FCC ID: 2AOKB-T8113V eufyCam 2C

QUICK START GUIDE EUFYCAM 2C WIRE-FREE HD SECURITY CAMERA SET Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. 51005001739 V04 TABLE OF CONTENTS Getting Started Product Overview Connecting the HomeBase 2 Settinging Up the System 01 02 03 04 05 09 10 Mounting the Camera Charging eufyCam 2C Safety Statement 1 GETTING STARTED 2 PRODUCT OVERVIEW For HomeBase 2 installation HomeBase 2 HomeBase 2

(T8010) Power Adapter for HomeBase 2 Ethernet Cable Metal Pin for Resetting For eufyCam 2C installation eufyCam 2C

(T8113V) Micro-USB Charging Cable Mounting Bracket Mounting Screws and Anchors 1 2 3 7 4 5 6 1. Status LED 2. Speaker 3. Power port 4. USB port 5. Ethernet port 6. SYNC/ALARM OFF button 7. Reset button eufyCam 2C 1 2 3 7 6 5 4 8 9 10 1. Camera quantity and accessories vary by bundle package. 2. HomeBase 2 power adapter varies by region. 01 5. Spotlight 1. Lens 6. Status LED 2. Light sensor 3. Microphone 7. SYNC button 8. Mounting hole 4. Motion sensor 9. Charging port 10. Speaker 02 3 CONNECTING THE HOMEBASE 2 44 SETTING UP THE SYSTEM Connect the HomeBase 2 to the Internet Download the App and Set up the System 1. Power on the HomeBase 2, then use the ethernet cable provided to connect the HomeBase 2 to your home router. Download the Eufy Security app from the App Store (iOS devices) or Google Play (Android devices). 2. The LED indicator turns blue (this may take up to 1min) when HomeBase 2 is ready for setup. Sign up for a Eufy Security account, then follow the onscreen instruc-

tions to complete the setup. 03 04 Select Height and Location Hang eufyCam 2C 7-10 ft (2-3 m) above the ground. This height maximizes the detection range of the motion sensor of eufyCam 2C. Avoid placing eufyCam 2C under direct sunlight. 5 MOUNTING THE CAMERA Find a Good Mounting Spot To find a spot to mount eufyCam 2C, you need to test wireless signal strength. Open the Eufy Security app, go to Camera Settings > Mounting Guide. To test the wireless signal strength, take your camera and phone to the location where you want to mount the camera. Move the camera as close to the HomeBase 2 as possible if the wireless signal strength is poor. Camera field Camera field of view of view t f 0 1

7

) m 3

2

Motion Motion Detection Detection Zone Zone Up to 30 ft (10 m) 05 06 Mount the camera Mount the camera The camera can be mounted both indoors and outdoors. 1. Turn the knob of the mounting bracket clockwise to loosen and disassemble it. 3. Firmly screw the base of the mounting bracket onto the wall. Fasten the ball knob of the bracket to the base of the bracket. 2. Drill holes with a 15/64 inch (5.95mm) drill bit, then insert the anchors into the holes; anchors are necessary for walls that are made out of hard materials such as concrete, brick, or stucco. 4. Tighten eufyCam 2C to the mounting bracket and adjust the viewing angle by checking the live stream feed in the Eufy Security app. 07 08 Tips:

1.The Homebase 2 pairs up to 16 cameras, you can repeat the steps mentioned above to add more eufyCam 2C cameras to meet different needs of use. 2. For troubleshooting, check Help on the Eufy Security App. Refer to App page for LED indicator status. 6 CHARGING EUFYCAM 2C Charge eufyCam 2C Method 1 Method 2 5V USB Charger LED indication Charging: Steady blue Fully chargedOff Charging time 5 hours 09 7 SATETY STATEMENT FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help. FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. The following importer is the responsible party Company Name: POWER MOBILE LIFE, LLC Address: 10900 NE 8th St, Ste 501, Bellevue WA 98004 Telephone:1-800-988-7973 This product complies with the radio interference requirements of the European Community. Declaration of Conformity Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site https://uk.eufylife.com/. This product complies with the radio interference requirements of the United Kingdom 10 d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil nedoit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement."

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. IC RF Statement:

When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matire d'exposition RF. Declaration of Conformity Hereby, Anker Innovations Limited declares that this device is in compliance with Radio Equipment Regulations 2017(SI 2017/1206). The full text of the UK declaration of conformity is available at the following internet address: https://uk.eufylife.com. Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher. The adapter shall be installed near the equipment and shall be easily accessible. Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment. The suitable temperature for HomeBase 2 and accessories is -10C-45C. The suitable temperature for eufyCam 2C and accessories is -20C-50C. When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with a temperature that ranges from 5C~25C. Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may cause danger and violate the authorization of the device and the guarantee article. This charger is for indoor use only The charger type is KA2401A-1202000DE, output voltage/current is 12Vdc/2A. The plug considered as disconnect device of adapter. RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 11 For HomeBase 2:

Wi-Fi Operating Frequency Range:

2412~2472MHz; Wi-Fi Max Output Power:18.23dBm(EIRP) SUB-1G Frequency range: 866~866.8MHz;

SUB-1G Output Power: 5.24dBm(EIRP) For eufyCam 2C:

Wi-Fi Operating Frequency Range:

2412~2472MHz; Wi-Fi Max Output Power:

18.83dBm(EIRP) The following importer is the responsible party

(contract for EU matters):

Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807 Munich, Germany The following importer is the responsible party

(contract for UK matters):

Anker Technology (UK) Ltd I Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom This product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product. IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device."

Le prsent appareil est conforme aux CNR 12 8 LEGAL NOTICE Use of the Works with Apple HomeKit badge means that an electronic accessory has been designed to connect specifically to iPod touch, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Customer Service Warranty 12-month limited warranty Call Us United States +1 (800) 988 7973 Mon-Fri 9AM-5PM (PT) United Kingdom +44 (0) 1604 936 200 Mon-Fri 6AM-11AM (GMT) Germany +49 (0) 69 9579 7960 Mon-Fri 6:00-11:00 Email Us Customer Support: support@eufylife.com Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

@EufyOfficial

@EufyOfficial

@EufyOfficial 13

Anker Innovations Limited Date: 2022/10/13 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland MillsRoad, Columbia, MD 21046 To Whom It May Concern:

The Anker Innovations Limited, the undersigned, hereby authorizes Mrs. Wendy Zhan from Shenzhen Morlab Communications Technology Co., Ltd., to act on the behalf of the Anker Innovations Limited solely in matters relating to the application for an FCC equipment authorization for FCC ID: 2AOKB-T8113V including the signing of documents in connection with this Application. Necessary acts carried out Shenzhen Morlab Communications Technology Co., Ltd. on our behalf of the Anker Innovations Limited in connection with the application shall have the same effect as acts of the Anker Innovations Limited. Anker Innovations Limited also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Thank you for your attention to this matter. Yours Sincerely, Signatory:

Contact name: Louis Qi Tel:++86-755-86544807 Email:Louis.qi@anker.com Company name: Anker Innovations Limited

Anker Innovations Limited Date: 2022/10/13 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re:

Request of Confidentiality for FCC ID: 2AOKB-T8113V To Whom it may concern:

Pursuant to sections 0.457 and 0.459 of Commissions Rules(CFR 47), and Section 552(b)(4) of the Freedom of Information Act, Anker Innovations Limited hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality (max time 180 days from grant date) as outlined in Public Notice DA04-1705. This provision will give Anker Innovations Limited temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Short-Term Confidential exhibits are listed as follows:

PERMANENT AND SHORT-TERM CONFIDENTIAL LIST PERMANENT SHORT-TERM Exhibit 1 2 3 4 5 6 7 8 Description Block Diagram Operational Description Schematics BOM External Photos Internal Photos Test-Setup Photos User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Signatory Name: Louis Qi Company Name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Tel: +86-755-86544807 Email: Louis.qi@anker.com