AMR170 Series NFC Reader User Manual Document History Description Original Release - Firmware version 1.0.7 Revised Oct 2013 Firmware version 2.1.2 Revised Jan 2014 Firmware version 2.13 Revised Apr 2014 Firmware version 2.15 Revised Jan 2016 Include FCC statement Model AMR171,AMR175 AMR171,AMR175 AMR171,AMR175 AMR171,AMR175 AMR171,AMR175 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 1.1AMR170 Series NFC Reader Overview The AMR170 Series NFC Reader is a new generation NFC card reader. The AMR170 Series NFC reader can read a wide range of contactless smart card covering single size UID card to double size UID card. Card ID data can be output via industry standard Wiegand or Asis Proprietary RS485. Both models are available to cater for various modes of security and operation needs. Model AMR171 AMR175 LCD n/a yes Keypad n/a yes LED yes yes Buzzer yes yes Table 1 Model Components 1.2 Reader Wiring and Color Code Figure 1 and 2 illustrates the Connection between the Smartcard reader and the host controller. A recommended color code is shown in Table 2. Terminal Point Label Dev+
Dev-
+V GND D0 D1 ERL OKL BUZ Description RS485+
RS485-
+12VDC DC Ground Wiegand Data 0 Wiegand Data 1 Red LED Green LED Buzzer Hold Recommended Cable Color Blue Grey Red Black Green White Brown Orange Yellow Purple Table 2 Wiring and Cable Color code 1.3 DIP Switch Setting AMR171/175 series reader has 8 way DIP switch with function as show in below table. Function in Wiegand Card format setting Card format setting Card format setting Card format setting Bit Label Function in RS485 A0 A1 A2 A3 Address bit 0 Address bit 1 Address bit 2 Address bit 3 Mode RS485/ Wiegand OFF Wiegand, ON RS485 8/4 Byte CSN/CAN OFF 8 byte, ON 4 byte OFF CSN, ON CAN TST OFF Run, ON - Testing Table 3 Dip Switch function explain 1 2 3 4 5 6 7 8 Note: Bit 7 CAN refer to Card Application Number found on Ez-Link card. Hex Address Bit Label 80 81 82 83 84 85 86 87 Bit7 Bit 8 Bit6 Refers to Table 3 for other DIP Switch Setting. Bit 2 A1 0 0 1 1 0 0 1 1 Bit 1 A0 0 1 0 1 0 1 0 1 Table 4 RS485 Readers Address Dip Switch Setting Bit4 A3 0 0 0 0 0 0 0 0 Bit3 A2 0 0 0 0 1 1 1 1 Bit5 1 1 1 1 1 1 1 1 DIPSW Bit Format 26bit 32bit 32bit(8bit) 34bit 37bit 37(8digit) 40bit 40bit(8digit) 56bit 64bit 80bit 168bit(ASIS) DIP1 Wiegand setting DIP2 DIP3 DIP4 off on off on off on off on off on off on off off on on off off on on off off on on off off off off on on on on off off off on off off off off off off off off on on on on DIP5 OFF Wiegand Wiegand
=Off DIP6 off =
64bit RS485 on=
32bit RS485 DIP7 off =
CSN RS485 on =
CAN RS485 DIP8 off =
Run on=
test Table 5 Wiegand bit format Dip Switch setting Note : Since the Contactless SmartCard CSN is 32 bit can be up to 10 digits decimal when converted. This is the solution to truncate the CSN and provide a result that once converted, it only give maximum of 8-digit decimal. The 37 bit odd and even priority bit is a result of getting the first and second half of total bit length. 1.4 Installation and Mounting Instruction Identify the reader mounting location. The reader may install onto any surface, including metal. Remove the snap on cover and use the reader as a template, draw the mounting hole position onto the mounting surface. Drill 2 appropriate holes to install the reader. Drill a 25mm hole for the cable. Connect the external (site) cable to the terminal block on the reader according to the wiring code below. Double-check the wiring connection. Replace the snap on cover and tighten it with the screw provided. Switch on the power to test the reader and observe. Figure 1 Physical Dimension To remove the readers cover, unscrew the screw in the bottom and flip open the cover. Figure 2 Removal of Cover Figure 3 Mounting Method 1.5 Operation Guide The AMR170 series reader must work with the ACU controller (it cannot operate by itself). The reader allows user to access by Card only, Details of operation please refer to IBSS and/or ACU manual. Figure 4 Presenting Cards to Reader Keeping the card in parallel to the AMR17x reader a maximum read range can be obtained. The Reader will still be able to read Card when the card is presented at an angle but this will result in the reducing of read range. Card and PIN operation (Model 175) a) When the Green Led is blinking after presenting card, the means that PIN is request. Key in PIN and follows by # key b) Key in PIN + 1 for PIN DURESS (Example PIN is 1234, for duress activation, key pin 1235) Note that the maximum PIN is up to 6 digit. When the reader is powered-up, the LED and the Buzzer will respond. Description a) Upon Power Up the Reader **N is setting on the DIP switch. Buzzer response
(AMR171/175) The buzzer will beep
(N+1) time accord to the DIP switch setting LED Response
(AMR171/175) Readers Amber LEDs Blink (N+1) times LCD Display (For AMR175 only) Model No Reader Address Version b) Reader Ready Silent Red LED always ON Green LED Short blink at every 3 secs interval DD/MM/YY / 00:00:00 Ready c) Reader Alarm & Event Message on LCD Display (AMR175 only) Access Grant Buzzer Beep once Green LED Blink once Access Denied Buzzer Beep once Red LED Blink once Access Invalid Buzzer Beep once Red LED Blink once Door Open Too Long Buzzer Beeping Red LED Blinking Door Force Open Buzzer Beeping Red LED Blinking Free Access Silent Green LED ON Door Locked Silent Red LED ON Fire Activated Buzzer Beeping Red LED Blinking Box Tamper Buzzer beeping Red LED Blinking Pin Mode Buzzer beeping Green LED Blinking Pre-Alarm Buzzer beeping Red LED Blinking Radio Frequency Interference Devices generate RF noise that may interfere with the reception of the signal from the access card. This will result in the reduction of read range. Examples of devices are radios, televisions, and cellular phones. The read range is affected by the amount of interference (noise) in the area. The reader should mount more than 1.5m away from the any devices that emits RF that may interfere with the signal received from the access control cards. 1.6 Package List - AMR171/175 Reader Item Description Qty. Complete with snap on cover 1 Mounting cover screw, M3 1 Installation and this document. GrantedDeniedInvalidDOTLDoor ForceunlockedLockedFire AlarmBox-TamperEnter PINPre-Alarm 1.7 Product Electrical Specification Power Supply (Recommend) Regulated linear power supply, +12VDC, 300mA Operating Voltage Range
+9VDC - + 24VDC Operating Current at +12VDC 85mA (average) 185mA (peak) Maximum Cable Distance 150meters (500feet)
(base on Belden 9538 24AWG 0.6mm, 8 core cable foilshield) (for wiegand interface)
(base on Belden 9534 24AWG 06.mm, 4 core cable foilshield) (for RS485 interface) Read Range
<=50mm (2)
( Read Range is dependent on local installation conditions ) Transmit Frequency 13.56MHz LED LCD Display Buzzer Tri Color Red, Green, Amber 96 x 64 Graphic LCD (AMR175) Multi-tone Operating temperature Range
-20oC to 50oC ( -22oF to 150oF) Colour Material Weight Dimension Black ABS 350 grams 95mm (Height) X 60mm (Width) X 16mm (Thickness) Wire Termination 10 conducting wire at length approx. 300mm Reader Mode Card Only, Card and PIN. PIN Input Keypad 1 6 Digits (AMR175) 3 x 4 Keys (AMR175) Communication Interface RS485 or Wiegand ( Selectable ) Wiegand interface Output bit format 26, 32, 37, 40, 56, 80, 168(Asis) bits format and 8-digit 32, 37, 40 bits format Support Card Type Mifare ( ISO 14443-A, ISO 14443-B) EZ-Link Mounting Output CAN or CSN (Selectable) Hook On Bracket