User Manual Motion Sensor Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. Model: T8910 51005002023 V01 TABLE OF CONTENTS Whats Included 02 10 Specifications Product Overview 03 11 Notice Mounting the Motion Sensor 05 14 Customer Service English 01 WHATS INCLUDED For Motion Sensor Installation PRODUCT OVERVIEW Battery Compartment Motion Sensor T8910 Mounting Screws User Manual LED Indicator Motion Sensor SYNC Button Installing Batteries Welcome Card CR123A Battery 3M Adhesive Strip Remove the battery compartment lid on the Motion Sensor and insert the provided CR123A battery. Mount 02 English English 03 Adding Motion Sensor to Your System 3. The LED indicator turns solid blue to indicate the pairing is successful. Note: Make sure you've completed the setup of your eufy Security HomeBase. Follow the onscreen instructions on the Eufy Security app to add your motion sensor. 1. Choose Add Device, then select Motion Sensor to add it to your system. LED Status Description Blinking blue continuously Waiting to connect Solid blue for 5s Paired successfully Off Failed to connect to the HomeBase 2. Press and hold the SYNC button for 2 seconds until the LED indicator blinks blue. The Motion Sensor is waiting to pair. Note: The LED indicator, device name and timer can be customized on the eufy Security app. MOUNTING THE MOTION SENSOR Find a Location for Mounting The motion sensor can be installed on a wall. To get optimal detection coverage, consider the following factors before mounting the motion sensor:
Determine the area of detection and ensure there is an unobstructed field of view Determine the height and tilt angle Avoid direct sources of heat or sunshine, curtains, plants, or pets. Ideally, the motion sensor should be installed on a wall facing the door through which people are likely to enter. We recommend placing the motion sensor close to a corner to get the optimal detection coverage. 04 English English 05 No Pets 20 m 5 2
2
. You can also install the motion sensor in your garage, dining room, or basement. Height and Tilt Angle To better detect the area where people may break in, rotate the motion sensor horizontally up to 30. The motion sensor should be mounted 2m / 6/ ft to 2.5m / 8 ft above the floor with a tilt angle of preferably 20 downwards. If you have a large pet weighing more than 50 lb, change to a 10 downwards tilt. Sensitivity The sensitivity can be adjusted based on the room size. The default setting is medium sensitivity. With Pets 10 m 5 2
2
. 06 English English 07 Mount the Motion Sensor 1. There are two methods of mounting the motion sensor at the selected location:
Use the 3M adhesive strip:
Snap the adjustable wall mount onto the motion sensor base. Stick the adhesive strip on the back of the sensor, remove the film, and stick the motion sensor on the wall. Rotate the motion sensor to adjust the detection coverage. 1 2 Drill holes at each marking. No need to drill a pilot hole in the wooden walls. Insert anchors into the holes, and fix the mount onto the wall with the provided screws. No anchors are needed on wooden walls. Place the mount against the wall and use a pencil to mark the desired Use the provided screws:
location for mounting. 08 English Clip the motion sensor back onto the mount. Rotate the motion sensor to adjust the detection coverage. English 09 Replace the Battery When the motion sensors battery is low, the LED indicator shows as below. ou should replace the battery to keep the motion sensor working. LED Status Blinking blue Blinking red Description Movement detected while the HomeBase is connected Movement detected while the HomeBase is not connected SPECIFICATIONS Battery: 1 CR123A battery Operating Temperature: -10C - 40C /14F - 104F Storage Temperature: -20C - 60C /-4F - 140F Use the Motion Sensor After the motion sensor is installed, the alarm will be triggered once movement is detected within the motion sensors coverage area. When the motion sensor is working, its LED indicator shows as below:
LED Status Blinking blue Blinking red Description Movement detected while the HomeBase is connected Movement detected while the HomeBase is not connected When the motion sensor is in the test mode, the LED indicator shows as below:
LED Status Solid red Description Enter the test mode successfully Blinking red for 1 second Movement detected when the motion sensor is in the test mode Off Failed to enter the test mode 10 English English 11 NOTICE FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/ TV technician for help. FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed / mobile exposure condition. The min separation distance is 20cm. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. The following importer is the responsible party. Company Name: POWER MOBILE LIFE, LLC Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541 Telephone: 1-800-988-7973 This product complies with the radio interference requirements of the European Community. 12 English Declaration of Conformity Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit www.eufylife.com. Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment. The suitable temperature for the product and accessories is -10C-40C. RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and the human body. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS SUB-1G Frequency range: 866~866.8MHz (for EU) ; 920~920.8MHz (for US) Max Output Power: 6.496dBm (ERIP) This product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product. IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device."
Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si English 13 le brouillage est susceptible d'en compromettre le fonctionnement."
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. CUSTOMER SERVICE IC RF Statement Warranty When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matire d'exposition RF. FCC ID: 2AOKB-T8910 IC: 23451-T8910 Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong 12-month limited warranty
+1 (800) 988 7973 Mon-Fri 9AM-5PM (PT)
+44 (0) 1604 936 200 Mon-Fri 6AM-11AM (GMT)
+49 (0) 69 9579 7960 Mon-Fri 6:00-11:00 Customer Support: support@eufylife.com 14 English English 15