EZ ConnectTM g 108Mbps WLAN Cardbus User Guide From SMCs EZ line of low-cost workgroup LAN solutions 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 April 2005 Revision #: R01, F1.0 Copyright Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright 2005 by SMC Networks, Inc. 38 Tesla Irvine, CA 92618 All rights reserved. Trademarks:
SMC is a registered trademark; and EZ Connect is a trademark of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders. Compliances Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which Increase the distance between the equipment and receiver. the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CSA Statement (Canada) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of Industry Canada. Le prsent appareil numrique nmet pas de bruits radio-lectriques dpassant les limites applicables aux appareils numriques de la classe B prescrites dans le Rglement sur le brouillage radiolectrique dict par lIndustrie. i Compliances CE Mark Declaration of Conformance for EMI and Safety (EEC) This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the compliance with these Directives, the following standards were applied:
RFI Emission:
Immunity:
Limit class B according to EN 55022:1998 Limit class B for harmonic current emission according to EN 61000-3-2/1995 Limitation of voltage fluctuation and flicker in low-voltage supply system according to EN 61000-3-3/1995 Product family standard according to EN 55024:1998 Electrostatic Discharge according to EN 61000-4-2:1995
(Contact Discharge: 4 kV, Air Discharge: 8 kV) Radio-frequency electromagnetic field according to EN 61000-4-3:1996 (80 - 1000 MHz with 1 kHz AM 80%
Modulation: 3 V/m) Electrical fast transient/burst according to EN 61000-4-4:1995
(AC/DC power supply: 1 kV, Data/Signal lines: 0.5 kV) Surge immunity test according to EN 61000-4-5:1995
(AC/DC Line to Line: 1 kV, AC/DC Line to Earth: 2 kV) Immunity to conducted disturbances, Induced by radio-frequency fields: EN 61000-4-6:1996 (0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3 V/m) Power frequency magnetic field immunity test according to EN 61000-4-8:1993 (1 A/m at frequency 50 Hz) Voltage dips, short interruptions and voltage variations immunity test according to EN 61000-4-11:1994
(>95% Reduction @10 ms, 30% Reduction @500 ms, >95%
Reduction @5000 ms) LVD:
EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997) ii Contents Compliances Federal Communication Commission Interference Statement CSA Statement (Canada) CE Mark Declaration of Conformance for EMI and Safety (EEC) Introduction Features Applications System Requirements Package Checklist Hardware Description LED Indicators Hardware Installation Driver and Utility Installation Utility Configuration Wireless Network Manager Configuration Link Information IP Information Site Survey Version Information Network Configuration and Planning Network Topologies Ad Hoc Wireless LAN Infrastructure Wireless LAN Setting the Communication Domain Troubleshooting Adapter Installation Problems Network Connection Problems Specifications General Specifications Data Rate and Transmission Power Typical Receiver Sensitivity Range i i i ii 1 1 2 2 2 3 3 4 5 9 9 10 13 15 16 17 18 18 18 19 20 21 21 21 23 23 25 25 iii Contents iv EZ CONNECT G 108MBPS WLAN CARDBUS Introduction The 108Mbps WLAN Cardbus is an IEEE 802.11g wireless network adapter that seamlessly integrates with existing Ethernet networks to support applications such as mobile users or temporary conferences. This solution offers a high data rate and reliable wireless connectivity with considerable cost savings over wired LANs (which include long-term maintenance overhead for cabling.) Just install enough wireless access points to cover your network area, plug wireless cards into your notebooks, and start networking. Using this card in conjunction with a wireless access point, you can create an instant network that integrates seamlessly with 10/100 Mbps Ethernet LANs. Moreover, moving or expanding your network is as easy as moving or installing additional access points no wires!
Features Wireless connection without the hassles and cost of cabling Greater flexibility to locate or move networked PCs Integrates with or replaces wired LANs at dramatically lower cost than wired alternatives Seamless connectivity to wired Ethernet LANs augments existing networks quickly and easily Easy installation Direct Sequence Spread-Spectrum (DSSS) technology provides robust, interference-resistant and secure wireless connection Complemetary Code Keying (CCK) ensures backward compatibility to the existing IEEE 802.11b WLAN infrastructure Orthogonal Frequency Division Multiplexing (OFDM) provides the speed required for todays high-bandwidth application Supports Windows 98SE/Me/2000/XP Supports WEP (Wired Equivalent Privacy) and WPA (Wi-Fi Protected Access) security Provides a user-friendly interface for configuration Extended range feature supported 1 EZ Connect g 108Mbps WLAN Cardbus Applications Offers a fast, reliable, cost-effective solution for wireless client access to the network in applications like these:
Remote access to corporate network information Email, file transfer, and terminal emulation Difficult-to-wire environments Historic or old buildings, asbestos installations, and open areas where wiring is difficult to employ Frequently changing environments Retailers, manufacturers, and banks who frequently rearrange the workplace and change location Temporary LANs for special projects or peak times Trade shows, exhibitions, and construction sites that need a temporary setup for a short time period. Retailers, airline, and shipping companies that need additional workstations for peak periods. Auditors who require workgroups at customer sites Access to database for mobile workers Doctors, nurses, retailers, office workers who need access to databases while being mobile in the hospital, retail store or office campus SOHO users SOHO (Small Office and Home Office) users who need easy and quick installation of a small computer network System Requirements Before you install the WLAN Cardbus, check your system for the following:
A laptop with a PCMCIA Type II or Type III slot Windows 98SE/Me/2000/XP (Prepare the Windows OS CD for use during installation) A minimum of 1500 Kbytes of free disk space for installing the driver and utility program 300 MHz processor or higher Other IEEE 802.11b/g-compliant devices installed in your area Package Checklist The WLAN Cardbus package includes:
One 108Mbps WLAN Cardbus 1 driver/utility installation program, and documentation CD Quick Installation Guide Please inform your dealer if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use them again to repack the product if there is a need to return it for repair. 2 Hardware Description The WLAN Cardbus supports 108Mbps connections to Ethernet networks. This card is fully compliant with specifications defined in IEEE 802.11b and IEEE 802.11g standards. It can be installed in any notebook with a Type II or TYPE III PCMCIA slot. It supports Windows 98SE/Me/2000/XP. LED Indicators The WLAN Cardbus includes two status LED indicators, as described in the following table. LED Link Activity Status On Flashing Flashing Description Indicates a valid connection with an access point. Indicates that the WLAN Cardbus is scanning for available networks. Indicates that the WLAN Cardbus is transmitting/receiving data. 3 Hardware Installation Warnings: Network cards are sensitive to static electricity. To protect the card, always touch the metal chassis of your notebook or the ground before handling the card. 1. Turn on your notebook. 2. Find an available Type II or Type III PCMCIA slot in your notebook. 3. With the PC Cards 68-pin connector facing the PCMCIA slot, label side up, slide the card completely into the slot as shown below. Note: The PCMCIA slot allows you to hot swap PC Cards any time. 4. Install the appropriate driver into your system. Drivers can be found on the driver CD that comes with the package. See the following section for instructions. 4 Driver and Utility Installation The CD labeled Driver and Utility CD that comes with the package contains the software drivers and utilities available for the WLAN Cardbus. Note: You may find that the instructions here do not exactly match your version of Windows. This is because these steps and screen shots were created from Windows XP. Windows 98SE, Windows Millennium Edition, and Windows 2000 are similar, but not identical, to Windows XP. 1. Place the installation CD into the CD-ROM drive. The program will auto-run. 2. Windows XP will automatically install the driver. 3. Insert the adapter into your computer when you see the following message. 5 EZ Connect g 108Mbps WLAN Cardbus 4. Once the utility has been installed into your system, the Found New Hardware Wizard window will appears. 5. Select Yes, this time only and click Next. 6. Choose the Install the software automatically option, and click Next. 6 7. Click Continue Anyway to proceed with the installation. Driver and Utility Installation Note: Do not select STOP Installation, as this will cancel the installation process, and the drivers will not be installed properly. 7 EZ Connect g 108Mbps WLAN Cardbus 8. Click Finish to exit the wizard. 9. When the wizard has finished installing the driver, the following screen will appear. Select Yes, I want to restart my computer now. Click Finish and your PC will restart. The driver and utility installation is completed. Your adapter is now ready for use. 8 Utility Configuration Wireless Network Manager Double-click the shortcut icon on the desktop, or from the task bar to launch the utility. You can also access the utility program from the Start menu. The configuration utility includes the following five tabs:
Configuration Allows you to monitor network status, configure wireless adapter parameters, and access security control. Link Information Shows wireless adapter statistics. IP Information Shows Network connection information. Site Survey Scans/Shows all the wireless devices in range. Version Information Shows software version information. At the bottom of the screen, there are three boxes that can be selected:
Wireless On/Off Click this button to turn on/turn off the radio signal of the adapter. Help Click this button to view the help file. Close Click this button to exit the utility. 9 EZ Connect g 108Mbps WLAN Cardbus Configuration This utility allows you to set the parameters for the wireless adapter. Select Profile To specify a profile for a specific configuration of parameters. New Click this button to create a new profile. Save Click this button to save a profile after configuring the settings. Delete Select the profile from the drop-down menu, and click this button to delete the profile. Auto Profile On/Off Click this button to turn on/off the Auto Profile feature. Active Profile The profile settings that you are using for the current connection. Common Tab Network Name (SSID) This is the Service Set ID (SSID) for the wireless network to which you want to connect. Network Type Set the station operation mode to ad hoc for network configurations that do not have an access point, or to Infrastructure for configurations with an access point. Transmit Rate Set the transmit rate you want from the pull-down menu. Click Apply Changes after you have made your selection. Lower settings may improve throughput in environments hostile to radio transmission. 10 Utility Configuration Power Save Enable or disable the power saving feature. Operating Mode The adapter supports 802.11b, 802.11g and 802.11g turbo mode. Check the type of network that you want to use for your wireless connection. Security Tab Go to the security tab to set the security features for your adapter. Click on this security button to turn on/turn off the security function. Turn on the security function, and set detail parameters for your adapter. To prevent unauthorized access, this adapter supports WEP (Wired Equivalent Privacy), and WPA (Wi-Fi Protected Access). WEP WEP (Wired Equivalent Privacy) implemented in the Wireless PC Card is based on the RC4 encryption algorithm. The security keys provided to ensure data confidentiality are four 10-bit keys for the 64-bit WEP setting and one 26-bit key for the 128-bit WEP setting. WEP security protects your wireless LAN against eavesdropping and unauthorized access by intruders. Security Type WEP (Wired Equivalent Privacy) is supported by the adapter to prevent unauthorized access. 11 EZ Connect g 108Mbps WLAN Cardbus Key Type Choose the Key Type (ASCII or Hex) from the drop-down list. ASCII: 13 regular text characters. Hex: 26 digits (0~9, A~F) hexadecimal characters. Authentication Mode Choose Open or Shared. Default Key Choose the Key Number that has the encryption string you prefer. If you are using a key generated from a passphrase, you must use the same passphrase and key on each station. Use Passphrase Check this box to auto-generate security keys for WEP encryption. Please note that you must use the same passphrase on all the stations in your network. WPA-PSK Encryption Type WPA (Wi-Fi Protected Access) is a stronger wireless security solution than WEP. It uses a combination of authentication and broadcast/session keys. Pre-Shared Key (PSK) If there is no authentication server on your SOHO network, you can issue the Pre-Shared Passphrase to the 108Mbps WLAN Cardbus. Please note that you must use the same passphrase on all the stations in your network. Key Type Choose the Key Type (ASCII or Hex) from the drop-down list. Notes: 1. Manual Pre-Shared Key supports up to 64-Hex characters. 2. Type 8 - 63 Hex characters for the Pre-Shared Passphrase. 12 Utility Configuration 3. Do not use a key that is long and complex for your clients to type accurately, as you might forget it. 4. A Hex (hexadecimal) digit is a number or letter in the range 0-9 or A-F. Link Information The Link Information screen displays the information on the current wireless network to which you are connected. Network Name This is the Service Set ID (SSID) for the wireless network to which you want to connect. Base Station Name ID The MAC address of the access point to which the card is connected in an infrastructure network. In an ad hoc network, this ID is a random number generated by the first station that communicates with other stations in the network. The BSS ID of the other stations will then be set to the same value. Channel This is the radio channel through which the access point communicates to stations within the same network. A Basic Service Set (BSS) consists of a group of wireless PCs and an access point that is directly connected to the wired LAN. To establish an ad hoc network, make sure the Channel is set to the same radio channel as that used by the other wireless clients in your group. However, if you are connecting to a network via an access point, the adapter will automatically use the same channel as that used by the access point. 13 EZ Connect g 108Mbps WLAN Cardbus Note: The available channel settings are limited by local regulations that determine the number of available channels. Current Connection Speed Shows the speed of the current wireless connection. Current Rx Rate This is the transmission rate of the current connection. Encryption This shows the encryption type of your wireless network. Operating Mode This adapter supports 802.11b and 802.11g mode. Status This is the station status. Country Shows the country where you are using the adapter. Throughput Shows the total number of data packets transmitted and received. Signal Strength Shows the relative strength of the wireless connection. Link Quality Shows the link quality of the wireless connection. 14 Utility Configuration IP Information This screen displays IP information for your laptop. Now that you have configured your adapter to connect to wireless networks, your laptop needs to obtain new network settings. To release the current network settings, click on Release, then click on Renew to obtain new IP settings. IP Address Client Internet address of the computer. IP Netmask Client A netmask is a set of four number blocks separated by periods. Each number is normally represented as the decimal equivalent of an eight-bit binary number, between 0 and 255. Every IP address consist of two parts
(the network address and the host number). The netmask is used to determine the size of these two parts. The positions of the bits that are set in the netmask are considered to represent the space reserved for the network address, while the bits that are cleared are considered to represent the space set aside for the host number. Gateway The IP address of the Gateway. Host Name Client The computers name on the network. 15 EZ Connect g 108Mbps WLAN Cardbus Site Survey The Site Survey screen displays available wireless networks. Choose one of them to connect to by double-clicking on an entry. Network Type Shows the network type. See "Configuration" on page 10. Network name Service Set ID (SSID) on the network. See "Configuration" on page 10. Mode Shows the wireless connection mode, whether its 802.11b or 802.11g. Secure This shows security mechnism has been enabled. A key icon indicates the encryption function is enabled. Signal This shows the signal strength of the listed wireless devices. Channel This is the channel used for the wireless connection. MAC address This is the MAC address of the listed wireless devices. 16 Version Information This screen shows information on the current version of the driver and configuration utility. Utility Configuration 17 Network Configuration and Planning This Wireless Solution supports a stand-alone wireless network configuration, as well as an integrated configuration with Ethernet LANs. The 108Mbps WLAN Cardbus can be configured as:
Ad hoc for departmental or SOHO LANs Infrastructure mode for networked LANs Network Topologies Ad Hoc Wireless LAN An ad hoc wireless LAN consists of a group of computers, each equipped with a wireless adapter, connected via radio signals as an independent wireless LAN. Computers in a specific ad hoc wireless LAN must be configured to the same radio channel. An ad hoc wireless LAN can be used for a branch office or SOHO operation. Ad Hoc Wireless LAN Notebook with Wireless USB Adapter Notebook with Wireless PC Card PC with Wireless PCI Adapter 18 Network Configuration and Planning Infrastructure Wireless LAN The 108Mbps WLAN Cardbus can also provide wireless workstations with access to a wired LAN. An integrated wired and wireless LAN is called an Infrastructure configuration. A Basic Service Set (BSS) consists of a group of wireless PC users, and an access point that is directly connected to the wired LAN. Each wireless PC in this BSS can talk to any computer in its wireless group via a radio link, or access other computers or network resources in the wired LAN infrastructure via the access point. The infrastructure configuration not only extends the accessibility of wireless PCs to the wired LAN, but also extends the effective wireless transmission range for wireless PCs by passing their signal through one or more access points. A wireless infrastructure can be used for access to a central database, or for connection between mobile workers, as shown in the following figure. Wired LAN Extension to Wireless Adapters File Server Desktop PC Switch Notebook with Wireless PC Card Adapter Access Point PC with Wireless PC I Adapter 19 EZ Connect g 108Mbps WLAN Cardbus Setting the Communication Domain Stationary Wireless PCs The Basic Service Set (BSS) is the communication domain for each access point. For wireless PCs that do not need to support roaming, set the domain identifier (SSID) for the wireless card to the SSID of the access point to which you want to connect. Check with your administrator for the SSID of the access point to which you should connect. Roaming Wireless PCs A wireless infrastructure can also support roaming for mobile workers. More than one access point can be configured to create an Extended Service Set (ESS). By placing the access points so that a continuous coverage area is created, wireless users within this ESS can roam freely. All wireless adapters and access points within a specific ESS must be configured with the same SSID and to the same radio channel. File Server Switch Notebook with Wireless PC Card Adapter Access Point
<BSS2>
Desktop PC Wireless Cell Coverage Area PC with Wireless PCI Adapter
<BSS1>
Access Point Notebooks with Wireless PC Card Adapters PC with Wireless PC I Adapter
<ESS>
Seamless Roaming 20 Troubleshooting Check the following troubleshooting items before contacting technical support. Adapter Installation Problems If your computer cannot find the Wireless PC Card or the network driver does not install correctly, check the following:
Make sure the adapter is securely seated in the PCMCIA slot. Check for any hardware problems, such as physical damage to the cards connector. Try the card in another PCMCIA slot. If this also fails, test your computer with another wireless card that is known to operate correctly. Make sure your computer is using the latest BIOS. If there are other network adapters in the computer, they may be causing conflict. Remove the other network adapters from the computer and test the wireless adapter separately. Check for a defective computer or PCMCIA connection by trying the adapter in another computer that is known to operate correctly. If it still does not work, take out the wireless adapter. Then go to Control Panel and delete the adapter from your network configuration menu. Restart your PC and reinstall the card. Network Connection Problems If the Link LED on the PC Card does not light, or if you cannot access any network resources from the computer, check the following:
Make sure the correct software driver is installed for your operating system. If necessary, try reinstalling the driver. Make sure the computer and other network devices are receiving power. The access point you want to attach to may be defective. Try using another access point. If you cannot access a Windows or NetWare service on the network, check that you have enabled and configured the service correctly. If you cannot connect to a particular server, be sure that you have access rights and a valid ID and password. If you cannot access the Internet, be sure you have configured your system for TCP/IP. 21 EZ Connect g 108Mbps WLAN Cardbus If your wireless station cannot communicate with a computer in the Ethernet LAN when configured for Infrastructure mode, check the following:
Make sure the access point that the station is associated with is powered on. If you still cannot connect, change the access point and all the stations within the BSS to another radio channel. Make sure the SSID is the same as that used by the access point for a station with roaming disabled, or the same as that used by the access points in the extended service set (ESS). 22 Specifications General Specifications Functional Criteria Network Connection Operating Range IEEE 802.11g - Wireless Outdoor: Up to 400 m (1312 ft) at 54 Mbps Indoor: Up to 180 m (590 ft) at 54 Mbps Radio Signal Signal Type Operating Frequency Operating Channels Sensitivity Modulation Output Power Direct Sequence Spread-Spectrum (DSSS) USA (FCC) and Canada (IC): 2.412 ~ 2.462 GHz Europe (ETSI): 2.412 ~ 2.472 GHz Spain: 2.457 ~ 2.462 GHz France: 2.457 ~ 2.472 GHz Japan (STD-T66/STD-33): 2.412 ~ 2.484 GHz USA (FCC) and Canada (IC): 11 channels Europe (ETSI): 13 channels Spain: 2 channels France: 4 channels Japan (STD-T66/STD-33): 14 channels
-68 dBm (typical) CCK, OFDM
+9 dBm (minimum) Physical Characteristics Power Consumption Dimensions Antenna LED Indicator Host Interface 3.3 V, stand by mode: 0.24, sleep mode: 0.04. transmit mode: 0.36, receive mode: 0.23 Type II PC Card + antenna 12.8 x 5.3 cm (5.04 x 2.09 in.) Built-in dual antenna Link, Activity PCMCIA, Type II Standards Conformance Wireless Standard IEEE 802.11b, IEEE 802.11g 23 EZ Connect g 108Mbps WLAN Cardbus Environmental Temperature Humidity Vibration/Shock/Drop Certification CE Mark Emissions Software Drivers Drivers Operating: 0 to 50 C (32 to 131 F) Storage: -20 to 75 C (-4 to 167 F) 5 to 90% (non-condensing) IEC 68-2-34, IEC 68-2-27, IEC68-2-32 EN 50081-1, EN 55022 Class B EN 50082-1, EN 61000-4-2 FCC Part 15(B), ETS 300-328, VCCI Windows 98SE (Second Edition) Windows Me Windows 2000 Windows XP 24 Data Rate and Transmission Power Standard 802.11b 802.11g Data Rate 1 Mbps 2 Mbps 5.5 Mbps 11 Mbps 6 Mbps 9 Mbps 12 Mbps 18 Mbps 24 Mbps 36 Mbps 48 Mbps 54 Mbps Transmission Power (dBm) 17 17 17 17 16 16 16 16 15 15 13 13 Typical Receiver Sensitivity Range Note: Frame (1000 Bytes PDUS) Packet Error Rate < 10%
Standard Data Rate 802.11b 802.11g 1 Mbps 2 Mbps 5.5 Mbps 11 Mbps 6 Mbps 9 Mbps 12 Mbps 18 Mbps 24 Mbps 36 Mbps 48 Mbps 54 Mbps Modulation Rate Receiver Sensitivity (dBm)
-90
-88
-85
-82
-88
-87
-84
-82
-79
-75
-68
-68 Specifications 25 EZ Connect g 108Mbps WLAN Cardbus 26 FOR TECHNICAL SUPPORT, CALL:
From U.S.A. and Canada (24 hours a day, 7 days a week)
(800) SMC-4-YOU; Phn: (949) 679-8000; Fax: (949) 679-1481 From Europe : Contact details can be found on www.smc-europe.com or www.smc.com INTERNET E-mail addresses:
techsupport@smc.com european.techsupport@smc-europe.com Driver updates:
http://www.smc.com/index.cfm?action=tech_support_drivers_downloads World Wide Web:
http://www.smc.com http://www.smc-europe.com FOR LITERATURE OR ADVERTISING RESPONSE, CALL:
U.S.A. and Canada:
Spain:
UK:
France:
Italy:
Benelux:
Central Europe:
Nordic:
Eastern Europe:
Sub Saharian Africa:
North West Africa:
CIS:
PRC:
Taiwan:
Asia Pacific:
Korea:
Japan:
Australia:
India:
(800) SMC-4-YOU;
34-91-352-00-40;
44 (0) 1932 866553;
33 (0) 41 38 32 32;
39 (0) 335 5708602;
31 33 455 72 88;
49 (0) 89 92861-0;
46 (0) 868 70700;
34 -93-477-4920;
216-712-36616;
34 93 477 4920;
7 (095) 7893573;
86-10-6235-4958;
886-2-8797-8006;
(65) 238 6556;
82-2-553-0860;
81-45-224-2332 ;
61-2-8875-7887;
91-22-8204437 ;
Fax (949) 679-1481 Fax 34-93-477-3774 Fax 44 (0) 118 974 8701 Fax 33 (0) 41 38 01 58 Fax 39 02 739 14 17 Fax 31 33 455 73 30 Fax 49 (0) 89 92861-230 Fax 46 (0) 887 62 62 Fax 34 93 477 3774 Fax 216-71751415 Fax 34 93 477 3774 Fax 7 (095) 789 35 73 Fax 86-10-6235-4962 Fax 886-2-8797-6288 Fax (65) 238 6466 Fax 82-2-553-7202 Fax 81-45-224-2331 Fax 61-2-8875-7777 Fax 91-22-8204443 If you are looking for further contact information, please visit www.smc.com, www.smc-europe.com, or www.smc-asia.com. 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 Model Number: SMCWCBT-G Revision Number E042005-R01 F 1.0