BaiCells CN6671 CPE User Manual V1.0 All rights reserved BaiCells Technologies Co., Ltd. About This Document This document is a user guide for CN6671 CPE. Copyright Notice BaiCells copyrights this specification. No part of this specification may be reproduced in any form or means, without the prior written consent of BaiCells. Disclaimer This specification is preliminary and is subject to change at any time without notice. BaiCells assumes no responsibility for any errors contained herein. For more information, please consult our technical engineers. Revision Record Date Version Description 30 Jun, 2016 V1.0 Initial released. Contact Us BaiCells Technologies Co., Ltd.North America Address: 555 Republic Drive, Suite 200 Plano, TX 75074 E-mail: support_na@baicells.com Phone: +1-972-800-1157 Website: http://www.baicells.com/
1 Contents 1. Hardware Specification .................................................................................................... 2 1.1 Appearance ............................................................................................................... 2 1.2 Specifications ............................................................................................................ 5 1.2.1 Basic Description ............................................................................................... 5 1.2.2 RF Specifications ............................................................................................... 5 1.2.3 Environment Specifications .............................................................................. 6 2. Operation Steps .............................................................................................................. 7 3. Configuration Guide ....................................................................................................... 8 3.1 Log In .......................................................................................................................... 8 3.2 Network Settings ........................................................................................................ 9 3.3 WiFi Settings ............................................................................................................. 12 3.4 Security Settings ....................................................................................................... 13 3.5 VPN Settings ............................................................................................................. 14 3.6 VoIP Settings ............................................................................................................ 15 3.7 System Settings ........................................................................................................ 16 4. Trouble Shooting .......................................................................................................... 17 4.1 Device cannot Access to CPE through WiFi .............................................................. 17 4.2 CPE cannot connect to internet ............................................................................... 17 5. Regulatory Compliance ................................................................................................ 19 Appendix A Shipping List ................................................................................................ 21 Contents of Figure Figure 1-1 Front View of CN6671 .................................................................................... 2 Figure 1-2 Back View of CN6671 ................................................................................. 3 Figure 1-3 Side View of CN6671 .................................................................................. 4 Figure 3-1 CPE Web Client Login Page ....................................................................... 8 Figure 3-2 Home Page of Web Client .......................................................................... 9 Figure 3-3 LET Settings.............................................................................................. 10 Figure 3-4 LET Status ................................................................................................ 10 Figure 3-5 APN Management ..................................................................................... 11 Figure 3-6 LAN Settings ............................................................................................. 12 Figure 3-7 WLAN Settings .......................................................................................... 13 Figure 3-8 Security Settings ....................................................................................... 14 Figure 3-9 VPN Settings ............................................................................................. 15 Figure 3-10 VoIP Settings .......................................................................................... 15 Figure 3-11 System Settings ...................................................................................... 16 Contents of Table Table 1-1 LED Indicators of Front View ........................................................................ 2 Table 1-2 LED Indicators of Back View ........................................................................ 4 Table 1-3 Interfaces and Buttons of Back View ........................................................... 4 Table 1-4 Interfaces and Buttons of Side View ............................................................ 4 1. Hardware Specification 1.1 Appearance The front view of CN6671 is shown in Figure 1-1. Figure 1-1 Front View of CN6671 Index Dimension Weight Color Description 167(H)*187(W)*44(T)mm 310g White The LED indicators of front view are described in Table 1-1. Table 1-1 LED Indicators of Front View LTE Name Description Color LED Behavior Status Indicator PWR WLAN Power Indicator WLAN Indicator blue OFF No Power Supply Steady On Power On blue OFF WLAN function disable Blanking Data transmission through WLAN Steady On WLAN function enable WPS WiFi blue OFF WPS disable Protected Setup Blanking WiFi terminal being accessing Steady On WPS Enable 2 Tel1 ~ Tel2 Voice blue OFF Not establish a connection with telephone interface indicator the voice server Blanking(1/sec) Registering with the voice server Blanking(2/sec) Connection has been established Steady On Be connected with voice server MODE Mode blue OFF No access in LTE network Indication Blanking LTE scan, connecting LTE Signal 4 LTEs, blue All OFF No Connected Steady On In LTE network Indicate connection state and signal strength One by one Displays the current wireless signal bar network signal strength, the display, four stronger the signal, the more bars bars on In addition, two special status indicators (Firmware upgrading and reset process) is described as follows:
Status Indicator Status Description Firmware upgrade WPS + WLAN two lights flash simultaneously Reset process Except 5 signal strength indicator, the other indicator are all on The back view of CN6671 is shown in Figure 1-2. Figure 1-2 Back View of CN6671 3 The LED indicators of back view are described in Table 1-2. Table 1-2 LED Indicators of Back View LTE Name Description Color LED Behavior Status Indicator LAN1 ~
Eth Indication Green OFF Ethernet connection is not LAN4 established Steady On Ethernet connection is normal Blanking Ethernet interface data being transmitted The interfaces and buttons of back view are described in Table 1-3. Table 1-3 Interfaces and Buttons of Back View Name ETH RJ45 POTS-RJ11 Description 4 LAN Ports 2 RJ11 interface, phone / fax / POS, providing VoIP functions under conditions of software support Power Power port is the linked power adapter which is parceled. Power Switch Power Switch The side view of CN6671 is shown in Figure 1-3. Figure 1-3 Side View of CN6671 The interfaces and buttons of side view are described in Table 1-4. Table 1-4 Interfaces and Buttons of Side View Name Description Restore Button Long press over 10s to restore the factory settings WPS WiFi WiFi Protected Setup Turn on or off WiFi Function USIM Slot Support 1.8V/3.0V USIM 4 1.2 Specifications 1.2.1 Basic Description Specification Description LTE Standard 3GPP Release 9 Comment None Ethernet LAN 4 RJ-45 port 10/100 auto-sensing, LAN * 4 Port USIM auto-MDX Support 1.8V/3.3V 2FF USIM Tel Port 2 FXS RJ11 Ports None None LED Indicators POWER / WLAN / WPS / TEL / MODE /
None Signal Strength / LAN Indicator * 4 Power Switch Switch Reset/Restore Tact Button Button WPS WiFi Protected Setup None Long press over 10s to restore the factory settings None Power Supply Input: Universal range 100V~240V AC, None 50Hz Output: 12V DC 1A 1.2.2 RF Specifications No. Feature Capability Comments LTE Mode Value TDD LTE Channel Bandwidth 5/10/15/20 Max Output Power Transmit Power Dynamic Range 17 63 LTE Standard 3GPP R9 Frequency 3650 ~ 3700 Antenna Gain 5 WiFi Frequency 2400 ~ 2483.5 WiFi Channel BW 20/40 1 2 3 4 5 6 7 8 9 Unit MHz dBm dB MHz dBi MHz MHz 25 B43 10 11 WiFi Antenna Type WiFi Antenna Gain 2*2 2 MIMO Built-in antenna dBi 5 1.2.3 Environment Specifications No. Feature Capability 1 2 3 Operating Temperature Storage Temperature Operating Humidity Value
-10 ~ 45
-20 ~ 60 0 ~ 95 Unit
%
6 2. Operation Steps Attention:
Make sure the CPE is turned off before you insert or remove the SIM card. Otherwise, the CPE and SIM card may be damaged. 1. Insert SIM card into USIM slot. Note:
If you want to remove the SIM card, please tightly press the SIM card, the SIM card will pop up. 2. Insert power adaptor and turn on it. The power indicator getting steady on indicate that the power supply is normal. Otherwise, you need to check whether the power adaptor is normal. 3. Wait for 1 minute, if MODE and SIGNAL STRENGTH indicators flash simultaneously, it indicates that SIM card did not connect or is invalid. You need to buy new SIM card or contact vendor. 4. MODE indicator flashing indicates that the device is searching and registering to LTE network. If the device connect to LTE network normally, MODE indicator is steady on. SIGNAL STRENGHTH indicator indicate the strength of LTE signal. If the device cannot connect to LTE network, MODE indicator flash ceaselessly. 5. WLAN indicator indicates whether WiFi function is enabled. If WiFi is enabled, mobile phone and laptop can connect to network by WiFi. SSID is Airtouch-8783. For the first time, no WiFi password is required. 6. PC and laptop can connect to internet through LAN port. 7 3. Configuration Guide 3.1 Log In 1. In the browsers address column, type in http://192.168.1.1, click Enter to open web client login page, as shown in Figure 3-1 Figure 3-1 CPE Web Client Login Page 2. Input user name admin, password admin, and click Login. The homepage of web client is given in Figure 3-2. The home page displays basic information of CPE. 8 Figure 3-2 Home Page of Web Client 3.2 Network Settings 1. In the left navigation bar, choose Network>LTE Settings, as shown in Figure 3-3 and Figure 3-4. In Network, you can complete LTE and LAN settings. 9 Figure 3-3 LET Settings Figure 3-4 LET Status In general, LTE Settings leaves the default setting. In Module Information area, if IMSI field is empty, you need to check whether SIM card has inserted or damaged. Settings area displays the connection type and connection status, the value of Status is unconnected, connecting, and connected. Connect Method choose Auto mode. 10 Status displays the current connection status:
UL Frequency /DL Frequency: Frequency point of cell which connect or search. If the field is empty, it indicate that searching LTE network is failed. RSRP0/RSRP1: Indicate the RSRP of current channel. If the value is greater than -110dBm, it indicates that the LTE signal is within the service scope of base station, if the value is greater than -95dBm, it indicates LTE signal well. SINR: Indicate the SINR of current channel, if the value is greater than 25dB, it indicates channel quality well. Cell ID: Indicate cell ID of connection. 2. In the left navigation bar, choose Network>APN Management, as shown in Figure 3-5. In general, the APN Management leaves the default value. Figure 3-5 APN Management 3. In the left navigation bar, choose Network>LAN Settings, as shown in Figure 3-6. 11 Figure 3-6 LAN Settings In LAN Host Settings area, note that IP address of LAN port and Subnet Mask avoid conflict with the local gateway. In DHCP Settings area, distribute dynamic IP address for local WiFi and LAN host. The IP address segment is the same segment with LAN Host Settings. 3.3 WiFi Settings In the left navigation bar, choose WiFi. WiFi settings includes WLAN general settings, WPS settings, SSID profile, WLAN encryption type, password setting, access management and WDS settings, as shown in Figure 3-7. 12 Figure 3-7 WLAN Settings 3.4 Security Settings In the left navigation bar, choose Security. Security settings includes general router security functions, such as MAC/IP/URL filter, port forwarding, access restrictions, and so on, as shown in Figure 3-8. 13 Figure 3-8 Security Settings 3.5 VPN Settings In the left navigation bar, choose VPN. VPN settings supports PPTP, as shown in Figure 3-9. 14 Figure 3-9 VPN Settings 3.6 VoIP Settings In the left navigation bar, choose VoIP. VoIP settings includes SIP server settings and user account settings, as shown in Figure 3-10. Figure 3-10 VoIP Settings 15 3.7 System Settings In the left navigation bar, choose System. System settings includes maintenance, version management, diagnostic service, and so on, as shown in Figure 3-11. Figure 3-11 System Settings 16 4. Trouble Shooting 4.1 Device cannot Access to CPE through WiFi 1. Check whether WiFi function is enabled. Observe WLAN indicator is steady on or flashing. If WLAN indicator is OFF, you need to enter into WiFi Settings to enable WiFi function. Refer to 3.3WiFi Settings. 2. SSID and password is incorrect. In web client, enter into WiFi Settings, reset SSID and password. 3. If web client cannot login, you need to reset CPE. Long press reset button over 10s to restore the factory settings. 4.2 CPE cannot connect to internet Without SIM card or SIM card damaged 1. Check whether SIM card have inserted into USIM slot. 2. Log in web client, check whether there is the hint PIN LOCKED. If PIN LOCKED, you need to unlock SIM card as follows. a) Enter into PIN Management, try to type in: 1234. b) If 1234 is incorrect, try three times, enter into PIN code input page, type in:
12345678. c) Reset PIN code and set PIN Verification is Disable. d) If PIN code is incorrect, you need to contact SIM card vendor. 3. Log in web client, choose LTE Settings, check the value of IMSI. If it is empty and SIM card is normal, you need to reboot CPE, wait for 1minute, log in web client again, check the value of IMSI. If it is also empty, change SIM card. Without LTE signal or LTE network access privilege 1. Check the status of CPE indicator. If MODE indicator is flashing continuous, it indicates that CPE is searching network, wait for 5 minutes. 2. If CPE still cannot connect to internet. Log in web client, enter into LTE Settings, if IMSI is invalid (did not consist with user agreement), you need to change SIM card or contact SIM card vendor. 17 3. Lon in web client, choose Network>LTE Settings. If the value of Connect Method is Manual, reset it to Auto, and reboot CPE. 4. If CPE still cannot connect to internet. Lon in web client, choose Network>LTE Settings. Check whether the value of status is Unconnected in Settings area, it indicates that LTE network is abnormal, you need to contact vendor. If the value of status is Connecting for a long time, it indicates that CPE is not within scope of LTE network, you need to move CPE to next to a window. 5. If CPE still cannot connect to internet, it indicates that CPE is not in service network, you need to contact vendor. 18 5. Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. 19 IC Compliance This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. 20 Appendix A Shipping List Item Assembled product 12V/1A adapter User Manual Quantity 1 1 1 21