FCC ID: K7SF5D7630-4A ADSL Modem with Built-in Wireless Router

ADSL Modem with Built-In 802.11g Wireless Router Network your computers with this one-box solution that connects and shares your ADSL Internet access User Manual F5D7630-4A F5D7630-4B TABLE OF CONTENTS Introduction . 1 Overview . 1 Key Features . 1 Package Contents . 3 System Requirements . 3 Knowing your Router . 4 Placement of your Router . 7 Connecting and Configuring your Router . 8 Navigating the Web Browser Interface . 14 Understanding the Web-Based User Interface . 17 Manually Configuring Network Settings . 48 Glossary . 55 Troubleshooting . 61 Information . 63 INTRODUCTION Thank you for purchasing the ADSL Modem with Built-In 802.11g Wireless Router

(the Router). In minutes, you will be able to share your Internet connection and network your computers. The following is a list of features that make your new Router an ideal solution for your home or small office network. OVERVIEW Key Features Integrated 802.11g Wireless Access Point 802.11g is an exciting new wireless technology that provides up to 54Mbps

(nearly five times faster than 802.11b) data rates. Works with Both PCs and Mac Computers The Wireless ADSL Modem Router supports a variety of networking environments including Mac OS 8.x, 9.x, X v10.x, AppleTalk, Linux, Windows 95, 98, Me, NT, 2000, and XP, and others. All that is needed is an Internet browser and a network adapter that supports TCP/IP (the standard language of the Internet). Front-Panel LED Display Lighted LEDs on the front of the Router indicate which functions are in operation. Youll know at-a-glance whether your Router is connected to the Internet. This feature eliminates the need for advanced software and status-

monitoring procedures. Web-Based User Interface You can set up the Routers functions easily through your web browser, without having to install additional software onto the computer. There are no disks to install or keep track of and, best of all, you can make changes and perform setup functions from any computer on the network quickly and easily. NAT IP Address Sharing Your Router employs Network Address Translation (NAT) to share the single IP address assigned to you by your Internet Service Provider while saving the cost of adding additional IP addresses to your Internet service account. 1 INTRODUCTION SPI Firewall Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including IP Spoofing, Land Attack, Ping of Death (PoD), Denial of Service (DoS), IP with zero length, Smurf Attack, TCP Null Scan, SYN flood, UDP flooding, Tear Drop Attack, ICMP defect, RIP defect, and fragment flooding. Integrated 10/100 4-Port Switch The Router has a built-in, four-port network switch to allow your wired computers to share printers, data and MP3 files, digital photos, and much more. The switch features automatic detection so it will adjust to the speed of connected devices. The switch will transfer data between computers and the Internet simultaneously without interrupting or consuming resources. Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes for the easiest possible connection of a network. The DHCP server will assign IP addresses to each computer automatically so there is no need for a complicated networking setup. MAC Address Filtering For added security, you can set up a list of MAC addresses (unique client identifiers) that are allowed access to your network. Every computer has its own MAC address. Simply enter these MAC addresses into a list using the web-based user interface and you can control access to your network. Applications and Advantages Economically connect multiple computers to a single Internet connection SOHO (Small Office/Home Office) networking needs Provides the easy and quick small network installation SOHO users need 2 INTRODUCTION Package Contents ADSL Modem with Built-In 802.11g Wireless Router RJ45 Ethernet Networking Cable (for connecting the Router to the computer) RJ11 Phone Line Cord (for connecting the Router to the ADSL line) ADSL In-Line Filter Power Supply Quick Installation Guide User Manual CD-ROM Registration Card System Requirements ADSL connection At least one computer with an installed network interface adapter TCP/IP networking protocol installed on each computer CAT5 networking cable (or better) Microsoft Internet Explorer 4.0 or later, or Netscape 4.0 or later 3 KNOWING YOUR ROUTER Front Panel Power LED

(PWR) ADSL SYN Status LED ADSL Data LED Wireless Network LED LAN Port Status LEDs Power LED (PWR) OFF Green Router is OFF Router is ready ADSL SYN Status LED OFF Solid Green Blinking Green This LED lights in GREEN to indicate that your Modem Router is connected properly to the ADSL line. No ADSL connection ADSL connection is ready Negotiating connection ADSL Data LED OFF Green Blinking No WAN connection WAN connection is ready Indicates WAN activity Wireless Network LED OFF Green Blinking Wireless network is OFF Wireless network is ready Indicates wireless activity 4 KNOWING YOUR ROUTER No device is linked to the port 10/100Base-Tx device connected LAN Port-Status LEDs OFF Solid Orange Blinking Orange Port activity These LEDs are labeled 14 and correspond to the numbered ports on the rear of the Router. When a computer is properly connected to one of the LAN ports on the rear of the Router, the LED will light. When information is being sent over the port, the LED blinks rapidly. Rear Panel Antennas LAN Ports Reset Button Power Jack ADSL Port LAN Ports The LAN ports are RJ45, 10/100 auto-negotiation. The ports are labeled 1 through 4. These ports correspond to the numbered LEDs on the front of the Router. Connect your LAN computers or any networking devices to one of these ports. Reset Button The Reset button is used in rare cases when the Router may function improperly. Resetting the Router will restore the Routers normal operation while 5 KNOWING YOUR ROUTER maintaining the programmed settings. You can also restore the factory default settings by using the Reset button. Use the restore option in instances where you may have forgotten your custom password. a. Resetting the Router Push and release the Reset button. When the Power/Ready light becomes solid again, the reset is complete. b. Restoring the Factory Defaults Press and hold the Reset button for 10 seconds then release it. When the Power/Ready light becomes solid again, the restore is complete. Power Jack Connect the included 12V DC power supply to this inlet. Using the wrong type of power adapter may cause damage to your Router. ADSL Port This port is for connection to your ADSL line. Connect your ADSL line to this port. 6 PLACEMENT OF YOUR ROUTER Proper placement of your Router is important to ensure the best performance of your wireless network. Typically, indoors your Wireless Router can provide a circular coverage area of 250 feet or more. However, different types of construction materials and other obstructions in a building can greatly affect the wireless signal and decrease the range. Whenever possible, your Router should be placed as close as possible to the center of the area that you want to cover. In multi-story homes, place the Router on a floor that is as close to the center of the home as possible; this may mean placing the Router on an upper floor. Use care when choosing the location of your Router. Be aware of appliances or large objects such as a refrigerator or washer/dryer unit that may be on the opposite side of a wall from where you decide to place your Router. Place the Router on top of a desk and away from metal cabinets and computer cases. Do not place objects or components on top of the Router. Make sure that both antennas are pointing UP at all times. Metallic-based UV window tint can affect wireless performance. Do not place the Router next to a tinted window. We realize that in the real world, it may not be possible to place your Router in the center of your coverage area. In cases where you may experience difficulty covering the entire area you want, try placing the Router as high as possible. Wireless devices work best in a line-of-sight situation where there are no obstacles between the wireless computer and the Router. The Router may also be mounted to a wall with the antennas facing UP. There are other options for expanding your wireless coverage area. Visit www. belkin.com/networking for solutions. The wireless signal can be affected by many things including neighboring wireless networks, microwave ovens in operation, and 2.4GHz cordless phones. While these things can affect the network performance, your wireless network typically will work fine under most conditions where these devices exist. 7 CONNECTING AND CONFIGURING YOUR ROUTER ISP Settings Please collect the following information from your ISP before setting up the Wireless ADSL Modem Router. For PPPoE and PPPoA users VCI and VPI number An ISP account user name and password For fixed IP users IP address and subnet mask IP address for your ISPs Gateway Server and Domain Name Server Connect the System Connect the ADSL Line Run standard telephone cable from the wall jack providing ADSL service to the ADSL port on your Wireless ADSL Modem Router. When inserting an ADSL RJ11 plug, be sure the tab on the plug clicks into position to ensure that it is properly seated. If you are using splitterless ADSL service, add low-pass filters between the ADSL wall jack and your telephones. (These filters pass voice signals through but filter data signals out.) Phone Line Configuration Installing a Full-Rate Connection If you are using a full-rate (G.dmt) connection, your service provider will attach the ADSL line to a data/voice splitter. In this case, you can connect your phones and computer directly to the splitter as shown on the next page. 8 CONNECTING AND CONFIGURING YOUR ROUTER Installing with a Splitter Installing a Splitterless Connection If you are using a splitterless (G.lite) connection, then your service provider will attach the outside ADSL line directly to your phone system. In this case, you can connect your phones and computer directly to the incoming ADSL line, but you will have to add low-pass filters to your phones as shown on the next page. 9 CONNECTING AND CONFIGURING YOUR ROUTER Installing without a Splitter Attach to your Network Using Ethernet Cabling The four LAN ports on the ADSL Modem Router auto-negotiate the connection speed to 10Mbps Ethernet or 100Mbps Fast Ethernet, as well as the transmission mode to half duplex or full duplex. Configuring the Router The Belkin Wireless ADSL Modem Router is equipped with a Web-Based Interface that you can use to set up the Router. From the Web-Based Interface, you can perform the following tasks:

View the Routers current settings and status. Configure the Router to connect to your ISP with the settings that they provided you. Change the current network settings such as the internal IP address, the IP address pool, DHCP settings, and more. 10 CONNECTING AND CONFIGURING YOUR ROUTER Set the Routers firewall to work with specific applications (port forwarding). Set up security features such as client restrictions and MAC address filtering. Enable the DMZ feature for a single computer on your network. Change the Routers internal password. Reset the Router. Reset the Routers default settings. Update the Routers firmware. Step 1: Installing the Hardware 1. Power down your equipment. 2. Connect each PC to one of the ports on the rear of the Router labeled LAN by using a RJ45 networking cable. LAN Ports 3. Connect the telephone cable from the wall jack providing ADSL service to the ADSL port on your Router. Note: When inserting an ADSL RJ11 plug, be sure the tab on the plug clicks into position to ensure that it is properly seated. 4. Connect the power adapter to the Router. 5. After the Router is turned on, the Routers Power light should be on. 11 CONNECTING AND CONFIGURING YOUR ROUTER 6. Turn on the rest of your computers. After your computers boot up, a LAN link light (on the front of the Router) will be on for each port to which a wired computer is connected. These lights are your means to verify that your computers are connected. LAN Port Status LEDs Step 2: Set your Computers Network Settings to Work with a DHCP Server Configure the TCP/IP settings on your computers to obtain an IP address automatically. The Router will assign each computer an IP address in the range of 192.168.2.x. In most cases, your computer is programmed to automatically obtain your IP address when you turn it on. If your computer is not set to work with a DHCP server, then see the section in this manual called Manually Configuring Network Settings for directions. Step 3: Configuring the Router Using the Web-Based User Interface Using your Internet browser, you can access the Routers Web-Based User Interface. In your browser, type 192.168.2.1 (do not type in anything else such as http:// or www). Then press the Enter key. 12 CONNECTING AND CONFIGURING YOUR ROUTER Logging into the Router To configure the Routers settings, you have to log in. The Router is supplied with no password entered. In the login screen, leave the password blank and click the Submit button to log in. Logging out of the Router One computer at a time can log into the Router for the purposes of making changes to the settings of the Router. Once a user has logged in to make changes, there are two ways that the computer can be logged out. Clicking the Logout button will log the computer out. The second method is automatic. The login will time-out after a specified period of time. The default login time-out is 10 minutes. This can be changed from 1 to 99 minutes. For more information, see the section in this manual titled Changing the Login Time-out Setting. 13 NAVIGATING THE WEB BROWSER INTERFACE Setup Wizard 1. Internet Sharing Select the connection type you are using. This information is provided by your ISP. 2. Setting your ISP Connection Type to PPPoE or PPPoA Enter the PPPoE (Point-to-Point Protocol over Ethernet) or PPPoA information in the provided spaces, and click Next. Click Apply to activate your settings. This information is provided by your ISP. User Name - Enter the ISP assigned user name. (Assigned by your ISP). Password - Enter your password. (Assigned by your ISP). Retype Password - Confirm the password. (Assigned by your ISP). VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier

(VCI) parameter here. (Assigned by your ISP). 14 NAVIGATING THE WEB BROWSER INTERFACE 3. Setting your Connection Type to Disable Internet Sharing Enter VPI/VCI value in the provided spaces, and then click Next. Click Apply to activate your settings. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier

(VCI) parameter here. (Assigned by your ISP). 4. Setting your Connection Type to Multiple Protocol over ATM Mode Enter ATM (Asynchronous Transfer Mode) information in the provided spaces, and click Next. Click Apply to activate your settings. WAN IP - Enter an IP address for the Wireless ADSL Modem Router WAN interface.

(Assigned by your ISP). Subnet Mask - Enter a subnet mask. (Assigned by your ISP). 15 NAVIGATING THE WEB BROWSER INTERFACE VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier

(VCI) parameter here. (Assigned by your ISP). Default Gateway - Enter a default gateway IP address. If the Wireless ADSL Modem Router cannot find the destination address within its local network, it will forward the packets to the Default Gateway. (Assigned by your ISP). 5. Click apply to activate your settings. You have finished installing your new Belkin Router. You should have Internet access at this point. To test your Internet connection, open your browser and visit a website such as www.belkin.com. 16 UNDERSTANDING THE WEB-BASED USER INTERFACE The home page shows you a quick view of the Routers status and settings. All advanced setup pages can be reached from this page. 1 10 2 5 4 3 9 8 7 6 1. Quick-Navigation Links You can go directly to any of the Routers UI pages by clicking directly on these links. The links are divided into logical categories and grouped by tabs to make finding a particular setting easier to find. Clicking on the header of each tab will show you a short description of the tabs function. 2. Home Button 3. The Home button is available in every page of the UI. Pressing this button will take you back to the home page. Internet Status Indicator This indicator is visible in all pages of the Router, indicating the connection status of the Router. When the indicator says connection OK in GREEN, the Router is connected to the Internet. When the Router is not connected to the Internet, the indicator will read no connection in RED. The indicator is automatically updated when you make changes to the settings of the Router. 4. Login/Logout Button This button enables you to log in and out of the Router with the press of one button. When you are logged into the Router, this button will change to read Logout. Logging into the Router will take you to a separate login 17 UNDERSTANDING THE WEB-BASED USER INTERFACE page where you will need to enter a password. When you are logged into the Router, you can make changes to the settings. When you are finished making changes, you can log out of the Router by clicking the Logout button. For more information about logging into the Router, see the section called Logging into the Router. 5. Help Button The Help button gives you access to the Routers help pages. Help is also available on many pages by clicking more info next to certain sections of each page. 6. LAN Settings Shows you the settings of the Local Area Network (LAN) side of the Router. Changes can be made to the settings by clicking the LAN Quick Navigation link on the left side of the screen. 7. Features 8. Shows the status of the Routers NAT, firewall, and wireless features. Changes can be made to the settings by clicking on any one of the links or by clicking the Quick Navigation links on the left side of the screen. Internet Settings Shows the settings of the Internet/WAN side of the Router that connects to the Internet. Changes to any of these settings can be made by clicking on the Internet/WAN Quick Navigation link on the left side of the screen. 9. Version Info Shows the firmware version, boot-code version, hardware version, and serial number of the Router. 10. Page Name The page you are on can be identified by this name. This manual will sometimes refer to pages by name. For instance, LAN > LAN Settings refers to the LAN Settings page. 18 UNDERSTANDING THE WEB-BASED USER INTERFACE Changing LAN Settings All settings for the internal LAN setup of the Router can be viewed and changed here. 1. LAN Settings Clicking on the header of the LAN tab (A) will take you to the LAN tabs header page. A quick description of the functions can be found here. To view the settings or make changes to any of the LAN settings, click on LAN Settings (B) or to view the list of connected computers, click on DHCP client list (C). A B C 1 2 3 4 5 6 19 UNDERSTANDING THE WEB-BASED USER INTERFACE 1. IP Address The IP address is the internal IP address of the Router. The default IP address is 192.168.2.1. To access the setup interface, type this IP address into the address bar of your browser. This address can be changed if needed. To change the IP address, type in the new IP address and click Apply Changes. The IP address you choose should be a non-routable IP. Examples of a non-routable IP are:

192.168.x.x (where x is anything between 0 and 255) 10.x.x.x (where x is anything between 0 and 255) 2. Subnet Mask There is no need to change the subnet mask. This is a unique, advanced feature of your Belkin Router. 3. DHCP Server The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically. The default setting is On. The DHCP server can be turned OFF if necessary, however, in order to do so you must manually set a static IP address for each computer on your network. To turn off the DHCP server, select Off and click Apply Changes. 4. IP Pool The IP Pool is the range of IP addresses set aside for dynamic assignment to the computers on your network. The default is 2100 (99 computers). If you want to change this number, you can do so by entering a new starting and ending IP address and clicking on Apply Changes. The DHCP server can assign 100 IP addresses automatically. This means that you cannot specify an IP address pool larger than 100 computers. For example, starting at 50 means you have to end at 150 or lower so as not to exceed the 100-client limit. The starting IP address must be lower in number than the ending IP address. 5. Lease Time Lease time is the length of time the DHCP server will reserve the IP address for each computer. We recommend that you leave the lease time set to Forever. The default setting is Forever, meaning that any time a computer is assigned an IP address by the DHCP server, the IP address will not change for that particular computer. Setting lease times for shorter intervals, such as 20 UNDERSTANDING THE WEB-BASED USER INTERFACE one day or one hour, frees IP addresses after the specified period of time. This also means that a particular computers IP address may change over time. If you have set any of the other advanced features of the Router, such as DMZ or client IP filters, these are dependent on the IP address. For this reason, you will not want the IP address to change. 6. Local Domain Name The default setting is Belkin. You can set a local domain name (network name) for your network. There is no need to change this setting unless you have a specific advanced need to do so. You can name the network anything you want such as MY NETWORK. DHCP Client List You can view a list of the computers (known as clients), which are connected to your network. You are able to view the IP address (1) of the computer, the host name (2) (if the computer has been assigned one), and the MAC address (3) of the computers network interface card (NIC). Pressing the Refresh (4) button will update the list. If there have been any changes, the list will be updated. 1 2 3 4 21 UNDERSTANDING THE WEB-BASED USER INTERFACE 2. Internet WAN The Internet WAN tab is where you will set up your Router to connect to your Internet Service Provider. The Router is capable of connecting to virtually any ADSL Service Providers system provided you have correctly configured the Routers settings for your ISPs connection type. Your connection settings are provided to you by your ISP. To configure the Router with the settings that your ISP gave you, click Connection Type (A) on the left side of the screen. Select the connection type you use. If your ISP gave you DNS settings, clicking DNS

(B) allows you to enter DNS address entries for ISPs that require specific settings. When you have finished making settings, the Internet Status indicator will read Connection OK if your Router is set up properly. A B 22 UNDERSTANDING THE WEB-BASED USER INTERFACE Connection Type From the Connection Type page, you can select the type of connection you use. Select the type of connection you use by clicking the radio button (1) next to your connection type and then clicking Next (2). 1 2 Setting your ISP Connection Type to PPPoE or PPPoA Enter the PPPoE (Point-to-Point Protocol over Ethernet) or PPPoA information in the provided spaces, and click Next. Click Apply to activate your settings. This information is provided by your ISP. a b c d e f g h i j 23 UNDERSTANDING THE WEB-BASED USER INTERFACE a. Username - Enter the ISP assigned user name. (Assigned by your ISP). b. Password - Enter your password. (Assigned by your ISP). c. Retype Password - Confirm the password. (Assigned by your ISP). d. IP assigned by ISP - Select Yes for automatic IP assignment from your ISP. Select No only if your ISP assigns you a fixed IP address. e. IP address - If you are using a fixed IP address, enter the fixed IP address supplied by your ISP. f. Subnet Mask - If you are using a fixed IP address, enter the subnet mask supplied by your ISP. g. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier

(VCI) parameter here. (Assigned by your ISP). h. Encapsulation - Select your encapsulation type (supplied by your ISP) to specify how to handle multiple protocols at the ATM transport layer. VC-MUX: Point-to-Point Protocol over ATM Virtual Circuit Multiplexer (null encapsulation) allows only one protocol running per virtual circuit with fewer overheads. LLC: Point-to-Point Protocol over ATM Logical Link Control allows multiple protocols running over one virtual circuit (more overhead). i. Dial on Demand - By selecting Dial on Demand your Router will automatically connect to the Internet when a user opens up a web browser. j. Idle Time (Minutes) - Enter the maximum idle time for the Internet connection. After this time has been exceeded, the connection will be terminated. 24 UNDERSTANDING THE WEB-BASED USER INTERFACE Setting your ISP Connection Type to Disable Internet Sharing VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier

(VCI) parameter here. (Assigned by your ISP). Encapsulation - Select LLC or VC MUX. (Assigned by your ISP). Setting your ISP Connection Type to Multiple Protocol over ATM a b c d e a. WAN IP - Enter an IP address for the Wireless ADSL Modem Router WAN interface. (Assigned by your ISP). b. Subnet Mask - Enter a subnet mask. (Assigned by your ISP). c. Default Route - Enter a default gateway IP address. If the Wireless ADSL Modem Router cannot find the destination address within its local network, it will forward the packets to the Default Gateway. (Assigned by your ISP). d. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier

(VCI) parameter here. (Assigned by your ISP). e. Encapsulation - Select LLC or VC MUX. (Assigned by your ISP). 25 UNDERSTANDING THE WEB-BASED USER INTERFACE DNS (Domain Name Server) Settings A Domain Name Server is a server located on the Internet that translates Universal Resource Links (URLs) like www.belkin.com to IP addresses. Many ISPs do not require you to enter this information into the Router. The Automatic from ISP box (1) should be checked if your ISP did not give you a specific DNS address. If you are using a static IP connection type, then you may need to enter a specific DNS address and secondary DNS address for your connection to work properly. If your connection type is dynamic or PPPoE, it is likely that you do not have to enter a DNS address. Leave the Automatic from ISP box checked. To enter the DNS address settings, uncheck the Automatic from ISP box and enter your DNS entries in the spaces provided. Click Apply Changes (2) to save the settings. 1 2 3. Wireless The Wireless tab lets you make changes to the wireless network settings. From this tab, you can make changes to the wireless network name (SSID), operating channel, and encryption security settings. Channel and SSID Changing the Wireless Channel There are a number of operating channels you can choose from. In the United States, there are 11 channels. In the United Kingdom and most of Europe, there are 13 channels. In a small number of other countries, there are other channel 26 UNDERSTANDING THE WEB-BASED USER INTERFACE requirements. Your Router is configured to operate on the proper channels for the country you reside in. The default channel is 11 (unless you are in a country that does not allow channel 11). The channel can be changed if needed. If there are other wireless networks operating in your area, your network should be set to operate on a channel that is different than the other wireless networks. For best performance, use a channel that is at least five channels away from the other wireless network. For instance, if another network is operating on channel 11, then set your network to channel 6 or below. To change the channel, select the channel from the drop-down list. Click Apply Changes. The change is immediate. Changing the Wireless Network Name (SSID) To identify your wireless network, a name called the SSID (Service Set Identifier) is used. The default SSID of the Router is belkin54g. You can change this to anything you want to or you can leave it unchanged. If there are other wireless networks operating in your area, you will want to make sure that your SSID is unique (does not match that of another wireless network in the area). To change the SSID, type in the SSID that you want to use in the SSID field (1) and click Apply Changes (2). The change is immediate. If you make a change to the SSID, your wireless-equipped computers may also need to be reconfigured to connect to your new network name. Refer to the documentation of your wireless network adapter for information on making this change. 27 UNDERSTANDING THE WEB-BASED USER INTERFACE 1 2 Using the ESSID Broadcast Feature For security purposes, you can choose not to broadcast your networks SSID. Doing so will keep your network name hidden from computers that are scanning for the presence of wireless networks. To turn off the broadcast of the SSID, select DISABLE and then click Apply Changes. The change is immediate. Each computer now needs to be set to connect to your specific SSID; an SSID of ANY will no longer be accepted. Refer to the documentation of your wireless network adapter for information on making this change. Note: This advanced feature should be employed by advanced users only. Using the Wireless Mode Switch Your Router can operate in three different wireless modes: Mixed, 11g Only, and 11b Only. The different modes are explained next. Mixed - In this mode, the Router is compatible with 802.11b and 802.11g wireless clients simultaneously. This mode is the factory default and ensures full compatibility with Wi-Fi-compatible devices. Set the Router to Mixed mode if you have a mix of 802.11b and 802.11g clients in your network. This is the recommended setting for your router and should only be changed if you have a specific reason to do so. 28 UNDERSTANDING THE WEB-BASED USER INTERFACE 11g Only Mode - 11g Only mode is compatible with 802.11g clients only. This mode can be useful only if you do not have any 802.11b clients that need access to the network. To switch modes, select the desired mode from the drop-down box next to Wireless Mode then click Apply Changes. 11b Only Mode - It is not recommended you use this mode unless you have a very specific reason to do so. This mode exists only to solve unique problems that may occur with some 802.11b client adapters and is NOT necessary for interoperability of 802.11g and 802.11b standards. Note: Switching to 11b Only mode will decrease 802.11g performance to 11Mbps. g Nitro Enabling g Nitro allows the Router to use Frame Bursting to get the maximum throughput from the Router to 802.11g clients. g Nitro throughput is up to 50%

faster than any standard 802.11g equipment. g Nitro will work with 802.11g clients that support g Nitro. Encryption/Security Changing the Wireless Security Settings Your Router is equipped with the latest security standard called WPA (Wireless Protected Access). It also supports the legacy security standard called WEP

(Wired Equivalent Privacy). By default, wireless security is disabled. To enable security, you will need to determine which standard you want to use. To access the Security settings, click Security on the Wireless tab. Setting WPA Security Note: To use WPA security, your clients must be upgraded to drivers and software that support WPA. At the time this manual was published, a security patch from Microsoft is available for free download. This patch works only with Windows XP. You also need to download the latest driver for your Belkin 802.11g Wireless Notebook Network Card from the Belkin support site. Other operating systems are not supported at this time. Only Belkin 802.11g clients support WPA at this time. 29 UNDERSTANDING THE WEB-BASED USER INTERFACE There are two types of WPA security, WPA-PSK (no server) and WPA (with server). WPA-PSK uses what is known as a pre-shared key as the security key. A pre-shared key is basically a password that is between 8 and 40 characters long. It can be a combination of letters, numbers, or characters. Each client uses the same key to access the network. Typically, this is the mode that will be used in a home environment. WPA (with server) is a system where a radius server distributes the keys to the clients automatically. This is typically found in a business environment. Setting WPA-PSK (no server) 1. From the Security Mode drop-down menu, select WPA-PSK (no server). 2. Enter your pre-shared key. This can be from 8 to 40 characters and can be letters, numbers, or symbols. This same key must be used on all of the clients that you set up. 3. Click Apply Changes to finish. You must now set all clients to match these settings. Setting WPA (with server) Settings If your network uses a radius server to distribute keys to the clients, use this setting. 30 UNDERSTANDING THE WEB-BASED USER INTERFACE 1. From the Security Mode drop-down menu, select WPA (with server). 2. Enter the IP address of the radius server into the Radius Server fields. 3. Enter the radius key into the Radius Key field. 4. Enter the key interval. Key interval is how often the keys are distributed (in packets). 5. Click Apply Changes to finish. You must now set all clients to match these settings. Setting WEP Encryption Note to Mac users: The Passphrase option will not operate with Apple AirPort. To configure encryption for your Mac computer, set the encryption using the manual method described in the next section. 1. Select 128-bit WEP or 64-bit WEP from the drop-down menu. 31 UNDERSTANDING THE WEB-BASED USER INTERFACE 2. After selecting your WEP encryption mode, you can enter you WEP key manually by typing in the HEX WEP key manually, or you can type in a Passphrase in the Passphrase field and click Generate to create a WEP key from the passphrase. Click Apply Changes to finish. You must now set all of your clients to match these settings. 3. Encryption in the Router is now set. Each of your computers on your wireless network will now need to be configured with the same passphrase. Refer to the documentation of your wireless network adapter for information on making this change. Using a Hexadecimal Key A hexadecimal key is a mixture of numbers and letters from AF and 09. 64-bit keys are five two-digit numbers. 128-bit keys are 13 two-digit numbers. For instance:

AF 0F 4B C3 D4 = 64-bit key C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit key In the boxes below, make up your key by writing in two characters between AF and 09. You will use this key to program the encryption settings on your Router and your wireless computers. 32 UNDERSTANDING THE WEB-BASED USER INTERFACE Note to Mac users: Original Apple AirPort products support 64-bit encryption only. Apple AirPort 2 products can support 64-bit or 128-bit encryption. Please check your product to see which version you are using. If you cannot configure your network with 128-bit encryption, try 64-bit encryption. 4. Firewall Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including:

IP Spoofing Land Attack Ping of Death (PoD) Denial of Service (DoS) IP with zero length Smurf Attack TCP Null Scan SYN flood UDP flooding Tear Drop Attack ICMP defect RIP defect Fragment flooding The firewall also masks common ports that are frequently used to attack networks. These ports appear to be Stealth, meaning that essentially they do not exist to a would-be hacker. You can turn the firewall function off if needed, however, it is recommended that you leave the firewall enabled. Disabling the firewall protection will not leave your network completely vulnerable to hacker attacks, but it is recommended that you leave the firewall enabled. 33 UNDERSTANDING THE WEB-BASED USER INTERFACE Application Gateways Settings Application gateways let you select ports to be open for certain applications to work properly with the Network Address Translation (NAT) feature of the Router. A list of popular applications has been included to choose from. Select your application from the drop-down list from the bottom of the screen. If your application is not here, you will need to check with the application vendor to determine which ports need to be configured. You can manually input this port information into the Router. Choosing an Application Select the row that you want to copy the settings to from the drop-down list, select the row you want to copy to, and then click Copy To. The settings will be transferred to the row you specified. Click Apply Changes to save the setting for that application. 34 UNDERSTANDING THE WEB-BASED USER INTERFACE Virtual Servers Virtual Servers allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications, through your Router to your internal network. Since your internal computers are protected by a firewall, machines from the Internet cannot get to them because they cannot be seen. If you need to configure the Virtual Server function for a specific application, you will need to contact the application vendor to find out which port settings you need. Entering Settings into the Virtual Server To enter settings, enter the last digit of your LAN IP address in the space provided for the internal machine, input the Protocol Type (TCP or UDP), and the LAN Port & Public Port number required to pass, select Enable and click Set. Opening ports in your firewall can pose a security risk. You can enable and disable settings very quickly. It is recommended that you disable the settings when you are not using a specific application. Client IP Filters The Router can be configured to restrict access to the Internet, e-mail, or other network services at specific days and times. Restriction can be set for a single computer, a range of computers, or multiple computers. 35 UNDERSTANDING THE WEB-BASED USER INTERFACE Access Control Access Control allows users to define the outgoing traffic permitted or denied access through the WAN interface. The default is to permit all outgoing traffic. To configure restrictive access to your computers, do the following:

1. Click Add PC on the Access Control screen. 2. Define the appropriate settings for client PC services (as shown on the following screen). 3. Click OK and then click Apply Changes to save your settings. 36 UNDERSTANDING THE WEB-BASED USER INTERFACE URL Blocking To configure the URL Blocking feature, specify the websites

(www.anywebsite.com) and or keywords you want to filter on your network. Click Apply Changes to activate the change. To complete this configuration, you will need to create or modify an access rule in the Client IP filters section. To modify an existing rule, click the Edit option next to the rule you want to modify. To create a new rule, click on the Add PC option. From the Access Control > Add PC section, check the option for WWW with URL Blocking in the Client PC Service table to filter out the websites and keywords specified. Schedule Rule You may filter Internet access for local clients based on rules. Each access control rule may be activated at a scheduled time. Define the schedule on the Schedule Rule, and apply the rule on the Access Control page. 37 UNDERSTANDING THE WEB-BASED USER INTERFACE Follow these steps to add a schedule:

1. Click Add Schedule Rule. 2. You will see the following screen. 3. To configure the Schedule Rule, specify the Name, Comment, Start Time, and End Time that you want to filter on your network. 4. Click OK and then Apply Changes to save your settings. 5. To complete this configuration, you will need to create or modify an access rule in the Client IP filters section. This activates the schedule for use in the Access Control page. MAC Address Filtering The MAC Address Filter is a powerful security feature that allows you to specify which computers are allowed on the network. Any computer attempting to access the network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client on your network to allow network access to each, or copy the MAC address by selecting the name of the computer from the DHCP Client List. To enable this feature, select Enable. Next, click Apply Changes to save the settings. 38 UNDERSTANDING THE WEB-BASED USER INTERFACE DMZ (Demilitarized Zone) If you have a client PC that cannot run an Internet application properly from behind the firewall, you can open the client up to unrestricted two-way Internet access. This may be necessary if the NAT feature is causing problems with an application such as a game or video conferencing application. Use this feature on a temporary basis. The computer in the DMZ is not protected from hacker attacks. 39 UNDERSTANDING THE WEB-BASED USER INTERFACE To put a computer in the DMZ, enter the last digits of its LAN IP address in the Static IP field and click Apply Changes for the change to take effect. If you are using multiple Public (WAN) IP addresses, it is possible to select which Public (WAN) IP address the DMZ host will be directed to. Type in the Public (WAN) IP address you wish the DMZ host to direct to, enter the last two digits of the IP address of the DMZ host computer, and click Apply Changes. Utilities The Utilities screen lets you manage different parameters of the Router and perform certain administrative functions. Restart Router Sometimes it may be necessary to restart or reboot the Router if it begins working improperly. Restarting or rebooting the Router will NOT delete any of your configuration settings. 40

UNDERSTANDING THE WEB-BASED USER INTERFACE Restarting the Router to Restore Normal Operation 1. Click the Restart Router button. 2. The following message will appear. Click OK to restart your Router. Restore Factory Defaults Using this option will restore all of the settings in the Router to the factory

(default) settings. It is recommended that you back up your settings before you restore all of the defaults. 1. Click the Restore Defaults button. 2. The following message will appear. Click OK to restore factory defaults. 41 UNDERSTANDING THE WEB-BASED USER INTERFACE Saving/Backup Current Settings You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you back up your current configuration before performing a firmware update. 1. Click Save. A window called File Download will open. Click Save. 2. A window will open that allows you to select the location in which to save the configuration file. Select a location. There are no restrictions on the file name, however, be sure to name the file so you can locate it yourself later. When you have selected the location and entered the file name, click Save. 42 UNDERSTANDING THE WEB-BASED USER INTERFACE 3. When the save is complete, you will see the window below. Click Close. The configuration is now saved. Restore Previous Settings This option will allow you to restore a previously saved configuration. 1. Click Browse. A window will open that allows you to select the location of the configuration file. All configuration files end with a .bin. Locate the configuration file you want to restore and double-click on it. 2. Then, click Restore. 43 UNDERSTANDING THE WEB-BASED USER INTERFACE Firmware Update From time to time, Belkin may release new versions of the Routers firmware. Firmware updates contain feature improvements and fixes to problems that may have existed. When Belkin releases new firmware, you can download the firmware from the Belkin update website and update your Routers firmware to the latest version. Updating the Routers Firmware 1. In the Firmware Update page, click Browse. A window will open that allows you to select the location of the firmware update file. 2. Browse to the firmware file you downloaded. Select the file by double-clicking on the file name. 3. Click Update to upgrade to the latest firmware version. System Settings The System Settings page is where you can enter a new administrator password, set the time zone, enable remote management, and turn on and off the UPnP function of the Router. 44 UNDERSTANDING THE WEB-BASED USER INTERFACE Setting or Changing the Administrator Password The Router ships with NO password entered. If you wish to add a password for greater security, you can set a password here. Write down your password and keep it in a safe place, as you will need it if you need to log into the Router in the future. It is also recommended that you set a password if you plan to use the remote management feature of your Router. Changing the Login Time-Out Setting The login time-out option allows you to set the period of time that you can be logged into the Routers advanced setup interface. The timer starts when there has been no activity. For example, you have made some changes in the advanced setup interface, then left your computer alone without clicking Logout. Assuming the time-out is set to 10 minutes, then 10 minutes after you leave, the login session will expire. You will have to login to the Router again to make any more changes. The login time-out option is for security purposes and the default is set to 10 minutes. Note: Only one computer can be logged into the Routers advanced setup interface at one time. Setting the Time and Time Zone The Router keeps time by connecting to a Simple Network Time Protocol (SNTP) server. This allows the Router to synchronize the system clock to the global Internet. The synchronized clock in the Router is used to record the security log and control client filtering. Select the time zone that you reside in. The system clock may not update immediately. Allow at least 15 minutes for the Router to contact the timeservers on the Internet and get a response. You cannot set the clock yourself. 45 UNDERSTANDING THE WEB-BASED USER INTERFACE Enabling Remote Management Before you enable this advanced feature of your Belkin Router, MAKE SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD. Remote management allows you to make changes to your Routers settings from anywhere on the Internet. There are two methods of remotely managing the Router. The first is to allow access to the Router from anywhere on the Internet by selecting Any IP address can remotely manage the Router. By typing in your WAN IP address from any computer on the Internet, you will be presented with a login screen where you need to type in the password of your Router. The second method is to allow a specific IP address only to remotely manage the Router. This is more secure, but less convenient. To use this method, enter the IP address you know you will be accessing the Router from in the space provided and select Only this IP address can remotely manage the Router. Before you enable this function, it is STRONGLY RECOMMENDED that you set your administrator password. Leaving the password empty will potentially open your Router to intrusion. 46 UNDERSTANDING THE WEB-BASED USER INTERFACE Enabling/Disabling UPnP UPnP (Universal Plug-and-Play) is yet another advanced feature offered by your Belkin Router. It is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-

compliant. Some applications require the Routers firewall to be configured in a specific way to operate properly. This usually requires opening TCP and UDP ports, and in some instances, setting trigger ports. An application that is UPnP-

compliant has the ability to communicate with the Router, basically telling the Router which way it needs the firewall configured. The Router ships with the UPnP feature disabled. If you are using any applications that are UPnP-

compliant, and wish to take advantage of the UPnP features, you can enable the UPnP feature. Simply select Enable in the UPnP Enabling section of the Utilities page. Click Apply Changes to save the change. 47 MANUALLY CONFIGURING NETWORK SETTINGS Set up the computer that is connected to the ADSL modem FIRST using these steps. You can also use these steps to add computers to your Router after the Router has been set up to connect to the Internet. Manually Configuring Network Settings in Mac OS up to 9.x 1. Pull down the Apple menu. Select Control Panels and select TCP/IP. 2. You will see the TCP/IP control panel. Select Ethernet Built-In or Ethernet in the Connect via: drop-down menu (1). 1 2 3. Next to Configure (2), if Manually is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router. 48 MANUALLY CONFIGURING NETWORK SETTINGS 4. If not already set, at Configure:, choose Using DHCP Server. This will tell the computer to obtain an IP address from the Router. 5. Close the window. If you made any changes, the following window will appear. Click Save. Restart the computer. When the computer restarts, your network settings are now configured for use with the Router. Manually Configuring Network Settings in Mac OS X 1. Click on the System Preferences icon. 2. Select Network (1) from the System Preferences menu. 1 49 MANUALLY CONFIGURING NETWORK SETTINGS 3. Select Built-in Ethernet (2) next to Show in the Network menu. 2 3 4 5 4. Select the TCP/IP tab (3). Next to Configure (4), you should see Manually or Using DHCP. If you do not, check the PPPoE tab (5) to make sure that Connect using PPPoE is NOT selected. If it is, you will need to configure your Router for a PPPoE connection type using your user name and password. 5. If Manually is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router. 6. If not already selected, select Using DHCP next to Configure (4), then click Apply Now. Your network settings are now configured for use with the Router. 50 MANUALLY CONFIGURING NETWORK SETTINGS Manually Configuring Network Settings in Windows 2000, NT, or XP 1. Click Start, Settings, then Control Panel. 2. Double-click on the Network and dial-up connections icon (Windows 2000) or the Network icon (Windows XP). 3. Right-click on the Local Area Connection associated with your network adapter and select Properties from the drop-down menu. 4. In the Local Area Connection Properties window, click Internet Protocol

(TCP/IP) and click the Properties button. The following screen will appear:

1 2 3 5. If Use the following IP address (2) is selected, your Router will need to be set up for a static IP connection type. Write the address information the table below. You will need to enter this information into the Router. 6. If not already selected, select Obtain an IP address automatically (1) and Obtain DNS server address automatically (3). Click OK. Your network settings are now configured for use with the Router. 51 MANUALLY CONFIGURING NETWORK SETTINGS Manually Configuring Network Settings in Windows 98 or Me 1. Right-click on My Network Neighborhood and select Properties from the drop-down menu. 2. Select TCP/IP > Settings for your installed network adapter. You will see the following window. 1 2 3 3. If Specify and IP address is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router. 4. Write the IP address and subnet mask from the IP Address tab (3). 5. Click the Gateway tab (2). Write the gateway address down in the chart. 6. Click the DNS Configuration tab (1). Write the DNS address(es) in the chart. 7. If not already selected, select Obtain IP address automatically on the IP address tab. Click OK. Restart the computer. When the computer restarts, your network settings are now configured for use with the Router. 52 MANUALLY CONFIGURING NETWORK SETTINGS Recommended Web Browser Settings In most cases, you will not need to make any changes to your web browsers settings. If you are having trouble accessing the Internet or the Web-Based Advanced User Interface, then change your browsers settings to the recommended settings in this section. Microsoft Internet Explorer 4.0 or Higher 1. Start your web browser. Select Tools then Internet Options. 2. In the Internet Options screen, there are three selections: Never dial a connection, Dial whenever a network connection is not present, and Always dial my default connection. If you can make a selection, select Never dial a connection. If you cannot make a selection, go to the next step. 3. Under the Internet Options screen, click on Connections and select LAN Settings. 53 MANUALLY CONFIGURING NETWORK SETTINGS 4. Make sure there are no check marks next to any of the displayed options:

Automatically detect settings, Use automatic configuration script, and Use a proxy server. Click OK. Then click OK again in the Internet Options page. Netscape Navigator 4.0 or Higher 1. Start Netscape. Click on Edit then Preferences. 2. In the Preferences window, click on Advanced then select Proxies. In the Proxies window, select Direct connection to the Internet. 54 GLOSSARY IP address The IP address is the Internal IP address of the Router. To access the advanced setup interface, type this IP address into the address bar of your browser. This address can be changed if needed. To change the IP address, type in the new IP address and click Apply Changes. The IP address you choose should be a non-routable IP. Examples of a non-routable IP are:

192.168.x.x (where x is anything between 0 and 255.) 10.x.x.x (where x is anything between 0 and 255.) Subnet Mask Some networks are far too large to allow all traffic to flood all its parts. These networks must be broken down into smaller, more manageable sections, called subnets. The subnet mask is the network address plus the information reserved for identifying the subnetwork. DNS DNS is an acronym for Domain Name Server. A Domain Name Server is a server located on the Internet that translates URLs (Universal Resource Links) like www.belkin.com to IP addresses. Many ISPs do not require you to enter this information into the Router. If you are using a static IP connection type, then you may need to enter a specific DNS address and secondary DNS address for your connection to work properly. If your connection type is Dynamic or PPPoE, it is likely that you do not have to enter a DNS address. PPPoE (Routing Mode, for multiple PCs) Most ADSL providers use PPPoE as the connection type. If you use an ADSL modem to connect to the Internet, your ISP may use PPPoE to log you into the service. Your connection type is PPPoE if:

1. Your ISP gave you a user name and password which is required to connect to the Internet 2. Your ISP gave you software such as WinPoET, Enternet300 that you use to connect to the Internet 55 GLOSSARY 3. You have to double-click on a desktop icon other than your browser to get on the Internet To set the Router to use PPPoE, type in your user name and password in the spaces provided. After you have typed in your information, click Apply Changes. After you apply the changes, the Internet Status indicator will read connection OK if your Router is set up properly. PPPoA (Routing Mode, for multiple PCs) Enter the PPPoA information in the provided spaces, and click Next. Click Apply to activate your settings. a. User name - Enter the ISP assigned user name. (Assigned by your ISP). b. Password - Enter your password. (Assigned by your ISP). c. Retype Password - Confirm the password. (Assigned by your ISP). d. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier

(VCI) parameter here. (Assigned by your ISP). Disconnect after X... This feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time. For instance, placing a check mark next to this option and entering 5 into the minute field will cause the Router to disconnect from the Internet after five minutes of no Internet activity. This option should be used if you pay for your Internet service by the minute. Channel and SSID To change the channel of operation of the Router, select the desired channel from the drop-down menu and select your channel. Click Apply Changes to save the setting. You can also change the SSID. The SSID is the equivalent to the wireless network's name. You can make the SSID anything you want to. If there are other wireless networks in your area, you should give your wireless network a unique name. Click inside of the SSID box and type in a new name. Click Apply Changes to make the change. 56 GLOSSARY ESSID Broadcast Many wireless network adapters currently on the market possess a feature known as site survey. It scans the air for any available network and allows each computer to automatically select a network from the survey. This occurs if the computers SSID is set to "ANY. Your Belkin Router can block this random search for a network. If you disable the "ESSID Broadcast" feature, the only way a computer can join your network is by its SSID being set to the specific name of the network (like WLAN). Be sure that you know your SSID (network name) before enabling this feature. It is possible to make your wireless network nearly invisible. By turning off the broadcast of the SSID, your network will not appear in a site survey. Obviously, turning off the broadcast feature of the SSID helps increase security. Encryption Setting encryption can help keep your network secure. The Router uses Wired Equivalent Privacy (WEP) encryption to protect your data and features two rates of encryption: 64-bit and 128-bit. Encryption works on a system of keys. The key on the computer must match the key on the Router, and there are two ways to make a key. The easiest is to let the Routers software convert a passphrase youve created into a key. The advanced method is to enter the keys manually. Application Gateways Application Gateways let you specify specific ports to be open for specific applications to work properly with the Network Address Translation (NAT) feature of the Router. A list of popular applications has been included. You can select an application from the popular choices included in the drop-down list. Your selections will be programmed into the Router. From the drop-down list, select the row that you want to copy the settings from, and the row you want to copy to, and then click "Copy To". The settings will be transferred to the row you specified. Click "Apply Changes" to save the setting for that application. If your application is not here, you will need to check with the application vendor to determine which ports need to be configured. You can manually input this port information into the Router. 57 GLOSSARY Virtual Servers This function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Router to your internal network. Since your internal computers are protected by a firewall, machines from the Internet cannot get to them because they cannot be seen. If you need to configure the Virtual Server function for a specific application, you will need to contact the application vendor to find out which port settings you need. To manually enter settings, enter the IP address in the space provided for the internal machine, the port type (TCP or UDP), and the LAN

& Public port(s) required to pass, select Enable and click Set. You can only pass one port per internal IP address. Opening ports in your firewall can pose a security risk. You can enable and disable settings very quickly. It is recommended that you disable the settings when you are not using a specific application. Client IP filters The Router can be configured to restrict access to the Internet, e-mail or other network services at specific days and times. Restriction can be set for a single computer, a range of computers, or multiple computers. URL Blocking To configure the URL Blocking feature, specify the websites (www.somesite.com) and or keywords you want to filter on your network. Click Apply Changes to activate the change. To complete this configuration, you will need to create or modify an access rule in the Client IP filters section. To modify an existing rule, click the Edit option next to the rule you want to modify. To create a new rule, click on the Add PC option. From the Access Control Add PC section, check the option for WWW with URL Blocking in the Client PC Service table to filter out the websites and keywords specified. Schedule Rule To configure the Schedule Rule, specify the Name, Comment, Start Time, and End Time that you want to filter on your network. This page defines schedule rule names and activates the schedule for use in the Access Control page. 58 GLOSSARY MAC Address Filtering The MAC Address Filter is a powerful security feature that allows you to specify which computers are allowed on the network. Any computer attempting to access the network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client on your network to allow network access to each or copy the MAC address by selecting the name of the computer from the DHCP Client List. To enable this feature, select Enable. Next, click Apply Changes to save the settings. DMZ If you have a client PC that cannot run an Internet application properly from behind the firewall, you can open the client up to unrestricted two-way Internet access. This may be necessary if the NAT feature is causing problems with an application such as a game or video conferencing application. Use this feature on a temporary basis. The computer in the DMZ is not protected from hacker attacks. To put a computer in the DMZ, enter the last digits of its LAN IP address in the Static IP field and click Apply Changes for the change to take effect. If you have only one Public (WAN) IP address, then you can leave the Public IP to 0.0.0.0. If you are using multiple Public (WAN) IP addresses, it is possible to select which Public (WAN) IP address the DMZ host will be directed to. Type in the Public (WAN) IP address you wish the DMZ host to direct to, enter the last two digits of the IP address of the DMZ host computer, and click Apply Changes. Administrator Password The Router ships with NO password entered. If you wish to add a password for more security, you can set a password from your Routers web-based user interface. Keep your password in a safe place as you will need this password if you need to log into the Router in the future. It is STRONGLY RECOMMENDED that you set a password if you plan to use the remote management feature. The login time-out option allows you to set the period of time that you can be logged into the Router's advanced setup interface. The timer starts when there has been no activity. For example, you have made some changes in the advanced setup interface, then left your computer alone without clicking Logout. 59 GLOSSARY Assuming the time-out is set to 10 minutes, then 10 minutes after you leave, the login session will expire. You will have to login to the Router again to make any more changes. The login time-out option is for security purposes and the default is set to 10 minutes. Note, only one computer can be logged into the Routers advanced setup interface at a time. Time and Time Zone The Router keeps time by connecting to a Simple Network Time Protocol (SNTP) server. This allows the Router to synchronize the system clock to the global Internet. The synchronized clock in the Router is used to record the security log and control client filtering. Select the time zone that you reside in. If you reside in an area that observes daylight saving time, then place a check mark in the box next to Enable Daylight Saving. The system clock may not update immediately. Allow at least 15 minutes for the Router to contact the timeservers on the Internet and get a response. You cannot set the clock yourself. Remote Management Before you enable this function, MAKE SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD. Remote management allows you to make changes to your Routers settings from anywhere on the Internet. UPnP UPnP (Universal Plug-and-Play) is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-

compliant. Some applications require the Router's firewall to be configured in a specific way to operate properly. This usually requires opening TCP and UDP ports and in some instances setting trigger ports. An application that is UPnP-

compliant has the ability to communicate with the Router, basically telling the Router which way it needs the firewall configured. The Router ships with the UPnP feature disabled. If you are using any applications that are UPnP-

compliant, and wish to take advantage of the UPnP features, you can enable the UPnP feature. Simply select Enable in the UPnP Enabling section of the Utilities page. Click Apply Changes to save the change. 60 TROUBLESHOOTING You can find technical support information at www.belkin.com/networking or www.belkin.com through the tech support area. If you want to contact technical support by phone, please call 877-736-5771. Technical support is available 24-hours-a-day, 7-days-a-week. Problem Possible Cause/Solution The ADSL SYN LED is not on. The ADSL Data LED is not on. 1. Check the connection between the Modem Router and ADSL line. Make sure the cable from the ADSL line is connected to the port on the Router labeled ADSL. 2. Make sure the Router has power. The PWR LED of the front panel should be illuminated. 1. Make sure the cable from the ADSL line is connected to the port on the Router labeled ADSL and the SYN LED is on. 2. Make sure you have the correct VPI/VCI, user name, and password from your ISP provider. My connection type is static IP address. I cannot connect to the Internet. Since your connection type is static IP address, your ISP must assign you the IP address, subnet mask, and gateway address. Instead of using the Wizard, go to Connection Type, and then select your connection type. Click Next, select Static IP, and enter your IP address, subnet mask, and default gateway information. 61 TROUBLESHOOTING Ive forgotten or lost my password. Press the Reset button on the rear panel

(holding it down for at least five seconds) to restore the factory defaults. My wireless PC cannot connect to the Router. 1. Make sure the wireless PC has the same SSID settings as the Router, and you have the same security settings on the clients such as WPA or WEP encryption. 2. Make sure the distance between the Router and wireless PC are not too far away. The wireless network is often interrupted. 1. Move your wireless PC closer to the Router to find a better signal. 2. There may also be interference, possibly caused by a microwave oven or 2.4GHz cordless phones. Change the location of the Router or use a different wireless channel. 62 INFORMATION FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin Corporation, of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the product, F5D7630-4 to which this declaration relates, complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Exposure to Radio Frequency Radiation. The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such manner that the potential for human contact normal operation is minimized. When connecting an external antenna to the device, the antenna shall be placed in such a manner to minimize the potential for human contact during normal operation. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the distance between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Modifications The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by Belkin Corporation may void the users authority to operate the equipment. 63 INFORMATION Canada-Industry Canada (IC) The wireless radio of this device complies with RSS 139 & RSS 210 Industry Canada. This Class B digital complies with Canadian ICES-003. Cet appareil numrique de la classe B conforme la norme NMB-003 du Canada. Europe-European Union Notice Radio products with the CE 0682 or CE alert marking comply with the R&TTE Directive (1995/5/EC) issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European Norms (in brackets are the equivalent international standards). EN 60950 (IEC60950) Product Safety EN 300 328 Technical requirement for radio equipment ETS 300 826 General EMC requirements for radio equipment. To determine the type of transmitter, check the identification label on your Belkin product. Products with the CE marking comply with the EMC Directive (89/336/EEC) and the Low Voltage Directive (72/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms (in brackets are the equivalent international standards). EN 55022 (CISPR 22) Electromagnetic Interference EN 55024 (IEC61000-4-2,3,4,5,6,8,11)- Electromagnetic Immunity EN 61000-3-2 (IEC610000-3-2) - Power Line Harmonics EN 61000-3-3 (IEC610000) Power Line Flicker EN 60950 (IEC60950) Product Safety Products that contain the radio transmitter are labeled with CE 0682 or CE alert marking and may also carry the CE logo. 64 INFORMATION Belkin Corporation Limited Lifetime Product Warranty Belkin Corporation warrants this product against defects in materials and workmanship for its lifetime. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product. Proof of purchase may be required. This warranty does not apply if the product has been damaged by accident, abuse, misuse, or misapplication; if the product has been modified without the written permission of Belkin; or if any Belkin serial number has been removed or defaced. THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE IN LIEU OF ALL OTHERS, WHETHER ORAL OR WRITTEN, EXPRESSED OR IMPLIED. BELKIN SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No Belkin dealer, agent, or employee is authorized to make any modification, extension, or addition to this warranty. BELKIN IS NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO, LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPROGRAMMING OR REPRODUCING ANY PROGRAM OR DATA STORED IN, OR USED WITH, BELKIN PRODUCTS. Some states do not allow the exclusion or limitation of incidental or consequential damages or exclusions of implied warranties, so the above limitations of exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. 65 belkin.com Belkin Corporation 501 West Walnut Street Compton CA 90220 USA Tel: 310.898.1100 Fax: 310.898.1111 Belkin Components, Ltd. Express Business Park Shipton Way Rushden NN10 6GL United Kingdom Tel: +44 (0) 1933 35 2000 Fax: +44 (0) 1933 31 2000 Belkin Components B.V. Starparc Building Boeing Avenue 333 1119 PH Schiphol-Rijk The Netherlands Tel: +31 (0) 20 654 7300 Fax: +31 (0) 20 654 7349 Belkin, Ltd. 7 Bowen Crescent West Gosford NSW 2250 Australia Tel: +61 (0) 2 4372 8600 Fax: +61 (0) 2 4372 8603 Belkin Tech Support US: 877.736.5771 310.898.1100 ext. 2263 Europe: 00 800 223 55 460 Australia: 1800 666 040 23MS293 2003 Belkin Corporation. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. Mac, Mac OS, AppleTalk, Apple, and AirPort are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.