by:
ASUSTeK COMPUTER INC.
latest update:
2026-09-15
model:
BE211D2
Nineteen grants have been issued under this FCC ID from 02/09/2026 to 09/15/2026 (this is one of two hundred and thirty-five releases in 2026 for this grantee). Public details available include internal & external photos, manuals, and frequency information. some products also feature user submitted or linked password defaults, troubleshooting guides, instructions, drivers, & warrantee terms.
ASUSTeK COMPUTER INC. To: Federal Communications Commission Date: 6/29/2026 7435 Oakland Mills Road Columbia, MD 21046 USA Attestation Certification designating a U.S. Agent for Service of Process Section 2.911(d)(7)
(KDB 986446 D01 Covered Equipment) Grantee Code: MSQ ASUSTeK COMPUTER INC. (the applicant) as required by section 2.911(d)(7), designate below contact located in the United States for purposes of acting as the applicants agent for service of process. The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Sincerely yours, Applicant/Grantee US Agent
(Signature) FRN: 0005821988
(Signature) FRN: 0033432428 Company Name: ASUSTeK COMPUTER INC. Company Name: ASUS COMPUTER INTERNATIONAL Contact: Jackson Yen / Associate Vice President Contact: Gigi Liu / CEO Tel: +886-2-28943447 Email: [email protected] Tel: (510) 399-9138 Email: [email protected] Address: 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan Address: 48720 Kato Road, Fremont, CA 94538, United States
Class II Permissive Change Letter Date: 2026/8/5 FCC ID: MSQBE211D2 Original Grant Date: 06/18/2026 (DXX, DSS, DTS, NII, 6CD, 6VL) Pursuant to CFR 2.1043, (ASUSTeK COMPUTER INC.) hereby requests a Class II Permissive Change. Modification:
-Change #1:
The device has done C2PC establishes portable category SAR conditions for the ASUS model CX9406CAA, CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H, the grant date is described above. In this application, the host device enables the TAS (Time average SAR) function and applies the C2PC. The WLAN TAS feature is enabled on 2.4GHz and 5GHz band; and Wi-Fi 6E band does not support TAS function. The WLAN TAS feature is enabled. The exact same WLAN authorized modules are reused in this Notebook PC with the exact same TAS algorithm validation methods for time averaging SAR as approved in KDB 968002.
-Change #2:
The software security information is kept the same as the module's original application. Thank you for your attention to this matter. Sincerely,
Jackson Yen / Associate Vice President ASUSTeK COMPUTER INC.
Covered List Attestation Letter Date: August 25, 2026 FCC ID: MSQBE211D2 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA To Whom It May Concern:
Attestation Sections 2.911(d)(5) of the FCC Rules
(KDB 986446 D01 Covered Equipment) Section 2.911(d)(5)(i) ASUSTeK COMPUTER INC. (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. ASUSTeK COMPUTER INC. (the applicant) further certifies that no cybersecurity or anti-
virus software from Kaspersky Lab, Inc. (or its successors/assignees), including integrated Kaspersky software, is installed in the equipment being certified, pursuant to DA-24-886 and KDB 986446 D01 Guidance B(2a). Section 2.911(d)(5)(ii) ASUSTeK COMPUTER INC. (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as defined in 1.50002 of the Commissions rules, as an entity that produces covered communications equipment or services, nor as a subsidiary or affiliate of such an entity. If you have any questions, please feel free to contact me. Sincerely,
Jackson Yen / Associate Vice President ASUSTeK COMPUTER INC.
ASUSTeK COMPUTER INC. Request for Confidentiality Date: 6/2/2026 Subject: Confidentiality Request for: FCC ID: MSQBE211D2 / IC: 3568A-BE211D2 Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 12.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent *1 Permanent Permanent Permanent Permanent Permanent *3 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual ASUSTeK COMPUTER INC. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:
The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality for FCC Applications:
The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Short Term Confidentiality for Industry Canada Applications:
Starting May 2022, ISED will recognize short term confidentiality on certain exhibits until the intended date of marketing. The applicant requests the exhibits selected above as short term confidential be withheld from public view until: of 180 days after approval. Sincerely, By:
(Signature/Title2) Jackson Yen / Associate Vice President
(Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:
https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 041521-14
ASUSTeK COMPUTER INC. Authority to Act as Agent Date: July 7, 2025 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern:
Eurofins E&E Wireless Taiwan Co., Ltd./William Chung is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: 12/31/2027 By:
(Signature1) _____ Jackson Yen_____
(Print name) Title:
Associate Vice President On behalf of: ASUSTeK COMPUTER INC.
(Company Name) Telephone:
+886-2-28943447 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 050222-17
NII - Unlicensed National Information Infrastructure TX
Class II Permissive Change
2
6665 ~ 6665
6CD - 15E 6 GHz Low Power Dual Client
3
2422 ~ 2462
DTS - Digital Transmission System
4
2404 ~ 2478
DXX - Part 15 Low Power Communication Device Transmitter
5
2402 ~ 2480
DSS - Part 15 Spread Spectrum Transmitter
6
6105 ~ 6905
6VL - 15E 6 GHZ Very Low Power Device
7
2026-06-18
6105 ~ 6905
6VL - 15E 6 GHZ Very Low Power Device
Class II permissive change or modification of presently authorized equipment
8
5855 ~ 5855
NII - Unlicensed National Information Infrastructure TX
9
2402 ~ 2480
DSS - Part 15 Spread Spectrum Transmitter
10
2422 ~ 2462
DTS - Digital Transmission System
11
6665 ~ 6665
6CD - 15E 6 GHz Low Power Dual Client
12
2404 ~ 2478
DXX - Part 15 Low Power Communication Device Transmitter
13
2026-02-09
2422 ~ 2462
DTS - Digital Transmission System
Change in identification of presently authorized equipment. Original FCC ID: PD9BE211D2 Grant Date: 08/27/2025
14
6665 ~ 6665
6CD - 15E 6 GHz Low Power Dual Client
15
6105 ~ 6905
6VL - 15E 6 GHZ Very Low Power Device
16
5855 ~ 5855
NII - Unlicensed National Information Infrastructure TX
17
JBP - Part 15 Class B Computing Device Peripheral
18
2402 ~ 2480
DSS - Part 15 Spread Spectrum Transmitter
19
2404 ~ 2478
DXX - Part 15 Low Power Communication Device Transmitter
Change in identification of presently authorized equipment. Original FCC ID: PD9BE211D2 Grant Date: 09/15/2025
Application Forms
app
s
Applicant Information
various
Effective
2026-09-15
various
2026-06-18
various
2026-02-09
various
Applicant's complete, legal business name
ASUSTeK COMPUTER INC.
various
FCC Registration Number (FRN)
0005821988
various
Physical Address
1F, No. 15, Lide Rd.
various
Beitou, Taipei, N/A
various
Beitou, Taipei, N/A 112
various
Taiwan
app
s
TCB Information
various
TCB Application Email Address
h******@acbcert.com
various
TCB Scope
A4: UNII devices & low power transmitters using spread spectrum techniques
various
A2: Low Power Transmitters (except Spread Spectrum) and radar detectors operating above 1 GHz
various
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
app
s
FCC ID
various
Grantee Code
MSQ
various
Equipment Product Code
BE211D2
app
s
Person at the applicant's address to receive grant or for contact
various
Name
J**** Y******
various
Title
Associate Vice President
various
Telephone Number
+886-********
various
Fax Number
+886-********
various
E-mail
j******@asus.com
app
s
Technical Contact
various
Firm Name
Eurofins E&E Wireless Taiwan Co., Ltd.
various
DEKRA Testing and Certification Co., Ltd
various
DEKRA Testing and Certification Co., Ltd.
various
Name
F****** L******
various
L******** Y******
various
Physical Address
No. 140-1, Changan Street, Bade District
various
No. 26, Huaya 1st Rd., Guishan Dist.
various
Huaya 1st Rd., Guishan Dist.
various
Taoyuan City
various
New Taipei City
various
Taiwan
various
Telephone Number
886-3********
various
886-3********
various
886 3********
various
E-mail
f******@cpt.eurofinsasia.com
various
l******@dekra.com
app
s
Non Technical Contact
various
Firm Name
ASUS COMPUTER INTERNATIONAL
various
Name
G**** L********
various
Physical Address
48720 Kato Road
various
Fremont, 94538
various
Fremont
various
Fremont, California
various
United States
various
Taiwan
various
Telephone Number
51060********
various
51060********
various
(510)********
various
Fax Number
(510)********
various
E-mail
g******@asus.com
app
s
Confidentiality (long or short term)
various
Does this application include a request for confidentiality for any portion(s) of the data
contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?:
Yes
various
No
various
Long-Term Confidentiality
Does this application include a request for confidentiality for any portion(s) of the data
contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?:
Yes
various
No
various
If so, specify the short-term confidentiality release date (MM/DD/YYYY format)
03/14/2027
various
12/15/2026
if no date is supplied, the release date will be set to 45 calendar days past the date of grant.
app
s
Cognitive Radio & Software Defined Radio, Class, etc
various
Is this application for software defined/cognitive radio authorization?
No
various
Equipment Class
NII - Unlicensed National Information Infrastructure TX
various
6CD - 15E 6 GHz Low Power Dual Client
various
DTS - Digital Transmission System
various
DXX - Part 15 Low Power Communication Device Transmitter
various
DSS - Part 15 Spread Spectrum Transmitter
various
6VL - 15E 6 GHZ Very Low Power Device
various
JBP - Part 15 Class B Computing Device Peripheral
various
Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant)
Intel BE211
various
Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application?
Yes
various
No
various
Modular Equipment Type
Single Modular Approval
various
Purpose / Application is for
Class II Permissive Change
various
Class II permissive change or modification of presently authorized equipment
various
Change in identification of presently authorized equipment. Original FCC ID: PD9BE211D2 Grant Date: 08/27/2025
various
Change in identification of presently authorized equipment. Original FCC ID: PD9BE211D2 Grant Date: 09/15/2025
various
Composite Equipment: Is the equipment in this application a composite device subject to an
additional equipment authorization?
Yes
various
Related Equipment: Is the equipment in this application part of a system
that operates with, or is marketed with, another device that requires an equipment authorization?
No
various
Grant Comments
Modular Approval. Power Output listed is conducted for UNII-1 to UNII-3 and EIRP for UNII-4 bands. UNII-4 band is for indoor operation only. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. This module is approved in mobile/portable configurations. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. Grantee must coordinate with OEM integrator to determine applicable host configurations to ensure RF exposure compliance, including simultaneous transmission SAR requirements according to published KDB 616217 supplement documentation. When all conditions of this filing cannot be met installation of this device into specific final products may require the submission of a permissive change application, containing appropriate data demonstrating compliance, or a new application. This transmitter has 20MHz, 40MHz, 80MHz, 160 MHz bandwidth modes as described in this filing. Device is a client only device containing a 2 x 2 MIMO configuration, enabled for either 2.4 or 5 GHz band operations as described in this filing. OEM/Host integrator must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance. OEM/Host integrator is responsible for complying with the instructions and requirements for each transmitter they choose to integrate into a host product.
This module is approved in portable configurations with PIFA reference antenna (5.11 to 5.15 dBi) at 42mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.
This module meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (5.11 to 5.15 dBi), Dipole reference antenna (4.03 to 5.15 dBi) and Monopole reference antenna (4.43 to 4.95 dBi).
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 1.16 W/kg and 1.55 W/kg respectively.
2.4GHz and 5GHz WLAN TAS feature enabled.
various
Power Output listed is EIRP. The first five rows above are for LPI mode and the remaining rows are for Standard mode. Modular Approval filing. Device is a 2 x 2 MIMO configuration, enabled for 6 GHz operations as described in this filing. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.
This device supports 20, 40, 80, 160, and 320 MHz BW modes.
This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi) at 42mm minimum test separation distance. Power Density and SAR testing was performed to demonstrate RF exposure compliance.
This module meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 1.16 W/kg and 1.55 W/kg respectively.
2.4GHz and 5GHz WLAN TAS feature enabled.
various
Power Output listed is conducted. Modular Approval. Power output has been reduced at the upper band-edge channels as shown in filings under this FCC ID. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. This module is approved in mobile/portable configurations. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. Grantee must coordinate with OEM integrator to determine applicable host configurations to ensure RF exposure compliance, including simultaneous transmission SAR requirements according to published KDB 616217 Supplement documentation. When all conditions of this filing cannot be met installation of this device into specific final products may require the submission of a permissive change application, containing appropriate data demonstrating compliance, or a new application. OEM/Host integrator must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance. Device is a client only device containing a 2 x 2 MIMO configuration, enabled for either 2.4 or 5 GHz band operations as described in this filing. OEM/Host integrator is responsible for complying with the instructions and requirements for each transmitter they choose to integrate into a host product.
This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 42mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.
This module meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 1.13 W/kg and 1.55 W/kg respectively.
2.4GHz and 5GHz WLAN TAS feature enabled.
various
Modular Approval filing. This grant covers BT-HADM mode of operation. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.
SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi).
This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (2.95 dBi).
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 0.39 W/kg and 1.55 W/kg respectively.
2.4GHz and 5GHz WLAN TAS feature enabled.
various
Power Output listed is conducted. Modular Approval filing. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.
This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 42mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.
This module meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 0.39 W/kg and 1.55 W/kg respectively.
2.4GHz and 5GHz WLAN TAS feature enabled.
various
Power Output listed is EIRP. Modular Approval Filing. This grant covers VLP mode and is not allowed to operate under the control of a Low-power indoor access point while in this mode of operation. Device is a 2x2 MIMO configuration, enabled for 6 GHz operations as described in this filing. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating
conditions for satisfying RF exposure compliance.
The host-product antenna must be permanently installed and not replaceable by the end user. Any attempt to replace or modify the antenna by the end user is strictly prohibited and will void the FCC certification.
This device supports 20, 40, 80,160, and 320 MHz BW modes.
This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi) at 42mm minimum test separation distance. Power Density and SAR testing was performed to demonstrate RF exposure compliance.
This module meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 1.16 W/kg and 1.55 W/kg respectively.
2.4GHz and 5GHz WLAN TAS feature enabled.
various
Power Output listed is EIRP. Modular Approval Filing. This grant covers VLP mode and is not allowed to operate under the control of a Low-power indoor access point while in this mode of operation. Device is a 2x2 MIMO configuration, enabled for 6 GHz operations as described in this filing. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating
conditions for satisfying RF exposure compliance.
The host-product antenna must be permanently installed and not replaceable by the end user. Any attempt to replace or modify the antenna by the end user is strictly prohibited and will void the FCC certification.
This device supports 20, 40, 80,160, and 320 MHz BW modes.
This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi) at 42mm minimum test separation distance. Power Density and SAR testing was performed to demonstrate RF exposure compliance.
This module meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 1.16 W/kg and 1.55 W/kg respectively.
various
Modular Approval. Power Output listed is conducted for UNII-1 to UNII-3 and EIRP for UNII-4 bands. UNII-4 band is for indoor operation only. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. This module is approved in mobile/portable configurations. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. Grantee must coordinate with OEM integrator to determine applicable host configurations to ensure RF exposure compliance, including simultaneous transmission SAR requirements according to published KDB 616217 supplement documentation. When all conditions of this filing cannot be met installation of this device into specific final products may require the submission of a permissive change application, containing appropriate data demonstrating compliance, or a new application. This transmitter has 20MHz, 40MHz, 80MHz, 160 MHz bandwidth modes as described in this filing. Device is a client only device containing a 2 x 2 MIMO configuration, enabled for either 2.4 or 5 GHz band operations as described in this filing. OEM/Host integrator must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance. OEM/Host integrator is responsible for complying with the instructions and requirements for each transmitter they choose to integrate into a host product.
This module is approved in portable configurations with PIFA reference antenna (5.11 to 5.15 dBi) at 42mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.
This module meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (5.11 to 5.15 dBi), Dipole reference antenna (4.03 to 5.15 dBi) and Monopole reference antenna (4.43 to 4.95 dBi).
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 1.16 W/kg and 1.55 W/kg respectively.
various
Power Output listed is conducted. Modular Approval filing. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.
This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 42mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.
This module meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 0.39 W/kg and 1.55 W/kg respectively.
various
Power Output listed is conducted. Modular Approval. Power output has been reduced at the upper band-edge channels as shown in filings under this FCC ID. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. This module is approved in mobile/portable configurations. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. Grantee must coordinate with OEM integrator to determine applicable host configurations to ensure RF exposure compliance, including simultaneous transmission SAR requirements according to published KDB 616217 Supplement documentation. When all conditions of this filing cannot be met installation of this device into specific final products may require the submission of a permissive change application, containing appropriate data demonstrating compliance, or a new application. OEM/Host integrator must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance. Device is a client only device containing a 2 x 2 MIMO configuration, enabled for either 2.4 or 5 GHz band operations as described in this filing. OEM/Host integrator is responsible for complying with the instructions and requirements for each transmitter they choose to integrate into a host product.
This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 42mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.
This module meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 1.13 W/kg and 1.55 W/kg respectively.
various
Power Output listed is EIRP. The first five rows above are for LPI mode and the remaining rows are for Standard mode. Modular Approval filing. Device is a 2 x 2 MIMO configuration, enabled for 6 GHz operations as described in this filing. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.
This device supports 20, 40, 80, 160, and 320 MHz BW modes.
This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi) at 42mm minimum test separation distance. Power Density and SAR testing was performed to demonstrate RF exposure compliance.
This module meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 1.16 W/kg and 1.55 W/kg respectively.
various
Modular Approval filing. This grant covers BT-HADM mode of operation. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.
SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi).
This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (2.95 dBi).
Class II Permissive Change with a decrease in the Output Power through firmware respectively and to request approval for portable category specific host Googlebook, Notebook PC, Model: CX9406CAA and CB9406CAA with the antenna LUXSHARE-ICT, part no. LA9RF655-NB-H (14008-06670100). The detail information please refer to the filing.
Antenna(s) is/are of the same type and lower gain from original approval. SAR testing was performed to demonstrate RF compliance.
The highest reported Body and Simultaneous SAR values are 0.39 W/kg and 1.55 W/kg respectively.
various
This C2PC adds portable for full power and 3 different additional SKU versions of the product that are electronically identical but have different power profiles.
Power Output listed is conducted. Modular Approval. Power output has been reduced at the upper bandedge channels as shown in filings under this FCC ID. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. This module is approved in mobile/portable configurations. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. Grantee must coordinate with OEM integrator to determine applicable host configurations to ensure RF exposure compliance, including simultaneous transmission SAR requirements according to published KDB 616217 Supplement documentation. When all conditions of this filing cannot be met installation of this device into specific final products may require the submission of a permissive change application, containing appropriate data demonstrating compliance, or a new application. OEM/Host integrator must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance. Device is a client only device containing a 2 x 2 MIMO configuration, enabled for either 2.4 or 5 GHz band operations as described in this filing. OEM/Host integrator is responsible for complying with the instructions and requirements for each transmitter they choose to integrate into a host product.
SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi).
For 42mm SKU: The highest reported Body and Simultaneous SAR values are 0.46 W/kg and 1.56 W/kg respectively.
The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.
SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.79 W/kg and 1.60 W/kg respectively.
SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.60 W/kg respectively.
SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.79 W/kg and 1.54 W/kg respectively.
This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).
various
This C2PC adds portable for full power and 3 different additional SKU versions of the product that are electronically identical but have different power profiles.
Power Output listed is EIRP. The first five rows above are for LPI mode and the remaining rows are for Standard mode. Modular Approval filing. Device is a 2 x 2 MIMO configuration, enabled for 6 GHz operations as described in this filing. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance. This device supports 20, 40, 80,160, and 320 MHz BW modes.
Power Density and SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi).
For 42mm SKU: The highest reported Body and Simultaneous SAR values are 0.71 W/kg and 1.56 W/kg respectively.
The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.
SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.60 W/kg respectively.
SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.60 W/kg respectively.
SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.79 W/kg and 1.54 W/kg respectively.
This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference This filing meets MPE requirements of KDB 447498 an antenna(s): PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.
various
This C2PC adds portable for full power and 3 different additional SKU versions of the product that are electronically identical but have different power profiles.
Power Output listed is EIRP. Modular Approval Filing. This grant covers VLP mode and is not allowed to operate under the control of a Low-power indoor access point while in this mode of operation. Device is a 2x2 MIMO configuration, enabled for 6 GHz operations as described in this filing. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.
The host-product antenna must be permanently installed and not replaceable by the end user. Any attempt to replace or modify the antenna by the end user is strictly prohibited and will void the FCC certification.
This device supports 20, 40, 80,160, and 320 MHz BW modes.
Power Density and SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi).
For 42mm SKU: The highest reported Body and Simultaneous SAR values are 0.71 W/kg and 1.56 W/kg respectively.
The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.
SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.60 W/kg respectively.
SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.60 W/kg respectively.
SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.79 W/kg and 1.54 W/kg respectively.
This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.
various
This C2PC adds portable for full power and 3 different additional SKU versions of the product that are electronically identical but have different power profiles.
Modular Approval. Power Output listed is conducted for UNII-1 to UNII-3 and EIRP for UNII-4 bands. UNII-4 band is for indoor operation only. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. This module is approved in mobile/portable configurations. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. Grantee must coordinate with OEM integrator to determine applicable host configurations to ensure RF exposure compliance, including simultaneous transmission SAR requirements according to published KDB 616217 supplement documentation. When all conditions of this filing cannot be met installation of this device into specific final products may require the submission of a permissive change application, containing appropriate data demonstrating compliance, or a new application. This transmitter has 20MHz, 40MHz, 80MHz, 160 MHz bandwidth modes as described in this filing. Device is a client only device containing a 2 x 2 MIMO configuration, enabled for either 2.4 or 5 GHz band operations as described in this filing. OEM/Host integrator must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance. OEM/Host integrator is responsible for complying with the instructions and requirements for each transmitter they choose to integrate into a host product.
SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (5.11 to 5.15 dBi).
For 42mm SKU: The highest reported Body and Simultaneous SAR values are 0.80 W/kg and 1.56 W/kg respectively.
The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.
SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.60 W/kg respectively.
SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.60 W/kg respectively.
SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.75 W/kg and 1.54 W/kg respectively.
This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (5.11 to 5.15 dBi), Dipole reference antenna (4.03 to 5.15 dBi) and Monopole reference antenna (4.43 to 4.95 dBi).
various
This C2PC adds portable for full power and 3 different additional SKU versions of the product that are electronically identical but have different power profiles.
Power Output listed is conducted. Modular Approval filing. This device contains a 2 x 2 MIMO configuration. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.
SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi).
For 42mm SKU: The highest reported Body and Simultaneous SAR values are 0.05 W/kg and 1.56 W/kg respectively.
The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.
SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.79 W/kg and 1.60 W/kg respectively.
SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.78 W/kg and 1.60 W/kg respectively.
SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.28 W/kg and 1.54 W/kg respectively.
This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).
various
This C2PC adds portable for full power and 3 different additional SKU versions of the product that are electronically identical but have different power profiles.
Modular Approval filing. This grant covers BT-HADM mode of operation. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.
SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi).
For 42mm SKU: The highest reported Body and Simultaneous SAR values are 0.05 W/kg and 1.56 W/kg respectively.
The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.
SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.79 W/kg and 1.60 W/kg respectively.
SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.78 W/kg and 1.60 W/kg respectively.
SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.28 W/kg and 1.54 W/kg respectively.
This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (2.95 dBi).
various
Is there an equipment authorization waiver associated with this application?
No
various
If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded?
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details