FCC ID: 2AOKB-R2251 Roav DashCam A0

Anker Innovations Limited. All rights reserved. ROAV and the ROAV logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. Model: R2251 51005000920 V01 Owners Manual Roav DASHCAM A0 Table of Content Safety Instructions At a Glance Inserting Memory Card Installing Your DashCam Connecting to Power Downloading Roav App 01 02 03 04 06 07 Using Your DashCam 08 System Setup Specifications FAQ Notice 10 12 13 14 Safety Instructions Please read and understand all instructions before using this product. If damage is caused by failure to follow the instructions, the warranty does not apply. Keep these instructions. Do not drop, puncture or disassemble this product. This product should not be exposed to dripping or splashing liquids. Avoid long exposure to direct sunlight, which may cause damage to this product. Exposing this product to open flames may cause explosion. Use original accessories only. Do not install where it will block the drivers view of the road or the Keep your attention on the road. Do not operate the controls of this deployment of the airbag. product while driving. Ensure the camera lens is kept clean and there is nothing blocking Setup time and date accurately before using this product. Do not use the charger if the cord is damaged or broken. Do not directly touch the product when it is getting overheated after long exposure to sunlight or continuous work. Remove this product from your vehicle when not in use for a long the lens. period. Keep out of reach of children. Use a clean, soft cloth to clean. Do not use any corrosive cleaner or The Company is NOT responsible for the loss of any data/content oil to clean. during operation. 01 DashCam Suction mount Owners Manual DASHCAM C1 Manual Car charger microSD card Accessories are subject to change without notice. At a Glance Inserting Memory Card Do not remove or insert microSD / TF card when this product is powered on, which may damage the card. For better product experience, use microSD / TF card that is higher than Class 10 32G. Do not use card lower than Class 10 as it may damage the product. Card should be formatted in Dashcam before using. It is recommended to format the card regularly. Card Capacity 32 GB 64 GB 128 GB 1080P 30FPS 320 min 640 min 1280 min 720P 30FPS 480 min 960 min 1920 min Insert a microSD / TF card with the gold contacts facing the screen side of the DashCam. Push the card until it clicks into place. To remove the card, gently push its top edge inward until it clicks, and then pull it out of the slot. 03 Camera lens Power button Reset slot Memory card slot Speaker Microphone LED indicator Flashing blue: recording in progress Steady red: no recording status Air vent Micro USB charging port Buttons LCD screen 02 Installing Your DashCam Never install this product while driving. Install this product near the rear-view mirror to obtain the best open-field view. Do not install in a location that will obstruct your required driving view. Make sure that the lens is within the wiping range of the windscreen wiper to ensure a clear view even when it rains. Do not touch the lens with your fingers. Finger grease may be left on the lens and will result in unclear videos. Attach the DashCam onto the mount. Select a location on the windshield near the bottom right corner of the rear-view mirror, clean with clear water and wait until fully dry. Attach the suction mount onto the windshield and press down the suction clip. Adjust the Dashcam viewing angle to ensure that it is aligned with the road ahead, then rotate the fixing knob to fasten. Hide the charging cable into the seams and weatherstrips around the edge of the dashboard. 04 05 Connecting to Power Downloading Roav App Connect the car charger to the DashCam. Plug the other end of the car charger to your vehicles cigarette lighter socket. Search Roav in App Store or Google Play to Download. Once the car engine is started, DashCam will automatically power on and start recording. Once the car engine is shut down, DashCam will automatically save the recording and turn off. 06 Connect DashCam with Smartphone With successful connection with your smartphone via built-in Wi-

Fi, you can save and playback the driving recording videos on your smartphone. You can also change settings of your DashCam via the Roav app. When successfully connected, DashCam stops recording.

(Menu), select WIFI > On to enable WiFi on Press DashCam. Enable WiFi on your smartphone, find Roav DashCam A0 on the list and connect it, enter password (initial password:

goroavcam) if required. Follow the on-screen instructions in the Roav app to complete the connection.connection. 07 Using Your DashCam Playback Videos As a driver, you have full responsibility to drive safely and adhere to all applicable traffic regulations. Record Videos When connected to a car charger, DashCam automatically starts recording, REC is displayed and red dot flashes on the screen, the current recording duration is displayed, and the current date and time is displayed. To enable / disable the audio recording, press Unmute).

(Mute/

Protect the Current Recording By default, DashCam uses a sensor to automatically detect accidental collisions and protect the video file with duration of 30 seconds. This indicates that those recordings have been locked and will not be overwritten by new video clips. To protect the current recording manually, press

(Emer). The DashCam stops recording while viewing videos or settings. Select Normal folder to check saved videos. Select Event folder to check the videos of accidental collisions. Select a video to playback. Button Virtual Button Function Play / Pause Fast forward Delete Current / Delete All Back to previous menu 08 09 System Setup The OSD functions are subject to change without notice To adjust DashCams settings, tap

. Menu Options Description Set a desired video resolution. Resolution Loop recording Set the duration of each Available Options 720P 30FPS / 1080P 30FPS 1 Min / 3 Min / 5 Min Low / Medium /

High / Off Low / Medium /

High / Off recording video clip. Sensitivity for gravity helps to detect vibration and shock while driving and makes DashCam to respond appropriately. Enable to keep DashCam in standby mode. Motion will be detected for 15 times and DashCam starts recording a 30 second video each time. Connect with smartphone. On / Off Sensitivity Parking mode WIFI Time Setup Set date and time 10

/

Tap the value, press to next option, press to adjust to save None / YYYY MM DD / MM DD YYYY

/ DD MM YYYY 30 Seconds / 60 Seconds / Off On / Off Cancel / OK Cancel / OK Date+Logo / Date /

Logo / Off 50 Hz (EU / China) /

60 Hz (US) Date Format Set the sequence for date. LCD Auto Off Turn off the screen backlight after a period of inactivity. Machine Sound Mute or unmute. Reset all options to the default settings. Format the memory card and all the data will be deleted. Display / hide the date and time on the recordings. Match the video frequency of DashCam with the electrical frequency of your location. Check the current version number. Default Format Water Mark Frequency About Button Function Click repeatedly to select a setting; Click to confirm a selection. Toggle the next setting Toggle the previous setting Back to recording mode 11 Specifications FAQ Specifications are subject to change without notice. 1.5A Screen: 2.4 LCD color TFT Camera lens: wide-angle lens 155 Power input: 5V Max video resolution: 1080P 30FPS (1920x1080) Video clip format: .MP4 Wi-Fi: 2.4GHz Band Operating temperature range: -20C to 70C / -4F to 158F Operating temperature range: 0C~70C/32C~158C (Parking mode) Weight: Approx. 87 g / 3 oz Size: 83.4 * 56 * 35.4 mm / 3.3 * 2.2 * 1.4 in How come the memory capacity in my memory card is not 100% available?

Some memory capacity is used for emergency recording. Can not record?

Check if the memory card is inserted properly and there is enough free capacity. Check the battery level. Blurred image?

Use a clean, soft lens-cleaning cloth to gently clean the lens. Malfunction or crash?

Long press the Reset slot by using a sharp pin for at least 2 Blank screen?

The screen saver is activated. Change settings to Off if seconds. required. Fail to view and playback videos on your smartphone?

Check on your smartphone if Wi-Fi is successfully connected to the DashCam. How to enable parking mode?

Press Worry about the memory card is full?

Continuous loop recording allows to overwrite the old

(Menu) , select Parking mode > ON. Will my data be used when my smartphone is connected with DashCam?

No. Data will be used only if you share the saved videos via unlocked files. social apps. 12 13 Notice FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna.

(2) Increase the separation between the equipment and receiver.

(3) Connect the equipment into an outlet on a circuit different from 14 that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help. This device is acting as slave and operating in the 2.4 GHz (2412-

2462 MHz). FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Google Play and the Google Play logo are trademarks of Google Inc. Android is a registered trademark of Google Inc. in the United States and other countries. iOS is a registered trademark of Apple Inc. other countries. in the United States and IC NOTICE TO CANADIAN USERS This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This 15 Class B digital apparatus complies with Canadian ICES-003 (Cet appareil numrique de la Classe B conforme la norme NMB-003 du Canada). Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. 12-month limited warranty Lifetime technical support support@goroav.com

+1 (800) 988 7973 (US) Mon-Fri 9:00 - 17:00 (PT)

@GoRoav

@GoRoav

Product Name: Roav DashCam A0 Model No.: R2251 FCC ID: 2AOKB-R2251 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: TCB@siemic.com Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Initial Release (obsolete) Revised wording (obsolete) Updated company template (obsolete) Updated letter information (obsolete) Added FCC ID field (current) Revision History To From 1.0 1.0 2.0 1.0 2.0 3.0 4.0 3.0 4.0 5.0 Approved Date Nov-14-2006 Sept25-2007 Jan-31-2012 May-23-2014 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2Rev 5.0

(Anker Innovations Limited)

(2018-03-20) To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, _____Anker Innovations Limited____hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s):

Product description: Roav DashCam A0 Model name: R2251 FCC ID: 2AOKB-R2251 Sincerely, Clients signature louis Qi / Manager Company Name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hongkong Email: louis.qi@oceanwing.com SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2Rev 5.0

WIFI Channel 12 and 13 Declaration Letter Reason for Amendment Initial Release (obsolete) Modify the select options (current) Revision History From Initial 1.0 To 1.0 2.0 Approved Date December 22, 2015 September 23, 2016 SCSF190 WiFi Channel 12&13 Declaration Letter Page 1 of 2 Created by William Graff Rev.2.0 Approved by BaoThuong Nguyen Anker Innovations Limited WIFI Channel 12 and 13 Declaration Letter We declare the equipment identified below with regards to Channel 12 and 13 capabilities for FCC ID: 2AOKB-R2251 Declaration Product hardware does not have the capability to operate on Channel 12 and 13. Product hardware has the capability to operate on Channel 12 and 13. However, these two channels will be disabled via software and will not be accessible to user. Product hardware has the capability to operate on Channel 12 and 13. However, all the operated channels cant be changed in the RF parameter via software. All channels have complied with all of the requirements sets out in FCC Part 15.247. Product hardware has the capability to operate on WiFi Channel 12 and 13, and meets the requirements of KDB 594280 D01 v02r01. Please note:

1.) By default, this device operates in a mode that is compliant with the U.S. requirements. 2.) This device will also use supplemental information such as geo-

location data to determine that it is operating outside the U.S., if necessary, to change its power. Such supplemental data will be derived from the following:

Global Navigation Satellite System (GNSS)7 sensors in the device Mobile Country Code (MCC),8 or MCC with a Mobile Network code

(MNC), received from a CMRS9 carrier and received directly by a receiver on the device Country information derived from multiple adjacent access points (for example using IEEE Std 802.11d provisions) may be permitted on case-by-case basis Other suitable geo-location data based on IP addresses or other reliable source. Name / Title: louis Qi / Manager Signature:

Phone: +86-13652441319 Email: louis.qi@oceanwing.com Date: Mar. 20, 2018 SCSF190 WiFi Channel 12&13 Declaration Letter Page 2 of 2 Created by William Graff Rev.2.0 Approved by BaoThuong Nguyen

775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: TCB@siemic.com Confidentiality Request Letter Reason for Amendment (current / obsolete) Initial Release (obsolete) Adding CFR 2.459 (obsolete) Updated company template & Added text Added IC confidentiality letter form Corrections to STC form. Added reference box (obsolete)

(obsolete) to KDB (current) Revision History To From 1.0 1.0 2.0 1.0 2.0 3.0 Approved Date Nov-14-2006 August 11 - 2008 Jan-31-2012 3.0 4.0 4.0 5.0 March-26-2015 Nov 19 2015 SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 5.0

(Anker Innovations Limited)

(2018-03-20) To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AOKB-R2251 Pursuant to sections 0.457 and 0.459 of CFR 47, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application as:

Block Diagram Schematics

-

-

- Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Clients signature louis Qi / Manager Company Name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hongkong Email: louis.qi@oceanwing.com SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 5.0