FCC ID: 2AOKB-A2566A PowerWave Select+ Magnetic Pad

For FAQs and more information, please visit:

anker.com/support

@anker_official

@anker_jp

@Anker Deutschland

@Anker Japan

@Anker

@AnkerOfficial

@Anker_JP Product Number: A2566 51005002807 V01 EN T You cannot charge your device wirelessly when using an ultra-thick (> 4 mm) protective phone case or a case with a pop socket. This wireless charger only supports the protective cases that match the magnetic structure of the iPhone. Do not place any foreign objects between your device and the wireless chargers surface, including metal pads on a car mount, magnetic cards, door keys, coins, NFC cards or other metal objects, as they could potentially demagnetize the wireless charger, affect the charging speed, or cause overheating. Wireless chargers make charging more convenient than wired chargers, but confined by current wireless technology, their charging speed is slower than that of wired chargers. High temperatures will reduce charging speed and restrict power. It is recommended that you charge your device in environments with temperatures below 40C / 104F. Important Safety Instructions the bottom before installing or operating the product. Please refer to the electrical and safety information on Avoid dropping. Do not disassemble. Do not expose to liquids. For the safest and fastest charge, use original or certified cables. This product is suitable for moderate climates only. The maximum ambient temperature during use of this product must not exceed 40C. product. Open flame sources, such as candles, must not be placed on this Only use a dry cloth or brush to clean this product. The socket-outlet shall be installed near the product and shall be easily accessible. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator

& your body. Product Name: PowerWave Select+ Magnetic Pad Model: A2566 The following importer is the responsible party (for FCC matters only). Company Name: Fantasia Trading LLC Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764 Disconnection from line voltage should be made via the AC plug. Telephone: +1 800 988 7973 01 02 IC Statement This device complies with RSS-216 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. RSS-Gen This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF exposure statement:

The equipment complies with IC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This device complies with Industry Canada license-ICES-003. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This digital apparatus complies with CAN ICES-003(B)/NMB-003(B). Declaration of Conformity Hereby, Anker Innovations Limited declares that the product type A2566 is in compliance with Directives 2014/53/EU & 2011/65/

EU. The full text of the EU declaration of conformity is available at the following internet address:

https://www.anker.com/

GB Declaration of Conformity Hereby, Anker Innovations Limited declares that the product type A2566 is in compliance with Radio Equipment Regulations 2017 and 03 The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The full text of the GB declaration of conformity is available at the following internet address:

https://www.anker.com Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Anker Innovations Deutschland GmbH Georg-Muche-Strasse 3, 80807 Munich, Germany Anker Technology (UK) Ltd Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 20mm must be maintained between the users body and the wireless charger, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-

worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. UK Declaration of Conformity Hereby, Anker Innovations Limited declares that the product type A2566 is in compliance with following Directives: Radio Equipment Regulations 2017, Electrical Equipment (Safety) Regulations 2016 and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The full text of the UK declaration of conformity is available at the following internet address:

https://www.anker.com Specifications Input Output 5V 2.4A / 9V 2A / 12V 2A 15W Max (7.5W for iPhone) Operating Temperature

-10 C - 40 C 04 Radiated H-Field

-43.762dB A/m(@10m) TX/RX Frequency Range 110-205KHz (only for EU and UK) This product complies with the radio interference requirements of the European Community. Indoor use only. This symbol indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. 05

A2566 US

浅色

深色

移印（与主体颜色接近）

移印（与主体颜色接近）

制作：Evie

版本：V5

日期：20210701

Shenzhen Qianhai Patuoxun Network & Technology Co., Ltd.

Date: 7/6/2021

Federal Communications Commission

To Whom It May Concern:

The letter grants authorization for representative of Anker Innovations Limited to apply the FCC for

a change in identification. This authorization applies to Shenzhen Qianhai Patuoxun Network &

Technology Co., Ltd., FCC ID: 2AOXY-PA228A, granted on 04/16/2021, The equipment is

electrically identical.

We are aware that Anker Innovations Limited intends to market the above referenced product under

FCC ID: 2AOKB-A2566A

The only changes are applicant, manufacturer and factory name, address, product name,

model number, trademark, product casing, FCC ID and label on equipment, FCC ID and label

on the device.

The original test results, technical information and relevant documents continue to be

representative of and applicable to the change ID equipment.

Should there be any question, please feel free to contact us.

Client’s name / title: Derric Bai / Compliance Manager

Client’s signature：

Tel: 18566621145

Email: Derric_bai@patazon.net

< Anker Innovations Limited >

C5266091_X4_Ed.1

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046

USA

Date: 07/06/2021

Subject:

Reference:

FCC ID: 2AOKB-A2566A

Request for §2.933 Change in identification of equipment

Gentlemen,

Anker Innovations Limited requests a Change in Identification for a currently

approved device. This application will establish a new FCC ID for purpose of

marketing.

The original Grant for Shenzhen Qianhai Patuoxun Network & Technology Co., Ltd.,

under FCC ID: 2AOXY-PA228A with a Grant Date of 04/16/2021 will remain in effect.

An authorization letter from the original Grantee is attached.

We attest that the equipment is electrically identical. only changes are applicant,

manufacturer and factory name, address, product name, model number,

trademark, product casing, FCC ID and label on equipment. are different. The

original test results are applicable and continue to be representative of this device.

The following files are provided as attachments:

• Cover letter giving permission from original Applicant for Change in ID

• External photos showing no physical changes to this device

• New FCC identification label and it’s location.

Thanks and Best Regards,

(New Grantee Signature)

(New Applicant Company) Anker Innovations Limited

(New Applicant Address) Room 1318-19, Hollywood Plaza, 610 Nathan Road,

Mongkok, Kowloon, Hong Kong

(New Applicant phone) +86-13652441319

(New Applicant Email) louis.qi@oceanwing.com

1/1

C5266091_X10_Ed.2

Anker Innovations Limited

Office of Engineering Technology

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046 Date: 7/22/2021

Subject: Request for Confidentiality

FCC ID: 2AOKB-A2566A

To Whom It May Concern,

Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following

attachment(s) as confidential document from public disclosure.

Exhibits

ID Label/Location

Attestation Statement

External Photos

Block Diagram

Schematics

Test Report

Test Setup Photos

User’s Manual

Internal Photos

Parts List / Tune Up

RF Exposure Info

Operational Description

Cover Letter(s)

SDR Software / Security Info

Long-Term

Confidentiality

No

No

No

☐

☐

No

No

☐ NOTE 1

☐ NOTE 1

☐

No

☐

No

☐

Short-Term

Confidentiality NOTE 2

No

No

☒

☐

☐

No

☐

☒

☒

☐

No

☐

No

No

NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of

KDB 726920, use last in force)

NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant.

Above mentioned document contains detailed system and equipment description are

considered as proprietary information in operation of the equipment. The public

disclosure of above documents might be harmful to our company and would give

competitor an unfair advantage in the market.

In case of short-term Confidentiality, the applicant requests the exhibits selected above

are withheld from public view for a period of __180____ days from the date of the Grant

of Equipment Authorization and prior to marketing.

It is our understanding that all measurement test reports, FCC ID label format and

correspondent during certification review process cannot be granted as confidential

documents and those information will be available for public review once the grant of

equipment authorization is issued.

1/1

C5266091_X10_Ed.2

Sincerely,

Signature:

Name: louis Qi

Title:

1/1

C5266091_X8_Ed.1 Letter of Authorization

< Anker Innovations Limited >

2AOKB-A2566A Company: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Product Name: PowerWave Select+ Magnetic Pad Model Number: A2566 FCC Identifier:

We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: louis Qi Title:

Signature of applicant:

Date: 7/6/21 1/1