1.Do not use a damp cloth to clean or immerse the Cyber Surfer in water for cleansing. Only use a dry cloth to clean off the dust. 2. Do not get the radio controller wet. If the controller accidentally gets wet, remove the battery and allow it to air-dry. Replace with fresh batteries before resuming operation. 3. Do not bend the body of Cyber Surfer as this may affect its performance. (Diagram 'F) 4. Always turn off the Cyber Surfer and controller when it is not in use 5. After about 5-10 minutes of flying time, the speed of Cyber Surfer will Helpful Tips slow down. When the battery is drained, the Cyber Surfer will gradually descend and land. It is time to replace your batteries or to recharge your Cyber Surfer. 6.For best performance, hold the controller antenna upright and pointed toward the Cyber Surfer. If your Cyber Surfer gets too far away, it will not work properly. 7.When the Cyber Surfer flies erratically, the problem is usually the result of interference caused by high tension wires, CB radios, or other R/C vehicles running nearby on the same frequency as yours. You may have to choose an alternative place to play. 8. Do not store the Cyber Surfer or controller near heat, direct sunlight or damp places. 9. When your Cyber Surfer starts to lose power, it Assembly Of The Propellers Please replace the propellers with the extra set provided, IF damaged. The replacement should be done by an adult. may lose functions or performance. It's time for fresh batteries (or a recharge),
. Your Cyber Surfer flying time may vary depending on your flying style. Please note the control distance may vary indoors as the radio signal is affected by lots of obstacles. Keep the Cyber Surfer within 20m of the controller. Fa day or more passes without charging the Cyber Surfer, fully recharge it before playing. Avoid flying the Cyber Surfer during strong winds. You may lose control and it may cause damage after a hard landing. After a hard landing, make sure you turn off and reset your Cyber Surfer. If you experience unusual operation of your Cyber Surfer, make sure you check the regulation. PLEASE READ VERY CAREFULLY BEFORE FITTING NEW PROPELLERS!!!!
Old Propeller Beginner For beginners, it is better to leave the inchs off the Cyber Surfer three Expert Player ground. Adjust the balance of the Cyber Surfer with the Trimming Button until it flies steady and level. Then release your hand and let it fly up. Once your liftoff skills have improved, you can let the Cyber Surfer lift off the ground directly.
*Never let the Cyber Surfer take off at any places apart from the ground. e.g. table, chair or cupboard etc.
- Place the Cyber Surfer on a flat ground, then slowly push Power Lever up.
- Focus on the Cyber Surfer rather than the controller.
- Very gently push the Power Lever up if the Cyber Surfer goes down.
- If the Cyber Surfer has a deflection on either side, remember to regulate the balance before playing. As soon as the Cyber Surfer lifts off the round, release the Power Lever slightly. io not push the Power Lever rapidly, it may go up and crash against the ceiling. Keep holding the Power Lever, and give a few light pushes to the Direction Lever to get your Cyber Surfer to spin. Push the Direction Lever repeatedly until the Cyber Surfer spins. You may also push Power Lever up if it goes down. New Propeller First, lossen the two screws at the bottom of the propeller set. Select a new propeller which is same direction as the old one. For example, if you want to change the propeller on the left side, please select the left Romove the lid and propellers. Lossen the four screws on the top of the propeller set. Place the new propeller(s) back into position as well ry
-/'\ 1) Always follow the 7) instructions carefully. 2)Do not mix old and new batteries or batteries of different types. 3) Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cacdmium) batteries. 4) Use only batteries specified and be sure to insert item correctly by the and polarity markings. Always follow the toy and battery manufacturer's instruction. 5) Remove batteries when not in use. Always temove exhausted batteries from the controller. Dispose batteries safely. 6) Non-rechargeable batteries are not to be recharged.
* Apply white glue to the broken areas and press them back into place. Reinforce with clear cellophane tape. loam Wi adult Supervision to ensure safety.
*DO NOT USE SUPER GLUE. Super pe ire Gales unwanted effects to the ich may result in irreparable damage. Repairs should be done under Battery Caution 8) Cyber Surfer is only to be charged under adult supervision. 9) Only batteries of the same or equivalent type as recommended are to be used. Do not recharge other types of batteries. 10) Do not charge Cyber Surfer for longer than specified in this instruction manual. 11) Never charge the Cyber Surfer when the AC adaptor is wet. 42) Always unplug the wires when not in use. 13) Never leave a rechargeable Cyber Surfer unattended when charging. 14) Rechargeable batteries are not recommended for use in the controller. 15) Never short-circuit the battery terminals. conditions:
harmful interference, and undesired operation. could void the user's authority to operate the equipment. Battery installation should be done by an adult. Troubleshooting Guide If you are experiencing difficulties with the Cyber Surfer, besides calling our customer service hotline, try checking these areas:
propeller. The camber side should faces up. 16) Dispose of old batteries promptly and properly; do not burn or bury them. 17) Do not dispose of batteries in a fire, batteries may explode or leak. 18) Do not disassemble a battery as it may burst and release toxic liquids. 19) Bent or dirty battery contacts may result in loss of power. 20) Should this product cause, or be affected by, local electrical interference, move it away from other electrical equipment Reset (switching off and on again or removing and re-assemblying batteries) if necessary. 21) Charge the Cyber Surfer by using the supplied adaptor only. 22) The battery inside the Cyber Surfer is not replaceable, please do not try to replace the internal battery. This device complies with Part 15 NOTE: This equipment has been tested cause harmful interference to radio of the FCC Rules. Operation is and found to comply with the limits fora or television reception, which can be subject to the following two Class B digital device, pursuant to Part determined by turning the equipment 15 of the FCC Rules. These limits are off and on, the user is encouraged to
(1) This device may not cause designed to protection against harmful interference or more of the following measures:
(2) This device must accept any in a_ residential installation. This interference received, including equipment generates, uses and can interference that may cause fadiate radio frequency energy and, if not installed and used in accordance Caution: Changes or modifications with the instructions, may cause harmful not expressly approved by the interference to radio communications. party responsible for compliance However, there is no guarantee that interference will not occur in a particular installation. If this equipment does provide reasonable try to correct the interference by one
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or experienced Tadio/TV technician for help. Problem Solution LEDs on the Cyber Surfer are dim. 1 Cyber Surfer does not work. The LEDs are not lit but power is turned on or the a) The battery may be drained, Recharge the Cyber Surfer for 70 minutes and try again. a Cyber Surfer is not responding to the controller. a) The contro! distance is too great and out of signal receiving range. Control the Cyber Surfer from less than 20m to make the signal receive. Make sure the antenna of the Radio controller is fully extended. b) There is interference caused by high tension wires, CB radios, or other R/C vehicles running nearby on the same frequency as yours. It is better to choose an alternative place to fly.
) The 9V battery in controller is exhausted, replace with fresh battery. d) Make sure the antenna is tightened. If the antenna were too loosen, then no signal can be transmitted. Screw the antenna tightened. XY 3 Cyber Surfer does not fly or turn properly. | a) The Cyber Surfer may be out of regulation after severe or multiple crashes, improper storage or change of temperature etc. Cyber Surfer needs to be regulated again. b) There may be dust and foreign objects etc. entangling in the propellers of the Cyber Surfer. Check it and make sure it is clean and free of restrictions to allow it to rotate correctly. S/S as the lid. Tighten the four screws on the top of the propeller set. Finally, tighten the two screws at the bottom of the propeller set. Q @
KX CE Waste electrical products/ batteries should not be disposed of with household waste. Separate disposal facilities exist, for your nearest facilities. If there is any problem with Cyber Surfer, please call our customer service hotline: 877-4B2X-USA. Please do not return goods to retail stores directly. For enquiry: info@aok-ltd.com ibuted by B2X Corporation 2008 AOK Ltd ver B, New Mandarin Plaza, 14 Science Museum Road, Tsim Sha Tsui, Kowloon, Hong Kong All Rights Reserved Made in China turn.
* The Cyber Surfer will move forward slowly when a certain level of power is used, while performing a
+ If you want to stop the Cyber Surfer, it is sufficient to give a short counter turning command. For example, when the Cyber Surfer is flying right, give a left push to the Direction Lever to stop flying.
* Aim the Cyber Surfer toward the landing area.
* Reduce speed by slowly releasing the Power Lever. The Cyber Surfer will descend slowly and land. Picking Up Your Cyber Surfer After Flight Make sure young children operate the Cyber Surfer under adult supervision. Never fly in a place cluttered, always make sure the Cyber Surfer lifts off from an open area. A high impact crashing into obstacles may cause damage to the Cyber Surfer. Keep other peeps and yourself at least 1 meter away from the Cyber Surfer during the lift off. (Diagram A) Do Not play with Cyber Surfer near sand, rocky round or water. ever let the Cyber Surfer take off from any places apart from the ground. e.g. table, chair or cupboard etc. It may fall down and cause eee easily.
- Always keep an eye on the Cyber Surfer to avoid ing, crashing or landing on your head, our body or other people. It causes harm to people and may damage the Cyber Surfer. Never disassemble or modify the Cyber Surfer, it may damage the product and cause danger. Never place your hands or face near the propellers.
(Diagram B) Do not hold any parts beside the figure and the handles of Cyber Surfer. Beware do not halding the Caution outer frame as the propellers may hurt your hands. Diagram C) To avoid the outer frame beng hit by the propellers, hold the Cyber Surfer straight and level when the ower is switched on. ;
eware of any danger caused by potential sharp Points or sharp edges. ;
old the Cyber Surfer by grabbing the figure or the side handle to avoid any danger from propeller.
(Diagram D) Never operate the Cyber Surfer while sitting. Always operate the Cyber Surfer in a posture that allows you to quickly get out of the way if necessary. Do not release the Power Lever rapidly while landing as it may cause a hard crash on the floor and damage the Cyber Surfer. Always release the Power Lever SLIGHTLY for landing. Do not put foreign objects or tie material around the moving Joints such as the propellers, Do not catch the Cyber Surfer while it is flying.
(Diagram E') Never wave the antenna of the controller around or put it close to people face, as there is a risk that the antenna tip could poke someone's eye etc. be
- Do not touch tl
- Always switch off the Cyber Surfer and remove all
+ Make sure the Radio Controller is turned off when picking up the Cyber Surfer.
+ Keep your fingers away from the propellers while operaring the Cyber Surfer.
- Avoid touching any parts near the propellers after ing, as it a get hot after playing for a long time. e rotatory parts as it is relatively weak. batteries from the controller after each use. Never leave weak or dead batteries in the controller, as they may leak damaging chemicals. Charge the Cyber Surfer by using the provided adaptor only, DO NOT charge the Cyber Surfer with other AC/ DC adaptor. Remove all packaging material before the toy is given to a child. Transformers used with the toy are to be regularly examined for ree to the cord, plug, enclosure and other parts, and that, in the event of such damage, the toys must not be used with this transformer until the damage has been repaired. The toy is not intended for children under 3 years old. The toy must only be used with the recommended transformer. The transformer is not a toy. Toys liable to be cleaned with liquids are to be disconnected from the transformer before cleaning. www.aok-ltd.com eae: