figure 9 , and electronic control "H1". Refer to Figure 10 . 1 2 3 7. Place F8673901 Network Option Diagram in control cabinet 8. Place XXXXXX Wireless Control Label in control cabinet with existing diagrams. be-hind control panel. 9. Fill out and place XXXXXX Conversion Label in control cabinet located behind control panel. 10. Close access panel. 11. Reconnect electrical power to the machine. NOTE: The machine control MUST have been powered down prior to connecting the wireless control assem-

bly in order for the control to recognize the board and to allow communication with it. Front Control 1. IMPORTANT - Disconnect electrical power to machine. Control will not recognize network board until power is cy-

cled to machine. 2. Open access panel to gain access to the control area. Refer to Service Manual. 5 4 SWD274K_SVG 3. Adjust the compliance jumpers on the 203532 Wireless Net-

work Control. Refer to Compliance Jumper (H1) section at the end of these instructions. 4. Remove double sided tape backing from 203532 Wireless 1. "H3"

2. Electronic Control 3. "H3"

4. F8674006 Wireless Network Harness Network Control. 5. Place tab on 203532 Wireless Network Control into slot in front bulkhead and secure opposite end with one Figure 9 Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT 6 Form No. 8-18-253EN 7. Add one 55881 Wire Tie to backside of electronic control as 8. Place F8673901 Wiring Diagram in control cabinet with ex-

shown in Figure 10 . isting diagrams. cabinet. 9. Place XXXXXX Wireless Control Label in the control 10. Fill out and place XXXXXX Conversion Label in control cabinet located behind control panel. 11. Reconnect electrical power to the machine. NOTE: The machine control MUST have been powered down prior to connecting the wireless control assem-

bly in order for the control to recognize the board and to allow communication with it. NOTE: Refer to network installation manual for ma-

chine connections to network. 2 3 1 7 1. Electronic Control 2. Tape 3. "H1" Connection 4. F8674006 Wireless Network Harness 5. 55881 Wire Tie 4 5 6 SWD275K Figure 10 Compliance Jumper (H1) The compliance jumper is used to enforce limits set by local agencies on WiFi channel usage and output power. This jumper must be placed on the pins described in this section that corre-

spond to the location where the Wireless Network Control will be operated. If the jumper is set incorrectly, the Wireless Network Control will be out of compliance with local agencies. If the jumper is not set at all, the Wireless Network Control will operate Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT 7 Form No. 8-18-253EN at a reduced power-level, which will reduce the performance of the Wireless Network Control. NOTE: It is the responsibility of the installer to make sure that the Compliance Jumper is set to meet local standards. Incorrect settings will cause the board to be out of compliance and may lead to reduced range and loss of WiFi channels. Figure 11 Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT 8 Form No. 8-18-253EN Federal Communications Commission (FCC) Interference Statement THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. For additional hosts other than the specific host originally granted with a limited module, a Class II permissive change is required on the module grant to register the additional host as a specific host also approved with the module. The host must meet the necessary requirements to satisfy the module limiting conditions: shield and power supply regulation. The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring the end user has no manual instructions to remove or install module. Regulatory Module Integration Instructions This module has been granted modular approval for mobile applications. OEM integrators for host products may use the module in their final products without additional FCC / IC (Industry Canada) certification if they meet the following conditions. Otherwise, additional FCC / IC approvals must be obtained. The host product with the module installed must be evaluated for simultaneous transmission requirements. The users manual for the host product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC / IC RF exposure guidelines. To comply with FCC / IC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only exposure condition must not exceed as below:

Antenna Type Frequency Band (MHz) Max Antenna Gain (dBi) Dipole Antenna 2405 ~ 2475 2 A label must be affixed to the outside of the host product with the following statements:

This device contains FCC ID: 2ANOT-203532 This equipment contains equipment certified under IC: 23166-203532 The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. If the final host / module combination is intended for use as a portable device (see classifications below) the host manufacturer is responsible for separate approvals for the SAR requirements from FCC Part 2.1093 and RSS-102. Device Classifications Since host devices vary widely with design features and configurations module integrators shall follow the guidelines below regarding device classification and simultaneous transmission, and seek guidance from their preferred regulatory test lab to determine how regulatory guidelines will impact the device compliance. Proactive management of the regulatory process will minimize unexpected schedule delays and costs due to unplanned testing activities. The module integrator must determine the minimum distance required between their host device and the users body. The FCC provides device classification definitions to assist in making the correct determination. Note that these classifications are guidelines only; strict adherence to a device classification may not satisfy the regulatory requirement as near-body device design details may vary widely. Your preferred test lab will be able to assist in determining the appropriate device category for your host product and if a KDB or PBA must be submitted to the FCC. Note, the module you are using has been granted modular approval for mobile applications. Portable applications may require further RF exposure (SAR) evaluations. It is also likely that the host / module combination will need to undergo testing for FCC Part 15 regardless of the device classification. Your preferred test lab will be able to assist in determining the exact tests which are required on the host / module combination. FCC Definitions Portable: (2.1093) A portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is / are within 20 centimeters of the body of the user. Mobile: (2.1091) (b) A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitters radiating structure(s) and the body of the user or nearby persons. Per 2.1091d(d)(4) In some cases (for example, modular or desktop transmitters), the potential conditions of use of a device may not allow easy classification of that device as either Mobile or Portable. In these cases, applicants are responsible for determining minimum distances for compliance for the intended use and installation of the device based on evaluation of either specific absorption rate (SAR), field strength, or power density, whichever is most appropriate. Simultaneous Transmission Evaluation This module has not been evaluated or approved for simultaneous transmission as it is impossible to determine the exact multi-transmission scenario that a host manufacturer may choose. Any simultaneous transmission condition established through module integration into a host product must be evaluated per the requirements in KDB447498D01(8) and KDB616217D01,D03 (for laptop, notebook, netbook, and tablet applications). These requirements include, but are not limited to:

Transmitters and modules certified for mobile or portable exposure conditions can be incorporated in mobile host devices without further testing or certification when:

The closest separation among all simultaneous transmitting antennas is >20 cm, Antenna separation distance and MPE compliance requirements for ALL simultaneous transmitting antennas have been specified in the application filing of at least one of the certified transmitters within the host device. In addition, when transmitters certified for portable use are incorporated in a mobile host device, the antenna(s) must be >5 cm from all other simultaneous transmitting antennas. All antennas in the final product must be at least 20 cm from users and nearby persons. Or

APPLY ESSENTIA P/N 470168 OR 3M 4932 DOUBLE SIDED FOAM TAPE IN THIS LOCATION 50 48 Hono n wills sah UT l YP gee TF A px Ap ee 4 A a] A Co |

Us {I wu Ou ssowretes . Ef | Io L qT tt Ant O subs ti S l aD , Ht cy 5 le C11,2+6, 3] = Ge oO _ Y ea? | po Chee

| : Teal z (

ea oe Hl e ?

ENNA CABLE WIRE MUST~~

BE ROUTED AS SHOWN Label Model / Modelo / Modle / #!5 : 203532 I . Wireless Network Control / Control de red inalambrica/ XXXXXXXX J Alliance Commande via rseau sans fil / 702 2442 Hl a5 = yee FCC ID: 2ANOT-203532 IC: 23166-203532 ICES-3(B)/NMB-3(B) WOM=t eo) CMIIT ID: 2019XXXXXX

: mus NYCE Type-Approval No. IFETEL: xxxxxxXXX-XXXX & ANATEL OOO MoMC R] xxXXXXXXXX XXXXXXXXXX XXXXXXXXXX A\ WARNING:

Cancer and Reproductive Harm Complies with CNE www.P65Warnings.ca.gov. IMDA Standards CNC ID: XXXXX DB106849 , Input: 12VDC;0.8A Made in Mexico / Hecho en Mxico / Fabriqu au Mexique / 3879 = rill i XXXXX

ConfidentialityRequestLetter FederalCommunicationsCommission AuthorizationandEvaluationDivision FCCID:2ANOT203532 ConfidentialityRequest PursuanttoSections0.457and0.459oftheCommissionsRules,weherebyrequestconfidential treatmentofinformationaccompanyingthisapplicationasoutlinedbelow:

Theabovematerialscontaintradesecretsandproprietaryinformationnotcustomarilyreleased tothepublic.Thepublicdisclosureofthesemattersmightbeharmfultotheapplicantand provideunjustifiedbenefitstoitscompetitors. TheapplicantunderstandsthatpursuanttoRule0.457,disclosureofthisapplicationandall accompanyingdocumentationwillnotbemadebeforethedateoftheGrantforthisapplication. 1. BlockDiagram 2. Schematics 3. OperationalDescription Sincerely, _________________ Name:CherylWhite AllianceLaundrySystemsLLC Date:20200226

Request for Modular/Limited Modular Approval Date: September 8, 2020 Subject: Manufacturers Declaration for - Modular Approval Confidentiality Request for: ______ FCC ID: 2ANOT-203532____

- Limited Modular Approval - Limited Split Modular Approval

- Split Modular Approval For Items Marked NO(*), the Limited Module Description Must be Filled Out on the Following Pages Modular Approval Requirement Requirement Met 8 Basic Requirements FCC Part 15.212(a)(1) 1. The modular transmitter must have its own RF shielding. This is intended to ensure that the module does not have to rely upon the shielding provided by the device into which it is installed in order for all modular transmitter emissions to comply with FCC limits. It is also intended to prevent coupling between the RF circuitry of the module and any wires or circuits in the device into which the module is installed. Such coupling may result in non-compliant operation. The physical crystal and tuning capacitors may be located external to the shielded radio elements. 15.212(a)(1)(i) 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with FCC requirements under conditions of excessive data rates or over-modulation. 15.212(a)(1)(ii) Details: The EUT has buffered data inputs, it is integrated in chip (CC2520)

- YES - NO(*)

- YES - NO(*) 3. The modular transmitter must have its own power supply regulation on the module. This is intended to ensure that the module will comply with FCC requirements regardless of the design of the power supplying circuitry in the device into which the module is installed. 15.212(a)(1)(iii) Details: The module contains its own power supply regulation. Please refer to schematic filed with this application

- YES - NO(*) 4. The modular transmitter must comply with the antenna and transmission system requirements of 15.203, 15.204(b), 15.204(c), 15.212(a), and 2.929(b). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph 15.212(b). 15.212(a)(1)(iv) Details: The modular transmitter complies with the antenna requirements. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified or commercially available (see Section 15.31(i)). 15.212(a)(1)(v)

- YES - NO(*)

- YES - NO(*) Details: The modular transmitter is tested in a stand-alone configuration. 6. The modular transmitter must be labeled with its own FCC ID number, or use an electron display (see Modular Approval Requirement Requirement Met KDB Publication 784748). If using a permanently affixed label with its own FCC ID number, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID:

XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. 15.212(a)(1)(vi) Details: There is a label on the module as shown in the labeling exhibit filed with this application.

- YES - NO(*) 7. The modular transmitter must comply with all specific rule or operating requirements applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 15.212(a)(1)(vii) Details: The module complies with FCC Part 15C requirements. Instructions to the OEM installer are provided in the installation manual filed with this application.

- YES - NO(*) 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. 15.212(a)(1)(viii) Details: The modular transmitter complies with applicable RF exposure requirements

- YES - NO(*) Sincerely, By:

(Signature) ______Cheryl White ________________

(Print name)

DeclarationofAuthorization We Name:AllianceLaundrySystemsLLC Address:POBox990,ShepardSt.,Ripon,Wisconsin54971,UnitedStates NameRepresentativeofagent:

MarlinChen AgentCompanyname:

MRTTechnology(Suzhou)Co.,Ltd D8Building,YouxinIndustrialPark,No.2Tian'edangRd., WuzhongEconomicDevelopmentZone, Suzhou China isauthorizedtoapplyforCertificationofthefollowingproduct(s):

WirelessNetworkControl 2ANOT203532 203532 Declarethat:

Address:

City:

Country Product:

FCCID:

Model:

Brand:

Sincerely, __________________ Name:CherylWhite AllianceLaundrySystemsLLC Date:20200226